| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Copyright Altera Corporation (C) 2015. All rights reserved. |
| */ |
| |
| /dts-v1/; |
| #include <dt-bindings/reset/altr,rst-mgr-s10.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/clock/stratix10-clock.h> |
| |
| / { |
| compatible = "altr,socfpga-stratix10"; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| reserved-memory { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| service_reserved: svcbuffer@0 { |
| compatible = "shared-dma-pool"; |
| reg = <0x0 0x0 0x0 0x1000000>; |
| alignment = <0x1000>; |
| no-map; |
| }; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu0: cpu@0 { |
| compatible = "arm,cortex-a53"; |
| device_type = "cpu"; |
| enable-method = "psci"; |
| reg = <0x0>; |
| }; |
| |
| cpu1: cpu@1 { |
| compatible = "arm,cortex-a53"; |
| device_type = "cpu"; |
| enable-method = "psci"; |
| reg = <0x1>; |
| }; |
| |
| cpu2: cpu@2 { |
| compatible = "arm,cortex-a53"; |
| device_type = "cpu"; |
| enable-method = "psci"; |
| reg = <0x2>; |
| }; |
| |
| cpu3: cpu@3 { |
| compatible = "arm,cortex-a53"; |
| device_type = "cpu"; |
| enable-method = "psci"; |
| reg = <0x3>; |
| }; |
| }; |
| |
| pmu { |
| compatible = "arm,armv8-pmuv3"; |
| interrupts = <0 170 4>, |
| <0 171 4>, |
| <0 172 4>, |
| <0 173 4>; |
| interrupt-affinity = <&cpu0>, |
| <&cpu1>, |
| <&cpu2>, |
| <&cpu3>; |
| interrupt-parent = <&intc>; |
| }; |
| |
| psci { |
| compatible = "arm,psci-0.2"; |
| method = "smc"; |
| }; |
| |
| /* Local timer */ |
| timer { |
| compatible = "arm,armv8-timer"; |
| interrupts = <1 13 0xf08>, |
| <1 14 0xf08>, |
| <1 11 0xf08>, |
| <1 10 0xf08>; |
| interrupt-parent = <&intc>; |
| }; |
| |
| intc: interrupt-controller@fffc1000 { |
| compatible = "arm,gic-400", "arm,cortex-a15-gic"; |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| reg = <0x0 0xfffc1000 0x0 0x1000>, |
| <0x0 0xfffc2000 0x0 0x2000>, |
| <0x0 0xfffc4000 0x0 0x2000>, |
| <0x0 0xfffc6000 0x0 0x2000>; |
| }; |
| |
| clocks { |
| cb_intosc_hs_div2_clk: cb-intosc-hs-div2-clk { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| }; |
| |
| cb_intosc_ls_clk: cb-intosc-ls-clk { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| }; |
| |
| f2s_free_clk: f2s-free-clk { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| }; |
| |
| osc1: osc1 { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| }; |
| |
| qspi_clk: qspi-clk { |
| #clock-cells = <0>; |
| compatible = "fixed-clock"; |
| clock-frequency = <200000000>; |
| }; |
| }; |
| |
| soc { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "simple-bus"; |
| device_type = "soc"; |
| interrupt-parent = <&intc>; |
| ranges = <0 0 0 0xffffffff>; |
| |
| base_fpga_region { |
| #address-cells = <0x2>; |
| #size-cells = <0x2>; |
| compatible = "fpga-region"; |
| fpga-mgr = <&fpga_mgr>; |
| }; |
| |
| clkmgr: clock-controller@ffd10000 { |
| compatible = "intel,stratix10-clkmgr"; |
| reg = <0xffd10000 0x1000>; |
| #clock-cells = <1>; |
| }; |
| |
| gmac0: ethernet@ff800000 { |
| compatible = "altr,socfpga-stmmac-a10-s10", "snps,dwmac-3.74a", "snps,dwmac"; |
| reg = <0xff800000 0x2000>; |
| interrupts = <0 90 4>; |
| interrupt-names = "macirq"; |
| mac-address = [00 00 00 00 00 00]; |
| resets = <&rst EMAC0_RESET>, <&rst EMAC0_OCP_RESET>; |
| reset-names = "stmmaceth", "ahb"; |
| clocks = <&clkmgr STRATIX10_EMAC0_CLK>, <&clkmgr STRATIX10_EMAC_PTP_CLK>; |
| clock-names = "stmmaceth", "ptp_ref"; |
| tx-fifo-depth = <16384>; |
| rx-fifo-depth = <16384>; |
| snps,multicast-filter-bins = <256>; |
| iommus = <&smmu 1>; |
| altr,sysmgr-syscon = <&sysmgr 0x44 0>; |
| status = "disabled"; |
| }; |
| |
| gmac1: ethernet@ff802000 { |
| compatible = "altr,socfpga-stmmac-a10-s10", "snps,dwmac-3.74a", "snps,dwmac"; |
| reg = <0xff802000 0x2000>; |
| interrupts = <0 91 4>; |
| interrupt-names = "macirq"; |
| mac-address = [00 00 00 00 00 00]; |
| resets = <&rst EMAC1_RESET>, <&rst EMAC1_OCP_RESET>; |
| reset-names = "stmmaceth", "ahb"; |
| clocks = <&clkmgr STRATIX10_EMAC1_CLK>, <&clkmgr STRATIX10_EMAC_PTP_CLK>; |
| clock-names = "stmmaceth", "ptp_ref"; |
| tx-fifo-depth = <16384>; |
| rx-fifo-depth = <16384>; |
| snps,multicast-filter-bins = <256>; |
| iommus = <&smmu 2>; |
| altr,sysmgr-syscon = <&sysmgr 0x48 8>; |
| status = "disabled"; |
| }; |
| |
| gmac2: ethernet@ff804000 { |
| compatible = "altr,socfpga-stmmac-a10-s10", "snps,dwmac-3.74a", "snps,dwmac"; |
| reg = <0xff804000 0x2000>; |
| interrupts = <0 92 4>; |
| interrupt-names = "macirq"; |
| mac-address = [00 00 00 00 00 00]; |
| resets = <&rst EMAC2_RESET>, <&rst EMAC2_OCP_RESET>; |
| reset-names = "stmmaceth", "ahb"; |
| clocks = <&clkmgr STRATIX10_EMAC2_CLK>, <&clkmgr STRATIX10_EMAC_PTP_CLK>; |
| clock-names = "stmmaceth", "ptp_ref"; |
| tx-fifo-depth = <16384>; |
| rx-fifo-depth = <16384>; |
| snps,multicast-filter-bins = <256>; |
| iommus = <&smmu 3>; |
| altr,sysmgr-syscon = <&sysmgr 0x4c 16>; |
| status = "disabled"; |
| }; |
| |
| gpio0: gpio@ffc03200 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "snps,dw-apb-gpio"; |
| reg = <0xffc03200 0x100>; |
| resets = <&rst GPIO0_RESET>; |
| status = "disabled"; |
| |
| porta: gpio-controller@0 { |
| compatible = "snps,dw-apb-gpio-port"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| ngpios = <24>; |
| reg = <0>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| interrupts = <0 110 4>; |
| }; |
| }; |
| |
| gpio1: gpio@ffc03300 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "snps,dw-apb-gpio"; |
| reg = <0xffc03300 0x100>; |
| resets = <&rst GPIO1_RESET>; |
| status = "disabled"; |
| |
| portb: gpio-controller@0 { |
| compatible = "snps,dw-apb-gpio-port"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| ngpios = <24>; |
| reg = <0>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| interrupts = <0 111 4>; |
| }; |
| }; |
| |
| i2c0: i2c@ffc02800 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "snps,designware-i2c"; |
| reg = <0xffc02800 0x100>; |
| interrupts = <0 103 4>; |
| resets = <&rst I2C0_RESET>; |
| clocks = <&clkmgr STRATIX10_L4_SP_CLK>; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@ffc02900 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "snps,designware-i2c"; |
| reg = <0xffc02900 0x100>; |
| interrupts = <0 104 4>; |
| resets = <&rst I2C1_RESET>; |
| clocks = <&clkmgr STRATIX10_L4_SP_CLK>; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@ffc02a00 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "snps,designware-i2c"; |
| reg = <0xffc02a00 0x100>; |
| interrupts = <0 105 4>; |
| resets = <&rst I2C2_RESET>; |
| clocks = <&clkmgr STRATIX10_L4_SP_CLK>; |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@ffc02b00 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "snps,designware-i2c"; |
| reg = <0xffc02b00 0x100>; |
| interrupts = <0 106 4>; |
| resets = <&rst I2C3_RESET>; |
| clocks = <&clkmgr STRATIX10_L4_SP_CLK>; |
| status = "disabled"; |
| }; |
| |
| i2c4: i2c@ffc02c00 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "snps,designware-i2c"; |
| reg = <0xffc02c00 0x100>; |
| interrupts = <0 107 4>; |
| resets = <&rst I2C4_RESET>; |
| clocks = <&clkmgr STRATIX10_L4_SP_CLK>; |
| status = "disabled"; |
| }; |
| |
| mmc: mmc@ff808000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "altr,socfpga-dw-mshc"; |
| reg = <0xff808000 0x1000>; |
| interrupts = <0 96 4>; |
| fifo-depth = <0x400>; |
| resets = <&rst SDMMC_RESET>; |
| reset-names = "reset"; |
| clocks = <&clkmgr STRATIX10_L4_MP_CLK>, |
| <&clkmgr STRATIX10_SDMMC_CLK>; |
| clock-names = "biu", "ciu"; |
| iommus = <&smmu 5>; |
| altr,sysmgr-syscon = <&sysmgr 0x28 4>; |
| status = "disabled"; |
| }; |
| |
| nand: nand-controller@ffb90000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "altr,socfpga-denali-nand"; |
| reg = <0xffb90000 0x10000>, |
| <0xffb80000 0x1000>; |
| reg-names = "nand_data", "denali_reg"; |
| interrupts = <0 97 4>; |
| clocks = <&clkmgr STRATIX10_NAND_CLK>, |
| <&clkmgr STRATIX10_NAND_X_CLK>, |
| <&clkmgr STRATIX10_NAND_ECC_CLK>; |
| clock-names = "nand", "nand_x", "ecc"; |
| resets = <&rst NAND_RESET>, <&rst NAND_OCP_RESET>; |
| status = "disabled"; |
| }; |
| |
| ocram: sram@ffe00000 { |
| compatible = "mmio-sram"; |
| reg = <0xffe00000 0x100000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0xffe00000 0x100000>; |
| }; |
| |
| pdma: dma-controller@ffda0000 { |
| compatible = "arm,pl330", "arm,primecell"; |
| reg = <0xffda0000 0x1000>; |
| interrupts = <0 81 4>, |
| <0 82 4>, |
| <0 83 4>, |
| <0 84 4>, |
| <0 85 4>, |
| <0 86 4>, |
| <0 87 4>, |
| <0 88 4>, |
| <0 89 4>; |
| #dma-cells = <1>; |
| clocks = <&clkmgr STRATIX10_L4_MAIN_CLK>; |
| clock-names = "apb_pclk"; |
| resets = <&rst DMA_RESET>, <&rst DMA_OCP_RESET>; |
| reset-names = "dma", "dma-ocp"; |
| }; |
| |
| pinctrl0: pinctrl@ffd13000 { |
| compatible = "pinctrl-single"; |
| reg = <0xffd13000 0xA0>; |
| #pinctrl-cells = <1>; |
| pinctrl-single,register-width = <32>; |
| pinctrl-single,function-mask = <0x0000000f>; |
| }; |
| |
| pinctrl1: pinctrl@ffd13100 { |
| compatible = "pinctrl-single"; |
| reg = <0xffd13100 0x20>; |
| #pinctrl-cells = <1>; |
| pinctrl-single,register-width = <32>; |
| pinctrl-single,function-mask = <0x0000000f>; |
| }; |
| |
| rst: rstmgr@ffd11000 { |
| #reset-cells = <1>; |
| compatible = "altr,stratix10-rst-mgr"; |
| reg = <0xffd11000 0x1000>; |
| }; |
| |
| smmu: iommu@fa000000 { |
| compatible = "arm,mmu-500", "arm,smmu-v2"; |
| reg = <0xfa000000 0x40000>; |
| #global-interrupts = <2>; |
| #iommu-cells = <1>; |
| clocks = <&clkmgr STRATIX10_L4_MAIN_CLK>; |
| clock-names = "iommu"; |
| interrupt-parent = <&intc>; |
| interrupts = <0 128 4>, /* Global Secure Fault */ |
| <0 129 4>, /* Global Non-secure Fault */ |
| /* Non-secure Context Interrupts (32) */ |
| <0 138 4>, <0 139 4>, <0 140 4>, <0 141 4>, |
| <0 142 4>, <0 143 4>, <0 144 4>, <0 145 4>, |
| <0 146 4>, <0 147 4>, <0 148 4>, <0 149 4>, |
| <0 150 4>, <0 151 4>, <0 152 4>, <0 153 4>, |
| <0 154 4>, <0 155 4>, <0 156 4>, <0 157 4>, |
| <0 158 4>, <0 159 4>, <0 160 4>, <0 161 4>, |
| <0 162 4>, <0 163 4>, <0 164 4>, <0 165 4>, |
| <0 166 4>, <0 167 4>, <0 168 4>, <0 169 4>; |
| stream-match-mask = <0x7ff0>; |
| status = "disabled"; |
| }; |
| |
| spi0: spi@ffda4000 { |
| compatible = "snps,dw-apb-ssi"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0xffda4000 0x1000>; |
| interrupts = <0 99 4>; |
| resets = <&rst SPIM0_RESET>; |
| reset-names = "spi"; |
| reg-io-width = <4>; |
| num-cs = <4>; |
| clocks = <&clkmgr STRATIX10_L4_MAIN_CLK>; |
| status = "disabled"; |
| }; |
| |
| spi1: spi@ffda5000 { |
| compatible = "snps,dw-apb-ssi"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0xffda5000 0x1000>; |
| interrupts = <0 100 4>; |
| resets = <&rst SPIM1_RESET>; |
| reset-names = "spi"; |
| reg-io-width = <4>; |
| num-cs = <4>; |
| clocks = <&clkmgr STRATIX10_L4_MAIN_CLK>; |
| status = "disabled"; |
| }; |
| |
| sysmgr: sysmgr@ffd12000 { |
| compatible = "altr,sys-mgr-s10","altr,sys-mgr"; |
| reg = <0xffd12000 0x228>; |
| }; |
| |
| timer0: timer0@ffc03000 { |
| compatible = "snps,dw-apb-timer"; |
| interrupts = <0 113 4>; |
| reg = <0xffc03000 0x100>; |
| clocks = <&clkmgr STRATIX10_L4_SP_CLK>; |
| clock-names = "timer"; |
| }; |
| |
| timer1: timer1@ffc03100 { |
| compatible = "snps,dw-apb-timer"; |
| interrupts = <0 114 4>; |
| reg = <0xffc03100 0x100>; |
| clocks = <&clkmgr STRATIX10_L4_SP_CLK>; |
| clock-names = "timer"; |
| }; |
| |
| timer2: timer2@ffd00000 { |
| compatible = "snps,dw-apb-timer"; |
| interrupts = <0 115 4>; |
| reg = <0xffd00000 0x100>; |
| clocks = <&clkmgr STRATIX10_L4_SP_CLK>; |
| clock-names = "timer"; |
| }; |
| |
| timer3: timer3@ffd00100 { |
| compatible = "snps,dw-apb-timer"; |
| interrupts = <0 116 4>; |
| reg = <0xffd00100 0x100>; |
| clocks = <&clkmgr STRATIX10_L4_SP_CLK>; |
| clock-names = "timer"; |
| }; |
| |
| uart0: serial@ffc02000 { |
| compatible = "snps,dw-apb-uart"; |
| reg = <0xffc02000 0x100>; |
| interrupts = <0 108 4>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| resets = <&rst UART0_RESET>; |
| clocks = <&clkmgr STRATIX10_L4_SP_CLK>; |
| status = "disabled"; |
| }; |
| |
| uart1: serial@ffc02100 { |
| compatible = "snps,dw-apb-uart"; |
| reg = <0xffc02100 0x100>; |
| interrupts = <0 109 4>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| resets = <&rst UART1_RESET>; |
| clocks = <&clkmgr STRATIX10_L4_SP_CLK>; |
| status = "disabled"; |
| }; |
| |
| usb0: usb@ffb00000 { |
| compatible = "snps,dwc2"; |
| reg = <0xffb00000 0x40000>; |
| interrupts = <0 93 4>; |
| phys = <&usbphy0>; |
| phy-names = "usb2-phy"; |
| resets = <&rst USB0_RESET>, <&rst USB0_OCP_RESET>; |
| reset-names = "dwc2", "dwc2-ecc"; |
| clocks = <&clkmgr STRATIX10_USB_CLK>; |
| clock-names = "otg"; |
| iommus = <&smmu 6>; |
| status = "disabled"; |
| }; |
| |
| usb1: usb@ffb40000 { |
| compatible = "snps,dwc2"; |
| reg = <0xffb40000 0x40000>; |
| interrupts = <0 94 4>; |
| phys = <&usbphy0>; |
| phy-names = "usb2-phy"; |
| resets = <&rst USB1_RESET>, <&rst USB1_OCP_RESET>; |
| reset-names = "dwc2", "dwc2-ecc"; |
| clocks = <&clkmgr STRATIX10_USB_CLK>; |
| iommus = <&smmu 7>; |
| status = "disabled"; |
| }; |
| |
| watchdog0: watchdog@ffd00200 { |
| compatible = "snps,dw-wdt"; |
| reg = <0xffd00200 0x100>; |
| interrupts = <0 117 4>; |
| resets = <&rst WATCHDOG0_RESET>; |
| clocks = <&clkmgr STRATIX10_L4_SYS_FREE_CLK>; |
| status = "disabled"; |
| }; |
| |
| watchdog1: watchdog@ffd00300 { |
| compatible = "snps,dw-wdt"; |
| reg = <0xffd00300 0x100>; |
| interrupts = <0 118 4>; |
| resets = <&rst WATCHDOG1_RESET>; |
| clocks = <&clkmgr STRATIX10_L4_SYS_FREE_CLK>; |
| status = "disabled"; |
| }; |
| |
| watchdog2: watchdog@ffd00400 { |
| compatible = "snps,dw-wdt"; |
| reg = <0xffd00400 0x100>; |
| interrupts = <0 125 4>; |
| resets = <&rst WATCHDOG2_RESET>; |
| clocks = <&clkmgr STRATIX10_L4_SYS_FREE_CLK>; |
| status = "disabled"; |
| }; |
| |
| watchdog3: watchdog@ffd00500 { |
| compatible = "snps,dw-wdt"; |
| reg = <0xffd00500 0x100>; |
| interrupts = <0 126 4>; |
| resets = <&rst WATCHDOG3_RESET>; |
| clocks = <&clkmgr STRATIX10_L4_SYS_FREE_CLK>; |
| status = "disabled"; |
| }; |
| |
| sdr: sdr@f8011100 { |
| compatible = "altr,sdr-ctl", "syscon"; |
| reg = <0xf8011100 0xc0>; |
| }; |
| |
| eccmgr { |
| compatible = "altr,socfpga-s10-ecc-manager", |
| "altr,socfpga-a10-ecc-manager"; |
| altr,sysmgr-syscon = <&sysmgr>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| interrupts = <0 15 4>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| ranges; |
| |
| sdramedac { |
| compatible = "altr,sdram-edac-s10"; |
| altr,sdr-syscon = <&sdr>; |
| interrupts = <16 4>; |
| }; |
| |
| ocram-ecc@ff8cc000 { |
| compatible = "altr,socfpga-s10-ocram-ecc", |
| "altr,socfpga-a10-ocram-ecc"; |
| reg = <0xff8cc000 0x100>; |
| altr,ecc-parent = <&ocram>; |
| interrupts = <1 4>; |
| }; |
| |
| usb0-ecc@ff8c4000 { |
| compatible = "altr,socfpga-s10-usb-ecc", |
| "altr,socfpga-usb-ecc"; |
| reg = <0xff8c4000 0x100>; |
| altr,ecc-parent = <&usb0>; |
| interrupts = <2 4>; |
| }; |
| |
| emac0-rx-ecc@ff8c0000 { |
| compatible = "altr,socfpga-s10-eth-mac-ecc", |
| "altr,socfpga-eth-mac-ecc"; |
| reg = <0xff8c0000 0x100>; |
| altr,ecc-parent = <&gmac0>; |
| interrupts = <4 4>; |
| }; |
| |
| emac0-tx-ecc@ff8c0400 { |
| compatible = "altr,socfpga-s10-eth-mac-ecc", |
| "altr,socfpga-eth-mac-ecc"; |
| reg = <0xff8c0400 0x100>; |
| altr,ecc-parent = <&gmac0>; |
| interrupts = <5 4>; |
| }; |
| |
| }; |
| |
| qspi: spi@ff8d2000 { |
| compatible = "intel,socfpga-qspi", "cdns,qspi-nor"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0xff8d2000 0x100>, |
| <0xff900000 0x100000>; |
| interrupts = <0 3 4>; |
| cdns,fifo-depth = <128>; |
| cdns,fifo-width = <4>; |
| cdns,trigger-address = <0x00000000>; |
| clocks = <&qspi_clk>; |
| |
| status = "disabled"; |
| }; |
| |
| firmware { |
| svc { |
| compatible = "intel,stratix10-svc"; |
| method = "smc"; |
| memory-region = <&service_reserved>; |
| |
| fpga_mgr: fpga-mgr { |
| compatible = "intel,stratix10-soc-fpga-mgr"; |
| }; |
| }; |
| }; |
| }; |
| |
| usbphy0: usbphy0 { |
| compatible = "usb-nop-xceiv"; |
| #phy-cells = <0>; |
| }; |
| }; |