| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * Copyright 2012 ST-Ericsson AB |
| */ |
| |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/leds/common.h> |
| #include "ste-href-family-pinctrl.dtsi" |
| |
| / { |
| memory { |
| device_type = "memory"; |
| reg = <0x00000000 0x20000000>; |
| }; |
| |
| battery: battery { |
| compatible = "simple-battery"; |
| battery-type = "lithium-ion-polymer"; |
| }; |
| |
| thermal-zones { |
| battery-thermal { |
| /* This zone will be polled by the battery temperature code */ |
| polling-delay = <0>; |
| polling-delay-passive = <0>; |
| thermal-sensors = <&bat_therm>; |
| |
| trips { |
| battery-crit-hi { |
| temperature = <70000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| }; |
| |
| bat_therm: thermistor { |
| compatible = "murata,ncp18wb473"; |
| io-channels = <&gpadc 0x02>; /* BatTemp */ |
| pullup-uv = <1800000>; |
| pullup-ohm = <230000>; |
| pulldown-ohm = <0>; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| soc { |
| serial@80120000 { |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&u0_a_1_default>; |
| pinctrl-1 = <&u0_a_1_sleep>; |
| status = "okay"; |
| }; |
| |
| /* This UART is unused and thus left disabled */ |
| serial@80121000 { |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&u1rxtx_a_1_default>; |
| pinctrl-1 = <&u1rxtx_a_1_sleep>; |
| }; |
| |
| serial@80007000 { |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&u2rxtx_c_1_default>; |
| pinctrl-1 = <&u2rxtx_c_1_sleep>; |
| status = "okay"; |
| }; |
| |
| i2c@80004000 { |
| pinctrl-names = "default","sleep"; |
| pinctrl-0 = <&i2c0_a_1_default>; |
| pinctrl-1 = <&i2c0_a_1_sleep>; |
| status = "okay"; |
| }; |
| |
| i2c@80122000 { |
| pinctrl-names = "default","sleep"; |
| pinctrl-0 = <&i2c1_b_2_default>; |
| pinctrl-1 = <&i2c1_b_2_sleep>; |
| status = "okay"; |
| }; |
| |
| i2c@80128000 { |
| pinctrl-names = "default","sleep"; |
| pinctrl-0 = <&i2c2_b_2_default>; |
| pinctrl-1 = <&i2c2_b_2_sleep>; |
| status = "okay"; |
| lp5521@33 { |
| compatible = "national,lp5521"; |
| reg = <0x33>; |
| label = "lp5521_pri"; |
| clock-mode = /bits/ 8 <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| led@0 { |
| reg = <0>; |
| led-cur = /bits/ 8 <0x2f>; |
| max-cur = /bits/ 8 <0x5f>; |
| color = <LED_COLOR_ID_BLUE>; |
| linux,default-trigger = "heartbeat"; |
| }; |
| led@1 { |
| reg = <1>; |
| led-cur = /bits/ 8 <0x2f>; |
| max-cur = /bits/ 8 <0x5f>; |
| color = <LED_COLOR_ID_BLUE>; |
| }; |
| led@2 { |
| reg = <2>; |
| led-cur = /bits/ 8 <0x2f>; |
| max-cur = /bits/ 8 <0x5f>; |
| color = <LED_COLOR_ID_BLUE>; |
| }; |
| }; |
| lp5521@34 { |
| compatible = "national,lp5521"; |
| reg = <0x34>; |
| label = "lp5521_sec"; |
| clock-mode = /bits/ 8 <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| led@0 { |
| reg = <0>; |
| led-cur = /bits/ 8 <0x2f>; |
| max-cur = /bits/ 8 <0x5f>; |
| color = <LED_COLOR_ID_BLUE>; |
| }; |
| led@1 { |
| reg = <1>; |
| led-cur = /bits/ 8 <0x2f>; |
| max-cur = /bits/ 8 <0x5f>; |
| color = <LED_COLOR_ID_BLUE>; |
| }; |
| led@2 { |
| reg = <2>; |
| led-cur = /bits/ 8 <0x2f>; |
| max-cur = /bits/ 8 <0x5f>; |
| color = <LED_COLOR_ID_BLUE>; |
| }; |
| }; |
| bh1780@29 { |
| compatible = "rohm,bh1780gli"; |
| reg = <0x29>; |
| }; |
| }; |
| |
| i2c@80110000 { |
| pinctrl-names = "default","sleep"; |
| pinctrl-0 = <&i2c3_c_2_default>; |
| pinctrl-1 = <&i2c3_c_2_sleep>; |
| status = "okay"; |
| }; |
| |
| // External Micro SD slot |
| mmc@80126000 { |
| arm,primecell-periphid = <0x10480180>; |
| max-frequency = <100000000>; |
| bus-width = <4>; |
| cap-sd-highspeed; |
| cap-mmc-highspeed; |
| sd-uhs-sdr12; |
| sd-uhs-sdr25; |
| full-pwr-cycle; |
| st,sig-dir-dat0; |
| st,sig-dir-dat2; |
| st,sig-dir-cmd; |
| st,sig-pin-fbclk; |
| vmmc-supply = <&ab8500_ldo_aux3_reg>; |
| vqmmc-supply = <&vmmci>; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&mc0_a_1_default &sdi0_default_mode>; |
| pinctrl-1 = <&mc0_a_1_sleep>; |
| |
| status = "okay"; |
| }; |
| |
| // WLAN SDIO channel |
| mmc@80118000 { |
| arm,primecell-periphid = <0x10480180>; |
| max-frequency = <100000000>; |
| bus-width = <4>; |
| non-removable; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&mc1_a_1_default>; |
| pinctrl-1 = <&mc1_a_1_sleep>; |
| |
| status = "okay"; |
| }; |
| |
| // PoP:ed eMMC |
| mmc@80005000 { |
| arm,primecell-periphid = <0x10480180>; |
| max-frequency = <100000000>; |
| bus-width = <8>; |
| cap-mmc-highspeed; |
| non-removable; |
| no-sdio; |
| no-sd; |
| vmmc-supply = <&db8500_vsmps2_reg>; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&mc2_a_1_default>; |
| pinctrl-1 = <&mc2_a_1_sleep>; |
| |
| status = "okay"; |
| }; |
| |
| // On-board eMMC |
| mmc@80114000 { |
| arm,primecell-periphid = <0x10480180>; |
| max-frequency = <100000000>; |
| bus-width = <8>; |
| cap-mmc-highspeed; |
| non-removable; |
| no-sdio; |
| no-sd; |
| vmmc-supply = <&ab8500_ldo_aux2_reg>; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&mc4_a_1_default>; |
| pinctrl-1 = <&mc4_a_1_sleep>; |
| |
| status = "okay"; |
| }; |
| |
| msp0: msp@80123000 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&msp0txrxtfstck_a_1_default>; |
| status = "okay"; |
| }; |
| |
| msp1: msp@80124000 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&msp1txrx_a_1_default>; |
| status = "okay"; |
| }; |
| |
| msp2: msp@80117000 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&msp2_a_1_default>; |
| }; |
| |
| msp3: msp@80125000 { |
| status = "okay"; |
| }; |
| |
| prcmu@80157000 { |
| ab8500 { |
| gpio { |
| }; |
| |
| phy { |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&usb_a_1_default>; |
| pinctrl-1 = <&usb_a_1_sleep>; |
| }; |
| |
| regulator { |
| ab8500_ldo_aux1_reg: ab8500_ldo_aux1 { |
| regulator-name = "V-DISPLAY"; |
| }; |
| |
| ab8500_ldo_aux2_reg: ab8500_ldo_aux2 { |
| regulator-name = "V-eMMC1"; |
| }; |
| |
| ab8500_ldo_aux3_reg: ab8500_ldo_aux3 { |
| regulator-name = "V-MMC-SD"; |
| }; |
| |
| ab8500_ldo_intcore_reg: ab8500_ldo_intcore { |
| regulator-name = "V-INTCORE"; |
| }; |
| |
| ab8500_ldo_tvout_reg: ab8500_ldo_tvout { |
| regulator-name = "V-TVOUT"; |
| }; |
| |
| ab8500_ldo_audio_reg: ab8500_ldo_audio { |
| regulator-name = "V-AUD"; |
| }; |
| |
| ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 { |
| regulator-name = "V-AMIC1"; |
| }; |
| |
| ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 { |
| regulator-name = "V-AMIC2"; |
| }; |
| |
| ab8500_ldo_dmic_reg: ab8500_ldo_dmic { |
| regulator-name = "V-DMIC"; |
| }; |
| |
| ab8500_ldo_ana_reg: ab8500_ldo_ana { |
| regulator-name = "V-CSI/DSI"; |
| }; |
| }; |
| }; |
| }; |
| |
| pinctrl { |
| sdi0 { |
| sdi0_default_mode: sdi0_default { |
| /* Some boards set additional settings here */ |
| }; |
| }; |
| }; |
| |
| mcde@a0350000 { |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&lcd_default_mode>; |
| pinctrl-1 = <&lcd_sleep_mode>; |
| }; |
| }; |
| }; |