| if ARCH_STM32MP |
| |
| config SPL |
| select SPL_CLK |
| select SPL_DM |
| select SPL_DM_SEQ_ALIAS |
| select SPL_DRIVERS_MISC_SUPPORT |
| select SPL_FRAMEWORK |
| select SPL_GPIO_SUPPORT |
| select SPL_LIBCOMMON_SUPPORT |
| select SPL_LIBGENERIC_SUPPORT |
| select SPL_OF_CONTROL |
| select SPL_OF_TRANSLATE |
| select SPL_PINCTRL |
| select SPL_REGMAP |
| select SPL_DM_RESET |
| select SPL_SERIAL_SUPPORT |
| select SPL_SPI_LOAD |
| select SPL_SYSCON |
| select SPL_WATCHDOG_SUPPORT if WATCHDOG |
| imply BOOTSTAGE_STASH if SPL_BOOTSTAGE |
| imply SPL_BOOTSTAGE if BOOTSTAGE |
| imply SPL_DISPLAY_PRINT |
| imply SPL_LIBDISK_SUPPORT |
| |
| config SYS_SOC |
| default "stm32mp" |
| |
| config SYS_MALLOC_LEN |
| default 0x2000000 |
| |
| config ENV_SIZE |
| default 0x2000 |
| |
| config STM32MP15x |
| bool "Support STMicroelectronics STM32MP15x Soc" |
| select ARCH_SUPPORT_PSCI if !TFABOOT |
| select ARM_SMCCC if TFABOOT |
| select CPU_V7A |
| select CPU_V7_HAS_NONSEC if !TFABOOT |
| select CPU_V7_HAS_VIRT |
| select OF_BOARD_SETUP |
| select PINCTRL_STM32 |
| select STM32_RCC |
| select STM32_RESET |
| select STM32_SERIAL |
| select SYS_ARCH_TIMER |
| imply CMD_NVEDIT_INFO |
| imply SYSRESET_PSCI if TFABOOT |
| imply SYSRESET_SYSCON if !TFABOOT |
| help |
| support of STMicroelectronics SOC STM32MP15x family |
| STM32MP157, STM32MP153 or STM32MP151 |
| STMicroelectronics MPU with core ARMv7 |
| dual core A7 for STM32MP157/3, monocore for STM32MP151 |
| target all the STMicroelectronics board with SOC STM32MP1 family |
| |
| choice |
| prompt "STM32MP15x board select" |
| optional |
| |
| config TARGET_ST_STM32MP15x |
| bool "STMicroelectronics STM32MP15x boards" |
| select STM32MP15x |
| imply BOOTCOUNT_LIMIT |
| imply BOOTSTAGE |
| imply CMD_BOOTCOUNT |
| imply CMD_BOOTSTAGE |
| imply CMD_CLS if CMD_BMP |
| imply DISABLE_CONSOLE |
| imply PRE_CONSOLE_BUFFER |
| imply SILENT_CONSOLE |
| help |
| target the STMicroelectronics board with SOC STM32MP15x |
| managed by board/st/stm32mp1: |
| Evalulation board (EV1) or Discovery board (DK1 and DK2). |
| The difference between board are managed with devicetree |
| |
| config TARGET_DH_STM32MP1_PDK2 |
| bool "DH STM32MP1 PDK2" |
| select STM32MP15x |
| imply BOOTCOUNT_LIMIT |
| imply CMD_BOOTCOUNT |
| help |
| Target the DH PDK2 development kit with STM32MP15x SoM. |
| |
| endchoice |
| |
| config SYS_TEXT_BASE |
| default 0xC0100000 |
| |
| config NR_DRAM_BANKS |
| default 1 |
| |
| config SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION_MMC2 |
| hex "Partition on MMC2 to use to load U-Boot from" |
| depends on SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION |
| default 1 |
| help |
| Partition on the second MMC to load U-Boot from when the MMC is being |
| used in raw mode |
| |
| config STM32_ETZPC |
| bool "STM32 Extended TrustZone Protection" |
| depends on STM32MP15x |
| default y |
| help |
| Say y to enable STM32 Extended TrustZone Protection |
| |
| config CMD_STM32PROG |
| bool "command stm32prog for STM32CudeProgrammer" |
| select DFU |
| select DFU_RAM |
| select DFU_VIRT |
| select PARTITION_TYPE_GUID |
| imply CMD_GPT if MMC |
| imply CMD_MTD if MTD |
| imply DFU_MMC if MMC |
| imply DFU_MTD if MTD |
| help |
| activate a specific command stm32prog for STM32MP soc family |
| witch update the device with the tools STM32CubeProgrammer, |
| using UART with STM32 protocol or USB with DFU protocol |
| NB: access to not volatile memory (NOR/NAND/SD/eMMC) is based |
| on U-Boot DFU framework |
| |
| config CMD_STM32KEY |
| bool "command stm32key to fuse public key hash" |
| default y |
| help |
| fuse public key hash in corresponding fuse used to authenticate |
| binary. |
| |
| config PRE_CON_BUF_ADDR |
| default 0xC02FF000 |
| |
| config PRE_CON_BUF_SZ |
| default 4096 |
| |
| config BOOTSTAGE_STASH_ADDR |
| default 0xC3000000 |
| |
| if BOOTCOUNT_LIMIT |
| config SYS_BOOTCOUNT_SINGLEWORD |
| default y |
| |
| # TAMP_BOOTCOUNT = TAMP_BACKUP_REGISTER(21) |
| config SYS_BOOTCOUNT_ADDR |
| default 0x5C00A154 |
| endif |
| |
| if DEBUG_UART |
| |
| config DEBUG_UART_BOARD_INIT |
| default y |
| |
| # debug on UART4 by default |
| config DEBUG_UART_BASE |
| default 0x40010000 |
| |
| # clock source is HSI on reset |
| config DEBUG_UART_CLOCK |
| default 64000000 |
| endif |
| |
| source "board/st/stm32mp1/Kconfig" |
| source "board/dhelectronics/dh_stm32mp1/Kconfig" |
| |
| endif |