drivers/serial/serial_pl01x.c - filogic/uboot - Gitiles

 // SPDX-License-Identifier: GPL-2.0+
 /*
  * (C) Copyright 2000
  * Rob Taylor, Flying Pig Systems. robt@flyingpig.com.
  *
  * (C) Copyright 2004
  * ARM Ltd.
  * Philippe Robin, <philippe.robin@arm.com>
  */

 /* Simple U-Boot driver for the PrimeCell PL010/PL011 UARTs */

 #include <asm/global_data.h>
 /* For get_bus_freq() */
 #include <clock_legacy.h>
 #include <dm.h>
 #include <clk.h>
 #include <errno.h>
 #include <watchdog.h>
 #include <asm/io.h>
 #include <serial.h>
 #include <spl.h>
 #include <dm/device_compat.h>
 #include <dm/platform_data/serial_pl01x.h>
 #include <linux/compiler.h>
 #include "serial_pl01x_internal.h"

 DECLARE_GLOBAL_DATA_PTR;

 #if !CONFIG_IS_ENABLED(DM_SERIAL)
 static volatile unsigned char *const port[] = CFG_PL01x_PORTS;
 static enum pl01x_type pl01x_type __section(".data");
 static struct pl01x_regs *base_regs __section(".data");
 #define NUM_PORTS (sizeof(port)/sizeof(port[0]))

 #endif

 static int pl01x_putc(struct pl01x_regs *regs, char c)
 {
 	/* Wait until there is space in the FIFO */
 	if (readl(&regs->fr) & UART_PL01x_FR_TXFF)
 		return -EAGAIN;

 	/* Send the character */
 	writel(c, &regs->dr);

 	return 0;
 }

 static int pl01x_getc(struct pl01x_regs *regs)
 {
 	unsigned int data;

 	/* Wait until there is data in the FIFO */
 	if (readl(&regs->fr) & UART_PL01x_FR_RXFE)
 		return -EAGAIN;

 	data = readl(&regs->dr);

 	/* Check for an error flag */
 	if (data & 0xFFFFFF00) {
 		/* Clear the error */
 		writel(0xFFFFFFFF, &regs->ecr);
 		return -1;
 	}

 	return (int) data;
 }

 static int pl01x_tstc(struct pl01x_regs *regs)
 {
 	schedule();
 	return !(readl(&regs->fr) & UART_PL01x_FR_RXFE);
 }

 static int pl01x_generic_serial_init(struct pl01x_regs *regs,
 				     enum pl01x_type type)
 {
 	switch (type) {
 	case TYPE_PL010:
 		/* disable everything */
 		writel(0, &regs->pl010_cr);
 		break;
 	case TYPE_PL011:
 		/* disable everything */
 		writel(0, &regs->pl011_cr);
 		break;
 	default:
 		return -EINVAL;
 	}

 	return 0;
 }

 static int pl011_set_line_control(struct pl01x_regs *regs)
 {
 	unsigned int lcr;
 	/*
 	 * Internal update of baud rate register require line
 	 * control register write
 	 */
 	lcr = UART_PL011_LCRH_WLEN_8 | UART_PL011_LCRH_FEN;
 	writel(lcr, &regs->pl011_lcrh);
 	return 0;
 }

 static int pl01x_generic_setbrg(struct pl01x_regs *regs, enum pl01x_type type,
 				int clock, int baudrate)
 {
 	switch (type) {
 	case TYPE_PL010: {
 		unsigned int divisor;

 		/* disable everything */
 		writel(0, &regs->pl010_cr);

 		switch (baudrate) {
 		case 9600:
 			divisor = UART_PL010_BAUD_9600;
 			break;
 		case 19200:
 			divisor = UART_PL010_BAUD_19200;
 			break;
 		case 38400:
 			divisor = UART_PL010_BAUD_38400;
 			break;
 		case 57600:
 			divisor = UART_PL010_BAUD_57600;
 			break;
 		case 115200:
 			divisor = UART_PL010_BAUD_115200;
 			break;
 		default:
 			divisor = UART_PL010_BAUD_38400;
 		}

 		writel((divisor & 0xf00) >> 8, &regs->pl010_lcrm);
 		writel(divisor & 0xff, &regs->pl010_lcrl);

 		/*
 		 * Set line control for the PL010 to be 8 bits, 1 stop bit,
 		 * no parity, fifo enabled
 		 */
 		writel(UART_PL010_LCRH_WLEN_8 | UART_PL010_LCRH_FEN,
 		       &regs->pl010_lcrh);
 		/* Finally, enable the UART */
 		writel(UART_PL010_CR_UARTEN, &regs->pl010_cr);
 		break;
 	}
 	case TYPE_PL011: {
 		unsigned int temp;
 		unsigned int divider;
 		unsigned int remainder;
 		unsigned int fraction;

 		/* Without a valid clock rate we cannot set up the baudrate. */
 		if (clock) {
 			/*
 			 * Set baud rate
 			 *
 			 * IBRD = UART_CLK / (16 * BAUD_RATE)
 			 * FBRD = RND((64 * MOD(UART_CLK,(16 * BAUD_RATE)))
 			 *		/ (16 * BAUD_RATE))
 			 */
 			temp = 16 * baudrate;
 			divider = clock / temp;
 			remainder = clock % temp;
 			temp = (8 * remainder) / baudrate;
 			fraction = (temp >> 1) + (temp & 1);

 			writel(divider, &regs->pl011_ibrd);
 			writel(fraction, &regs->pl011_fbrd);
 		}

 		pl011_set_line_control(regs);
 		/* Finally, enable the UART */
 		writel(UART_PL011_CR_UARTEN | UART_PL011_CR_TXE |
 		       UART_PL011_CR_RXE | UART_PL011_CR_RTS, &regs->pl011_cr);
 		break;
 	}
 	default:
 		return -EINVAL;
 	}

 	return 0;
 }

 #if !CONFIG_IS_ENABLED(DM_SERIAL)
 static void pl01x_serial_init_baud(int baudrate)
 {
 	int clock = 0;

 #if defined(CONFIG_PL011_SERIAL)
 	pl01x_type = TYPE_PL011;
 	clock = CFG_PL011_CLOCK;
 #endif
 	base_regs = (struct pl01x_regs *)port[CONFIG_CONS_INDEX];

 	pl01x_generic_serial_init(base_regs, pl01x_type);
 	pl01x_generic_setbrg(base_regs, pl01x_type, clock, baudrate);
 }

 /*
  * Integrator AP has two UARTs, we use the first one, at 38400-8-N-1
  * Integrator CP has two UARTs, use the first one, at 38400-8-N-1
  * Versatile PB has four UARTs.
  */
 int pl01x_serial_init(void)
 {
 	pl01x_serial_init_baud(CONFIG_BAUDRATE);

 	return 0;
 }

 static void pl01x_serial_putc(const char c)
 {
 	if (c == '\n')
 		while (pl01x_putc(base_regs, '\r') == -EAGAIN);

 	while (pl01x_putc(base_regs, c) == -EAGAIN);
 }

 static int pl01x_serial_getc(void)
 {
 	while (1) {
 		int ch = pl01x_getc(base_regs);

 		if (ch == -EAGAIN) {
 			schedule();
 			continue;
 		}

 		return ch;
 	}
 }

 static int pl01x_serial_tstc(void)
 {
 	return pl01x_tstc(base_regs);
 }

 static void pl01x_serial_setbrg(void)
 {
 	/*
 	 * Flush FIFO and wait for non-busy before changing baudrate to avoid
 	 * crap in console
 	 */
 	while (!(readl(&base_regs->fr) & UART_PL01x_FR_TXFE))
 		schedule();
 	while (readl(&base_regs->fr) & UART_PL01x_FR_BUSY)
 		schedule();
 	pl01x_serial_init_baud(gd->baudrate);
 }

 static struct serial_device pl01x_serial_drv = {
 	.name	= "pl01x_serial",
 	.start	= pl01x_serial_init,
 	.stop	= NULL,
 	.setbrg	= pl01x_serial_setbrg,
 	.putc	= pl01x_serial_putc,
 	.puts	= default_serial_puts,
 	.getc	= pl01x_serial_getc,
 	.tstc	= pl01x_serial_tstc,
 };

 void pl01x_serial_initialize(void)
 {
 	serial_register(&pl01x_serial_drv);
 }

 __weak struct serial_device *default_serial_console(void)
 {
 	return &pl01x_serial_drv;
 }
 #else

 static int pl01x_serial_getinfo(struct udevice *dev,
 				struct serial_device_info *info)
 {
 	struct pl01x_serial_plat *plat = dev_get_plat(dev);

 	/* save code size */
 	if (!not_xpl())
 		return -ENOSYS;

 	info->type = SERIAL_CHIP_PL01X;
 	info->addr_space = SERIAL_ADDRESS_SPACE_MEMORY;
 	info->addr = plat->base;
 	info->size = 0x1000;
 	info->reg_width = 4;
 	info->reg_shift = 2;
 	info->reg_offset = 0;
 	info->clock = plat->clock;

 	return 0;
 }

 int pl01x_serial_setbrg(struct udevice *dev, int baudrate)
 {
 	struct pl01x_serial_plat *plat = dev_get_plat(dev);
 	struct pl01x_priv *priv = dev_get_priv(dev);

 	if (!plat->skip_init) {
 		pl01x_generic_setbrg(priv->regs, priv->type, plat->clock,
 				     baudrate);
 	}

 	return 0;
 }

 int pl01x_serial_probe(struct udevice *dev)
 {
 	struct pl01x_serial_plat *plat = dev_get_plat(dev);
 	struct pl01x_priv *priv = dev_get_priv(dev);
 	int ret;

 #if CONFIG_IS_ENABLED(OF_PLATDATA)
 	struct dtd_serial_pl01x *dtplat = &plat->dtplat;

 	priv->regs = (struct pl01x_regs *)dtplat->reg[0];
 	plat->type = dtplat->type;
 #else
 	priv->regs = (struct pl01x_regs *)plat->base;
 #endif
 	priv->type = plat->type;

 	if (!plat->skip_init) {
 		ret = pl01x_generic_serial_init(priv->regs, priv->type);
 		if (ret)
 			return ret;
 		return pl01x_serial_setbrg(dev, gd->baudrate);
 	} else {
 		return 0;
 	}
 }

 int pl01x_serial_getc(struct udevice *dev)
 {
 	struct pl01x_priv *priv = dev_get_priv(dev);

 	return pl01x_getc(priv->regs);
 }

 int pl01x_serial_putc(struct udevice *dev, const char ch)
 {
 	struct pl01x_priv *priv = dev_get_priv(dev);

 	return pl01x_putc(priv->regs, ch);
 }

 int pl01x_serial_pending(struct udevice *dev, bool input)
 {
 	struct pl01x_priv *priv = dev_get_priv(dev);
 	unsigned int fr = readl(&priv->regs->fr);

 	if (input)
 		return pl01x_tstc(priv->regs);
 	else
 		return fr & UART_PL01x_FR_TXFE ? 0 : 1;
 }

 static const struct dm_serial_ops pl01x_serial_ops = {
 	.putc = pl01x_serial_putc,
 	.pending = pl01x_serial_pending,
 	.getc = pl01x_serial_getc,
 	.setbrg = pl01x_serial_setbrg,
 	.getinfo = pl01x_serial_getinfo,
 };

 #if CONFIG_IS_ENABLED(OF_REAL)
 static const struct udevice_id pl01x_serial_id[] ={
 	{.compatible = "arm,pl011", .data = TYPE_PL011},
 	{.compatible = "arm,pl010", .data = TYPE_PL010},
 	{}
 };

 #ifndef CFG_PL011_CLOCK
 #define CFG_PL011_CLOCK 0
 #endif

 int pl01x_serial_of_to_plat(struct udevice *dev)
 {
 	struct pl01x_serial_plat *plat = dev_get_plat(dev);
 	struct clk clk;
 	fdt_addr_t addr;
 	int ret;

 	addr = dev_read_addr(dev);
 	if (addr == FDT_ADDR_T_NONE)
 		return -EINVAL;

 	plat->base = addr;
 	plat->clock = dev_read_u32_default(dev, "clock", CFG_PL011_CLOCK);
 	ret = clk_get_by_index(dev, 0, &clk);
 	if (!ret) {
 		ret = clk_enable(&clk);
 		if (ret && ret != -ENOSYS) {
 			dev_err(dev, "failed to enable clock\n");
 			return ret;
 		}

 		plat->clock = clk_get_rate(&clk);
 		if (IS_ERR_VALUE(plat->clock)) {
 			dev_err(dev, "failed to get rate\n");
 			return plat->clock;
 		}
 		debug("%s: CLK %d\n", __func__, plat->clock);
 	}
 	plat->type = dev_get_driver_data(dev);
 	plat->skip_init = dev_read_bool(dev, "skip-init");

 	return 0;
 }
 #endif

 U_BOOT_DRIVER(serial_pl01x) = {
 	.name	= "serial_pl01x",
 	.id	= UCLASS_SERIAL,
 #if CONFIG_IS_ENABLED(OF_REAL)
 	.of_match = of_match_ptr(pl01x_serial_id),
 	.of_to_plat = of_match_ptr(pl01x_serial_of_to_plat),
 #endif
 	.plat_auto	= sizeof(struct pl01x_serial_plat),
 	.probe = pl01x_serial_probe,
 	.ops	= &pl01x_serial_ops,
 	.flags = DM_FLAG_PRE_RELOC,
 	.priv_auto	= sizeof(struct pl01x_priv),
 };

 DM_DRIVER_ALIAS(serial_pl01x, arm_pl011)
 DM_DRIVER_ALIAS(serial_pl01x, arm_pl010)
 #endif

 #if defined(CONFIG_DEBUG_UART_PL010) || defined(CONFIG_DEBUG_UART_PL011)

 #include <debug_uart.h>

 static void _debug_uart_init(void)
 {
 #ifndef CONFIG_DEBUG_UART_SKIP_INIT
 	struct pl01x_regs *regs = (struct pl01x_regs *)CONFIG_VAL(DEBUG_UART_BASE);
 	enum pl01x_type type;

 	if (IS_ENABLED(CONFIG_DEBUG_UART_PL011))
 		type = TYPE_PL011;
 	else
 		type = TYPE_PL010;

 	pl01x_generic_serial_init(regs, type);
 	pl01x_generic_setbrg(regs, type,
 			     CONFIG_DEBUG_UART_CLOCK, CONFIG_BAUDRATE);
 #endif
 }

 static inline void _debug_uart_putc(int ch)
 {
 	struct pl01x_regs *regs = (struct pl01x_regs *)CONFIG_VAL(DEBUG_UART_BASE);

 	while (pl01x_putc(regs, ch) == -EAGAIN)
 		;
 }

 DEBUG_UART_FUNCS

 #endif
	// SPDX-License-Identifier: GPL-2.0+
	/*
	* (C) Copyright 2000
	* Rob Taylor, Flying Pig Systems. robt@flyingpig.com.
	*
	* (C) Copyright 2004
	* ARM Ltd.
	* Philippe Robin, <philippe.robin@arm.com>
	*/

	/* Simple U-Boot driver for the PrimeCell PL010/PL011 UARTs */

	#include <asm/global_data.h>
	/* For get_bus_freq() */
	#include <clock_legacy.h>
	#include <dm.h>
	#include <clk.h>
	#include <errno.h>
	#include <watchdog.h>
	#include <asm/io.h>
	#include <serial.h>
	#include <spl.h>
	#include <dm/device_compat.h>
	#include <dm/platform_data/serial_pl01x.h>
	#include <linux/compiler.h>
	#include "serial_pl01x_internal.h"

	DECLARE_GLOBAL_DATA_PTR;

	#if !CONFIG_IS_ENABLED(DM_SERIAL)
	static volatile unsigned char *const port[] = CFG_PL01x_PORTS;
	static enum pl01x_type pl01x_type __section(".data");
	static struct pl01x_regs *base_regs __section(".data");
	#define NUM_PORTS (sizeof(port)/sizeof(port[0]))

	#endif

	static int pl01x_putc(struct pl01x_regs *regs, char c)
	{
	/* Wait until there is space in the FIFO */
	if (readl(&regs->fr) & UART_PL01x_FR_TXFF)
	return -EAGAIN;

	/* Send the character */
	writel(c, &regs->dr);

	return 0;
	}

	static int pl01x_getc(struct pl01x_regs *regs)
	{
	unsigned int data;

	/* Wait until there is data in the FIFO */
	if (readl(&regs->fr) & UART_PL01x_FR_RXFE)
	return -EAGAIN;

	data = readl(&regs->dr);

	/* Check for an error flag */
	if (data & 0xFFFFFF00) {
	/* Clear the error */
	writel(0xFFFFFFFF, &regs->ecr);
	return -1;
	}

	return (int) data;
	}

	static int pl01x_tstc(struct pl01x_regs *regs)
	{
	schedule();
	return !(readl(&regs->fr) & UART_PL01x_FR_RXFE);
	}

	static int pl01x_generic_serial_init(struct pl01x_regs *regs,
	enum pl01x_type type)
	{
	switch (type) {
	case TYPE_PL010:
	/* disable everything */
	writel(0, &regs->pl010_cr);
	break;
	case TYPE_PL011:
	/* disable everything */
	writel(0, &regs->pl011_cr);
	break;
	default:
	return -EINVAL;
	}

	return 0;
	}

	static int pl011_set_line_control(struct pl01x_regs *regs)
	{
	unsigned int lcr;
	/*
	* Internal update of baud rate register require line
	* control register write
	*/
	lcr = UART_PL011_LCRH_WLEN_8 \| UART_PL011_LCRH_FEN;
	writel(lcr, &regs->pl011_lcrh);
	return 0;
	}

	static int pl01x_generic_setbrg(struct pl01x_regs *regs, enum pl01x_type type,
	int clock, int baudrate)
	{
	switch (type) {
	case TYPE_PL010: {
	unsigned int divisor;

	/* disable everything */
	writel(0, &regs->pl010_cr);

	switch (baudrate) {
	case 9600:
	divisor = UART_PL010_BAUD_9600;
	break;
	case 19200:
	divisor = UART_PL010_BAUD_19200;
	break;
	case 38400:
	divisor = UART_PL010_BAUD_38400;
	break;
	case 57600:
	divisor = UART_PL010_BAUD_57600;
	break;
	case 115200:
	divisor = UART_PL010_BAUD_115200;
	break;
	default:
	divisor = UART_PL010_BAUD_38400;
	}

	writel((divisor & 0xf00) >> 8, &regs->pl010_lcrm);
	writel(divisor & 0xff, &regs->pl010_lcrl);

	/*
	* Set line control for the PL010 to be 8 bits, 1 stop bit,
	* no parity, fifo enabled
	*/
	writel(UART_PL010_LCRH_WLEN_8 \| UART_PL010_LCRH_FEN,
	&regs->pl010_lcrh);
	/* Finally, enable the UART */
	writel(UART_PL010_CR_UARTEN, &regs->pl010_cr);
	break;
	}
	case TYPE_PL011: {
	unsigned int temp;
	unsigned int divider;
	unsigned int remainder;
	unsigned int fraction;

	/* Without a valid clock rate we cannot set up the baudrate. */
	if (clock) {
	/*
	* Set baud rate
	*
	* IBRD = UART_CLK / (16 * BAUD_RATE)
	* FBRD = RND((64 * MOD(UART_CLK,(16 * BAUD_RATE)))
	* / (16 * BAUD_RATE))
	*/
	temp = 16 * baudrate;
	divider = clock / temp;
	remainder = clock % temp;
	temp = (8 * remainder) / baudrate;
	fraction = (temp >> 1) + (temp & 1);

	writel(divider, &regs->pl011_ibrd);
	writel(fraction, &regs->pl011_fbrd);
	}

	pl011_set_line_control(regs);
	/* Finally, enable the UART */
	writel(UART_PL011_CR_UARTEN \| UART_PL011_CR_TXE \|
	UART_PL011_CR_RXE \| UART_PL011_CR_RTS, &regs->pl011_cr);
	break;
	}
	default:
	return -EINVAL;
	}

	return 0;
	}

	#if !CONFIG_IS_ENABLED(DM_SERIAL)
	static void pl01x_serial_init_baud(int baudrate)
	{
	int clock = 0;

	#if defined(CONFIG_PL011_SERIAL)
	pl01x_type = TYPE_PL011;
	clock = CFG_PL011_CLOCK;
	#endif
	base_regs = (struct pl01x_regs *)port[CONFIG_CONS_INDEX];

	pl01x_generic_serial_init(base_regs, pl01x_type);
	pl01x_generic_setbrg(base_regs, pl01x_type, clock, baudrate);
	}

	/*
	* Integrator AP has two UARTs, we use the first one, at 38400-8-N-1
	* Integrator CP has two UARTs, use the first one, at 38400-8-N-1
	* Versatile PB has four UARTs.
	*/
	int pl01x_serial_init(void)
	{
	pl01x_serial_init_baud(CONFIG_BAUDRATE);

	return 0;
	}

	static void pl01x_serial_putc(const char c)
	{
	if (c == '\n')
	while (pl01x_putc(base_regs, '\r') == -EAGAIN);

	while (pl01x_putc(base_regs, c) == -EAGAIN);
	}

	static int pl01x_serial_getc(void)
	{
	while (1) {
	int ch = pl01x_getc(base_regs);

	if (ch == -EAGAIN) {
	schedule();
	continue;
	}

	return ch;
	}
	}

	static int pl01x_serial_tstc(void)
	{
	return pl01x_tstc(base_regs);
	}

	static void pl01x_serial_setbrg(void)
	{
	/*
	* Flush FIFO and wait for non-busy before changing baudrate to avoid
	* crap in console
	*/
	while (!(readl(&base_regs->fr) & UART_PL01x_FR_TXFE))
	schedule();
	while (readl(&base_regs->fr) & UART_PL01x_FR_BUSY)
	schedule();
	pl01x_serial_init_baud(gd->baudrate);
	}

	static struct serial_device pl01x_serial_drv = {
	.name = "pl01x_serial",
	.start = pl01x_serial_init,
	.stop = NULL,
	.setbrg = pl01x_serial_setbrg,
	.putc = pl01x_serial_putc,
	.puts = default_serial_puts,
	.getc = pl01x_serial_getc,
	.tstc = pl01x_serial_tstc,
	};

	void pl01x_serial_initialize(void)
	{
	serial_register(&pl01x_serial_drv);
	}

	__weak struct serial_device *default_serial_console(void)
	{
	return &pl01x_serial_drv;
	}
	#else

	static int pl01x_serial_getinfo(struct udevice *dev,
	struct serial_device_info *info)
	{
	struct pl01x_serial_plat *plat = dev_get_plat(dev);

	/* save code size */
	if (!not_xpl())
	return -ENOSYS;

	info->type = SERIAL_CHIP_PL01X;
	info->addr_space = SERIAL_ADDRESS_SPACE_MEMORY;
	info->addr = plat->base;
	info->size = 0x1000;
	info->reg_width = 4;
	info->reg_shift = 2;
	info->reg_offset = 0;
	info->clock = plat->clock;

	return 0;
	}

	int pl01x_serial_setbrg(struct udevice *dev, int baudrate)
	{
	struct pl01x_serial_plat *plat = dev_get_plat(dev);
	struct pl01x_priv *priv = dev_get_priv(dev);

	if (!plat->skip_init) {
	pl01x_generic_setbrg(priv->regs, priv->type, plat->clock,
	baudrate);
	}

	return 0;
	}

	int pl01x_serial_probe(struct udevice *dev)
	{
	struct pl01x_serial_plat *plat = dev_get_plat(dev);
	struct pl01x_priv *priv = dev_get_priv(dev);
	int ret;

	#if CONFIG_IS_ENABLED(OF_PLATDATA)
	struct dtd_serial_pl01x *dtplat = &plat->dtplat;

	priv->regs = (struct pl01x_regs *)dtplat->reg[0];
	plat->type = dtplat->type;
	#else
	priv->regs = (struct pl01x_regs *)plat->base;
	#endif
	priv->type = plat->type;

	if (!plat->skip_init) {
	ret = pl01x_generic_serial_init(priv->regs, priv->type);
	if (ret)
	return ret;
	return pl01x_serial_setbrg(dev, gd->baudrate);
	} else {
	return 0;
	}
	}

	int pl01x_serial_getc(struct udevice *dev)
	{
	struct pl01x_priv *priv = dev_get_priv(dev);

	return pl01x_getc(priv->regs);
	}

	int pl01x_serial_putc(struct udevice *dev, const char ch)
	{
	struct pl01x_priv *priv = dev_get_priv(dev);

	return pl01x_putc(priv->regs, ch);
	}

	int pl01x_serial_pending(struct udevice *dev, bool input)
	{
	struct pl01x_priv *priv = dev_get_priv(dev);
	unsigned int fr = readl(&priv->regs->fr);

	if (input)
	return pl01x_tstc(priv->regs);
	else
	return fr & UART_PL01x_FR_TXFE ? 0 : 1;
	}

	static const struct dm_serial_ops pl01x_serial_ops = {
	.putc = pl01x_serial_putc,
	.pending = pl01x_serial_pending,
	.getc = pl01x_serial_getc,
	.setbrg = pl01x_serial_setbrg,
	.getinfo = pl01x_serial_getinfo,
	};

	#if CONFIG_IS_ENABLED(OF_REAL)
	static const struct udevice_id pl01x_serial_id[] ={
	{.compatible = "arm,pl011", .data = TYPE_PL011},
	{.compatible = "arm,pl010", .data = TYPE_PL010},
	{}
	};

	#ifndef CFG_PL011_CLOCK
	#define CFG_PL011_CLOCK 0
	#endif

	int pl01x_serial_of_to_plat(struct udevice *dev)
	{
	struct pl01x_serial_plat *plat = dev_get_plat(dev);
	struct clk clk;
	fdt_addr_t addr;
	int ret;

	addr = dev_read_addr(dev);
	if (addr == FDT_ADDR_T_NONE)
	return -EINVAL;

	plat->base = addr;
	plat->clock = dev_read_u32_default(dev, "clock", CFG_PL011_CLOCK);
	ret = clk_get_by_index(dev, 0, &clk);
	if (!ret) {
	ret = clk_enable(&clk);
	if (ret && ret != -ENOSYS) {
	dev_err(dev, "failed to enable clock\n");
	return ret;
	}

	plat->clock = clk_get_rate(&clk);
	if (IS_ERR_VALUE(plat->clock)) {
	dev_err(dev, "failed to get rate\n");
	return plat->clock;
	}
	debug("%s: CLK %d\n", __func__, plat->clock);
	}
	plat->type = dev_get_driver_data(dev);
	plat->skip_init = dev_read_bool(dev, "skip-init");

	return 0;
	}
	#endif

	U_BOOT_DRIVER(serial_pl01x) = {
	.name = "serial_pl01x",
	.id = UCLASS_SERIAL,
	#if CONFIG_IS_ENABLED(OF_REAL)
	.of_match = of_match_ptr(pl01x_serial_id),
	.of_to_plat = of_match_ptr(pl01x_serial_of_to_plat),
	#endif
	.plat_auto = sizeof(struct pl01x_serial_plat),
	.probe = pl01x_serial_probe,
	.ops = &pl01x_serial_ops,
	.flags = DM_FLAG_PRE_RELOC,
	.priv_auto = sizeof(struct pl01x_priv),
	};

	DM_DRIVER_ALIAS(serial_pl01x, arm_pl011)
	DM_DRIVER_ALIAS(serial_pl01x, arm_pl010)
	#endif

	#if defined(CONFIG_DEBUG_UART_PL010) \|\| defined(CONFIG_DEBUG_UART_PL011)

	#include <debug_uart.h>

	static void _debug_uart_init(void)
	{
	#ifndef CONFIG_DEBUG_UART_SKIP_INIT
	struct pl01x_regs regs = (struct pl01x_regs )CONFIG_VAL(DEBUG_UART_BASE);
	enum pl01x_type type;

	if (IS_ENABLED(CONFIG_DEBUG_UART_PL011))
	type = TYPE_PL011;
	else
	type = TYPE_PL010;

	pl01x_generic_serial_init(regs, type);
	pl01x_generic_setbrg(regs, type,
	CONFIG_DEBUG_UART_CLOCK, CONFIG_BAUDRATE);
	#endif
	}

	static inline void _debug_uart_putc(int ch)
	{
	struct pl01x_regs regs = (struct pl01x_regs )CONFIG_VAL(DEBUG_UART_BASE);

	while (pl01x_putc(regs, ch) == -EAGAIN)
	;
	}

	DEBUG_UART_FUNCS

	#endif