| /* |
| * Copyright (C) Marvell International Ltd. and its affiliates |
| * |
| * SPDX-License-Identifier: GPL-2.0 |
| */ |
| |
| #ifndef __DDR3_AXP_CONFIG_H |
| #define __DDR3_AXP_CONFIG_H |
| |
| /* |
| * DDR3_LOG_LEVEL Information |
| * |
| * Level 0: Provides an error code in a case of failure, RL, WL errors |
| * and other algorithm failure |
| * Level 1: Provides the D-Unit setup (SPD/Static configuration) |
| * Level 2: Provides the windows margin as a results of DQS centeralization |
| * Level 3: Provides the windows margin of each DQ as a results of DQS |
| * centeralization |
| */ |
| #ifdef CONFIG_DDR_LOG_LEVEL |
| #define DDR3_LOG_LEVEL CONFIG_DDR_LOG_LEVEL |
| #else |
| #define DDR3_LOG_LEVEL 0 |
| #endif |
| |
| #define DDR3_PBS 1 |
| |
| /* This flag allows the execution of SW WL/RL upon HW failure */ |
| #define DDR3_RUN_SW_WHEN_HW_FAIL 1 |
| |
| /* |
| * General Configurations |
| * |
| * The following parameters are required for proper setup: |
| * |
| * DDR_TARGET_FABRIC - Set desired fabric configuration |
| * (for sample@Reset fabfreq parameter) |
| * DRAM_ECC - Set ECC support 1/0 |
| * BUS_WIDTH - 64/32 bit |
| * CONFIG_SPD_EEPROM - Enables auto detection of DIMMs and their timing values |
| * DQS_CLK_ALIGNED - Set this if CLK and DQS signals are aligned on board |
| * MIXED_DIMM_STATIC - Mixed DIMM + On board devices support (ODT registers |
| * values are taken statically) |
| * DDR3_TRAINING_DEBUG - Debug prints of internal code |
| */ |
| #define DDR_TARGET_FABRIC 5 |
| /* Only enable ECC if the board selects it */ |
| #ifdef CONFIG_BOARD_ECC_SUPPORT |
| #define DRAM_ECC 1 |
| #else |
| #define DRAM_ECC 0 |
| #endif |
| |
| #ifdef CONFIG_DDR_32BIT |
| #define BUS_WIDTH 32 |
| #else |
| #define BUS_WIDTH 64 |
| #endif |
| |
| #undef DQS_CLK_ALIGNED |
| #undef MIXED_DIMM_STATIC |
| #define DDR3_TRAINING_DEBUG 0 |
| #define REG_DIMM_SKIP_WL 0 |
| |
| /* Marvell boards specific configurations */ |
| #if defined(DB_78X60_PCAC) |
| #undef CONFIG_SPD_EEPROM |
| #define STATIC_TRAINING |
| #endif |
| |
| #if defined(DB_78X60_AMC) |
| #undef CONFIG_SPD_EEPROM |
| #undef DRAM_ECC |
| #define DRAM_ECC 1 |
| #endif |
| |
| #ifdef CONFIG_SPD_EEPROM |
| /* |
| * DIMM support parameters: |
| * DRAM_2T - Set Desired 2T Mode - 0 - 1T, 0x1 - 2T, 0x2 - 3T |
| * DIMM_CS_BITMAP - bitmap representing the optional CS in DIMMs |
| * (0xF=CS0+CS1+CS2+CS3, 0xC=CS2+CS3...) |
| */ |
| #define DRAM_2T 0x0 |
| #define DIMM_CS_BITMAP 0xF |
| #define DUNIT_SPD |
| #endif |
| |
| #ifdef DRAM_ECC |
| /* |
| * ECC support parameters: |
| * |
| * U_BOOT_START_ADDR, U_BOOT_SCRUB_SIZE - relevant when using ECC and need |
| * to configure the scrubbing area |
| */ |
| #define TRAINING_SIZE 0x20000 |
| #define U_BOOT_START_ADDR 0 |
| #define U_BOOT_SCRUB_SIZE 0x1000000 /* TRAINING_SIZE */ |
| #endif |
| |
| /* |
| * Registered DIMM Support - In case registered DIMM is attached, |
| * please supply the following values: |
| * (see JEDEC - JESD82-29A "Definition of the SSTE32882 Registering Clock |
| * Driver with Parity and Quad Chip |
| * Selects for DDR3/DDR3L/DDR3U RDIMM 1.5 V/1.35 V/1.25 V Applications") |
| * RC0: Global Features Control Word |
| * RC1: Clock Driver Enable Control Word |
| * RC2: Timing Control Word |
| * RC3-RC5 - taken from SPD |
| * RC8: Additional IBT Setting Control Word |
| * RC9: Power Saving Settings Control Word |
| * RC10: Encoding for RDIMM Operating Speed |
| * RC11: Operating Voltage VDD and VREFCA Control Word |
| */ |
| #define RDIMM_RC0 0 |
| #define RDIMM_RC1 0 |
| #define RDIMM_RC2 0 |
| #define RDIMM_RC8 0 |
| #define RDIMM_RC9 0 |
| #define RDIMM_RC10 0x2 |
| #define RDIMM_RC11 0x0 |
| |
| #if defined(MIXED_DIMM_STATIC) || !defined(CONFIG_SPD_EEPROM) |
| #define DUNIT_STATIC |
| #endif |
| |
| #if defined(MIXED_DIMM_STATIC) || defined(CONFIG_SPD_EEPROM) |
| /* |
| * This flag allows the user to change the dram refresh cycle in ps, |
| * only in case of SPD or MIX DIMM topology |
| */ |
| #define TREFI_USER_EN |
| |
| #ifdef TREFI_USER_EN |
| #define TREFI_USER 3900000 |
| #endif |
| #endif |
| |
| #ifdef CONFIG_SPD_EEPROM |
| /* |
| * AUTO_DETECTION_SUPPORT - relevant ONLY for Marvell DB boards. |
| * Enables I2C auto detection different options |
| */ |
| #if defined(CONFIG_DB_88F78X60) || defined(CONFIG_DB_88F78X60_REV2) || \ |
| defined(CONFIG_DB_784MP_GP) |
| #define AUTO_DETECTION_SUPPORT |
| #endif |
| #endif |
| |
| #endif /* __DDR3_AXP_CONFIG_H */ |