| .. SPDX-License-Identifier: GPL-2.0+ |
| .. sectionauthor:: Wadim Egorov <w.egorov@phytec.de> |
| |
| phyCORE-AM62x |
| ============= |
| |
| The `phyCORE-AM62x <https://www.phytec.com/product/phycore-am62x>`_ is a |
| SoM (System on Module) featuring TI's AM62x SoC. It can be used in combination |
| with different carrier boards. This module can come with different sizes and |
| models for DDR, eMMC, SPI NOR Flash and various SoCs from the AM62x family. |
| |
| A development Kit, called `phyBOARD-Lyra <https://www.phytec.com/product/phyboard-am62x>`_ |
| is used as a carrier board reference design around the AM62x SoM. |
| |
| Quickstart |
| ---------- |
| |
| * Download sources and TI firmware blobs |
| * Build Trusted Firmware-A |
| * Build OP-TEE |
| * Build U-Boot for the R5 |
| * Build U-Boot for the A53 |
| * Create bootable uSD Card |
| * Boot |
| |
| Sources |
| ------- |
| |
| .. include:: ../ti/k3.rst |
| :start-after: .. k3_rst_include_start_boot_sources |
| :end-before: .. k3_rst_include_end_boot_sources |
| |
| Build procedure |
| --------------- |
| |
| Setup the environment variables: |
| |
| .. include:: ../ti/k3.rst |
| :start-after: .. k3_rst_include_start_common_env_vars_desc |
| :end-before: .. k3_rst_include_end_common_env_vars_desc |
| |
| .. include:: ../ti/k3.rst |
| :start-after: .. k3_rst_include_start_board_env_vars_desc |
| :end-before: .. k3_rst_include_end_board_env_vars_desc |
| |
| Set the variables corresponding to this platform: |
| |
| .. include:: ../ti/k3.rst |
| :start-after: .. k3_rst_include_start_common_env_vars_defn |
| :end-before: .. k3_rst_include_end_common_env_vars_defn |
| .. code-block:: bash |
| |
| $ export UBOOT_CFG_CORTEXR=phycore_am62x_r5_defconfig |
| $ export UBOOT_CFG_CORTEXA=phycore_am62x_a53_defconfig |
| $ export TFA_BOARD=lite |
| $ # we don't use any extra TFA parameters |
| $ unset TFA_EXTRA_ARGS |
| $ export OPTEE_PLATFORM=k3-am62x |
| $ export OPTEE_EXTRA_ARGS="CFG_WITH_SOFTWARE_PRNG=y" |
| |
| .. include:: ../ti/am62x_sk.rst |
| :start-after: .. am62x_evm_rst_include_start_build_steps |
| :end-before: .. am62x_evm_rst_include_end_build_steps |
| |
| uSD Card creation |
| ----------------- |
| |
| Use fdisk to partition the uSD card. The layout should look similar to: |
| |
| .. code-block:: bash |
| |
| $ sudo fdisk -l /dev/mmcblk0 |
| Disk /dev/mmcblk0: 7.56 GiB, 8120172544 bytes, 15859712 sectors |
| Units: sectors of 1 * 512 = 512 bytes |
| Sector size (logical/physical): 512 bytes / 512 bytes |
| I/O size (minimum/optimal): 512 bytes / 512 bytes |
| Disklabel type: dos |
| Disk identifier: 0x6583d9a3 |
| |
| Device Boot Start End Sectors Size Id Type |
| /dev/mmcblk0p1 * 2048 264191 262144 128M c W95 FAT32 (LBA) |
| /dev/mmcblk0p2 264192 1934953 1670762 815.8M 83 Linux |
| |
| |
| Once partitioned, the boot partition has to be formatted with a FAT filesystem. |
| Assuming the uSD card is `/dev/mmcblk0`: |
| |
| .. code-block:: bash |
| |
| $ mkfs.vfat /dev/mmcblk0p1 |
| |
| To boot from a micro SD card on a HSFS device simply copy the following |
| artifacts to the FAT partition: |
| |
| * tiboot3.bin from R5 build as tiboot3.bin |
| * tispl.bin_unsigned from Cortex-A build as tispl.bin |
| * u-boot.img_unsigned from Cortex-A build as u-boot.img |
| |
| Boot |
| ---- |
| |
| Put the uSD card in the slot on the board and apply power. Check the serial |
| console for output. |
| |
| Flash to SPI NOR |
| ---------------- |
| |
| Below commands can be used to flash the SPI NOR flash; assuming |
| tiboot3.bin, tispl.bin and u-boot.img are stored on the uSD card. |
| |
| .. code-block:: bash |
| |
| sf probe |
| fatload mmc 1 ${loadaddr} tiboot3.bin |
| sf update $loadaddr 0x0 $filesize |
| fatload mmc 1 ${loadaddr} tispl.bin |
| sf update $loadaddr 0x80000 $filesize |
| fatload mmc 1 ${loadaddr} u-boot.img |
| sf update $loadaddr 0x280000 $filesize |
| |
| |
| Boot Modes |
| ---------- |
| |
| The phyCORE-AM62x development kit supports booting from many different |
| interfaces. By default, the development kit is set to boot from the micro-SD |
| card. To change the boot device, DIP switches S5 and S6 can be used. |
| Boot switches should be changed with power off. |
| |
| .. list-table:: Boot Modes |
| :widths: 16 16 16 |
| :header-rows: 1 |
| |
| * - Switch Label |
| - SW5: 12345678 |
| - SW6: 12345678 |
| |
| * - uSD |
| - 11000010 |
| - 01000000 |
| |
| * - eMMC |
| - 11010010 |
| - 00000000 |
| |
| * - OSPI |
| - 11010000 |
| - 10000000 |
| |
| * - UART |
| - 11011100 |
| - 00000000 |
| |
| Further Information |
| ------------------- |
| |
| Please see :doc:`../ti/am62x_sk` chapter for further AM62 SoC related documentation |
| and https://docs.phytec.com/phycore-am62x for vendor documentation. |