| .. SPDX-License-Identifier: GPL-2.0+ |
| |
| StarFive VisionFive2 |
| ==================== |
| |
| JH7110 RISC-V SoC |
| --------------------- |
| The JH7110 is 4+1 64-bit RISC-V SoC from StarFive. |
| |
| The StarFive VisionFive2 development platform is based on JH7110 and capable |
| of running Linux. |
| |
| Mainline support |
| ---------------- |
| |
| The support for following drivers are already enabled: |
| |
| 1. ns16550 UART Driver. |
| 2. StarFive JH7110 clock Driver. |
| 3. StarFive JH7110 reset Driver. |
| 4. Cadence QSPI controller Driver. |
| 5. MMC SPI Driver for MMC/SD support. |
| |
| Booting from MMC using U-Boot SPL |
| --------------------------------- |
| |
| The current U-Boot port is supported in S-mode only and loaded from DRAM. |
| |
| A prior stage M-mode firmware/bootloader (e.g OpenSBI) is required to |
| boot the u-boot.itb in S-mode and provide M-mode runtime services. |
| |
| Currently, the u-boot.itb is used as a dynamic of the OpenSBI FW_DYNAMIC |
| firmware with the latest. |
| |
| Building |
| ~~~~~~~~ |
| |
| 1. Add the RISC-V toolchain to your PATH. |
| 2. Setup ARCH & cross compilation environment variable: |
| |
| .. code-block:: none |
| |
| export CROSS_COMPILE=<riscv64 toolchain prefix> |
| |
| Before building U-Boot SPL, OpenSBI must be built first. OpenSBI can be |
| cloned and built for JH7110 as below: |
| |
| .. code-block:: console |
| |
| git clone https://github.com/riscv/opensbi.git |
| cd opensbi |
| make PLATFORM=generic FW_TEXT_START=0x40000000 FW_OPTIONS=0 |
| |
| The VisionFive 2 support for OpenSBI was introduced after the v1.2 release. |
| |
| More detailed description of steps required to build FW_DYNAMIC firmware |
| is beyond the scope of this document. Please refer OpenSBI documenation. |
| (Note: OpenSBI git repo is at https://github.com/riscv/opensbi.git) |
| |
| Now build the U-Boot SPL and U-Boot proper |
| |
| .. code-block:: console |
| |
| cd <U-Boot-dir> |
| make starfive_visionfive2_defconfig |
| make OPENSBI=$(opensbi_dir)/opensbi/build/platform/generic/firmware/fw_dynamic.bin |
| |
| This will generate spl/u-boot-spl.bin and FIT image (u-boot.itb) |
| |
| u-boot-spl.bin cannot be used directly on StarFive VisionFive2,we need |
| to convert the u-boot-spl.bin to u-boot-spl.bin.normal.out with |
| the below command: |
| |
| ./spl_tool -c -f $(Uboot_PATH)/spl/u-boot-spl.bin |
| |
| More detailed description of spl_tool,please refer spl_tool documenation. |
| (Note: spl_tool git repo is at https://github.com/starfive-tech/Tools/tree/master/spl_tool) |
| |
| This will generate u-boot-spl.bin.normal.out file. |
| |
| Flashing |
| ~~~~~~~~ |
| |
| The device firmware loads U-Boot SPL (u-boot-spl.bin.normal.out) from the |
| partition with type GUID 2E54B353-1271-4842-806F-E436D6AF6985. You are free |
| to choose any partition number. |
| |
| With the default configuration U-Boot SPL loads the U-Boot FIT image |
| (u-boot.itb) from partition 2 (CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=0x2). |
| When formatting it is recommended to use GUID |
| BC13C2FF-59E6-4262-A352-B275FD6F7172 for this partition. |
| |
| The FIT image (u-boot.itb) is a combination of OpenSBI's fw_dynamic.bin, |
| u-boot-nodtb.bin and the device tree blob |
| (jh7110-starfive-visionfive-2-v1.3b.dtb or |
| jh7110-starfive-visionfive-2-v1.2a.dtb). |
| |
| Format the SD card (make sure the disk has GPT, otherwise use gdisk to switch) |
| |
| .. code-block:: bash |
| |
| sudo sgdisk --clear \ |
| --set-alignment=2 \ |
| --new=1:4096:8191 --change-name=1:spl --typecode=1:2E54B353-1271-4842-806F-E436D6AF6985\ |
| --new=2:8192:16383 --change-name=2:uboot --typecode=2:BC13C2FF-59E6-4262-A352-B275FD6F7172 \ |
| --new=3:16384:1654784 --change-name=3:system --typecode=3:EBD0A0A2-B9E5-4433-87C0-68B6B72699C7 \ |
| /dev/sdb |
| |
| Program the SD card |
| |
| .. code-block:: bash |
| |
| sudo dd if=u-boot-spl.bin.normal.out of=/dev/sdb1 |
| sudo dd if=u-boot.itb of=/dev/sdb2 |
| |
| sudo mount /dev/sdb3 /mnt/ |
| sudo cp u-boot-spl.bin.normal.out /mnt/ |
| sudo cp u-boot.itb /mnt/ |
| sudo cp Image.gz /mnt/ |
| sudo cp initramfs.cpio.gz /mnt/ |
| sudo cp jh7110-starfive-visionfive-2.dtb /mnt/ |
| sudo umount /mnt |
| |
| Booting |
| ~~~~~~~ |
| |
| The board provides the DIP switches MSEL[1:0] to select the boot device. |
| To select booting from SD-card set the DIP switches MSEL[1:0] to 10. |
| |
| Once you plugin the sdcard and power up, you should see the U-Boot prompt. |
| |
| Sample boot log from StarFive VisionFive2 board |
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
| |
| .. code-block:: none |
| |
| |
| U-Boot SPL 2023.04-rc2-00055-gfc43b9c51a-dirty (Mar 02 2023 - 10:51:39 +0800) |
| DDR version: dc2e84f0. |
| Trying to boot from MMC2 |
| |
| OpenSBI v1.2-80-g4b28afc |
| ____ _____ ____ _____ |
| / __ \ / ____| _ \_ _| |
| | | | |_ __ ___ _ __ | (___ | |_) || | |
| | | | | '_ \ / _ \ '_ \ \___ \| _ < | | |
| | |__| | |_) | __/ | | |____) | |_) || |_ |
| \____/| .__/ \___|_| |_|_____/|___/_____| |
| | | |
| |_| |
| |
| Platform Name : StarFive VisionFive 2 v1.3B |
| Platform Features : medeleg |
| Platform HART Count : 5 |
| Platform IPI Device : aclint-mswi |
| Platform Timer Device : aclint-mtimer @ 4000000Hz |
| Platform Console Device : uart8250 |
| Platform HSM Device : --- |
| Platform PMU Device : --- |
| Platform Reboot Device : --- |
| Platform Shutdown Device : --- |
| Platform Suspend Device : --- |
| Firmware Base : 0x40000000 |
| Firmware Size : 264 KB |
| Firmware RW Offset : 0x20000 |
| Runtime SBI Version : 1.0 |
| |
| Domain0 Name : root |
| Domain0 Boot HART : 2 |
| Domain0 HARTs : 0*,1*,2*,3*,4* |
| Domain0 Region00 : 0x0000000002000000-0x000000000200ffff M: (I,R,W) S/U: () |
| Domain0 Region01 : 0x0000000040000000-0x000000004001ffff M: (R,X) S/U: () |
| Domain0 Region02 : 0x0000000040000000-0x000000004007ffff M: (R,W) S/U: () |
| Domain0 Region03 : 0x0000000000000000-0xffffffffffffffff M: (R,W,X) S/U: (R,W,X) |
| Domain0 Next Address : 0x0000000040200000 |
| Domain0 Next Arg1 : 0x0000000040287970 |
| Domain0 Next Mode : S-mode |
| Domain0 SysReset : yes |
| Domain0 SysSuspend : yes |
| |
| Boot HART ID : 2 |
| Boot HART Domain : root |
| Boot HART Priv Version : v1.11 |
| Boot HART Base ISA : rv64imafdcbx |
| Boot HART ISA Extensions : none |
| Boot HART PMP Count : 8 |
| Boot HART PMP Granularity : 4096 |
| Boot HART PMP Address Bits: 34 |
| Boot HART MHPM Count : 2 |
| Boot HART MIDELEG : 0x0000000000000222 |
| Boot HART MEDELEG : 0x000000000000b109 |
| |
| |
| U-Boot 2023.04-rc2-00055-gfc43b9c51a-dirty (Mar 02 2023 - 10:51:39 +0800) |
| |
| CPU: rv64imac_zba_zbb |
| Model: StarFive VisionFive 2 v1.3B |
| DRAM: 8 GiB |
| Core: 107 devices, 18 uclasses, devicetree: separate |
| MMC: mmc@16010000: 0, mmc@16020000: 1 |
| Loading Environment from nowhere... OK |
| In: serial@10000000 |
| Out: serial@10000000 |
| Err: serial@10000000 |
| Net: No ethernet found. |
| Working FDT set to ff74a340 |
| Hit any key to stop autoboot: 0 |
| StarFive # |
| StarFive #version |
| U-Boot 2023.04-rc2-00055-gfc43b9c51a-dirty (Mar 02 2023 - 10:51:39 +0800) |
| |
| riscv64-buildroot-linux-gnu-gcc.br_real (Buildroot VF2_515_v1.0.0_rc4) 10.3.0 |
| GNU ld (GNU Binutils) 2.36.1 |
| StarFive # |
| StarFive #mmc dev 1 |
| switch to partitions #0, OK |
| mmc1 is current device |
| StarFive #mmc info |
| Device: mmc@16020000 |
| Manufacturer ID: 9f |
| OEM: 5449 |
| Name: SD64G |
| Bus Speed: 50000000 |
| Mode: SD High Speed (50MHz) |
| Rd Block Len: 512 |
| SD version 3.0 |
| High Capacity: Yes |
| Capacity: 58.3 GiB |
| Bus Width: 4-bit |
| Erase Group Size: 512 Bytes |
| StarFive # |
| StarFive #mmc part |
| |
| Partition Map for MMC device 1 -- Partition Type: EFI |
| |
| Part Start LBA End LBA Name |
| Attributes |
| Type GUID |
| Partition GUID |
| 1 0x00001000 0x00001fff "spl" |
| attrs: 0x0000000000000000 |
| type: 2e54b353-1271-4842-806f-e436d6af6985 |
| (2e54b353-1271-4842-806f-e436d6af6985) |
| guid: d5ee2056-3020-475b-9a33-25b4257c9f12 |
| 2 0x00002000 0x00003fff "uboot" |
| attrs: 0x0000000000000000 |
| type: bc13c2ff-59e6-4262-a352-b275fd6f7172 |
| (bc13c2ff-59e6-4262-a352-b275fd6f7172) |
| guid: 379ab7fe-fd0c-4149-b758-960c1cbfc0cc |
| 3 0x00004000 0x00194000 "system" |
| attrs: 0x0000000000000000 |
| type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7 |
| (data) |
| guid: 539a6df9-4655-4953-8541-733ca36eb1db |
| StarFive # |
| StarFive #fatls mmc 1:3 |
| 6429424 Image.gz |
| 717705 u-boot.itb |
| 125437 u-boot-spl.bin.normal.out |
| 152848495 initramfs.cpio.gz |
| 11285 jh7110-starfive-visionfive-2-v1.3b.dtb |
| |
| 5 file(s), 0 dir(s) |
| |
| StarFive #fatload mmc 1:3 ${kernel_addr_r} Image.gz |
| 6429424 bytes read in 394 ms (15.6 MiB/s) |
| StarFive #fatload mmc 1:3 ${fdt_addr_r} jh7110-starfive-visionfive-2.dtb |
| 11285 bytes read in 5 ms (2.2 MiB/s) |
| StarFive #fatload mmc 1:3 ${ramdisk_addr_r} initramfs.cpio.gz |
| 152848495 bytes read in 9271 ms (15.7 MiB/s) |
| StarFive #booti ${kernel_addr_r} ${ramdisk_addr_r}:${filesize} ${fdt_addr_r} |
| Uncompressing Kernel Image |
| ## Flattened Device Tree blob at 46000000 |
| Booting using the fdt blob at 0x46000000 |
| Working FDT set to 46000000 |
| Loading Ramdisk to f5579000, end fe73d86f ... OK |
| Loading Device Tree to 00000000f5573000, end 00000000f5578c14 ... OK |
| Working FDT set to f5573000 |
| |
| Starting kernel ... |
| |
| |
| ] Linux version 6.2.0-starfive-00026-g11934a315b67 (wyh@wyh-VirtualBox) (riscv64-linux-gnu-gcc (Ubuntu 7.5.0-3ubuntu1~18.04) 7.5.0, GNU ld (GNU Binutils for Ubuntu) 2.30) #1 SMP Thu Mar 2 14:51:36 CST 2023 |
| [ 0.000000] OF: fdt: Ignoring memory range 0x40000000 - 0x40200000 |
| [ 0.000000] Machine model: StarFive VisionFive 2 v1.3B |
| [ 0.000000] efi: UEFI not found. |
| [ 0.000000] Zone ranges: |
| [ 0.000000] DMA32 [mem 0x0000000040200000-0x00000000ffffffff] |
| [ 0.000000] Normal [mem 0x0000000100000000-0x000000013fffffff] |
| [ 0.000000] Movable zone start for each node |
| [ 0.000000] Early memory node ranges |
| [ 0.000000] node 0: [mem 0x0000000040200000-0x000000013fffffff] |
| [ 0.000000] Initmem setup node 0 [mem 0x0000000040200000-0x000000013fffffff] |
| [ 0.000000] On node 0, zone DMA32: 512 pages in unavailable ranges |
| [ 0.000000] SBI specification v1.0 detected |
| [ 0.000000] SBI implementation ID=0x1 Version=0x10002 |
| [ 0.000000] SBI TIME extension detected |
| [ 0.000000] SBI IPI extension detected |
| [ 0.000000] SBI RFENCE extension detected |
| [ 0.000000] SBI HSM extension detected |
| [ 0.000000] CPU with hartid=0 is not available |
| [ 0.000000] CPU with hartid=0 is not available |
| [ 0.000000] CPU with hartid=0 is not available |
| [ 0.000000] riscv: base ISA extensions acdfim |
| [ 0.000000] riscv: ELF capabilities acdfim |
| [ 0.000000] percpu: Embedded 18 pages/cpu s35960 r8192 d29576 u73728 |
| [ 0.000000] pcpu-alloc: s35960 r8192 d29576 u73728 alloc=18*4096 |
| [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 |
| [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1031688 |
| [ 0.000000] Kernel command line: console=ttyS0,115200 debug rootwait earlycon=sbi |
| [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) |
| [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) |
| [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off |
| [ 0.000000] software IO TLB: area num 4. |
| [ 0.000000] software IO TLB: mapped [mem 0x00000000f1573000-0x00000000f5573000] (64MB) |
| [ 0.000000] Virtual kernel memory layout: |
| [ 0.000000] fixmap : 0xffffffc6fee00000 - 0xffffffc6ff000000 (2048 kB) |
| [ 0.000000] pci io : 0xffffffc6ff000000 - 0xffffffc700000000 ( 16 MB) |
| [ 0.000000] vmemmap : 0xffffffc700000000 - 0xffffffc800000000 (4096 MB) |
| [ 0.000000] vmalloc : 0xffffffc800000000 - 0xffffffd800000000 ( 64 GB) |
| [ 0.000000] modules : 0xffffffff0136a000 - 0xffffffff80000000 (2028 MB) |
| [ 0.000000] lowmem : 0xffffffd800000000 - 0xffffffd8ffe00000 (4094 MB) |
| [ 0.000000] kernel : 0xffffffff80000000 - 0xffffffffffffffff (2047 MB) |
| [ 0.000000] Memory: 3867604K/4192256K available (8012K kernel code, 4919K rwdata, 4096K rodata, 2190K init, 476K bss, 324652K reserved, 0K cma-reserved) |
| [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 |
| [ 0.000000] rcu: Hierarchical RCU implementation. |
| [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. |
| [ 0.000000] rcu: RCU debug extended QS entry/exit. |
| [ 0.000000] Tracing variant of Tasks RCU enabled. |
| [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. |
| [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 |
| [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 |
| [ 0.000000] CPU with hartid=0 is not available |
| [ 0.000000] riscv-intc: unable to find hart id for /cpus/cpu@0/interrupt-controller |
| [ 0.000000] riscv-intc: 64 local interrupts mapped |
| [ 0.000000] plic: interrupt-controller@c000000: mapped 136 interrupts with 4 handlers for 9 contexts. |
| [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. |
| [ 0.000000] riscv-timer: riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [4] |
| [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 881590404240 ns |
| [ 0.000003] sched_clock: 64 bits at 4MHz, resolution 250ns, wraps every 2199023255500ns |
| [ 0.000437] Console: colour dummy device 80x25 |
| [ 0.000568] Calibrating delay loop (skipped), value calculated using timer frequency.. 8.00 BogoMIPS (lpj=16000) |
| [ 0.000602] pid_max: default: 32768 minimum: 301 |
| [ 0.000752] LSM: initializing lsm=capability,integrity |
| [ 0.001071] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) |
| [ 0.001189] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) |
| [ 0.004201] CPU node for /cpus/cpu@0 exist but the possible cpu range is :0-3 |
| [ 0.007426] cblist_init_generic: Setting adjustable number of callback queues. |
| [ 0.007457] cblist_init_generic: Setting shift to 2 and lim to 1. |
| [ 0.007875] riscv: ELF compat mode unsupported |
| [ 0.007902] ASID allocator disabled (0 bits) |
| [ 0.008405] rcu: Hierarchical SRCU implementation. |
| [ 0.008426] rcu: Max phase no-delay instances is 1000. |
| [ 0.009247] EFI services will not be available. |
| [ 0.010738] smp: Bringing up secondary CPUs ... |
| [ 0.018358] smp: Brought up 1 node, 4 CPUs |
| [ 0.021776] devtmpfs: initialized |
| [ 0.027337] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns |
| [ 0.027389] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) |
| [ 0.027888] pinctrl core: initialized pinctrl subsystem |
| [ 0.029881] NET: Registered PF_NETLINK/PF_ROUTE protocol family |
| [ 0.030401] audit: initializing netlink subsys (disabled) |
| [ 0.031041] audit: type=2000 audit(0.028:1): state=initialized audit_enabled=0 res=1 |
| [ 0.031943] cpuidle: using governor menu |
| [ 0.043011] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages |
| [ 0.043033] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page |
| [ 0.044943] iommu: Default domain type: Translated |
| [ 0.044965] iommu: DMA domain TLB invalidation policy: strict mode |
| [ 0.046089] SCSI subsystem initialized |
| [ 0.046733] libata version 3.00 loaded. |
| [ 0.047231] usbcore: registered new interface driver usbfs |
| [ 0.047315] usbcore: registered new interface driver hub |
| [ 0.047420] usbcore: registered new device driver usb |
| [ 0.049770] vgaarb: loaded |
| [ 0.050277] clocksource: Switched to clocksource riscv_clocksource |
| [ 0.084690] NET: Registered PF_INET protocol family |
| [ 0.085561] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) |
| [ 0.093010] tcp_listen_portaddr_hash hash table entries: 2048 (order: 4, 65536 bytes, linear) |
| [ 0.093152] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) |
| [ 0.093224] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) |
| [ 0.093821] TCP bind hash table entries: 32768 (order: 9, 2097152 bytes, linear) |
| [ 0.117880] TCP: Hash tables configured (established 32768 bind 32768) |
| [ 0.118500] UDP hash table entries: 2048 (order: 5, 196608 bytes, linear) |
| [ 0.118881] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes, linear) |
| [ 0.119675] NET: Registered PF_UNIX/PF_LOCAL protocol family |
| [ 0.121749] RPC: Registered named UNIX socket transport module. |
| [ 0.121776] RPC: Registered udp transport module. |
| [ 0.121784] RPC: Registered tcp transport module. |
| [ 0.121791] RPC: Registered tcp NFSv4.1 backchannel transport module. |
| [ 0.121816] PCI: CLS 0 bytes, default 64 |
| [ 0.124101] Unpacking initramfs... |
| [ 0.125468] workingset: timestamp_bits=46 max_order=20 bucket_order=0 |
| [ 0.128372] NFS: Registering the id_resolver key type |
| [ 0.128498] Key type id_resolver registered |
| [ 0.128525] Key type id_legacy registered |
| [ 0.128625] nfs4filelayout_init: NFSv4 File Layout Driver Registering... |
| [ 0.128649] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... |
| [ 0.129358] 9p: Installing v9fs 9p2000 file system support |
| [ 0.130179] NET: Registered PF_ALG protocol family |
| [ 0.130499] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) |
| [ 0.130544] io scheduler mq-deadline registered |
| [ 0.130556] io scheduler kyber registered |
| [ 0.416754] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled |
| [ 0.420857] SuperH (H)SCI(F) driver initialized |
| [ 0.443735] loop: module loaded |
| [ 0.448605] e1000e: Intel(R) PRO/1000 Network Driver |
| [ 0.448627] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. |
| [ 0.450716] usbcore: registered new interface driver uas |
| [ 0.450832] usbcore: registered new interface driver usb-storage |
| [ 0.451638] mousedev: PS/2 mouse device common for all mice |
| [ 0.453465] sdhci: Secure Digital Host Controller Interface driver |
| [ 0.453487] sdhci: Copyright(c) Pierre Ossman |
| [ 0.453584] sdhci-pltfm: SDHCI platform and OF driver helper |
| [ 0.454140] usbcore: registered new interface driver usbhid |
| [ 0.454174] usbhid: USB HID core driver |
| [ 0.454833] riscv-pmu-sbi: SBI PMU extension is available |
| [ 0.454920] riscv-pmu-sbi: 16 firmware and 4 hardware counters |
| [ 0.454942] riscv-pmu-sbi: Perf sampling/filtering is not supported as sscof extension is not available |
| [ 0.457071] NET: Registered PF_INET6 protocol family |
| [ 0.460627] Segment Routing with IPv6 |
| [ 0.460821] In-situ OAM (IOAM) with IPv6 |
| [ 0.461005] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver |
| [ 0.462712] NET: Registered PF_PACKET protocol family |
| [ 0.462933] 9pnet: Installing 9P2000 support |
| [ 0.463141] Key type dns_resolver registered |
| [ 0.463168] start plist test |
| [ 0.469261] end plist test |
| [ 0.506774] debug_vm_pgtable: [debug_vm_pgtable ]: Validating architecture page table helpers |
| [ 0.553683] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. |
| [ 0.554741] starfive-jh7110-sys-pinctrl 13040000.pinctrl: StarFive GPIO chip registered 64 GPIOs |
| [ 0.555900] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation. |
| [ 0.556772] starfive-jh7110-aon-pinctrl 17020000.pinctrl: StarFive GPIO chip registered 4 GPIOs |
| [ 0.559454] printk: console [ttyS0] disabled |
| [ 0.579948] 10000000.serial: ttyS0 at MMIO 0x10000000 (irq = 3, base_baud = 1500000) is a 16550A |
| [ 0.580082] printk: console [ttyS0] enabled |
| [ 13.642680] Freeing initrd memory: 149264K |
| [ 13.651051] Freeing unused kernel image (initmem) memory: 2188K |
| [ 13.666431] Run /init as init process |
| [ 13.670116] with arguments: |
| [ 13.673168] /init |
| [ 13.675488] with environment: |
| [ 13.678668] HOME=/ |
| [ 13.681038] TERM=linux |
| Starting syslogd: OK |
| Starting klogd: OK |
| Running sysctl: OK |
| Populating /dev using udev: [ 14.145944] udevd[93]: starting version 3.2.10 |
| [ 15.214287] random: crng init done |
| [ 15.240816] udevd[94]: starting eudev-3.2.10 |
| done |
| Saving random seed: OK |
| Starting system message bus: dbus[122]: Unknown username "pulse" in message bus configuration file |
| done |
| Starting rpcbind: OK |
| Starting iptables: OK |
| Starting bluetoothd: OK |
| Starting network: Waiting for interface eth0 to appear............... timeout! |
| run-parts: /etc/network/if-pre-up.d/wait_iface: exit status 1 |
| FAIL |
| Starting dropbear sshd: OK |
| Starting NFS statd: OK |
| Starting NFS services: OK |
| Starting NFS daemon: rpc.nfsd: Unable to access /proc/fs/nfsd errno 2 (No such file or directory). |
| Please try, as root, 'mount -t nfsd nfsd /proc/fs/nfsd' and then restart rpc.nfsd to correct the problem |
| FAIL |
| Starting NFS mountd: OK |
| Starting DHCP server: FAIL |
| |
| Welcome to Buildroot |
| buildroot login: |
| |
| Booting from SPI |
| ---------------- |
| |
| Use Building steps from "Booting from MMC using U-Boot SPL" section. |
| |
| Partition the SPI in Linux via mtdblock. (Require to boot the board in |
| SD boot mode by enabling MTD block in Linux) |
| |
| Use prebuilt image from here [1], which support to partition the SPI flash. |
| |
| |
| Program the SPI (Require to boot the board in SD boot mode) |
| |
| Execute below steps on U-Boot proper, |
| |
| .. code-block:: none |
| |
| sf probe |
| fatload mmc 1:3 $kernel_addr_r u-boot.itb |
| sf update $kernel_addr_r 0x100000 $filesize |
| |
| fatload mmc 1:3 $kernel_addr_r u-boot-spl.bin.normal.out |
| sf update $kernel_addr_r 0x0 $filesize |
| |
| |
| Power off the board |
| |
| Change DIP switches MSEL[1:0] are set to 00, select the boot mode to flash |
| |
| Power up the board. |