| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Copyright 2017, 2019-2021 NXP |
| * Copyright 2015 Freescale Semiconductor |
| */ |
| |
| #ifndef __LS2_QDS_H |
| #define __LS2_QDS_H |
| |
| #include "ls2080a_common.h" |
| |
| #ifndef __ASSEMBLY__ |
| unsigned long get_board_sys_clk(void); |
| unsigned long get_board_ddr_clk(void); |
| #endif |
| |
| #ifdef CONFIG_FSL_QSPI |
| #define CONFIG_QIXIS_I2C_ACCESS |
| #define CONFIG_SYS_I2C_IFDR_DIV 0x7e |
| #endif |
| |
| #define CONFIG_SYS_I2C_FPGA_ADDR 0x66 |
| #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() |
| #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() |
| #define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4) |
| |
| #define CONFIG_DDR_SPD |
| #define CONFIG_DDR_ECC |
| #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER |
| #define CONFIG_MEM_INIT_VALUE 0xdeadbeef |
| #define SPD_EEPROM_ADDRESS1 0x51 |
| #define SPD_EEPROM_ADDRESS2 0x52 |
| #define SPD_EEPROM_ADDRESS3 0x53 |
| #define SPD_EEPROM_ADDRESS4 0x54 |
| #define SPD_EEPROM_ADDRESS5 0x55 |
| #define SPD_EEPROM_ADDRESS6 0x56 /* dummy address */ |
| #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 |
| #define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */ |
| #define CONFIG_DIMM_SLOTS_PER_CTLR 2 |
| #define CONFIG_CHIP_SELECTS_PER_CTRL 4 |
| #ifdef CONFIG_SYS_FSL_HAS_DP_DDR |
| #define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1 |
| #endif |
| |
| /* SATA */ |
| #define CONFIG_SCSI_AHCI_PLAT |
| |
| #define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1 |
| #define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2 |
| |
| #define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 |
| #define CONFIG_SYS_SCSI_MAX_LUN 1 |
| #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ |
| CONFIG_SYS_SCSI_MAX_LUN) |
| |
| #define CONFIG_SYS_NOR0_CSPR_EXT (0x0) |
| #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) |
| #define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(64*1024*1024) |
| |
| #define CONFIG_SYS_NOR0_CSPR \ |
| (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CONFIG_SYS_NOR0_CSPR_EARLY \ |
| (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CONFIG_SYS_NOR1_CSPR \ |
| (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH1_BASE_PHYS) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CONFIG_SYS_NOR1_CSPR_EARLY \ |
| (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH1_BASE_PHYS_EARLY) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12) |
| #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ |
| FTIM0_NOR_TEADC(0x5) | \ |
| FTIM0_NOR_TEAHC(0x5)) |
| #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ |
| FTIM1_NOR_TRAD_NOR(0x1a) |\ |
| FTIM1_NOR_TSEQRAD_NOR(0x13)) |
| #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ |
| FTIM2_NOR_TCH(0x4) | \ |
| FTIM2_NOR_TWPH(0x0E) | \ |
| FTIM2_NOR_TWP(0x1c)) |
| #define CONFIG_SYS_NOR_FTIM3 0x04000000 |
| #define CONFIG_SYS_IFC_CCR 0x01000000 |
| |
| #ifdef CONFIG_MTD_NOR_FLASH |
| #define CONFIG_SYS_FLASH_QUIET_TEST |
| #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\ |
| CONFIG_SYS_FLASH_BASE + 0x40000000} |
| #endif |
| |
| #define CONFIG_NAND_FSL_IFC |
| #define CONFIG_SYS_NAND_MAX_ECCPOS 256 |
| #define CONFIG_SYS_NAND_MAX_OOBFREE 2 |
| |
| #define CONFIG_SYS_NAND_CSPR_EXT (0x0) |
| #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ |
| | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ |
| | CSPR_MSEL_NAND /* MSEL = NAND */ \ |
| | CSPR_V) |
| #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) |
| |
| #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ |
| | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ |
| | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ |
| | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \ |
| | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ |
| | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \ |
| | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ |
| |
| #define CONFIG_SYS_NAND_ONFI_DETECTION |
| |
| /* ONFI NAND Flash mode0 Timing Params */ |
| #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ |
| FTIM0_NAND_TWP(0x18) | \ |
| FTIM0_NAND_TWCHT(0x07) | \ |
| FTIM0_NAND_TWH(0x0a)) |
| #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ |
| FTIM1_NAND_TWBE(0x39) | \ |
| FTIM1_NAND_TRR(0x0e) | \ |
| FTIM1_NAND_TRP(0x18)) |
| #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ |
| FTIM2_NAND_TREH(0x0a) | \ |
| FTIM2_NAND_TWHRE(0x1e)) |
| #define CONFIG_SYS_NAND_FTIM3 0x0 |
| |
| #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_MTD_NAND_VERIFY_WRITE |
| |
| #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) |
| |
| #define CONFIG_FSL_QIXIS /* use common QIXIS code */ |
| #define QIXIS_LBMAP_SWITCH 0x06 |
| #define QIXIS_LBMAP_MASK 0x0f |
| #define QIXIS_LBMAP_SHIFT 0 |
| #define QIXIS_LBMAP_DFLTBANK 0x00 |
| #define QIXIS_LBMAP_ALTBANK 0x04 |
| #define QIXIS_LBMAP_NAND 0x09 |
| #define QIXIS_LBMAP_SD 0x00 |
| #define QIXIS_LBMAP_QSPI 0x0f |
| #define QIXIS_RST_CTL_RESET 0x31 |
| #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 |
| #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 |
| #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 |
| #define QIXIS_RCW_SRC_NAND 0x107 |
| #define QIXIS_RCW_SRC_SD 0x40 |
| #define QIXIS_RCW_SRC_QSPI 0x62 |
| #define QIXIS_RST_FORCE_MEM 0x01 |
| |
| #define CONFIG_SYS_CSPR3_EXT (0x0) |
| #define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \ |
| | CSPR_PORT_SIZE_8 \ |
| | CSPR_MSEL_GPCM \ |
| | CSPR_V) |
| #define CONFIG_SYS_CSPR3_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ |
| | CSPR_PORT_SIZE_8 \ |
| | CSPR_MSEL_GPCM \ |
| | CSPR_V) |
| |
| #define CONFIG_SYS_AMASK3 IFC_AMASK(64*1024) |
| #define CONFIG_SYS_CSOR3 CSOR_GPCM_ADM_SHIFT(12) |
| /* QIXIS Timing parameters for IFC CS3 */ |
| #define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ |
| FTIM0_GPCM_TEADC(0x0e) | \ |
| FTIM0_GPCM_TEAHC(0x0e)) |
| #define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ |
| FTIM1_GPCM_TRAD(0x3f)) |
| #define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0xf) | \ |
| FTIM2_GPCM_TCH(0xf) | \ |
| FTIM2_GPCM_TWP(0x3E)) |
| #define CONFIG_SYS_CS3_FTIM3 0x0 |
| |
| #if defined(CONFIG_SPL) |
| #if defined(CONFIG_NAND_BOOT) |
| #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT |
| #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR_EARLY |
| #define CONFIG_SYS_CSPR1_FINAL CONFIG_SYS_NOR0_CSPR |
| #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT |
| #define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR1_CSPR_EARLY |
| #define CONFIG_SYS_CSPR2_FINAL CONFIG_SYS_NOR1_CSPR |
| #define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK_EARLY |
| #define CONFIG_SYS_AMASK2_FINAL CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT |
| #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR |
| #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK |
| #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR |
| #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 |
| #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 |
| #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 |
| #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 |
| |
| #define CONFIG_SPL_PAD_TO 0x20000 |
| #define CONFIG_SYS_NAND_U_BOOT_OFFS (256 * 1024) |
| #define CONFIG_SYS_NAND_U_BOOT_SIZE (640 * 1024) |
| #endif |
| #else |
| #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT |
| #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY |
| #define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR |
| #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT |
| #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR_EARLY |
| #define CONFIG_SYS_CSPR1_FINAL CONFIG_SYS_NOR1_CSPR |
| #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK_EARLY |
| #define CONFIG_SYS_AMASK1_FINAL CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT |
| #define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR |
| #define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK |
| #define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR |
| #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 |
| #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 |
| #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 |
| #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 |
| #endif |
| |
| /* Debug Server firmware */ |
| #define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR |
| #define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL |
| |
| #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000 |
| |
| /* |
| * I2C |
| */ |
| #define I2C_MUX_PCA_ADDR 0x77 |
| #define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/ |
| |
| /* I2C bus multiplexer */ |
| #define I2C_MUX_CH_DEFAULT 0x8 |
| |
| /* SPI */ |
| #ifdef CONFIG_FSL_DSPI |
| #define CONFIG_SPI_FLASH_STMICRO |
| #define CONFIG_SPI_FLASH_SST |
| #define CONFIG_SPI_FLASH_EON |
| #endif |
| |
| #ifdef CONFIG_FSL_QSPI |
| #define CONFIG_SPI_FLASH_SPANSION |
| #endif |
| /* |
| * Verify QSPI when boot from NAND, QIXIS brdcfg9 need configure. |
| * If boot from on-board NAND, ISO1 = 1, ISO2 = 0, IBOOT = 0 |
| * If boot from IFCCard NAND, ISO1 = 0, ISO2 = 0, IBOOT = 1 |
| */ |
| #define FSL_QIXIS_BRDCFG9_QSPI 0x1 |
| |
| /* |
| * MMC |
| */ |
| #ifdef CONFIG_MMC |
| #define CONFIG_ESDHC_DETECT_QUIRK ((readb(QIXIS_BASE + QIXIS_STAT_PRES1) & \ |
| QIXIS_SDID_MASK) != QIXIS_ESDHC_NO_ADAPTER) |
| #endif |
| |
| /* |
| * RTC configuration |
| */ |
| #define RTC |
| #define CONFIG_RTC_DS3231 1 |
| #define CONFIG_RTC_ENABLE_32KHZ_OUTPUT |
| #define CONFIG_SYS_I2C_RTC_ADDR 0x68 |
| #define CONFIG_RTC_ENABLE_32KHZ_OUTPUT |
| |
| /* EEPROM */ |
| #define CONFIG_SYS_I2C_EEPROM_NXID |
| #define CONFIG_SYS_EEPROM_BUS_NUM 0 |
| |
| #define CONFIG_FSL_MEMAC |
| |
| #ifdef CONFIG_PCI |
| #define CONFIG_PCI_SCAN_SHOW |
| #endif |
| |
| /* Initial environment variables */ |
| #undef CONFIG_EXTRA_ENV_SETTINGS |
| #ifdef CONFIG_NXP_ESBC |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "hwconfig=fsl_ddr:bank_intlv=auto\0" \ |
| "loadaddr=0x80100000\0" \ |
| "kernel_addr=0x100000\0" \ |
| "ramdisk_addr=0x800000\0" \ |
| "ramdisk_size=0x2000000\0" \ |
| "fdt_high=0xa0000000\0" \ |
| "initrd_high=0xffffffffffffffff\0" \ |
| "kernel_start=0x581000000\0" \ |
| "kernel_load=0xa0000000\0" \ |
| "kernel_size=0x2800000\0" \ |
| "mcmemsize=0x40000000\0" \ |
| "mcinitcmd=esbc_validate 0x580640000;" \ |
| "esbc_validate 0x580680000;" \ |
| "fsl_mc start mc 0x580a00000" \ |
| " 0x580e00000 \0" |
| #else |
| #ifdef CONFIG_TFABOOT |
| #define SD_MC_INIT_CMD \ |
| "mmcinfo;mmc read 0x80a00000 0x5000 0x1000;" \ |
| "mmc read 0x80e00000 0x7000 0x800;" \ |
| "fsl_mc start mc 0x80a00000 0x80e00000\0" |
| #define IFC_MC_INIT_CMD \ |
| "fsl_mc start mc 0x580a00000" \ |
| " 0x580e00000 \0" |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "hwconfig=fsl_ddr:bank_intlv=auto\0" \ |
| "loadaddr=0x80100000\0" \ |
| "loadaddr_sd=0x90100000\0" \ |
| "kernel_addr=0x581000000\0" \ |
| "kernel_addr_sd=0x8000\0" \ |
| "ramdisk_addr=0x800000\0" \ |
| "ramdisk_size=0x2000000\0" \ |
| "fdt_high=0xa0000000\0" \ |
| "initrd_high=0xffffffffffffffff\0" \ |
| "kernel_start=0x581000000\0" \ |
| "kernel_start_sd=0x8000\0" \ |
| "kernel_load=0xa0000000\0" \ |
| "kernel_size=0x2800000\0" \ |
| "kernel_size_sd=0x14000\0" \ |
| "load_addr=0xa0000000\0" \ |
| "kernelheader_addr=0x580600000\0" \ |
| "kernelheader_addr_r=0x80200000\0" \ |
| "kernelheader_size=0x40000\0" \ |
| "BOARD=ls2088aqds\0" \ |
| "mcmemsize=0x70000000 \0" \ |
| "scriptaddr=0x80000000\0" \ |
| "scripthdraddr=0x80080000\0" \ |
| IFC_MC_INIT_CMD \ |
| BOOTENV \ |
| "boot_scripts=ls2088aqds_boot.scr\0" \ |
| "boot_script_hdr=hdr_ls2088aqds_bs.out\0" \ |
| "scan_dev_for_boot_part=" \ |
| "part list ${devtype} ${devnum} devplist; " \ |
| "env exists devplist || setenv devplist 1; " \ |
| "for distro_bootpart in ${devplist}; do " \ |
| "if fstype ${devtype} " \ |
| "${devnum}:${distro_bootpart} " \ |
| "bootfstype; then " \ |
| "run scan_dev_for_boot; " \ |
| "fi; " \ |
| "done\0" \ |
| "boot_a_script=" \ |
| "load ${devtype} ${devnum}:${distro_bootpart} " \ |
| "${scriptaddr} ${prefix}${script}; " \ |
| "env exists secureboot && load ${devtype} " \ |
| "${devnum}:${distro_bootpart} " \ |
| "${scripthdraddr} ${prefix}${boot_script_hdr} " \ |
| "&& esbc_validate ${scripthdraddr};" \ |
| "source ${scriptaddr}\0" \ |
| "nor_bootcmd=echo Trying load from nor..;" \ |
| "cp.b $kernel_addr $load_addr " \ |
| "$kernel_size ; env exists secureboot && " \ |
| "cp.b $kernelheader_addr $kernelheader_addr_r " \ |
| "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\ |
| "bootm $load_addr#$BOARD\0" \ |
| "sd_bootcmd=echo Trying load from SD ..;" \ |
| "mmcinfo; mmc read $load_addr " \ |
| "$kernel_addr_sd $kernel_size_sd && " \ |
| "bootm $load_addr#$BOARD\0" |
| #elif defined(CONFIG_SD_BOOT) |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "hwconfig=fsl_ddr:bank_intlv=auto\0" \ |
| "loadaddr=0x90100000\0" \ |
| "kernel_addr=0x800\0" \ |
| "ramdisk_addr=0x800000\0" \ |
| "ramdisk_size=0x2000000\0" \ |
| "fdt_high=0xa0000000\0" \ |
| "initrd_high=0xffffffffffffffff\0" \ |
| "kernel_start=0x8000\0" \ |
| "kernel_load=0xa0000000\0" \ |
| "kernel_size=0x14000\0" \ |
| "mcinitcmd=mmcinfo;mmc read 0x80a00000 0x5000 0x1000;" \ |
| "mmc read 0x80e00000 0x7000 0x800;" \ |
| "fsl_mc start mc 0x80a00000 0x80e00000\0" \ |
| "mcmemsize=0x70000000 \0" |
| #else |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "hwconfig=fsl_ddr:bank_intlv=auto\0" \ |
| "loadaddr=0x80100000\0" \ |
| "kernel_addr=0x100000\0" \ |
| "ramdisk_addr=0x800000\0" \ |
| "ramdisk_size=0x2000000\0" \ |
| "fdt_high=0xa0000000\0" \ |
| "initrd_high=0xffffffffffffffff\0" \ |
| "kernel_start=0x581000000\0" \ |
| "kernel_load=0xa0000000\0" \ |
| "kernel_size=0x2800000\0" \ |
| "mcmemsize=0x40000000\0" \ |
| "mcinitcmd=fsl_mc start mc 0x580a00000" \ |
| " 0x580e00000 \0" |
| #endif /* CONFIG_TFABOOT */ |
| #endif /* CONFIG_NXP_ESBC */ |
| |
| #ifdef CONFIG_TFABOOT |
| #define BOOT_TARGET_DEVICES(func) \ |
| func(USB, usb, 0) \ |
| func(MMC, mmc, 0) \ |
| func(SCSI, scsi, 0) \ |
| func(DHCP, dhcp, na) |
| #include <config_distro_bootcmd.h> |
| |
| #define SD_BOOTCOMMAND \ |
| "env exists mcinitcmd && env exists secureboot "\ |
| "&& mmcinfo && mmc read $load_addr 0x3600 0x800 " \ |
| "&& esbc_validate $load_addr; " \ |
| "env exists mcinitcmd && run mcinitcmd " \ |
| "&& mmc read 0x80d00000 0x6800 0x800 " \ |
| "&& fsl_mc lazyapply dpl 0x80d00000; " \ |
| "run distro_bootcmd;run sd_bootcmd; " \ |
| "env exists secureboot && esbc_halt;" |
| |
| #define IFC_NOR_BOOTCOMMAND \ |
| "env exists mcinitcmd && env exists secureboot "\ |
| "&& esbc_validate 0x5806C0000; env exists mcinitcmd "\ |
| "&& fsl_mc lazyapply dpl 0x580d00000;" \ |
| "run distro_bootcmd;run nor_bootcmd; " \ |
| "env exists secureboot && esbc_halt;" |
| #endif |
| |
| #if defined(CONFIG_FSL_MC_ENET) && !defined(CONFIG_SPL_BUILD) |
| #define CONFIG_FSL_MEMAC |
| #define SGMII_CARD_PORT1_PHY_ADDR 0x1C |
| #define SGMII_CARD_PORT2_PHY_ADDR 0x1d |
| #define SGMII_CARD_PORT3_PHY_ADDR 0x1E |
| #define SGMII_CARD_PORT4_PHY_ADDR 0x1F |
| |
| #define XQSGMII_CARD_PHY1_PORT0_ADDR 0x0 |
| #define XQSGMII_CARD_PHY1_PORT1_ADDR 0x1 |
| #define XQSGMII_CARD_PHY1_PORT2_ADDR 0x2 |
| #define XQSGMII_CARD_PHY1_PORT3_ADDR 0x3 |
| #define XQSGMII_CARD_PHY2_PORT0_ADDR 0x4 |
| #define XQSGMII_CARD_PHY2_PORT1_ADDR 0x5 |
| #define XQSGMII_CARD_PHY2_PORT2_ADDR 0x6 |
| #define XQSGMII_CARD_PHY2_PORT3_ADDR 0x7 |
| #define XQSGMII_CARD_PHY3_PORT0_ADDR 0x8 |
| #define XQSGMII_CARD_PHY3_PORT1_ADDR 0x9 |
| #define XQSGMII_CARD_PHY3_PORT2_ADDR 0xa |
| #define XQSGMII_CARD_PHY3_PORT3_ADDR 0xb |
| #define XQSGMII_CARD_PHY4_PORT0_ADDR 0xc |
| #define XQSGMII_CARD_PHY4_PORT1_ADDR 0xd |
| #define XQSGMII_CARD_PHY4_PORT2_ADDR 0xe |
| #define XQSGMII_CARD_PHY4_PORT3_ADDR 0xf |
| |
| #define CONFIG_ETHPRIME "DPMAC1@xgmii" |
| |
| #endif |
| |
| #include <asm/fsl_secure_boot.h> |
| |
| #endif /* __LS2_QDS_H */ |