| // SPDX-License-Identifier: GPL-2.0 |
| #include "qcom-msm8974.dtsi" |
| #include "pm8841.dtsi" |
| #include "pm8941.dtsi" |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/leds/common.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| |
| / { |
| model = "LGE MSM 8974 HAMMERHEAD"; |
| compatible = "lge,hammerhead", "qcom,msm8974"; |
| chassis-type = "handset"; |
| |
| aliases { |
| serial0 = &blsp1_uart1; |
| serial1 = &blsp2_uart4; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gpio_keys_pin_a>; |
| |
| key-volume-up { |
| label = "volume_up"; |
| gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>; |
| linux,input-type = <1>; |
| linux,code = <KEY_VOLUMEUP>; |
| }; |
| |
| key-volume-down { |
| label = "volume_down"; |
| gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>; |
| linux,input-type = <1>; |
| linux,code = <KEY_VOLUMEDOWN>; |
| }; |
| }; |
| |
| clk_pwm: pwm { |
| compatible = "clk-pwm"; |
| clocks = <&mmcc CAMSS_GP1_CLK>; |
| |
| pinctrl-0 = <&vibrator_pin>; |
| pinctrl-names = "default"; |
| |
| #pwm-cells = <2>; |
| }; |
| |
| vibrator { |
| compatible = "pwm-vibrator"; |
| pwms = <&clk_pwm 0 100000>; |
| pwm-names = "enable"; |
| |
| vcc-supply = <&pm8941_l19>; |
| enable-gpios = <&tlmm 60 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| vreg_boost: vreg-boost { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "vreg-boost"; |
| regulator-min-microvolt = <3150000>; |
| regulator-max-microvolt = <3150000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| |
| gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&boost_bypass_n_pin>; |
| }; |
| |
| vreg_vph_pwr: vreg-vph-pwr { |
| compatible = "regulator-fixed"; |
| regulator-name = "vph-pwr"; |
| |
| regulator-min-microvolt = <3600000>; |
| regulator-max-microvolt = <3600000>; |
| |
| regulator-always-on; |
| }; |
| |
| vreg_wlan: wlan-regulator { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "wl-reg"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&tlmm 26 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wlan_regulator_pin>; |
| }; |
| }; |
| |
| &blsp1_i2c1 { |
| status = "okay"; |
| clock-frequency = <100000>; |
| |
| charger: bq24192@6b { |
| compatible = "ti,bq24192"; |
| reg = <0x6b>; |
| interrupts-extended = <&spmi_bus 0 0xd5 0 IRQ_TYPE_EDGE_FALLING>; |
| |
| omit-battery-class; |
| |
| usb_otg_vbus: usb-otg-vbus { }; |
| }; |
| |
| fuelgauge: max17048@36 { |
| compatible = "maxim,max17048"; |
| reg = <0x36>; |
| |
| maxim,double-soc; |
| maxim,rcomp = /bits/ 8 <0x4d>; |
| |
| interrupt-parent = <&tlmm>; |
| interrupts = <9 IRQ_TYPE_LEVEL_LOW>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&fuelgauge_pin>; |
| |
| maxim,alert-low-soc-level = <2>; |
| }; |
| }; |
| |
| &blsp1_i2c2 { |
| status = "okay"; |
| clock-frequency = <355000>; |
| |
| synaptics@70 { |
| compatible = "syna,rmi4-i2c"; |
| reg = <0x70>; |
| |
| interrupts-extended = <&tlmm 5 IRQ_TYPE_EDGE_FALLING>; |
| vdd-supply = <&pm8941_l22>; |
| vio-supply = <&pm8941_lvs3>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&touch_pin>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| rmi4-f01@1 { |
| reg = <0x1>; |
| syna,nosleep-mode = <1>; |
| }; |
| |
| rmi4-f12@12 { |
| reg = <0x12>; |
| syna,sensor-type = <1>; |
| }; |
| }; |
| }; |
| |
| &blsp1_i2c3 { |
| status = "okay"; |
| clock-frequency = <100000>; |
| |
| avago_apds993@39 { |
| compatible = "avago,apds9930"; |
| reg = <0x39>; |
| interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>; |
| vdd-supply = <&pm8941_l17>; |
| vddio-supply = <&pm8941_lvs1>; |
| led-max-microamp = <100000>; |
| amstaos,proximity-diodes = <0>; |
| }; |
| }; |
| |
| &blsp2_i2c5 { |
| status = "okay"; |
| clock-frequency = <355000>; |
| |
| backlight: led-controller@38 { |
| compatible = "ti,lm3630a"; |
| status = "okay"; |
| reg = <0x38>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| led@0 { |
| reg = <0>; |
| led-sources = <0 1>; |
| label = "lcd-backlight"; |
| default-brightness = <200>; |
| }; |
| }; |
| }; |
| |
| &blsp2_i2c6 { |
| status = "okay"; |
| clock-frequency = <100000>; |
| |
| mpu6515@68 { |
| compatible = "invensense,mpu6515"; |
| reg = <0x68>; |
| interrupts-extended = <&tlmm 73 IRQ_TYPE_EDGE_FALLING>; |
| vddio-supply = <&pm8941_lvs1>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mpu6515_pin>; |
| |
| mount-matrix = "0", "-1", "0", |
| "-1", "0", "0", |
| "0", "0", "1"; |
| |
| i2c-gate { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ak8963@f { |
| compatible = "asahi-kasei,ak8963"; |
| reg = <0x0f>; |
| gpios = <&tlmm 67 GPIO_ACTIVE_HIGH>; |
| vid-supply = <&pm8941_lvs1>; |
| vdd-supply = <&pm8941_l17>; |
| }; |
| |
| bmp280@76 { |
| compatible = "bosch,bmp280"; |
| reg = <0x76>; |
| vdda-supply = <&pm8941_lvs1>; |
| vddd-supply = <&pm8941_l17>; |
| }; |
| }; |
| }; |
| }; |
| |
| &blsp1_uart1 { |
| status = "okay"; |
| }; |
| |
| &blsp2_uart4 { |
| status = "okay"; |
| |
| bluetooth { |
| compatible = "brcm,bcm43438-bt"; |
| max-speed = <3000000>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&bt_pin>; |
| |
| host-wakeup-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>; |
| device-wakeup-gpios = <&tlmm 62 GPIO_ACTIVE_HIGH>; |
| shutdown-gpios = <&tlmm 41 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| &mdss { |
| status = "okay"; |
| }; |
| |
| &mdss_dsi0 { |
| status = "okay"; |
| |
| vdda-supply = <&pm8941_l2>; |
| vdd-supply = <&pm8941_lvs3>; |
| vddio-supply = <&pm8941_l12>; |
| |
| panel: panel@0 { |
| reg = <0>; |
| compatible = "lg,acx467akm-7"; |
| |
| backlight = <&backlight>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&panel_pin>; |
| |
| port { |
| panel_in: endpoint { |
| remote-endpoint = <&mdss_dsi0_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| &mdss_dsi0_out { |
| remote-endpoint = <&panel_in>; |
| data-lanes = <0 1 2 3>; |
| }; |
| |
| &mdss_dsi0_phy { |
| status = "okay"; |
| |
| vddio-supply = <&pm8941_l12>; |
| }; |
| |
| &pm8941_gpios { |
| gpio_keys_pin_a: gpio-keys-active-state { |
| pins = "gpio2", "gpio3"; |
| function = "normal"; |
| |
| bias-pull-up; |
| power-source = <PM8941_GPIO_S3>; |
| }; |
| |
| fuelgauge_pin: fuelgauge-int-state { |
| pins = "gpio9"; |
| function = "normal"; |
| |
| bias-disable; |
| input-enable; |
| power-source = <PM8941_GPIO_S3>; |
| }; |
| |
| wlan_sleep_clk_pin: wl-sleep-clk-state { |
| pins = "gpio16"; |
| function = "func2"; |
| |
| output-high; |
| power-source = <PM8941_GPIO_S3>; |
| }; |
| |
| wlan_regulator_pin: wl-reg-active-state { |
| pins = "gpio17"; |
| function = "normal"; |
| |
| bias-disable; |
| power-source = <PM8941_GPIO_S3>; |
| }; |
| |
| otg-hog { |
| gpio-hog; |
| gpios = <35 GPIO_ACTIVE_HIGH>; |
| output-high; |
| line-name = "otg-gpio"; |
| }; |
| }; |
| |
| &pm8941_lpg { |
| status = "okay"; |
| |
| qcom,power-source = <1>; |
| |
| multi-led { |
| color = <LED_COLOR_ID_RGB>; |
| function = LED_FUNCTION_STATUS; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| led@7 { |
| reg = <7>; |
| color = <LED_COLOR_ID_RED>; |
| }; |
| |
| led@6 { |
| reg = <6>; |
| color = <LED_COLOR_ID_GREEN>; |
| }; |
| |
| led@5 { |
| reg = <5>; |
| color = <LED_COLOR_ID_BLUE>; |
| }; |
| }; |
| }; |
| |
| &remoteproc_adsp { |
| cx-supply = <&pm8841_s2>; |
| status = "okay"; |
| }; |
| |
| &remoteproc_mss { |
| cx-supply = <&pm8841_s2>; |
| mss-supply = <&pm8841_s3>; |
| mx-supply = <&pm8841_s1>; |
| pll-supply = <&pm8941_l12>; |
| status = "okay"; |
| }; |
| |
| &rpm_requests { |
| regulators-0 { |
| compatible = "qcom,rpm-pm8841-regulators"; |
| |
| pm8841_s1: s1 { |
| regulator-min-microvolt = <675000>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| |
| pm8841_s2: s2 { |
| regulator-min-microvolt = <500000>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| |
| pm8841_s3: s3 { |
| regulator-min-microvolt = <1050000>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| |
| pm8841_s4: s4 { |
| regulator-min-microvolt = <815000>; |
| regulator-max-microvolt = <900000>; |
| }; |
| }; |
| |
| regulators-1 { |
| compatible = "qcom,rpm-pm8941-regulators"; |
| |
| vdd_l1_l3-supply = <&pm8941_s1>; |
| vdd_l2_lvs1_2_3-supply = <&pm8941_s3>; |
| vdd_l4_l11-supply = <&pm8941_s1>; |
| vdd_l5_l7-supply = <&pm8941_s2>; |
| vdd_l6_l12_l14_l15-supply = <&pm8941_s2>; |
| vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>; |
| vdd_l9_l10_l17_l22-supply = <&vreg_boost>; |
| vdd_l13_l20_l23_l24-supply = <&vreg_boost>; |
| vdd_l21-supply = <&vreg_boost>; |
| |
| pm8941_s1: s1 { |
| regulator-min-microvolt = <1300000>; |
| regulator-max-microvolt = <1300000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| pm8941_s2: s2 { |
| regulator-min-microvolt = <2150000>; |
| regulator-max-microvolt = <2150000>; |
| regulator-boot-on; |
| }; |
| |
| pm8941_s3: s3 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| pm8941_l1: l1 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| pm8941_l2: l2 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| pm8941_l3: l3 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| pm8941_l4: l4 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| pm8941_l5: l5 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pm8941_l6: l6 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| }; |
| |
| pm8941_l7: l7 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| }; |
| |
| pm8941_l8: l8 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pm8941_l9: l9 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| pm8941_l10: l10 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| pm8941_l11: l11 { |
| regulator-min-microvolt = <1300000>; |
| regulator-max-microvolt = <1300000>; |
| }; |
| |
| pm8941_l12: l12 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| pm8941_l13: l13 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-boot-on; |
| }; |
| |
| pm8941_l14: l14 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pm8941_l15: l15 { |
| regulator-min-microvolt = <2050000>; |
| regulator-max-microvolt = <2050000>; |
| }; |
| |
| pm8941_l16: l16 { |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <2700000>; |
| }; |
| |
| pm8941_l17: l17 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| |
| pm8941_l18: l18 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| |
| pm8941_l19: l19 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| pm8941_l20: l20 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-system-load = <200000>; |
| regulator-allow-set-load; |
| regulator-boot-on; |
| }; |
| |
| pm8941_l21: l21 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-boot-on; |
| }; |
| |
| pm8941_l22: l22 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| pm8941_l23: l23 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| }; |
| |
| pm8941_l24: l24 { |
| regulator-min-microvolt = <3075000>; |
| regulator-max-microvolt = <3075000>; |
| regulator-boot-on; |
| }; |
| |
| pm8941_lvs1: lvs1 {}; |
| pm8941_lvs3: lvs3 {}; |
| }; |
| }; |
| |
| &sdhc_1 { |
| status = "okay"; |
| |
| vmmc-supply = <&pm8941_l20>; |
| vqmmc-supply = <&pm8941_s3>; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc1_on>; |
| pinctrl-1 = <&sdc1_off>; |
| }; |
| |
| &sdhc_2 { |
| status = "okay"; |
| |
| max-frequency = <100000000>; |
| vmmc-supply = <&vreg_wlan>; |
| vqmmc-supply = <&pm8941_s3>; |
| non-removable; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc2_on>; |
| pinctrl-1 = <&sdc2_off>; |
| |
| bcrmf@1 { |
| compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac"; |
| reg = <1>; |
| |
| brcm,drive-strength = <10>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wlan_sleep_clk_pin>; |
| }; |
| }; |
| |
| &tlmm { |
| sdc1_on: sdc1-on-state { |
| clk-pins { |
| pins = "sdc1_clk"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| cmd-data-pins { |
| pins = "sdc1_cmd", "sdc1_data"; |
| drive-strength = <10>; |
| bias-pull-up; |
| }; |
| }; |
| |
| sdc2_on: sdc2-on-state { |
| clk-pins { |
| pins = "sdc2_clk"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| cmd-data-pins { |
| pins = "sdc2_cmd", "sdc2_data"; |
| drive-strength = <6>; |
| bias-pull-up; |
| }; |
| }; |
| |
| mpu6515_pin: mpu6515-state { |
| pins = "gpio73"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| |
| touch_pin: touch-state { |
| int-pins { |
| pins = "gpio5"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| reset-pins { |
| pins = "gpio8"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| panel_pin: panel-state { |
| pins = "gpio12"; |
| function = "mdp_vsync"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| bt_pin: bt-state { |
| hostwake-pins { |
| pins = "gpio42"; |
| function = "gpio"; |
| }; |
| |
| devwake-pins { |
| pins = "gpio62"; |
| function = "gpio"; |
| }; |
| |
| shutdown-pins { |
| pins = "gpio41"; |
| function = "gpio"; |
| }; |
| }; |
| |
| vibrator_pin: vibrator-state { |
| core-pins { |
| pins = "gpio27"; |
| function = "gp1_clk"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| enable-pins { |
| pins = "gpio60"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| }; |
| |
| &usb { |
| status = "okay"; |
| |
| phys = <&usb_hs1_phy>; |
| phy-select = <&tcsr 0xb000 0>; |
| |
| extcon = <&charger>, <&usb_id>; |
| vbus-supply = <&usb_otg_vbus>; |
| |
| hnp-disable; |
| srp-disable; |
| adp-disable; |
| }; |
| |
| &usb_hs1_phy { |
| status = "okay"; |
| |
| v1p8-supply = <&pm8941_l6>; |
| v3p3-supply = <&pm8941_l24>; |
| |
| qcom,init-seq = /bits/ 8 <0x1 0x64>; |
| }; |