| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * (C) Copyright 2022-2023 Sumit Garg <sumit.garg@linaro.org> |
| * |
| * Qcom DWMAC specific glue layer |
| */ |
| |
| #include <asm/global_data.h> |
| #include <asm/gpio.h> |
| #include <asm/io.h> |
| #include <clk.h> |
| #include <dm.h> |
| #include <dm/device_compat.h> |
| #include <phy.h> |
| #include <reset.h> |
| #include <syscon.h> |
| #include <linux/bitops.h> |
| #include <linux/delay.h> |
| |
| #include "dwc_eth_qos.h" |
| |
| /* RGMII_IO_MACRO_CONFIG fields */ |
| #define RGMII_CONFIG_FUNC_CLK_EN BIT(30) |
| #define RGMII_CONFIG_POS_NEG_DATA_SEL BIT(23) |
| #define RGMII_CONFIG_GPIO_CFG_RX_INT GENMASK(21, 20) |
| #define RGMII_CONFIG_GPIO_CFG_TX_INT GENMASK(19, 17) |
| #define RGMII_CONFIG_MAX_SPD_PRG_9 GENMASK(16, 8) |
| #define RGMII_CONFIG_MAX_SPD_PRG_2 GENMASK(7, 6) |
| #define RGMII_CONFIG_INTF_SEL GENMASK(5, 4) |
| #define RGMII_CONFIG_BYPASS_TX_ID_EN BIT(3) |
| #define RGMII_CONFIG_LOOPBACK_EN BIT(2) |
| #define RGMII_CONFIG_PROG_SWAP BIT(1) |
| #define RGMII_CONFIG_DDR_MODE BIT(0) |
| |
| /* SDCC_HC_REG_DLL_CONFIG fields */ |
| #define SDCC_DLL_CONFIG_DLL_RST BIT(30) |
| #define SDCC_DLL_CONFIG_PDN BIT(29) |
| #define SDCC_DLL_CONFIG_MCLK_FREQ GENMASK(26, 24) |
| #define SDCC_DLL_CONFIG_CDR_SELEXT GENMASK(23, 20) |
| #define SDCC_DLL_CONFIG_CDR_EXT_EN BIT(19) |
| #define SDCC_DLL_CONFIG_CK_OUT_EN BIT(18) |
| #define SDCC_DLL_CONFIG_CDR_EN BIT(17) |
| #define SDCC_DLL_CONFIG_DLL_EN BIT(16) |
| #define SDCC_DLL_MCLK_GATING_EN BIT(5) |
| #define SDCC_DLL_CDR_FINE_PHASE GENMASK(3, 2) |
| |
| /* SDCC_HC_REG_DDR_CONFIG fields */ |
| #define SDCC_DDR_CONFIG_PRG_DLY_EN BIT(31) |
| #define SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY GENMASK(26, 21) |
| #define SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_CODE GENMASK(29, 27) |
| #define SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_EN BIT(30) |
| #define SDCC_DDR_CONFIG_PRG_RCLK_DLY GENMASK(8, 0) |
| |
| /* SDCC_HC_REG_DLL_CONFIG2 fields */ |
| #define SDCC_DLL_CONFIG2_DLL_CLOCK_DIS BIT(21) |
| #define SDCC_DLL_CONFIG2_MCLK_FREQ_CALC GENMASK(17, 10) |
| #define SDCC_DLL_CONFIG2_DDR_TRAFFIC_INIT_SEL GENMASK(3, 2) |
| #define SDCC_DLL_CONFIG2_DDR_TRAFFIC_INIT_SW BIT(1) |
| #define SDCC_DLL_CONFIG2_DDR_CAL_EN BIT(0) |
| |
| /* SDC4_STATUS bits */ |
| #define SDC4_STATUS_DLL_LOCK BIT(7) |
| |
| /* RGMII_IO_MACRO_CONFIG2 fields */ |
| #define RGMII_CONFIG2_RSVD_CONFIG15 GENMASK(31, 17) |
| #define RGMII_CONFIG2_RGMII_CLK_SEL_CFG BIT(16) |
| #define RGMII_CONFIG2_TX_TO_RX_LOOPBACK_EN BIT(13) |
| #define RGMII_CONFIG2_CLK_DIVIDE_SEL BIT(12) |
| #define RGMII_CONFIG2_RX_PROG_SWAP BIT(7) |
| #define RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL BIT(6) |
| #define RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN BIT(5) |
| |
| struct dwmac_rgmii_regs { |
| u32 io_macro_config; /* 0x00 */ |
| u32 sdcc_hc_dll_config; /* 0x04 */ |
| u32 reserved_1; /* 0x08 */ |
| u32 sdcc_hc_ddr_config; /* 0x0c */ |
| u32 sdcc_hc_dll_config2; /* 0x10 */ |
| u32 sdc4_status; /* 0x14 */ |
| u32 sdcc_usr_ctl; /* 0x18 */ |
| u32 io_macro_config2; /* 0x1c */ |
| u32 io_macro_debug1; /* 0x20 */ |
| u32 reserved_2; /* 0x24 */ |
| u32 emac_sys_low_power_dbg; /* 0x28 */ |
| u32 reserved_3[53]; /* upto 0x100 */ |
| }; |
| |
| static struct dwmac_rgmii_regs emac_v2_3_0_por = { |
| .io_macro_config = 0x00C01343, |
| .sdcc_hc_dll_config = 0x2004642C, |
| .sdcc_hc_ddr_config = 0x00000000, |
| .sdcc_hc_dll_config2 = 0x00200000, |
| .sdcc_usr_ctl = 0x00010800, |
| .io_macro_config2 = 0x00002060 |
| }; |
| |
| static void ethqos_set_func_clk_en(struct dwmac_rgmii_regs *regs) |
| { |
| setbits_le32(®s->io_macro_config, RGMII_CONFIG_FUNC_CLK_EN); |
| } |
| |
| static int ethqos_dll_configure(struct udevice *dev, |
| struct dwmac_rgmii_regs *regs) |
| { |
| unsigned int val; |
| int retry = 1000; |
| |
| /* Set CDR_EN */ |
| setbits_le32(®s->sdcc_hc_dll_config, SDCC_DLL_CONFIG_CDR_EN); |
| |
| /* Set CDR_EXT_EN */ |
| setbits_le32(®s->sdcc_hc_dll_config, SDCC_DLL_CONFIG_CDR_EXT_EN); |
| |
| /* Clear CK_OUT_EN */ |
| clrbits_le32(®s->sdcc_hc_dll_config, SDCC_DLL_CONFIG_CK_OUT_EN); |
| |
| /* Set DLL_EN */ |
| setbits_le32(®s->sdcc_hc_dll_config, SDCC_DLL_CONFIG_DLL_EN); |
| |
| clrbits_le32(®s->sdcc_hc_dll_config, SDCC_DLL_MCLK_GATING_EN); |
| |
| clrbits_le32(®s->sdcc_hc_dll_config, SDCC_DLL_CDR_FINE_PHASE); |
| |
| /* Wait for CK_OUT_EN clear */ |
| do { |
| val = readl(®s->sdcc_hc_dll_config); |
| val &= SDCC_DLL_CONFIG_CK_OUT_EN; |
| if (!val) |
| break; |
| mdelay(1); |
| retry--; |
| } while (retry > 0); |
| if (!retry) |
| dev_err(dev, "Clear CK_OUT_EN timedout\n"); |
| |
| /* Set CK_OUT_EN */ |
| setbits_le32(®s->sdcc_hc_dll_config, SDCC_DLL_CONFIG_CK_OUT_EN); |
| |
| /* Wait for CK_OUT_EN set */ |
| retry = 1000; |
| do { |
| val = readl(®s->sdcc_hc_dll_config); |
| val &= SDCC_DLL_CONFIG_CK_OUT_EN; |
| if (val) |
| break; |
| mdelay(1); |
| retry--; |
| } while (retry > 0); |
| if (!retry) |
| dev_err(dev, "Set CK_OUT_EN timedout\n"); |
| |
| /* Set DDR_CAL_EN */ |
| setbits_le32(®s->sdcc_hc_dll_config2, SDCC_DLL_CONFIG2_DDR_CAL_EN); |
| |
| clrbits_le32(®s->sdcc_hc_dll_config2, |
| SDCC_DLL_CONFIG2_DLL_CLOCK_DIS); |
| |
| clrsetbits_le32(®s->sdcc_hc_dll_config2, |
| SDCC_DLL_CONFIG2_MCLK_FREQ_CALC, 0x1A << 10); |
| |
| clrsetbits_le32(®s->sdcc_hc_dll_config2, |
| SDCC_DLL_CONFIG2_DDR_TRAFFIC_INIT_SEL, BIT(2)); |
| |
| setbits_le32(®s->sdcc_hc_dll_config2, |
| SDCC_DLL_CONFIG2_DDR_TRAFFIC_INIT_SW); |
| |
| return 0; |
| } |
| |
| static int ethqos_rgmii_macro_init(struct udevice *dev, |
| struct dwmac_rgmii_regs *regs, |
| unsigned long speed) |
| { |
| /* Disable loopback mode */ |
| clrbits_le32(®s->io_macro_config2, |
| RGMII_CONFIG2_TX_TO_RX_LOOPBACK_EN); |
| |
| /* Select RGMII, write 0 to interface select */ |
| clrbits_le32(®s->io_macro_config, RGMII_CONFIG_INTF_SEL); |
| |
| switch (speed) { |
| case SPEED_1000: |
| setbits_le32(®s->io_macro_config, RGMII_CONFIG_DDR_MODE); |
| clrbits_le32(®s->io_macro_config, |
| RGMII_CONFIG_BYPASS_TX_ID_EN); |
| setbits_le32(®s->io_macro_config, |
| RGMII_CONFIG_POS_NEG_DATA_SEL); |
| setbits_le32(®s->io_macro_config, RGMII_CONFIG_PROG_SWAP); |
| |
| clrbits_le32(®s->io_macro_config2, |
| RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL); |
| setbits_le32(®s->io_macro_config2, |
| RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN); |
| clrbits_le32(®s->io_macro_config2, |
| RGMII_CONFIG2_RSVD_CONFIG15); |
| setbits_le32(®s->io_macro_config2, |
| RGMII_CONFIG2_RX_PROG_SWAP); |
| |
| /* Set PRG_RCLK_DLY to 57 for 1.8 ns delay */ |
| clrsetbits_le32(®s->sdcc_hc_ddr_config, |
| SDCC_DDR_CONFIG_PRG_RCLK_DLY, 57); |
| setbits_le32(®s->sdcc_hc_ddr_config, SDCC_DDR_CONFIG_PRG_DLY_EN); |
| |
| setbits_le32(®s->io_macro_config, RGMII_CONFIG_LOOPBACK_EN); |
| break; |
| |
| case SPEED_100: |
| setbits_le32(®s->io_macro_config, RGMII_CONFIG_DDR_MODE); |
| setbits_le32(®s->io_macro_config, |
| RGMII_CONFIG_BYPASS_TX_ID_EN); |
| clrbits_le32(®s->io_macro_config, |
| RGMII_CONFIG_POS_NEG_DATA_SEL); |
| clrbits_le32(®s->io_macro_config, RGMII_CONFIG_PROG_SWAP); |
| clrsetbits_le32(®s->io_macro_config, |
| RGMII_CONFIG_MAX_SPD_PRG_2, BIT(6)); |
| |
| clrbits_le32(®s->io_macro_config2, |
| RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL); |
| setbits_le32(®s->io_macro_config2, |
| RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN); |
| clrbits_le32(®s->io_macro_config2, |
| RGMII_CONFIG2_RSVD_CONFIG15); |
| clrbits_le32(®s->io_macro_config2, |
| RGMII_CONFIG2_RX_PROG_SWAP); |
| |
| /* Write 0x5 to PRG_RCLK_DLY_CODE */ |
| clrsetbits_le32(®s->sdcc_hc_ddr_config, |
| SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_CODE, |
| (BIT(29) | BIT(27))); |
| setbits_le32(®s->sdcc_hc_ddr_config, |
| SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY); |
| setbits_le32(®s->sdcc_hc_ddr_config, |
| SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_EN); |
| |
| setbits_le32(®s->io_macro_config, RGMII_CONFIG_LOOPBACK_EN); |
| break; |
| |
| case SPEED_10: |
| setbits_le32(®s->io_macro_config, RGMII_CONFIG_DDR_MODE); |
| setbits_le32(®s->io_macro_config, |
| RGMII_CONFIG_BYPASS_TX_ID_EN); |
| clrbits_le32(®s->io_macro_config, |
| RGMII_CONFIG_POS_NEG_DATA_SEL); |
| clrbits_le32(®s->io_macro_config, RGMII_CONFIG_PROG_SWAP); |
| clrsetbits_le32(®s->io_macro_config, |
| RGMII_CONFIG_MAX_SPD_PRG_9, |
| BIT(12) | GENMASK(9, 8)); |
| |
| clrbits_le32(®s->io_macro_config2, |
| RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL); |
| clrbits_le32(®s->io_macro_config2, |
| RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN); |
| clrbits_le32(®s->io_macro_config2, |
| RGMII_CONFIG2_RSVD_CONFIG15); |
| clrbits_le32(®s->io_macro_config2, |
| RGMII_CONFIG2_RX_PROG_SWAP); |
| |
| /* Write 0x5 to PRG_RCLK_DLY_CODE */ |
| clrsetbits_le32(®s->sdcc_hc_ddr_config, |
| SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_CODE, |
| (BIT(29) | BIT(27))); |
| setbits_le32(®s->sdcc_hc_ddr_config, |
| SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY); |
| setbits_le32(®s->sdcc_hc_ddr_config, |
| SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_EN); |
| |
| setbits_le32(®s->io_macro_config, RGMII_CONFIG_LOOPBACK_EN); |
| break; |
| |
| default: |
| dev_err(dev, "Invalid speed %ld\n", speed); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static int ethqos_configure(struct udevice *dev, |
| struct dwmac_rgmii_regs *regs, |
| unsigned long speed) |
| { |
| unsigned int retry = 1000; |
| |
| /* Reset to POR values and enable clk */ |
| writel(emac_v2_3_0_por.io_macro_config, ®s->io_macro_config); |
| writel(emac_v2_3_0_por.sdcc_hc_dll_config, ®s->sdcc_hc_dll_config); |
| writel(emac_v2_3_0_por.sdcc_hc_ddr_config, ®s->sdcc_hc_ddr_config); |
| writel(emac_v2_3_0_por.sdcc_hc_dll_config2, ®s->sdcc_hc_dll_config2); |
| writel(emac_v2_3_0_por.sdcc_usr_ctl, ®s->sdcc_usr_ctl); |
| writel(emac_v2_3_0_por.io_macro_config2, ®s->io_macro_config2); |
| |
| ethqos_set_func_clk_en(regs); |
| |
| /* Initialize the DLL first */ |
| |
| /* Set DLL_RST */ |
| setbits_le32(®s->sdcc_hc_dll_config, SDCC_DLL_CONFIG_DLL_RST); |
| |
| /* Set PDN */ |
| setbits_le32(®s->sdcc_hc_dll_config, SDCC_DLL_CONFIG_PDN); |
| |
| /* Clear DLL_RST */ |
| clrbits_le32(®s->sdcc_hc_dll_config, SDCC_DLL_CONFIG_DLL_RST); |
| |
| /* Clear PDN */ |
| clrbits_le32(®s->sdcc_hc_dll_config, SDCC_DLL_CONFIG_PDN); |
| |
| if (speed == SPEED_1000) { |
| /* Set DLL_EN */ |
| setbits_le32(®s->sdcc_hc_dll_config, SDCC_DLL_CONFIG_DLL_EN); |
| |
| /* Set CK_OUT_EN */ |
| setbits_le32(®s->sdcc_hc_dll_config, |
| SDCC_DLL_CONFIG_CK_OUT_EN); |
| |
| /* Set USR_CTL bit 26 with mask of 3 bits */ |
| clrsetbits_le32(®s->sdcc_usr_ctl, GENMASK(26, 24), BIT(26)); |
| |
| /* wait for DLL LOCK */ |
| do { |
| mdelay(1); |
| if (readl(®s->sdc4_status) & SDC4_STATUS_DLL_LOCK) |
| break; |
| retry--; |
| } while (retry > 0); |
| if (!retry) |
| dev_err(dev, "Timeout while waiting for DLL lock\n"); |
| |
| ethqos_dll_configure(dev, regs); |
| } |
| |
| ethqos_rgmii_macro_init(dev, regs, speed); |
| |
| return 0; |
| } |
| |
| static void ethqos_rgmii_dump(struct udevice *dev, |
| struct dwmac_rgmii_regs *regs) |
| { |
| dev_dbg(dev, "Rgmii register dump\n"); |
| dev_dbg(dev, "RGMII_IO_MACRO_CONFIG: %08x\n", |
| readl(®s->io_macro_config)); |
| dev_dbg(dev, "SDCC_HC_REG_DLL_CONFIG: %08x\n", |
| readl(®s->sdcc_hc_dll_config)); |
| dev_dbg(dev, "SDCC_HC_REG_DDR_CONFIG: %08x\n", |
| readl(®s->sdcc_hc_ddr_config)); |
| dev_dbg(dev, "SDCC_HC_REG_DLL_CONFIG2: %08x\n", |
| readl(®s->sdcc_hc_dll_config2)); |
| dev_dbg(dev, "SDC4_STATUS: %08x\n", |
| readl(®s->sdc4_status)); |
| dev_dbg(dev, "SDCC_USR_CTL: %08x\n", |
| readl(®s->sdcc_usr_ctl)); |
| dev_dbg(dev, "RGMII_IO_MACRO_CONFIG2: %08x\n", |
| readl(®s->io_macro_config2)); |
| dev_dbg(dev, "RGMII_IO_MACRO_DEBUG1: %08x\n", |
| readl(®s->io_macro_debug1)); |
| dev_dbg(dev, "EMAC_SYSTEM_LOW_POWER_DEBUG: %08x\n", |
| readl(®s->emac_sys_low_power_dbg)); |
| } |
| |
| static int qcom_eqos_rgmii_set_speed(struct udevice *dev, |
| void *rgmii_regs, |
| unsigned long speed) |
| { |
| int ret; |
| |
| ethqos_rgmii_dump(dev, rgmii_regs); |
| |
| ret = ethqos_configure(dev, rgmii_regs, speed); |
| if (ret) |
| return ret; |
| |
| ethqos_rgmii_dump(dev, rgmii_regs); |
| |
| return 0; |
| } |
| |
| static int qcom_eqos_rgmii_reset(struct udevice *dev, void *rgmii_regs) |
| { |
| ethqos_set_func_clk_en(rgmii_regs); |
| |
| return 0; |
| } |
| |
| static int eqos_start_clks_qcom(struct udevice *dev) |
| { |
| if (IS_ENABLED(CONFIG_CLK)) { |
| struct clk_bulk clocks; |
| int ret; |
| |
| ret = clk_get_bulk(dev, &clocks); |
| if (ret) |
| return ret; |
| |
| ret = clk_enable_bulk(&clocks); |
| if (ret) |
| return ret; |
| } |
| |
| debug("%s: OK\n", __func__); |
| return 0; |
| } |
| |
| static int eqos_stop_clks_qcom(struct udevice *dev) |
| { |
| if (IS_ENABLED(CONFIG_CLK)) { |
| struct clk_bulk clocks; |
| int ret; |
| |
| ret = clk_get_bulk(dev, &clocks); |
| if (ret) |
| return ret; |
| |
| ret = clk_disable_bulk(&clocks); |
| if (ret) |
| return ret; |
| } |
| |
| debug("%s: OK\n", __func__); |
| return 0; |
| } |
| |
| static int eqos_start_resets_qcom(struct udevice *dev) |
| { |
| struct eqos_priv *eqos = dev_get_priv(dev); |
| int ret; |
| |
| debug("%s(dev=%p):\n", __func__, dev); |
| |
| if (!eqos->phy) { |
| ret = dm_gpio_set_value(&eqos->phy_reset_gpio, 0); |
| if (ret < 0) { |
| pr_err("dm_gpio_set_value(phy_reset, assert) failed: %d", ret); |
| return ret; |
| } |
| |
| udelay(eqos->reset_delays[0]); |
| |
| ret = dm_gpio_set_value(&eqos->phy_reset_gpio, 1); |
| if (ret < 0) { |
| pr_err("dm_gpio_set_value(phy_reset, deassert) failed: %d", ret); |
| return ret; |
| } |
| |
| udelay(eqos->reset_delays[1]); |
| |
| ret = dm_gpio_set_value(&eqos->phy_reset_gpio, 0); |
| if (ret < 0) { |
| pr_err("dm_gpio_set_value(phy_reset, deassert) failed: %d", ret); |
| return ret; |
| } |
| |
| udelay(eqos->reset_delays[2]); |
| } |
| |
| ret = reset_deassert(&eqos->reset_ctl); |
| if (ret < 0) { |
| pr_err("reset_deassert() failed: %d", ret); |
| return ret; |
| } |
| |
| ret = qcom_eqos_rgmii_reset(dev, eqos->eqos_qcom_rgmii_regs); |
| if (ret < 0) { |
| pr_err("qcom rgmii_reset failed: %d", ret); |
| return ret; |
| } |
| |
| debug("%s: OK\n", __func__); |
| return 0; |
| } |
| |
| /* Clock rates */ |
| #define RGMII_1000_NOM_CLK_FREQ (250 * 1000 * 1000UL) |
| #define RGMII_ID_MODE_100_LOW_SVS_CLK_FREQ (50 * 1000 * 1000UL) |
| #define RGMII_ID_MODE_10_LOW_SVS_CLK_FREQ (5 * 1000 * 1000UL) |
| |
| static int eqos_set_tx_clk_speed_qcom(struct udevice *dev) |
| { |
| struct eqos_priv *eqos = dev_get_priv(dev); |
| ulong rate; |
| int ret; |
| |
| debug("%s(dev=%p):\n", __func__, dev); |
| |
| switch (eqos->phy->speed) { |
| case SPEED_1000: |
| rate = RGMII_1000_NOM_CLK_FREQ; |
| break; |
| case SPEED_100: |
| rate = RGMII_ID_MODE_100_LOW_SVS_CLK_FREQ; |
| break; |
| case SPEED_10: |
| rate = RGMII_ID_MODE_10_LOW_SVS_CLK_FREQ; |
| break; |
| default: |
| pr_err("invalid speed %d", eqos->phy->speed); |
| return -EINVAL; |
| } |
| |
| ret = clk_set_rate(&eqos->clk_tx, rate); |
| if (ret < 0) { |
| pr_err("clk_set_rate(tx_clk, %lu) failed: %d", rate, ret); |
| return ret; |
| } |
| |
| ret = qcom_eqos_rgmii_set_speed(dev, eqos->eqos_qcom_rgmii_regs, |
| eqos->phy->speed); |
| if (ret < 0) { |
| pr_err("qcom set_speed: %d, failed: %d", eqos->phy->speed, ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int eqos_probe_resources_qcom(struct udevice *dev) |
| { |
| struct eqos_priv *eqos = dev_get_priv(dev); |
| phy_interface_t interface; |
| int reset_flags = GPIOD_IS_OUT; |
| int ret; |
| |
| debug("%s(dev=%p):\n", __func__, dev); |
| |
| interface = eqos->config->interface(dev); |
| |
| if (interface == PHY_INTERFACE_MODE_NA) { |
| pr_err("Invalid PHY interface\n"); |
| return -EINVAL; |
| } |
| |
| eqos->max_speed = dev_read_u32_default(dev, "max-speed", 0); |
| |
| eqos->tx_fifo_sz = dev_read_u32_default(dev, "tx-fifo-depth", 0); |
| eqos->rx_fifo_sz = dev_read_u32_default(dev, "rx-fifo-depth", 0); |
| |
| ret = reset_get_by_name(dev, "emac", &eqos->reset_ctl); |
| if (ret) { |
| pr_err("reset_get_by_name(rst) failed: %d", ret); |
| return ret; |
| } |
| |
| if (dev_read_bool(dev, "snps,reset-active-low")) |
| reset_flags |= GPIOD_ACTIVE_LOW; |
| |
| ret = gpio_request_by_name(dev, "snps,reset-gpio", 0, |
| &eqos->phy_reset_gpio, reset_flags); |
| if (ret == 0) { |
| ret = dev_read_u32_array(dev, "snps,reset-delays-us", |
| eqos->reset_delays, 3); |
| } else if (ret == -ENOENT) { |
| ret = 0; |
| } |
| |
| eqos->eqos_qcom_rgmii_regs = (void *)dev_read_addr_name(dev, "rgmii"); |
| if ((fdt_addr_t)eqos->eqos_qcom_rgmii_regs == FDT_ADDR_T_NONE) { |
| pr_err("Invalid RGMII address\n"); |
| return -EINVAL; |
| } |
| |
| ret = clk_get_by_name(dev, "rgmii", &eqos->clk_tx); |
| if (ret) { |
| pr_err("clk_get_by_name(tx) failed: %d", ret); |
| return -EINVAL; |
| } |
| |
| debug("%s: OK\n", __func__); |
| return 0; |
| } |
| |
| static int eqos_remove_resources_qcom(struct udevice *dev) |
| { |
| struct eqos_priv *eqos = dev_get_priv(dev); |
| |
| debug("%s(dev=%p):\n", __func__, dev); |
| |
| dm_gpio_free(dev, &eqos->phy_reset_gpio); |
| reset_free(&eqos->reset_ctl); |
| |
| debug("%s: OK\n", __func__); |
| return 0; |
| } |
| |
| static struct eqos_ops eqos_qcom_ops = { |
| .eqos_inval_desc = eqos_inval_desc_generic, |
| .eqos_flush_desc = eqos_flush_desc_generic, |
| .eqos_inval_buffer = eqos_inval_buffer_generic, |
| .eqos_flush_buffer = eqos_flush_buffer_generic, |
| .eqos_probe_resources = eqos_probe_resources_qcom, |
| .eqos_remove_resources = eqos_remove_resources_qcom, |
| .eqos_stop_resets = eqos_null_ops, |
| .eqos_start_resets = eqos_start_resets_qcom, |
| .eqos_stop_clks = eqos_stop_clks_qcom, |
| .eqos_start_clks = eqos_start_clks_qcom, |
| .eqos_calibrate_pads = eqos_null_ops, |
| .eqos_disable_calibration = eqos_null_ops, |
| .eqos_set_tx_clk_speed = eqos_set_tx_clk_speed_qcom, |
| .eqos_get_enetaddr = eqos_null_ops, |
| }; |
| |
| struct eqos_config __maybe_unused eqos_qcom_config = { |
| .reg_access_always_ok = false, |
| .mdio_wait = 10, |
| .swr_wait = 50, |
| .config_mac = EQOS_MAC_RXQ_CTRL0_RXQ0EN_ENABLED_DCB, |
| .config_mac_mdio = EQOS_MAC_MDIO_ADDRESS_CR_250_300, |
| .axi_bus_width = EQOS_AXI_WIDTH_64, |
| .interface = dev_read_phy_mode, |
| .ops = &eqos_qcom_ops |
| }; |