| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Copyright 2014 Freescale Semiconductor, Inc. |
| * Copyright 2020-2021 NXP |
| */ |
| |
| /* |
| * T4240 RDB board configuration file |
| */ |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #include <linux/stringify.h> |
| |
| #define CONFIG_FSL_SATA_V2 |
| #define CONFIG_PCIE4 |
| |
| #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ |
| |
| #ifdef CONFIG_RAMBOOT_PBL |
| #define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t4rdb/t4_pbi.cfg |
| #ifndef CONFIG_SDCARD |
| #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE |
| #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc |
| #else |
| #define CONFIG_SPL_FLUSH_IMAGE |
| #define CONFIG_SPL_PAD_TO 0x40000 |
| #define CONFIG_SPL_MAX_SIZE 0x28000 |
| #define RESET_VECTOR_OFFSET 0x27FFC |
| #define BOOT_PAGE_OFFSET 0x27000 |
| |
| #ifdef CONFIG_SDCARD |
| #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC |
| #define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) |
| #define CONFIG_SYS_MMC_U_BOOT_DST 0x00200000 |
| #define CONFIG_SYS_MMC_U_BOOT_START 0x00200000 |
| #define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10) |
| #ifndef CONFIG_SPL_BUILD |
| #define CONFIG_SYS_MPC85XX_NO_RESETVEC |
| #endif |
| #define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t4rdb/t4_sd_rcw.cfg |
| #endif |
| |
| #ifdef CONFIG_SPL_BUILD |
| #define CONFIG_SPL_SKIP_RELOCATE |
| #define CONFIG_SPL_COMMON_INIT_DDR |
| #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE |
| #endif |
| |
| #endif |
| #endif /* CONFIG_RAMBOOT_PBL */ |
| |
| #define CONFIG_DDR_ECC |
| |
| /* High Level Configuration Options */ |
| #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ |
| |
| #ifndef CONFIG_RESET_VECTOR_ADDRESS |
| #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc |
| #endif |
| |
| #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ |
| #define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS |
| #define CONFIG_PCIE1 /* PCIE controller 1 */ |
| #define CONFIG_PCIE2 /* PCIE controller 2 */ |
| #define CONFIG_PCIE3 /* PCIE controller 3 */ |
| #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ |
| |
| /* |
| * These can be toggled for performance analysis, otherwise use default. |
| */ |
| #define CONFIG_SYS_CACHE_STASHING |
| #define CONFIG_BTB /* toggle branch predition */ |
| #ifdef CONFIG_DDR_ECC |
| #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER |
| #define CONFIG_MEM_INIT_VALUE 0xdeadbeef |
| #endif |
| |
| #define CONFIG_ENABLE_36BIT_PHYS |
| |
| /* |
| * Config the L3 Cache as L3 SRAM |
| */ |
| #define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 |
| #define CONFIG_SYS_L3_SIZE (512 << 10) |
| #define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) |
| #define SPL_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) |
| #define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) |
| #define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10) |
| #define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) |
| |
| #define CONFIG_SYS_DCSRBAR 0xf0000000 |
| #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull |
| |
| /* |
| * DDR Setup |
| */ |
| #define CONFIG_VERY_BIG_RAM |
| #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE |
| |
| #define CONFIG_DIMM_SLOTS_PER_CTLR 1 |
| #define CONFIG_CHIP_SELECTS_PER_CTRL 4 |
| |
| #define CONFIG_DDR_SPD |
| |
| /* |
| * IFC Definitions |
| */ |
| #define CONFIG_SYS_FLASH_BASE 0xe0000000 |
| #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) |
| |
| #ifdef CONFIG_SPL_BUILD |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE |
| #else |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE |
| #endif |
| |
| #define CONFIG_HWCONFIG |
| |
| /* define to use L1 as initial stack */ |
| #define CONFIG_L1_INIT_RAM |
| #define CONFIG_SYS_INIT_RAM_LOCK |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000 |
| /* The assembler doesn't like typecast */ |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ |
| ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ |
| CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 |
| |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ |
| GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| #define CONFIG_SYS_MONITOR_LEN (768 * 1024) |
| #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) |
| |
| /* Serial Port - controlled on board with jumper J8 |
| * open - index 2 |
| * shorted - index 1 |
| */ |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) |
| #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) |
| #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) |
| |
| /* I2C */ |
| #if !CONFIG_IS_ENABLED(DM_I2C) |
| #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 |
| #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 |
| #else |
| #define CONFIG_I2C_SET_DEFAULT_BUS_NUM |
| #define CONFIG_I2C_DEFAULT_BUS_NUMBER 0 |
| #endif |
| |
| #define CONFIG_SYS_I2C_FSL |
| |
| /* |
| * General PCI |
| * Memory space is mapped 1-1, but I/O space must start from 0. |
| */ |
| |
| /* controller 1, direct to uli, tgtid 3, Base address 20000 */ |
| #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 |
| #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull |
| #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 |
| #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull |
| |
| /* controller 2, Slot 2, tgtid 2, Base address 201000 */ |
| #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 |
| #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull |
| #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 |
| #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull |
| |
| /* controller 3, Slot 1, tgtid 1, Base address 202000 */ |
| #define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000 |
| #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull |
| #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 |
| #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull |
| |
| /* controller 4, Base address 203000 */ |
| #define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 |
| #define CONFIG_SYS_PCIE4_MEM_PHYS 0xc60000000ull |
| #define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull |
| |
| #ifdef CONFIG_PCI |
| #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| #endif /* CONFIG_PCI */ |
| |
| /* SATA */ |
| #ifdef CONFIG_FSL_SATA_V2 |
| #define CONFIG_SYS_SATA_MAX_DEVICE 2 |
| #define CONFIG_SATA1 |
| #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR |
| #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA |
| #define CONFIG_SATA2 |
| #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR |
| #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA |
| |
| #define CONFIG_LBA48 |
| #endif |
| |
| #ifdef CONFIG_FMAN_ENET |
| #define CONFIG_ETHPRIME "FM1@DTSEC1" |
| #endif |
| |
| /* |
| * Environment |
| */ |
| #define CONFIG_LOADS_ECHO /* echo on for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 64 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ |
| #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ |
| |
| #ifdef CONFIG_CMD_KGDB |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ |
| #endif |
| |
| /* |
| * Environment Configuration |
| */ |
| #define CONFIG_ROOTPATH "/opt/nfsroot" |
| #define CONFIG_BOOTFILE "uImage" |
| #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/ |
| |
| /* default location for tftp and bootm */ |
| #define CONFIG_LOADADDR 1000000 |
| |
| #define CONFIG_HVBOOT \ |
| "setenv bootargs config-addr=0x60000000; " \ |
| "bootm 0x01000000 - 0x00f00000" |
| |
| #define CONFIG_SYS_CLK_FREQ 66666666 |
| #define CONFIG_DDR_CLK_FREQ 133333333 |
| |
| #ifndef __ASSEMBLY__ |
| unsigned long get_board_sys_clk(void); |
| unsigned long get_board_ddr_clk(void); |
| #endif |
| |
| /* |
| * DDR Setup |
| */ |
| #define CONFIG_SYS_SPD_BUS_NUM 0 |
| #define SPD_EEPROM_ADDRESS1 0x52 |
| #define SPD_EEPROM_ADDRESS2 0x54 |
| #define SPD_EEPROM_ADDRESS3 0x56 |
| #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 /* for p3041/p5010 */ |
| #define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ |
| |
| /* |
| * IFC Definitions |
| */ |
| #define CONFIG_SYS_NOR0_CSPR_EXT (0xf) |
| #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \ |
| + 0x8000000) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CONFIG_SYS_NOR1_CSPR_EXT (0xf) |
| #define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) |
| /* NOR Flash Timing Params */ |
| #define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 |
| |
| #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ |
| FTIM0_NOR_TEADC(0x5) | \ |
| FTIM0_NOR_TEAHC(0x5)) |
| #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ |
| FTIM1_NOR_TRAD_NOR(0x1A) |\ |
| FTIM1_NOR_TSEQRAD_NOR(0x13)) |
| #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ |
| FTIM2_NOR_TCH(0x4) | \ |
| FTIM2_NOR_TWPH(0x0E) | \ |
| FTIM2_NOR_TWP(0x1c)) |
| #define CONFIG_SYS_NOR_FTIM3 0x0 |
| |
| #define CONFIG_SYS_FLASH_QUIET_TEST |
| #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \ |
| + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} |
| |
| /* NAND Flash on IFC */ |
| #define CONFIG_NAND_FSL_IFC |
| #define CONFIG_SYS_NAND_MAX_ECCPOS 256 |
| #define CONFIG_SYS_NAND_MAX_OOBFREE 2 |
| #define CONFIG_SYS_NAND_BASE 0xff800000 |
| #define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) |
| |
| #define CONFIG_SYS_NAND_CSPR_EXT (0xf) |
| #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ |
| | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ |
| | CSPR_MSEL_NAND /* MSEL = NAND */ \ |
| | CSPR_V) |
| #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) |
| |
| #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ |
| | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ |
| | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ |
| | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ |
| | CSOR_NAND_PGS_4K /* Page Size = 4K */ \ |
| | CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \ |
| | CSOR_NAND_PB(128)) /*Page Per Block = 128*/ |
| |
| #define CONFIG_SYS_NAND_ONFI_DETECTION |
| |
| /* ONFI NAND Flash mode0 Timing Params */ |
| #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ |
| FTIM0_NAND_TWP(0x18) | \ |
| FTIM0_NAND_TWCHT(0x07) | \ |
| FTIM0_NAND_TWH(0x0a)) |
| #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ |
| FTIM1_NAND_TWBE(0x39) | \ |
| FTIM1_NAND_TRR(0x0e) | \ |
| FTIM1_NAND_TRP(0x18)) |
| #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ |
| FTIM2_NAND_TREH(0x0a) | \ |
| FTIM2_NAND_TWHRE(0x1e)) |
| #define CONFIG_SYS_NAND_FTIM3 0x0 |
| |
| #define CONFIG_SYS_NAND_DDR_LAW 11 |
| #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| |
| #define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) |
| |
| #if defined(CONFIG_MTD_RAW_NAND) |
| #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT |
| #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR |
| #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK |
| #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR |
| #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 |
| #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 |
| #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 |
| #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 |
| #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT |
| #define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR |
| #define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #else |
| #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT |
| #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR |
| #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT |
| #define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR |
| #define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK |
| #define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR |
| #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 |
| #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 |
| #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 |
| #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 |
| #endif |
| #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR1_CSPR_EXT |
| #define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR1_CSPR |
| #define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| |
| /* CPLD on IFC */ |
| #define CONFIG_SYS_CPLD_BASE 0xffdf0000 |
| #define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE) |
| #define CONFIG_SYS_CSPR3_EXT (0xf) |
| #define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \ |
| | CSPR_PORT_SIZE_8 \ |
| | CSPR_MSEL_GPCM \ |
| | CSPR_V) |
| |
| #define CONFIG_SYS_AMASK3 IFC_AMASK(64 * 1024) |
| #define CONFIG_SYS_CSOR3 0x0 |
| |
| /* CPLD Timing parameters for IFC CS3 */ |
| #define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ |
| FTIM0_GPCM_TEADC(0x0e) | \ |
| FTIM0_GPCM_TEAHC(0x0e)) |
| #define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ |
| FTIM1_GPCM_TRAD(0x1f)) |
| #define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ |
| FTIM2_GPCM_TCH(0x8) | \ |
| FTIM2_GPCM_TWP(0x1f)) |
| #define CONFIG_SYS_CS3_FTIM3 0x0 |
| |
| #if defined(CONFIG_RAMBOOT_PBL) |
| #define CONFIG_SYS_RAMBOOT |
| #endif |
| |
| /* I2C */ |
| #define CONFIG_SYS_FSL_I2C_SPEED 100000 /* I2C speed */ |
| #define CONFIG_SYS_FSL_I2C2_SPEED 100000 /* I2C2 speed */ |
| #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ |
| #define I2C_MUX_PCA_ADDR_SEC 0x76 /* I2C bus multiplexer,secondary */ |
| |
| #define I2C_MUX_CH_DEFAULT 0x8 |
| #define I2C_MUX_CH_VOL_MONITOR 0xa |
| #define I2C_MUX_CH_VSC3316_FS 0xc |
| #define I2C_MUX_CH_VSC3316_BS 0xd |
| |
| /* Voltage monitor on channel 2*/ |
| #define I2C_VOL_MONITOR_ADDR 0x40 |
| #define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 |
| #define I2C_VOL_MONITOR_BUS_V_OVF 0x1 |
| #define I2C_VOL_MONITOR_BUS_V_SHIFT 3 |
| |
| #define CONFIG_VID_FLS_ENV "t4240rdb_vdd_mv" |
| #ifndef CONFIG_SPL_BUILD |
| #define CONFIG_VID |
| #endif |
| #define CONFIG_VOL_MONITOR_IR36021_SET |
| #define CONFIG_VOL_MONITOR_IR36021_READ |
| /* The lowest and highest voltage allowed for T4240RDB */ |
| #define VDD_MV_MIN 819 |
| #define VDD_MV_MAX 1212 |
| |
| /* |
| * eSPI - Enhanced SPI |
| */ |
| |
| /* Qman/Bman */ |
| #ifndef CONFIG_NOBQFMAN |
| #define CONFIG_SYS_BMAN_NUM_PORTALS 50 |
| #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 |
| #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull |
| #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 |
| #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 |
| #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 |
| #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE |
| #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) |
| #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ |
| CONFIG_SYS_BMAN_CENA_SIZE) |
| #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) |
| #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 |
| #define CONFIG_SYS_QMAN_NUM_PORTALS 50 |
| #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 |
| #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull |
| #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 |
| #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 |
| #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 |
| #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE |
| #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) |
| #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ |
| CONFIG_SYS_QMAN_CENA_SIZE) |
| #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) |
| #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 |
| |
| #define CONFIG_SYS_DPAA_FMAN |
| #define CONFIG_SYS_DPAA_PME |
| #define CONFIG_SYS_PMAN |
| #define CONFIG_SYS_DPAA_DCE |
| #define CONFIG_SYS_DPAA_RMAN |
| #define CONFIG_SYS_INTERLAKEN |
| |
| /* Default address of microcode for the Linux Fman driver */ |
| #if defined(CONFIG_SPIFLASH) |
| /* |
| * env is stored at 0x100000, sector size is 0x10000, ucode is stored after |
| * env, so we got 0x110000. |
| */ |
| #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 |
| #elif defined(CONFIG_SDCARD) |
| /* |
| * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is |
| * about 1MB (2048 blocks), Env is stored after the image, and the env size is |
| * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080. |
| */ |
| #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) |
| #elif defined(CONFIG_MTD_RAW_NAND) |
| #define CONFIG_SYS_FMAN_FW_ADDR (8 * CONFIG_SYS_NAND_BLOCK_SIZE) |
| #else |
| #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 |
| #endif |
| #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 |
| #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) |
| #endif /* CONFIG_NOBQFMAN */ |
| |
| #ifdef CONFIG_SYS_DPAA_FMAN |
| #define SGMII_PHY_ADDR1 0x0 |
| #define SGMII_PHY_ADDR2 0x1 |
| #define SGMII_PHY_ADDR3 0x2 |
| #define SGMII_PHY_ADDR4 0x3 |
| #define SGMII_PHY_ADDR5 0x4 |
| #define SGMII_PHY_ADDR6 0x5 |
| #define SGMII_PHY_ADDR7 0x6 |
| #define SGMII_PHY_ADDR8 0x7 |
| #define FM1_10GEC1_PHY_ADDR 0x10 |
| #define FM1_10GEC2_PHY_ADDR 0x11 |
| #define FM2_10GEC1_PHY_ADDR 0x12 |
| #define FM2_10GEC2_PHY_ADDR 0x13 |
| #define CORTINA_PHY_ADDR1 FM1_10GEC1_PHY_ADDR |
| #define CORTINA_PHY_ADDR2 FM1_10GEC2_PHY_ADDR |
| #define CORTINA_PHY_ADDR3 FM2_10GEC1_PHY_ADDR |
| #define CORTINA_PHY_ADDR4 FM2_10GEC2_PHY_ADDR |
| #endif |
| |
| /* SATA */ |
| #ifdef CONFIG_FSL_SATA_V2 |
| #define CONFIG_SYS_SATA_MAX_DEVICE 2 |
| #define CONFIG_SATA1 |
| #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR |
| #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA |
| #define CONFIG_SATA2 |
| #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR |
| #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA |
| |
| #define CONFIG_LBA48 |
| #endif |
| |
| #ifdef CONFIG_FMAN_ENET |
| #define CONFIG_ETHPRIME "FM1@DTSEC1" |
| #endif |
| |
| /* |
| * USB |
| */ |
| #define CONFIG_USB_EHCI_FSL |
| #define CONFIG_EHCI_HCD_INIT_AFTER_RESET |
| #define CONFIG_HAS_FSL_DR_USB |
| |
| #ifdef CONFIG_MMC |
| #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR |
| #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT |
| #endif |
| |
| |
| #define __USB_PHY_TYPE utmi |
| |
| /* |
| * T4240 has 3 DDR controllers. Default to 3-way interleaving. It can be |
| * 3way_1KB, 3way_4KB, 3way_8KB. T4160 has 2 DDR controllers. Default to 2-way |
| * interleaving. It can be cacheline, page, bank, superbank. |
| * See doc/README.fsl-ddr for details. |
| */ |
| #ifdef CONFIG_ARCH_T4240 |
| #define CTRL_INTLV_PREFERED 3way_4KB |
| #else |
| #define CTRL_INTLV_PREFERED cacheline |
| #endif |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "hwconfig=fsl_ddr:" \ |
| "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ |
| "bank_intlv=auto;" \ |
| "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ |
| "netdev=eth0\0" \ |
| "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ |
| "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ |
| "tftpflash=tftpboot $loadaddr $uboot && " \ |
| "protect off $ubootaddr +$filesize && " \ |
| "erase $ubootaddr +$filesize && " \ |
| "cp.b $loadaddr $ubootaddr $filesize && " \ |
| "protect on $ubootaddr +$filesize && " \ |
| "cmp.b $loadaddr $ubootaddr $filesize\0" \ |
| "consoledev=ttyS0\0" \ |
| "ramdiskaddr=2000000\0" \ |
| "ramdiskfile=t4240rdb/ramdisk.uboot\0" \ |
| "fdtaddr=1e00000\0" \ |
| "fdtfile=t4240rdb/t4240rdb.dtb\0" \ |
| "bdev=sda3\0" |
| |
| #define CONFIG_HVBOOT \ |
| "setenv bootargs config-addr=0x60000000; " \ |
| "bootm 0x01000000 - 0x00f00000" |
| |
| #define CONFIG_LINUX \ |
| "setenv bootargs root=/dev/ram rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "setenv ramdiskaddr 0x02000000;" \ |
| "setenv fdtaddr 0x00c00000;" \ |
| "setenv loadaddr 0x1000000;" \ |
| "bootm $loadaddr $ramdiskaddr $fdtaddr" |
| |
| #define CONFIG_HDBOOT \ |
| "setenv bootargs root=/dev/$bdev rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr - $fdtaddr" |
| |
| #define CONFIG_NFSBOOTCOMMAND \ |
| "setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=$serverip:$rootpath " \ |
| "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr - $fdtaddr" |
| |
| #define CONFIG_RAMBOOTCOMMAND \ |
| "setenv bootargs root=/dev/ram rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $ramdiskaddr $ramdiskfile;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr $ramdiskaddr $fdtaddr" |
| |
| #define CONFIG_BOOTCOMMAND CONFIG_LINUX |
| |
| #include <asm/fsl_secure_boot.h> |
| |
| #endif /* __CONFIG_H */ |