| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright 2019 NXP |
| */ |
| |
| #include <dt-bindings/usb/pd.h> |
| #include "imx8mn.dtsi" |
| |
| / { |
| chosen { |
| stdout-path = &uart2; |
| }; |
| |
| gpio-leds { |
| compatible = "gpio-leds"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_gpio_led>; |
| |
| status { |
| label = "yellow:status"; |
| gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>; |
| default-state = "on"; |
| }; |
| }; |
| |
| hdmi-connector { |
| compatible = "hdmi-connector"; |
| label = "hdmi"; |
| type = "a"; |
| |
| port { |
| hdmi_connector_in: endpoint { |
| remote-endpoint = <&adv7533_out>; |
| }; |
| }; |
| }; |
| |
| memory@40000000 { |
| device_type = "memory"; |
| reg = <0x0 0x40000000 0 0x80000000>; |
| }; |
| |
| reg_usdhc2_vmmc: regulator-usdhc2 { |
| compatible = "regulator-fixed"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>; |
| regulator-name = "VSD_3V3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; |
| off-on-delay-us = <12000>; |
| enable-active-high; |
| }; |
| |
| ir-receiver { |
| compatible = "gpio-ir-receiver"; |
| gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ir>; |
| linux,autosuspend-period = <125>; |
| }; |
| |
| audio_codec_bt_sco: audio-codec-bt-sco { |
| compatible = "linux,bt-sco"; |
| #sound-dai-cells = <1>; |
| }; |
| |
| wm8524: audio-codec { |
| #sound-dai-cells = <0>; |
| compatible = "wlf,wm8524"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_gpio_wlf>; |
| wlf,mute-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>; |
| }; |
| |
| sound-bt-sco { |
| compatible = "simple-audio-card"; |
| simple-audio-card,name = "bt-sco-audio"; |
| simple-audio-card,format = "dsp_a"; |
| simple-audio-card,bitclock-inversion; |
| simple-audio-card,frame-master = <&btcpu>; |
| simple-audio-card,bitclock-master = <&btcpu>; |
| |
| btcpu: simple-audio-card,cpu { |
| sound-dai = <&sai2>; |
| dai-tdm-slot-num = <2>; |
| dai-tdm-slot-width = <16>; |
| }; |
| |
| simple-audio-card,codec { |
| sound-dai = <&audio_codec_bt_sco 1>; |
| }; |
| }; |
| |
| sound-wm8524 { |
| compatible = "fsl,imx-audio-wm8524"; |
| model = "wm8524-audio"; |
| audio-cpu = <&sai3>; |
| audio-codec = <&wm8524>; |
| audio-asrc = <&easrc>; |
| audio-routing = |
| "Line Out Jack", "LINEVOUTL", |
| "Line Out Jack", "LINEVOUTR"; |
| }; |
| |
| sound-spdif { |
| compatible = "fsl,imx-audio-spdif"; |
| model = "imx-spdif"; |
| spdif-controller = <&spdif1>; |
| spdif-out; |
| spdif-in; |
| }; |
| |
| sound-micfil { |
| compatible = "fsl,imx-audio-card"; |
| model = "micfil-audio"; |
| |
| pri-dai-link { |
| link-name = "micfil hifi"; |
| format = "i2s"; |
| |
| cpu { |
| sound-dai = <&micfil>; |
| }; |
| }; |
| }; |
| }; |
| |
| &easrc { |
| fsl,asrc-rate = <48000>; |
| status = "okay"; |
| }; |
| |
| &fec1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_fec1>; |
| phy-mode = "rgmii-id"; |
| phy-handle = <ðphy0>; |
| fsl,magic-packet; |
| status = "okay"; |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ethphy0: ethernet-phy@0 { |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| reg = <0>; |
| reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>; |
| reset-assert-us = <10000>; |
| qca,disable-smarteee; |
| vddio-supply = <&vddio>; |
| |
| vddio: vddio-regulator { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| }; |
| }; |
| }; |
| |
| &flexspi { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexspi>; |
| status = "okay"; |
| |
| flash0: flash@0 { |
| compatible = "jedec,spi-nor"; |
| reg = <0>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| spi-max-frequency = <166000000>; |
| spi-tx-bus-width = <4>; |
| spi-rx-bus-width = <4>; |
| }; |
| }; |
| |
| &i2c1 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| status = "okay"; |
| }; |
| |
| &i2c2 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_i2c2>; |
| pinctrl-1 = <&pinctrl_i2c2_gpio>; |
| scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| status = "okay"; |
| |
| hdmi@3d { |
| compatible = "adi,adv7535"; |
| reg = <0x3d>, <0x3c>, <0x3e>, <0x3f>; |
| reg-names = "main", "cec", "edid", "packet"; |
| adi,dsi-lanes = <4>; |
| |
| adi,input-depth = <8>; |
| adi,input-colorspace = "rgb"; |
| adi,input-clock = "1x"; |
| adi,input-style = <1>; |
| adi,input-justification = "evenly"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| adv7533_in: endpoint { |
| remote-endpoint = <&dsi_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| adv7533_out: endpoint { |
| remote-endpoint = <&hdmi_connector_in>; |
| }; |
| }; |
| |
| }; |
| }; |
| |
| ptn5110: tcpc@50 { |
| compatible = "nxp,ptn5110"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_typec1>; |
| reg = <0x50>; |
| interrupt-parent = <&gpio2>; |
| interrupts = <11 IRQ_TYPE_LEVEL_LOW>; |
| status = "okay"; |
| |
| typec1_con: connector { |
| compatible = "usb-c-connector"; |
| label = "USB-C"; |
| power-role = "dual"; |
| data-role = "dual"; |
| try-power-role = "sink"; |
| source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>; |
| sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM) |
| PDO_VAR(5000, 20000, 3000)>; |
| op-sink-microwatt = <15000000>; |
| self-powered; |
| |
| port { |
| typec1_dr_sw: endpoint { |
| remote-endpoint = <&usb1_drd_sw>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c3 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_i2c3>; |
| pinctrl-1 = <&pinctrl_i2c3_gpio>; |
| scl-gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>; |
| sda-gpios = <&gpio5 19 GPIO_ACTIVE_HIGH>; |
| status = "okay"; |
| |
| pca6416: gpio@20 { |
| compatible = "ti,tca6416"; |
| reg = <0x20>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| camera@3c { |
| compatible = "ovti,ov5640"; |
| reg = <0x3c>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_camera>; |
| clocks = <&clk IMX8MN_CLK_CLKO1>; |
| clock-names = "xclk"; |
| assigned-clocks = <&clk IMX8MN_CLK_CLKO1>; |
| assigned-clock-parents = <&clk IMX8MN_CLK_24M>; |
| assigned-clock-rates = <24000000>; |
| powerdown-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; |
| reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; |
| |
| port { |
| ov5640_to_mipi_csi2: endpoint { |
| remote-endpoint = <&imx8mn_mipi_csi_in>; |
| clock-lanes = <0>; |
| data-lanes = <1 2>; |
| }; |
| }; |
| }; |
| }; |
| |
| &isi { |
| status = "okay"; |
| }; |
| |
| &micfil { |
| #sound-dai-cells = <0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pdm>; |
| assigned-clocks = <&clk IMX8MN_CLK_PDM>; |
| assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>; |
| assigned-clock-rates = <196608000>; |
| status = "okay"; |
| }; |
| |
| &mipi_csi { |
| status = "okay"; |
| |
| ports { |
| port@0 { |
| imx8mn_mipi_csi_in: endpoint { |
| remote-endpoint = <&ov5640_to_mipi_csi2>; |
| data-lanes = <1 2>; |
| }; |
| }; |
| }; |
| }; |
| |
| &lcdif { |
| status = "okay"; |
| }; |
| |
| &mipi_dsi { |
| samsung,esc-clock-frequency = <10000000>; |
| status = "okay"; |
| |
| ports { |
| port@1 { |
| reg = <1>; |
| |
| dsi_out: endpoint { |
| remote-endpoint = <&adv7533_in>; |
| data-lanes = <1 2 3 4>; |
| }; |
| }; |
| }; |
| }; |
| |
| &sai2 { |
| #sound-dai-cells = <0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_sai2>; |
| assigned-clocks = <&clk IMX8MN_CLK_SAI2>; |
| assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>; |
| assigned-clock-rates = <24576000>; |
| status = "okay"; |
| }; |
| |
| &sai3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_sai3>; |
| assigned-clocks = <&clk IMX8MN_CLK_SAI3>; |
| assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>; |
| assigned-clock-rates = <24576000>; |
| fsl,sai-mclk-direction-output; |
| status = "okay"; |
| }; |
| |
| &snvs_pwrkey { |
| status = "okay"; |
| }; |
| |
| &spdif1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_spdif1>; |
| assigned-clocks = <&clk IMX8MN_CLK_SPDIF1>; |
| assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>; |
| assigned-clock-rates = <24576000>; |
| status = "okay"; |
| }; |
| |
| &uart1 { /* BT */ |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart1>; |
| assigned-clocks = <&clk IMX8MN_CLK_UART1>; |
| assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_80M>; |
| uart-has-rtscts; |
| status = "okay"; |
| }; |
| |
| &uart2 { /* console */ |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| status = "okay"; |
| }; |
| |
| &uart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart3>; |
| assigned-clocks = <&clk IMX8MN_CLK_UART3>; |
| assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_80M>; |
| uart-has-rtscts; |
| status = "okay"; |
| }; |
| |
| &usbphynop1 { |
| wakeup-source; |
| }; |
| |
| &usbotg1 { |
| dr_mode = "otg"; |
| hnp-disable; |
| srp-disable; |
| adp-disable; |
| usb-role-switch; |
| disable-over-current; |
| samsung,picophy-pre-emp-curr-control = <3>; |
| samsung,picophy-dc-vol-level-adjust = <7>; |
| status = "okay"; |
| |
| port { |
| usb1_drd_sw: endpoint { |
| remote-endpoint = <&typec1_dr_sw>; |
| }; |
| }; |
| }; |
| |
| &usdhc2 { |
| assigned-clocks = <&clk IMX8MN_CLK_USDHC2>; |
| assigned-clock-rates = <200000000>; |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; |
| pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; |
| pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; |
| cd-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; |
| bus-width = <4>; |
| vmmc-supply = <®_usdhc2_vmmc>; |
| status = "okay"; |
| }; |
| |
| &usdhc3 { |
| assigned-clocks = <&clk IMX8MN_CLK_USDHC3_ROOT>; |
| assigned-clock-rates = <400000000>; |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc3>; |
| pinctrl-1 = <&pinctrl_usdhc3_100mhz>; |
| pinctrl-2 = <&pinctrl_usdhc3_200mhz>; |
| bus-width = <8>; |
| non-removable; |
| status = "okay"; |
| }; |
| |
| &wdog1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_wdog>; |
| fsl,ext-reset-output; |
| status = "okay"; |
| }; |
| |
| &iomuxc { |
| pinctrl_camera: cameragrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x19 |
| MX8MN_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19 |
| MX8MN_IOMUXC_GPIO1_IO14_CCMSRCGPCMIX_CLKO1 0x59 |
| >; |
| }; |
| |
| pinctrl_fec1: fec1grp { |
| fsl,pins = < |
| MX8MN_IOMUXC_ENET_MDC_ENET1_MDC 0x3 |
| MX8MN_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 |
| MX8MN_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f |
| MX8MN_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f |
| MX8MN_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f |
| MX8MN_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f |
| MX8MN_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 |
| MX8MN_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 |
| MX8MN_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 |
| MX8MN_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 |
| MX8MN_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f |
| MX8MN_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 |
| MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 |
| MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f |
| MX8MN_IOMUXC_SAI2_RXC_GPIO4_IO22 0x19 |
| >; |
| }; |
| |
| pinctrl_flexspi: flexspigrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x1c2 |
| MX8MN_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82 |
| MX8MN_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82 |
| MX8MN_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82 |
| MX8MN_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82 |
| MX8MN_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82 |
| >; |
| }; |
| |
| pinctrl_gpio_led: gpioledgrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19 |
| >; |
| }; |
| |
| pinctrl_gpio_wlf: gpiowlfgrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_I2C4_SDA_GPIO5_IO21 0xd6 |
| >; |
| }; |
| |
| pinctrl_ir: irgrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x4f |
| >; |
| }; |
| |
| pinctrl_i2c1: i2c1grp { |
| fsl,pins = < |
| MX8MN_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 |
| MX8MN_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 |
| >; |
| }; |
| |
| pinctrl_i2c2: i2c2grp { |
| fsl,pins = < |
| MX8MN_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3 |
| MX8MN_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3 |
| >; |
| }; |
| |
| pinctrl_i2c2_gpio: i2c2gpiogrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_I2C2_SCL_GPIO5_IO16 0x1c3 |
| MX8MN_IOMUXC_I2C2_SDA_GPIO5_IO17 0x1c3 |
| >; |
| }; |
| |
| pinctrl_i2c3: i2c3grp { |
| fsl,pins = < |
| MX8MN_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 |
| MX8MN_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 |
| >; |
| }; |
| |
| pinctrl_i2c3_gpio: i2c3gpiogrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_I2C3_SCL_GPIO5_IO18 0x1c3 |
| MX8MN_IOMUXC_I2C3_SDA_GPIO5_IO19 0x1c3 |
| >; |
| }; |
| |
| pinctrl_pdm: pdmgrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_SAI5_MCLK_SAI5_MCLK 0xd6 |
| MX8MN_IOMUXC_SAI5_RXC_PDM_CLK 0xd6 |
| MX8MN_IOMUXC_SAI5_RXFS_SAI5_RX_SYNC 0xd6 |
| MX8MN_IOMUXC_SAI5_RXD0_PDM_BIT_STREAM0 0xd6 |
| MX8MN_IOMUXC_SAI5_RXD1_PDM_BIT_STREAM1 0xd6 |
| MX8MN_IOMUXC_SAI5_RXD2_PDM_BIT_STREAM2 0xd6 |
| MX8MN_IOMUXC_SAI5_RXD3_PDM_BIT_STREAM3 0xd6 |
| >; |
| }; |
| |
| pinctrl_pmic: pmicirqgrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x141 |
| >; |
| }; |
| |
| pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41 |
| >; |
| }; |
| |
| pinctrl_sai2: sai2grp { |
| fsl,pins = < |
| MX8MN_IOMUXC_SAI2_TXC_SAI2_TX_BCLK 0xd6 |
| MX8MN_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC 0xd6 |
| MX8MN_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0 0xd6 |
| MX8MN_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0 0xd6 |
| >; |
| }; |
| |
| pinctrl_sai3: sai3grp { |
| fsl,pins = < |
| MX8MN_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0xd6 |
| MX8MN_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0xd6 |
| MX8MN_IOMUXC_SAI3_MCLK_SAI3_MCLK 0xd6 |
| MX8MN_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0xd6 |
| >; |
| }; |
| |
| pinctrl_spdif1: spdif1grp { |
| fsl,pins = < |
| MX8MN_IOMUXC_SPDIF_TX_SPDIF1_OUT 0xd6 |
| MX8MN_IOMUXC_SPDIF_RX_SPDIF1_IN 0xd6 |
| >; |
| }; |
| |
| pinctrl_typec1: typec1grp { |
| fsl,pins = < |
| MX8MN_IOMUXC_SD1_STROBE_GPIO2_IO11 0x159 |
| >; |
| }; |
| |
| pinctrl_uart1: uart1grp { |
| fsl,pins = < |
| MX8MN_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 |
| MX8MN_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 |
| MX8MN_IOMUXC_UART3_RXD_UART1_DCE_CTS_B 0x140 |
| MX8MN_IOMUXC_UART3_TXD_UART1_DCE_RTS_B 0x140 |
| >; |
| }; |
| |
| pinctrl_uart2: uart2grp { |
| fsl,pins = < |
| MX8MN_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140 |
| MX8MN_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140 |
| >; |
| }; |
| |
| pinctrl_uart3: uart3grp { |
| fsl,pins = < |
| MX8MN_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX 0x140 |
| MX8MN_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX 0x140 |
| MX8MN_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B 0x140 |
| MX8MN_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B 0x140 |
| >; |
| }; |
| |
| pinctrl_usdhc2_gpio: usdhc2gpiogrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x1c4 |
| >; |
| }; |
| |
| pinctrl_usdhc2: usdhc2grp { |
| fsl,pins = < |
| MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 |
| MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 |
| MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 |
| MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 |
| MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 |
| MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 |
| MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 |
| >; |
| }; |
| |
| pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 |
| MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 |
| MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 |
| MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 |
| MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 |
| MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 |
| MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 |
| >; |
| }; |
| |
| pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 |
| MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 |
| MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 |
| MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 |
| MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 |
| MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 |
| MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 |
| >; |
| }; |
| |
| pinctrl_usdhc3: usdhc3grp { |
| fsl,pins = < |
| MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x40000190 |
| MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0 |
| MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0 |
| MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0 |
| MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0 |
| MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0 |
| MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0 |
| MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0 |
| MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0 |
| MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0 |
| MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190 |
| >; |
| }; |
| |
| pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x40000194 |
| MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4 |
| MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4 |
| MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4 |
| MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4 |
| MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4 |
| MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4 |
| MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4 |
| MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4 |
| MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4 |
| MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194 |
| >; |
| }; |
| |
| pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x40000196 |
| MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6 |
| MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6 |
| MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6 |
| MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6 |
| MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6 |
| MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6 |
| MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6 |
| MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6 |
| MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6 |
| MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196 |
| >; |
| }; |
| |
| pinctrl_wdog: wdoggrp { |
| fsl,pins = < |
| MX8MN_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x166 |
| >; |
| }; |
| }; |