| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright 2020 NXP |
| */ |
| |
| #include <common.h> |
| #include <env.h> |
| #include <init.h> |
| #include <malloc.h> |
| #include <errno.h> |
| #include <asm/io.h> |
| #include <miiphy.h> |
| #include <netdev.h> |
| #include <asm/mach-imx/iomux-v3.h> |
| #include <asm-generic/gpio.h> |
| #include <fsl_esdhc_imx.h> |
| #include <mmc.h> |
| #include <asm/arch/imx8mq_pins.h> |
| #include <asm/arch/sys_proto.h> |
| #include <asm/mach-imx/gpio.h> |
| #include <asm/arch/clock.h> |
| #include <spl.h> |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| #define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1) |
| |
| #define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE) |
| |
| static iomux_v3_cfg_t const wdog_pads[] = { |
| IMX8MQ_PAD_GPIO1_IO02__WDOG1_WDOG_B | MUX_PAD_CTRL(WDOG_PAD_CTRL), |
| }; |
| |
| static iomux_v3_cfg_t const uart_pads[] = { |
| IMX8MQ_PAD_UART1_RXD__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL), |
| IMX8MQ_PAD_UART1_TXD__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL), |
| }; |
| |
| int board_early_init_f(void) |
| { |
| struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR; |
| |
| imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads)); |
| set_wdog_reset(wdog); |
| |
| imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads)); |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_FEC_MXC |
| static int setup_fec(void) |
| { |
| struct iomuxc_gpr_base_regs *gpr = |
| (struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR; |
| |
| /* Use 125M anatop REF_CLK1 for ENET1, not from external */ |
| clrsetbits_le32(&gpr->gpr[1], BIT(13) | BIT(17), 0); |
| return set_clk_enet(ENET_125MHZ); |
| } |
| |
| int board_phy_config(struct phy_device *phydev) |
| { |
| /* enable rgmii rxc skew and phy mode select to RGMII copper */ |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f); |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8); |
| |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05); |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100); |
| |
| if (phydev->drv->config) |
| phydev->drv->config(phydev); |
| return 0; |
| } |
| #endif |
| |
| int board_init(void) |
| { |
| #ifdef CONFIG_FEC_MXC |
| setup_fec(); |
| #endif |
| |
| return 0; |
| } |
| |
| int board_mmc_get_env_dev(int devno) |
| { |
| return devno; |
| } |