| // SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) |
| /* |
| * Device Tree Source for the R9A08G045S33 SMARC Carrier-II's SoM board. |
| * |
| * Copyright (C) 2023 Renesas Electronics Corp. |
| */ |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/pinctrl/rzg2l-pinctrl.h> |
| |
| /* |
| * Signals of SW_CONFIG switches: |
| * @SW_SD0_DEV_SEL: |
| * 0 - SD0 is connected to eMMC |
| * 1 - SD0 is connected to uSD0 card |
| */ |
| #define SW_SD0_DEV_SEL 1 |
| |
| / { |
| compatible = "renesas,rzg3s-smarcm", "renesas,r9a08g045s33", "renesas,r9a08g045"; |
| |
| aliases { |
| mmc0 = &sdhi0; |
| }; |
| |
| chosen { |
| bootargs = "ignore_loglevel"; |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| memory@48000000 { |
| device_type = "memory"; |
| /* First 128MB is reserved for secure area. */ |
| reg = <0x0 0x48000000 0x0 0x38000000>; |
| }; |
| |
| vcc_sdhi0: regulator0 { |
| compatible = "regulator-fixed"; |
| regulator-name = "SDHI0 Vcc"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpios = <&pinctrl RZG2L_GPIO(2, 1) GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| #if SW_SD0_DEV_SEL |
| vccq_sdhi0: regulator1 { |
| compatible = "regulator-gpio"; |
| regulator-name = "SDHI0 VccQ"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| gpios = <&pinctrl RZG2L_GPIO(2, 2) GPIO_ACTIVE_HIGH>; |
| gpios-states = <1>; |
| states = <3300000 1>, <1800000 0>; |
| }; |
| #else |
| reg_1p8v: regulator1 { |
| compatible = "regulator-fixed"; |
| regulator-name = "fixed-1.8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| #endif |
| }; |
| |
| &extal_clk { |
| clock-frequency = <24000000>; |
| }; |
| |
| #if SW_SD0_DEV_SEL |
| /* SD0 slot */ |
| &sdhi0 { |
| pinctrl-0 = <&sdhi0_pins>; |
| pinctrl-1 = <&sdhi0_uhs_pins>; |
| pinctrl-names = "default", "state_uhs"; |
| vmmc-supply = <&vcc_sdhi0>; |
| vqmmc-supply = <&vccq_sdhi0>; |
| bus-width = <4>; |
| sd-uhs-sdr50; |
| sd-uhs-sdr104; |
| max-frequency = <125000000>; |
| status = "okay"; |
| }; |
| #else |
| /* eMMC */ |
| &sdhi0 { |
| pinctrl-0 = <&sdhi0_emmc_pins>; |
| pinctrl-1 = <&sdhi0_emmc_pins>; |
| pinctrl-names = "default", "state_uhs"; |
| vmmc-supply = <&vcc_sdhi0>; |
| vqmmc-supply = <®_1p8v>; |
| bus-width = <8>; |
| mmc-hs200-1_8v; |
| non-removable; |
| fixed-emmc-driver-type = <1>; |
| max-frequency = <125000000>; |
| status = "okay"; |
| }; |
| #endif |
| |
| &pinctrl { |
| sdhi0_pins: sd0 { |
| data { |
| pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3"; |
| power-source = <3300>; |
| }; |
| |
| ctrl { |
| pins = "SD0_CLK", "SD0_CMD"; |
| power-source = <3300>; |
| }; |
| |
| cd { |
| pinmux = <RZG2L_PORT_PINMUX(0, 0, 1)>; /* SD0_CD */ |
| }; |
| }; |
| |
| sdhi0_uhs_pins: sd0-uhs { |
| data { |
| pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3"; |
| power-source = <1800>; |
| }; |
| |
| ctrl { |
| pins = "SD0_CLK", "SD0_CMD"; |
| power-source = <1800>; |
| }; |
| |
| cd { |
| pinmux = <RZG2L_PORT_PINMUX(0, 0, 1)>; /* SD0_CD */ |
| }; |
| }; |
| |
| sdhi0_emmc_pins: sd0-emmc { |
| pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3", |
| "SD0_DATA4", "SD0_DATA5", "SD0_DATA6", "SD0_DATA7", |
| "SD0_CLK", "SD0_CMD", "SD0_RST#"; |
| power-source = <1800>; |
| }; |
| }; |