Tegra30: Cardhu: Add pad config tables/code based on pinmux code
Pad config registers exist in APB_MISC_GP space, and control slew
rate, drive strengh, schmidt, high-speed, and low-power modes for
all of the pingroups in Tegra30. This builds off of the pinmux
way of constructing init tables to configure select pads (SDIOCFG,
for instance) during pinmux_init().
Currently, only SDIO1CFG is changed as per the TRM to work with
the SD-card slot on Cardhu.
Thanks to StephenW for the suggestion/original idea.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
diff --git a/arch/arm/include/asm/arch-tegra30/pinmux.h b/arch/arm/include/asm/arch-tegra30/pinmux.h
index 341951b..a9e1b46 100644
--- a/arch/arm/include/asm/arch-tegra30/pinmux.h
+++ b/arch/arm/include/asm/arch-tegra30/pinmux.h
@@ -1,5 +1,5 @@
/*
- * Copyright (c) 2010-2012, NVIDIA CORPORATION. All rights reserved.
+ * Copyright (c) 2010-2013, NVIDIA CORPORATION. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
@@ -531,6 +531,63 @@
PMUX_VDDIO_NONE
};
+#define PGRP_SLWF_NONE -1
+#define PGRP_SLWF_MAX 3
+#define PGRP_SLWR_NONE PGRP_SLWF_NONE
+#define PGRP_SLWR_MAX PGRP_SLWF_MAX
+
+#define PGRP_DRVUP_NONE -1
+#define PGRP_DRVUP_MAX 127
+#define PGRP_DRVDN_NONE PGRP_DRVUP_NONE
+#define PGRP_DRVDN_MAX PGRP_DRVUP_MAX
+
+/* return 1 if a padgrp is in range */
+#define pmux_padgrp_isvalid(pd) (((pd) >= 0) && ((pd) < PDRIVE_PINGROUP_COUNT))
+
+/* return 1 if a slew-rate rising/falling edge value is in range */
+#define pmux_pad_slw_isvalid(slw) (((slw) >= 0) && ((slw) <= PGRP_SLWF_MAX))
+
+/* return 1 if a driver output pull-up/down strength code value is in range */
+#define pmux_pad_drv_isvalid(drv) (((drv) >= 0) && ((drv) <= PGRP_DRVUP_MAX))
+
+/* return 1 if a low-power mode value is in range */
+#define pmux_pad_lpmd_isvalid(lpm) (((lpm) >= 0) && ((lpm) <= PGRP_LPMD_X))
+
+/* Defines a pin group cfg's low-power mode select */
+enum pgrp_lpmd {
+ PGRP_LPMD_X8 = 0,
+ PGRP_LPMD_X4,
+ PGRP_LPMD_X2,
+ PGRP_LPMD_X,
+ PGRP_LPMD_NONE = -1,
+};
+
+/* Defines whether a pin group cfg's schmidt is enabled or not */
+enum pgrp_schmt {
+ PGRP_SCHMT_DISABLE = 0,
+ PGRP_SCHMT_ENABLE = 1,
+};
+
+/* Defines whether a pin group cfg's high-speed mode is enabled or not */
+enum pgrp_hsm {
+ PGRP_HSM_DISABLE = 0,
+ PGRP_HSM_ENABLE = 1,
+};
+
+/*
+ * This defines the configuration for a pin group's pad control config
+ */
+struct padctrl_config {
+ enum pdrive_pingrp padgrp; /* pin group PDRIVE_PINGRP_x */
+ int slwf; /* falling edge slew */
+ int slwr; /* rising edge slew */
+ int drvup; /* pull-up drive strength */
+ int drvdn; /* pull-down drive strength */
+ enum pgrp_lpmd lpmd; /* low-power mode selection */
+ enum pgrp_schmt schmt; /* schmidt enable */
+ enum pgrp_hsm hsm; /* high-speed mode enable */
+};
+
/* t30 pin drive group and pin mux registers */
#define PDRIVE_PINGROUP_OFFSET (0x868 >> 2)
#define PMUX_OFFSET ((0x3000 >> 2) - PDRIVE_PINGROUP_OFFSET - \
@@ -600,4 +657,12 @@
/* Set a group of pins from a table */
void pinmux_init(void);
+/**
+ * Set the GP pad configs
+ *
+ * @param config List of config items
+ * @param len Number of config items in list
+ */
+void padgrp_config_table(struct padctrl_config *config, int len);
+
#endif /* _TEGRA30_PINMUX_H_ */