| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Samsung's Exynos4212 based Galaxy Tab 3 board common source |
| * |
| * Copyright (c) 2013 Samsung Electronics Co., Ltd. |
| * http://www.samsung.com |
| */ |
| |
| /dts-v1/; |
| #include "exynos4212.dtsi" |
| #include "exynos4412-ppmu-common.dtsi" |
| #include "exynos-mfc-reserved-memory.dtsi" |
| #include <dt-bindings/clock/samsung,s2mps11.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/leds/common.h> |
| #include <dt-bindings/input/gpio-keys.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include "exynos-pinctrl.h" |
| |
| / { |
| compatible = "samsung,tab3", "samsung,exynos4212", "samsung,exynos4"; |
| |
| memory@40000000 { |
| device_type = "memory"; |
| |
| /* |
| * Technically 1.5GB is available, but the latter 512MB is handled |
| * in a special way by downstream (every second page is skipped), |
| * and thus doesn't initialize correctly on mainline. Only 1020M is |
| * used for now. |
| */ |
| reg = <0x40000000 0x3fc00000>; |
| }; |
| |
| aliases { |
| mmc0 = &mshc_0; /* Internal storage */ |
| mmc1 = &sdhci_2; /* SD card */ |
| mmc2 = &sdhci_3; /* WiFi */ |
| }; |
| |
| chosen { |
| stdout-path = &serial_2; |
| |
| /* Default S-BOOT bootloader loads initramfs here */ |
| linux,initrd-start = <0x42000000>; |
| linux,initrd-end = <0x42800000>; |
| }; |
| |
| firmware@204f000 { |
| compatible = "samsung,secure-firmware"; |
| reg = <0x0204F000 0x1000>; |
| }; |
| |
| fixed-rate-clocks { |
| xxti { |
| compatible = "samsung,clock-xxti"; |
| clock-frequency = <0>; |
| }; |
| |
| xusbxti { |
| compatible = "samsung,clock-xusbxti"; |
| clock-frequency = <24000000>; |
| }; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gpio_keys>; |
| |
| key-power { |
| gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_POWER>; |
| label = "power"; |
| debounce-interval = <10>; |
| wakeup-source; |
| }; |
| |
| key-up { |
| gpios = <&gpx2 2 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEUP>; |
| label = "volume down"; |
| debounce-interval = <10>; |
| }; |
| |
| key-down { |
| gpios = <&gpx3 3 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEDOWN>; |
| label = "volume up"; |
| debounce-interval = <10>; |
| }; |
| |
| key-home { |
| gpios = <&gpx1 2 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_HOME>; |
| label = "home"; |
| debounce-interval = <10>; |
| }; |
| |
| switch-hall-sensor { |
| gpios = <&gpx2 4 GPIO_ACTIVE_LOW>; |
| linux,input-type = <EV_SW>; |
| linux,code = <SW_LID>; |
| linux,can-disable; |
| label = "hall effect sensor"; |
| debounce-interval = <10>; |
| wakeup-source; |
| }; |
| }; |
| |
| led-touchkeys { |
| compatible = "regulator-led"; |
| vled-supply = <&ldo20_reg>; |
| default-state = "off"; |
| function = LED_FUNCTION_KBD_BACKLIGHT; |
| color = <LED_COLOR_ID_WHITE>; |
| }; |
| |
| i2c_max77693: i2c-gpio-1 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&gpm2 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&gpm2 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-gpio,delay-us = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pmic@66 { |
| compatible = "maxim,max77693"; |
| reg = <0x66>; |
| interrupt-parent = <&gpx1>; |
| interrupts = <5 IRQ_TYPE_EDGE_FALLING>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&max77693_irq>; |
| |
| regulators { |
| esafeout1_reg: ESAFEOUT1 { |
| regulator-name = "ESAFEOUT1"; |
| regulator-boot-on; |
| }; |
| |
| esafeout2_reg: ESAFEOUT2 { |
| regulator-name = "ESAFEOUT2"; |
| }; |
| |
| charger_reg: CHARGER { |
| regulator-name = "CHARGER"; |
| regulator-min-microamp = <60000>; |
| regulator-max-microamp = <2580000>; |
| regulator-boot-on; |
| }; |
| }; |
| |
| charger { |
| compatible = "maxim,max77693-charger"; |
| |
| maxim,constant-microvolt = <4350000>; |
| maxim,min-system-microvolt = <3600000>; |
| maxim,thermal-regulation-celsius = <100>; |
| maxim,battery-overcurrent-microamp = <3500000>; |
| maxim,charge-input-threshold-microvolt = <4300000>; |
| }; |
| }; |
| }; |
| |
| i2c_max77693_fuel: i2c-gpio-2 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&gpy0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&gpy0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-gpio,delay-us = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| fuel-gauge@36 { |
| compatible = "maxim,max17050"; |
| reg = <0x36>; |
| interrupt-parent = <&gpx2>; |
| interrupts = <3 IRQ_TYPE_EDGE_FALLING>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&max77693_fuel_irq>; |
| |
| maxim,over-heat-temp = <500>; |
| maxim,over-volt = <4500>; |
| }; |
| }; |
| |
| i2c_magnetometer: i2c-gpio-3 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&gpy2 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&gpy2 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-gpio,delay-us = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| magnetometer@2e { |
| compatible = "yamaha,yas532"; |
| reg = <0x2e>; |
| iovdd-supply = <&ldo3_reg>; |
| mount-matrix = "-1", "0", "0", |
| "0", "1", "0", |
| "0", "0", "-1"; |
| }; |
| }; |
| |
| i2c_lightsensor: i2c-gpio-4 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&gpl0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&gpl0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| i2c-gpio,delay-us = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| |
| /* WiFi model uses CM3323, 3G/LTE use CM36653 */ |
| }; |
| |
| i2c_bl: i2c-gpio-5 { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&gpm4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&gpm4 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| backlight: backlight@2c { |
| compatible = "ti,lp8556"; |
| reg = <0x2c>; |
| |
| bl-name = "lcd-bl"; |
| dev-ctrl = /bits/ 8 <0x80>; |
| init-brt = /bits/ 8 <0x78>; /* 120 */ |
| |
| power-supply = <&vbatt_reg>; |
| enable-supply = <&backlight_reset_supply>; |
| |
| pwms = <&pwm 1 78770 0>; |
| pwm-names = "lp8556"; |
| |
| rom-a3h { |
| rom-addr = /bits/ 8 <0xa3>; |
| rom-val = /bits/ 8 <0x5e>; |
| }; |
| |
| rom-a5h { |
| rom-addr = /bits/ 8 <0xa5>; |
| rom-val = /bits/ 8 <0x34>; |
| }; |
| |
| rom-a7h { |
| rom-addr = /bits/ 8 <0xa7>; |
| rom-val = /bits/ 8 <0xfa>; |
| }; |
| }; |
| }; |
| |
| vbatt_reg: voltage-regulator-1 { |
| compatible = "regulator-fixed"; |
| regulator-name = "VBATT"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| regulator-always-on; |
| }; |
| |
| backlight_reset_supply: voltage-regulator-2 { |
| compatible = "regulator-fixed"; |
| regulator-name = "BACKLIGHT_ENVDDIO"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&backlight_reset>; |
| gpio = <&gpm0 1 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| display_3v3_supply: voltage-regulator-3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "DISPLAY_3.3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&lcd_en>; |
| gpio = <&gpc0 1 GPIO_ACTIVE_HIGH>; /* LCD_EN */ |
| enable-active-high; |
| }; |
| |
| mic_bias_reg: voltage-regulator-4 { |
| compatible = "regulator-fixed"; |
| regulator-name = "MICBIAS_LDO_2.8V"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| }; |
| |
| submic_bias_reg: voltage-regulator-5 { |
| compatible = "regulator-fixed"; |
| regulator-name = "SUB_MICBIAS_LDO_2.8V"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| }; |
| |
| sound: sound { |
| compatible = "samsung,midas-audio"; |
| model = "TAB3"; |
| mic-bias-supply = <&mic_bias_reg>; |
| submic-bias-supply = <&submic_bias_reg>; |
| |
| audio-routing = "HP", "HPOUT1L", |
| "HP", "HPOUT1R", |
| |
| "SPK", "SPKOUTLN", |
| "SPK", "SPKOUTLP", |
| "SPK", "SPKOUTRN", |
| "SPK", "SPKOUTRP", |
| |
| "RCV", "HPOUT2N", |
| "RCV", "HPOUT2P", |
| |
| "LINE", "LINEOUT2N", |
| "LINE", "LINEOUT2P", |
| |
| "HDMI", "LINEOUT1N", |
| "HDMI", "LINEOUT1P", |
| |
| "IN2LP:VXRN", "MICBIAS1", |
| "IN2LN", "MICBIAS1", |
| "Main Mic", "MICBIAS1", |
| |
| "IN1RP", "MICBIAS2", |
| "IN1RN", "MICBIAS2", |
| "Sub Mic", "MICBIAS2", |
| |
| "IN1LP", "Headset Mic", |
| "IN1LN", "Headset Mic"; |
| |
| cpu { |
| sound-dai = <&i2s0 0>; |
| }; |
| |
| codec { |
| sound-dai = <&wm1811>; |
| }; |
| }; |
| |
| wlan_pwrseq: sdhci3-pwrseq { |
| compatible = "mmc-pwrseq-simple"; |
| reset-gpios = <&gpm3 5 GPIO_ACTIVE_LOW>; |
| clocks = <&s5m8767_osc S2MPS11_CLK_BT>; |
| clock-names = "ext_clock"; |
| }; |
| }; |
| |
| &bus_acp { |
| devfreq = <&bus_dmc>; |
| status = "okay"; |
| }; |
| |
| &bus_c2c { |
| devfreq = <&bus_dmc>; |
| status = "okay"; |
| }; |
| |
| &bus_display { |
| devfreq = <&bus_leftbus>; |
| status = "okay"; |
| }; |
| |
| &bus_dmc { |
| devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>; |
| vdd-supply = <&buck1_reg>; |
| status = "okay"; |
| }; |
| |
| &bus_fsys { |
| devfreq = <&bus_leftbus>; |
| status = "okay"; |
| }; |
| |
| &bus_leftbus { |
| devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>; |
| vdd-supply = <&buck3_reg>; |
| status = "okay"; |
| }; |
| |
| &bus_mfc { |
| devfreq = <&bus_leftbus>; |
| status = "okay"; |
| }; |
| |
| &bus_peri { |
| devfreq = <&bus_leftbus>; |
| status = "okay"; |
| }; |
| |
| &bus_rightbus { |
| devfreq = <&bus_leftbus>; |
| status = "okay"; |
| }; |
| |
| &cpu0 { |
| cpu0-supply = <&buck2_reg>; |
| }; |
| |
| &cpu_thermal { |
| cooling-maps { |
| map0 { |
| /* Corresponds to 800MHz at freq_table */ |
| cooling-device = <&cpu0 7 7>, <&cpu1 7 7>; |
| }; |
| map1 { |
| /* Corresponds to 200MHz at freq_table */ |
| cooling-device = <&cpu0 13 13>, <&cpu1 13 13>; |
| }; |
| }; |
| }; |
| |
| &dsi_0 { |
| vddcore-supply = <&ldo8_reg>; |
| vddio-supply = <&ldo10_reg>; |
| samsung,burst-clock-frequency = <500000000>; |
| samsung,esc-clock-frequency = <20000000>; |
| samsung,pll-clock-frequency = <24000000>; |
| status = "okay"; |
| |
| panel@0 { |
| compatible = "samsung,lsl080al02", "samsung,s6d7aa0"; |
| reg = <0>; |
| power-supply = <&display_3v3_supply>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&lcd_nrst>; |
| reset-gpios = <&gpf0 4 GPIO_ACTIVE_LOW>; |
| backlight = <&backlight>; |
| }; |
| }; |
| |
| &exynos_usbphy { |
| vbus-supply = <&esafeout1_reg>; |
| status = "okay"; |
| }; |
| |
| &fimd { |
| status = "okay"; |
| }; |
| |
| &gpu { |
| mali-supply = <&buck4_reg>; |
| status = "okay"; |
| }; |
| |
| &hsotg { |
| vusb_d-supply = <&ldo15_reg>; |
| vusb_a-supply = <&ldo12_reg>; |
| dr_mode = "otg"; |
| status = "okay"; |
| }; |
| |
| &i2c_1 { |
| pinctrl-0 = <&i2c1_bus>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| lis3dh: accelerometer@19 { |
| /* K2DH seems to be the same as lis2dh12 in terms of registers */ |
| compatible = "st,lis2dh12-accel"; |
| reg = <0x19>; |
| |
| interrupt-parent = <&gpx0>; |
| interrupts = <0 IRQ_TYPE_EDGE_FALLING>; |
| |
| vdd-supply = <&ldo17_reg>; |
| vddio-supply = <&ldo3_reg>; |
| |
| mount-matrix = "-1", "0", "0", |
| "0", "1", "0", |
| "0", "0", "-1"; |
| }; |
| }; |
| |
| &i2c_3 { |
| samsung,i2c-sda-delay = <100>; |
| samsung,i2c-slave-addr = <0x10>; |
| samsung,i2c-max-bus-freq = <400000>; |
| pinctrl-0 = <&i2c3_bus>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| touchscreen@48 { |
| /* MELFAS MMS252, using MMS114 compatible for now */ |
| compatible = "melfas,mms114"; |
| reg = <0x48>; |
| interrupt-parent = <&gpb>; |
| interrupts = <4 IRQ_TYPE_EDGE_FALLING>; |
| touchscreen-size-x = <800>; |
| touchscreen-size-y = <1280>; |
| avdd-supply = <&ldo21_reg>; |
| vdd-supply = <&ldo25_reg>; |
| linux,keycodes = <KEY_MENU KEY_BACK>; |
| }; |
| }; |
| |
| &i2c_4 { |
| samsung,i2c-sda-delay = <100>; |
| samsung,i2c-slave-addr = <0x10>; |
| samsung,i2c-max-bus-freq = <100000>; |
| pinctrl-0 = <&i2c4_bus>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| wm1811: audio-codec@1a { |
| compatible = "wlf,wm1811"; |
| reg = <0x1a>; |
| clocks = <&pmu_system_controller 0>; |
| clock-names = "MCLK1"; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| interrupt-parent = <&gpx3>; |
| interrupts = <6 IRQ_TYPE_LEVEL_HIGH>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| #sound-dai-cells = <0>; |
| |
| wlf,gpio-cfg = <0x3 0x0 0x0 0x0 0x0 0x0 |
| 0x0 0x8000 0x0 0x0 0x0>; |
| wlf,micbias-cfg = <0x25 0x2f>; |
| |
| wlf,lineout1-feedback; |
| wlf,lineout1-se; |
| wlf,lineout2-se; |
| wlf,ldoena-always-driven; |
| |
| AVDD2-supply = <&ldo3_reg>; |
| CPVDD-supply = <&ldo3_reg>; |
| DBVDD1-supply = <&ldo3_reg>; |
| DBVDD2-supply = <&ldo3_reg>; |
| DBVDD3-supply = <&ldo3_reg>; |
| SPKVDD1-supply = <&vbatt_reg>; |
| SPKVDD2-supply = <&vbatt_reg>; |
| wlf,ldo1ena-gpios = <&gpm4 4 GPIO_ACTIVE_HIGH>; |
| wlf,ldo2ena-gpios = <&gpm4 4 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| &i2c_7 { |
| samsung,i2c-sda-delay = <100>; |
| samsung,i2c-slave-addr = <0x10>; |
| samsung,i2c-max-bus-freq = <100000>; |
| pinctrl-0 = <&i2c7_bus>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| s5m8767: pmic@66 { |
| compatible = "samsung,s5m8767-pmic"; |
| reg = <0x66>; |
| interrupt-parent = <&gpx0>; |
| interrupts = <7 IRQ_TYPE_LEVEL_LOW>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>; |
| wakeup-source; |
| |
| s5m8767,pmic-buck-default-dvs-idx = <1>; |
| |
| s5m8767,pmic-buck-dvs-gpios = <&gpm3 0 GPIO_ACTIVE_HIGH>, |
| <&gpm3 1 GPIO_ACTIVE_HIGH>, |
| <&gpm3 2 GPIO_ACTIVE_HIGH>; |
| |
| s5m8767,pmic-buck-ds-gpios = <&gpf3 1 GPIO_ACTIVE_HIGH>, |
| <&gpf3 2 GPIO_ACTIVE_HIGH>, |
| <&gpf3 3 GPIO_ACTIVE_HIGH>; |
| |
| s5m8767,pmic-buck2-dvs-voltage = <1100000>, <1100000>, |
| <1100000>, <1100000>, |
| <1100000>, <1100000>, |
| <1100000>, <1100000>; |
| |
| s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>, |
| <1100000>, <1100000>, |
| <1100000>, <1100000>, |
| <1100000>, <1100000>; |
| |
| s5m8767,pmic-buck4-dvs-voltage = <1100000>, <1100000>, |
| <1100000>, <1100000>, |
| <1100000>, <1100000>, |
| <1100000>, <1100000>; |
| |
| regulators { |
| ldo1_reg: LDO1 { |
| regulator-name = "VALIVE_1.0V_AP"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-always-on; |
| regulator-boot-on; |
| op_mode = <1>; |
| }; |
| |
| ldo2_reg: LDO2 { |
| regulator-name = "VM1M2_1.2V_AP"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-always-on; |
| regulator-boot-on; |
| op_mode = <1>; |
| }; |
| |
| ldo3_reg: LDO3 { |
| regulator-name = "VCC_1.8V_AP"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| op_mode = <1>; |
| }; |
| |
| ldo5_reg: LDO5 { |
| regulator-name = "VCC_3.3V_MHL"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| op_mode = <1>; |
| }; |
| |
| ldo8_reg: LDO8 { |
| regulator-name = "VMIPI_1.0V"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| op_mode = <3>; |
| }; |
| |
| ldo9_reg: LDO9 { |
| regulator-name = "VSIL_1.2V"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| op_mode = <1>; |
| }; |
| |
| ldo10_reg: LDO10 { |
| regulator-name = "VMIPI_1.8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| op_mode = <3>; |
| }; |
| |
| ldo12_reg: LDO12 { |
| regulator-name = "VUOTG_3.0V"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| op_mode = <1>; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| ldo13_reg: LDO13 { |
| regulator-name = "VCC_1.8V_MHL"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| op_mode = <1>; |
| }; |
| |
| ldo15_reg: LDO15 { |
| regulator-name = "VHSIC_1.0V"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| op_mode = <1>; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| ldo17_reg: LDO17 { |
| regulator-name = "VCC_2.8V_AP"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| op_mode = <1>; |
| regulator-always-on; |
| }; |
| |
| ldo19_reg: LDO19 { |
| regulator-name = "VLED_IC_1.9V"; |
| regulator-min-microvolt = <1900000>; |
| regulator-max-microvolt = <1900000>; |
| op_mode = <1>; |
| regulator-always-on; |
| }; |
| |
| ldo20_reg: LDO20 { |
| regulator-name = "VTOUCH_3.3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| op_mode = <1>; |
| }; |
| |
| ldo21_reg: LDO21 { |
| regulator-name = "TSP_VDD_3.3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| op_mode = <1>; |
| }; |
| |
| ldo22_reg: LDO22 { |
| regulator-name = "5M_AF_2.8V"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| op_mode = <1>; |
| }; |
| |
| ldo23_reg: LDO23 { |
| regulator-name = "VTF_2.8V"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| op_mode = <3>; |
| }; |
| |
| ldo24_reg: LDO24 { |
| regulator-name = "LEDA_2.8V"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| op_mode = <1>; |
| }; |
| |
| ldo25_reg: LDO25 { |
| regulator-name = "TSP_VDD_1.8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| op_mode = <1>; |
| }; |
| |
| ldo26_reg: LDO26 { |
| regulator-name = "CAM_IO_1.8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| op_mode = <1>; |
| }; |
| |
| ldo27_reg: LDO27 { |
| regulator-name = "VTCAM_1.8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| op_mode = <1>; |
| }; |
| |
| buck1_reg: BUCK1 { |
| regulator-name = "VDD_MIF"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1100000>; |
| regulator-always-on; |
| regulator-boot-on; |
| op_mode = <3>; |
| }; |
| |
| buck2_reg: BUCK2 { |
| regulator-name = "VDD_ARM"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1500000>; |
| regulator-always-on; |
| regulator-boot-on; |
| op_mode = <3>; |
| }; |
| |
| buck3_reg: BUCK3 { |
| regulator-name = "VDD_INT"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1300000>; |
| regulator-always-on; |
| regulator-boot-on; |
| op_mode = <3>; |
| }; |
| |
| buck4_reg: BUCK4 { |
| regulator-name = "VDD_G3D"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <1150000>; |
| regulator-boot-on; |
| op_mode = <3>; |
| }; |
| |
| buck5_reg: BUCK5 { |
| regulator-name = "VMEM_1.2V_AP"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-always-on; |
| regulator-boot-on; |
| op_mode = <1>; |
| }; |
| |
| buck6_reg: BUCK6 { |
| regulator-name = "CAM_ISP_CORE_1.2V"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| op_mode = <1>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| }; |
| |
| s5m8767_osc: clocks { |
| compatible = "samsung,s5m8767-clk"; |
| #clock-cells = <1>; |
| clock-output-names = "en32khz_ap", |
| "en32khz_cp", |
| "en32khz_bt"; |
| }; |
| }; |
| }; |
| |
| &i2s0 { |
| pinctrl-0 = <&i2s0_bus>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| }; |
| |
| &mshc_0 { |
| broken-cd; |
| non-removable; |
| card-detect-delay = <200>; |
| vmmc-supply = <&ldo22_reg>; |
| clock-frequency = <400000000>; |
| samsung,dw-mshc-ciu-div = <0>; |
| samsung,dw-mshc-sdr-timing = <2 3>; |
| samsung,dw-mshc-ddr-timing = <1 2>; |
| pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>; |
| pinctrl-names = "default"; |
| bus-width = <8>; |
| cap-mmc-highspeed; |
| mmc-ddr-1_8v; |
| status = "okay"; |
| }; |
| |
| &pinctrl_0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sleep0>; |
| |
| lcd_en: lcd-en-pins { |
| samsung,pins = "gpc0-1"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| lcd_nrst: lcd-nrst-pins { |
| samsung,pins = "gpf0-4"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| s5m8767_ds: s5m8767-ds-pins { |
| samsung,pins = "gpf3-1", "gpf3-2", "gpf3-3"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| sleep0: sleep-state { |
| PIN_SLP(gpa0-0, INPUT, NONE); |
| PIN_SLP(gpa0-1, OUT0, NONE); |
| PIN_SLP(gpa0-2, INPUT, NONE); |
| PIN_SLP(gpa0-3, INPUT, UP); |
| PIN_SLP(gpa0-4, INPUT, DOWN); |
| PIN_SLP(gpa0-5, INPUT, DOWN); |
| PIN_SLP(gpa0-6, INPUT, DOWN); |
| PIN_SLP(gpa0-7, INPUT, DOWN); |
| |
| PIN_SLP(gpa1-0, INPUT, DOWN); |
| PIN_SLP(gpa1-1, INPUT, DOWN); |
| PIN_SLP(gpa1-2, INPUT, DOWN); |
| PIN_SLP(gpa1-3, INPUT, DOWN); |
| PIN_SLP(gpa1-4, INPUT, DOWN); |
| PIN_SLP(gpa1-5, INPUT, DOWN); |
| |
| PIN_SLP(gpb-0, INPUT, NONE); |
| PIN_SLP(gpb-1, INPUT, NONE); |
| PIN_SLP(gpb-2, INPUT, NONE); |
| PIN_SLP(gpb-3, INPUT, NONE); |
| PIN_SLP(gpb-4, INPUT, DOWN); |
| PIN_SLP(gpb-5, INPUT, DOWN); |
| PIN_SLP(gpb-6, INPUT, DOWN); |
| PIN_SLP(gpb-7, INPUT, DOWN); |
| |
| PIN_SLP(gpc0-0, INPUT, DOWN); |
| PIN_SLP(gpc0-1, INPUT, DOWN); |
| PIN_SLP(gpc0-2, INPUT, NONE); |
| PIN_SLP(gpc0-3, INPUT, NONE); |
| PIN_SLP(gpc0-4, INPUT, NONE); |
| |
| PIN_SLP(gpc1-0, INPUT, DOWN); |
| PIN_SLP(gpc1-1, INPUT, DOWN); |
| PIN_SLP(gpc1-2, INPUT, DOWN); |
| PIN_SLP(gpc1-3, INPUT, DOWN); |
| PIN_SLP(gpc1-4, INPUT, DOWN); |
| |
| PIN_SLP(gpd0-0, INPUT, DOWN); |
| PIN_SLP(gpd0-1, OUT0, NONE); |
| PIN_SLP(gpd0-2, INPUT, NONE); |
| PIN_SLP(gpd0-3, INPUT, NONE); |
| |
| PIN_SLP(gpd1-0, INPUT, DOWN); |
| PIN_SLP(gpd1-1, INPUT, DOWN); |
| PIN_SLP(gpd1-2, INPUT, NONE); |
| PIN_SLP(gpd1-3, INPUT, NONE); |
| |
| PIN_SLP(gpf0-0, INPUT, DOWN); |
| PIN_SLP(gpf0-1, INPUT, DOWN); |
| PIN_SLP(gpf0-2, INPUT, DOWN); |
| PIN_SLP(gpf0-3, INPUT, DOWN); |
| PIN_SLP(gpf0-4, OUT0, NONE); |
| PIN_SLP(gpf0-5, OUT0, NONE); |
| PIN_SLP(gpf0-6, INPUT, DOWN); |
| PIN_SLP(gpf0-7, INPUT, DOWN); |
| |
| PIN_SLP(gpf1-0, INPUT, DOWN); |
| PIN_SLP(gpf1-1, INPUT, DOWN); |
| PIN_SLP(gpf1-2, INPUT, DOWN); |
| PIN_SLP(gpf1-3, INPUT, DOWN); |
| PIN_SLP(gpf1-4, INPUT, DOWN); |
| PIN_SLP(gpf1-5, INPUT, DOWN); |
| PIN_SLP(gpf1-6, INPUT, DOWN); |
| PIN_SLP(gpf1-7, INPUT, DOWN); |
| |
| PIN_SLP(gpf2-0, INPUT, DOWN); |
| PIN_SLP(gpf2-1, INPUT, DOWN); |
| PIN_SLP(gpf2-2, INPUT, DOWN); |
| PIN_SLP(gpf2-3, INPUT, DOWN); |
| PIN_SLP(gpf2-4, INPUT, DOWN); |
| PIN_SLP(gpf2-5, INPUT, DOWN); |
| PIN_SLP(gpf2-6, INPUT, DOWN); |
| PIN_SLP(gpf2-7, INPUT, DOWN); |
| |
| PIN_SLP(gpf3-0, INPUT, DOWN); |
| PIN_SLP(gpf3-1, INPUT, DOWN); |
| PIN_SLP(gpf3-2, INPUT, DOWN); |
| PIN_SLP(gpf3-3, INPUT, DOWN); |
| PIN_SLP(gpf3-4, PREV, NONE); |
| PIN_SLP(gpf3-5, OUT0, DOWN); |
| |
| PIN_SLP(gpj0-0, INPUT, DOWN); |
| PIN_SLP(gpj0-1, INPUT, DOWN); |
| PIN_SLP(gpj0-2, INPUT, DOWN); |
| PIN_SLP(gpj0-3, OUT0, NONE); |
| PIN_SLP(gpj0-4, INPUT, DOWN); |
| PIN_SLP(gpj0-5, INPUT, DOWN); |
| PIN_SLP(gpj0-6, OUT0, NONE); |
| PIN_SLP(gpj0-7, OUT0, NONE); |
| |
| PIN_SLP(gpj1-0, OUT0, NONE); |
| PIN_SLP(gpj1-1, INPUT, DOWN); |
| PIN_SLP(gpj1-2, PREV, NONE); |
| PIN_SLP(gpj1-3, INPUT, DOWN); |
| PIN_SLP(gpj1-4, INPUT, DOWN); |
| }; |
| }; |
| |
| &pinctrl_1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sleep1>; |
| |
| bt_shutdown: bt-shutdown-pins { |
| samsung,pins = "gpl0-6"; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| bt_host_wakeup: bt-host-wakeup-pins { |
| samsung,pins = "gpx2-6"; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| bt_device_wakeup: bt-device-wakeup-pins { |
| samsung,pins = "gpx3-1"; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| backlight_reset: backlight-reset-pins { |
| samsung,pins = "gpm0-1"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| gpio_keys: gpio-keys-pins { |
| samsung,pins = "gpx1-2", "gpx2-2", "gpx2-4", "gpx2-7", "gpx3-3"; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| }; |
| |
| max77693_irq: max77693-irq-pins { |
| samsung,pins = "gpx1-5"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| max77693_fuel_irq: max77693-fuel-irq-pins { |
| samsung,pins = "gpx2-3"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| sdhci2_cd: sdhci2-cd-irq-pins { |
| samsung,pins = "gpx3-4"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| s5m8767_dvs: s5m8767-dvs-pins { |
| samsung,pins = "gpm3-0", "gpm3-1", "gpm3-2"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| s5m8767_irq: s5m8767-irq-pins { |
| samsung,pins = "gpx0-7"; |
| samsung,pin-function = <EXYNOS_PIN_FUNC_EINT>; |
| samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
| samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; |
| }; |
| |
| sleep1: sleep-state { |
| PIN_SLP(gpk0-0, PREV, NONE); |
| PIN_SLP(gpk0-1, PREV, NONE); |
| PIN_SLP(gpk0-2, PREV, NONE); |
| PIN_SLP(gpk0-3, PREV, NONE); |
| PIN_SLP(gpk0-4, PREV, NONE); |
| PIN_SLP(gpk0-5, PREV, NONE); |
| PIN_SLP(gpk0-6, PREV, NONE); |
| |
| PIN_SLP(gpk1-0, INPUT, DOWN); |
| PIN_SLP(gpk1-1, INPUT, DOWN); |
| PIN_SLP(gpk1-2, INPUT, DOWN); |
| PIN_SLP(gpk1-3, PREV, NONE); |
| PIN_SLP(gpk1-4, PREV, NONE); |
| PIN_SLP(gpk1-5, PREV, NONE); |
| PIN_SLP(gpk1-6, PREV, NONE); |
| |
| PIN_SLP(gpk2-0, INPUT, DOWN); |
| PIN_SLP(gpk2-1, INPUT, DOWN); |
| PIN_SLP(gpk2-2, INPUT, DOWN); |
| PIN_SLP(gpk2-3, INPUT, DOWN); |
| PIN_SLP(gpk2-4, INPUT, DOWN); |
| PIN_SLP(gpk2-5, INPUT, DOWN); |
| PIN_SLP(gpk2-6, INPUT, DOWN); |
| |
| PIN_SLP(gpk3-0, OUT0, NONE); |
| PIN_SLP(gpk3-1, INPUT, NONE); |
| PIN_SLP(gpk3-2, INPUT, DOWN); |
| PIN_SLP(gpk3-3, INPUT, NONE); |
| PIN_SLP(gpk3-4, INPUT, NONE); |
| PIN_SLP(gpk3-5, INPUT, NONE); |
| PIN_SLP(gpk3-6, INPUT, NONE); |
| |
| PIN_SLP(gpl0-0, INPUT, DOWN); |
| PIN_SLP(gpl0-1, INPUT, NONE); |
| PIN_SLP(gpl0-2, INPUT, NONE); |
| PIN_SLP(gpl0-3, INPUT, DOWN); |
| PIN_SLP(gpl0-4, INPUT, DOWN); |
| PIN_SLP(gpl0-6, PREV, NONE); |
| |
| PIN_SLP(gpl1-0, INPUT, DOWN); |
| PIN_SLP(gpl1-1, OUT0, NONE); |
| PIN_SLP(gpl2-0, INPUT, DOWN); |
| PIN_SLP(gpl2-1, PREV, NONE); |
| PIN_SLP(gpl2-2, PREV, NONE); |
| PIN_SLP(gpl2-3, INPUT, DOWN); |
| PIN_SLP(gpl2-4, INPUT, DOWN); |
| PIN_SLP(gpl2-5, INPUT, DOWN); |
| PIN_SLP(gpl2-6, INPUT, DOWN); |
| PIN_SLP(gpl2-7, INPUT, DOWN); |
| |
| PIN_SLP(gpm0-0, PREV, NONE); |
| PIN_SLP(gpm0-1, OUT0, NONE); |
| PIN_SLP(gpm0-2, INPUT, DOWN); |
| PIN_SLP(gpm0-3, INPUT, DOWN); |
| PIN_SLP(gpm0-4, INPUT, DOWN); |
| PIN_SLP(gpm0-5, INPUT, DOWN); |
| PIN_SLP(gpm0-6, INPUT, DOWN); |
| PIN_SLP(gpm0-7, INPUT, DOWN); |
| |
| PIN_SLP(gpm1-0, INPUT, DOWN); |
| PIN_SLP(gpm1-1, INPUT, DOWN); |
| PIN_SLP(gpm1-2, INPUT, NONE); |
| PIN_SLP(gpm1-3, INPUT, NONE); |
| PIN_SLP(gpm1-4, INPUT, NONE); |
| PIN_SLP(gpm1-5, INPUT, NONE); |
| PIN_SLP(gpm1-6, OUT0, NONE); |
| |
| PIN_SLP(gpm2-0, INPUT, NONE); |
| PIN_SLP(gpm2-1, INPUT, NONE); |
| PIN_SLP(gpm2-2, OUT0, NONE); |
| PIN_SLP(gpm2-3, INPUT, DOWN); |
| PIN_SLP(gpm2-4, INPUT, DOWN); |
| |
| PIN_SLP(gpm3-0, PREV, NONE); |
| PIN_SLP(gpm3-1, PREV, NONE); |
| PIN_SLP(gpm3-2, PREV, NONE); |
| PIN_SLP(gpm3-3, INPUT, DOWN); |
| PIN_SLP(gpm3-4, INPUT, DOWN); |
| PIN_SLP(gpm3-5, PREV, NONE); |
| PIN_SLP(gpm3-6, INPUT, DOWN); |
| PIN_SLP(gpm3-7, OUT0, NONE); |
| |
| PIN_SLP(gpm4-0, INPUT, DOWN); |
| PIN_SLP(gpm4-1, INPUT, DOWN); |
| PIN_SLP(gpm4-2, INPUT, DOWN); |
| PIN_SLP(gpm4-3, INPUT, DOWN); |
| PIN_SLP(gpm4-4, PREV, NONE); |
| PIN_SLP(gpm4-5, INPUT, NONE); |
| PIN_SLP(gpm4-6, INPUT, DOWN); |
| PIN_SLP(gpm4-7, INPUT, DOWN); |
| |
| PIN_SLP(gpy0-0, INPUT, DOWN); |
| PIN_SLP(gpy0-1, INPUT, DOWN); |
| PIN_SLP(gpy0-2, INPUT, NONE); |
| PIN_SLP(gpy0-3, INPUT, NONE); |
| PIN_SLP(gpy0-4, INPUT, DOWN); |
| PIN_SLP(gpy0-5, INPUT, DOWN); |
| |
| PIN_SLP(gpy1-0, INPUT, DOWN); |
| PIN_SLP(gpy1-1, INPUT, DOWN); |
| PIN_SLP(gpy1-2, INPUT, DOWN); |
| PIN_SLP(gpy1-3, INPUT, DOWN); |
| |
| PIN_SLP(gpy2-0, PREV, NONE); |
| PIN_SLP(gpy2-1, INPUT, DOWN); |
| PIN_SLP(gpy2-2, INPUT, NONE); |
| PIN_SLP(gpy2-3, INPUT, NONE); |
| PIN_SLP(gpy2-4, INPUT, NONE); |
| PIN_SLP(gpy2-5, INPUT, NONE); |
| |
| PIN_SLP(gpy3-0, INPUT, DOWN); |
| PIN_SLP(gpy3-1, INPUT, DOWN); |
| PIN_SLP(gpy3-2, INPUT, DOWN); |
| PIN_SLP(gpy3-3, INPUT, DOWN); |
| PIN_SLP(gpy3-4, INPUT, DOWN); |
| PIN_SLP(gpy3-5, INPUT, DOWN); |
| PIN_SLP(gpy3-6, INPUT, DOWN); |
| PIN_SLP(gpy3-7, INPUT, DOWN); |
| |
| PIN_SLP(gpy4-0, INPUT, DOWN); |
| PIN_SLP(gpy4-1, INPUT, DOWN); |
| PIN_SLP(gpy4-2, INPUT, DOWN); |
| PIN_SLP(gpy4-3, INPUT, DOWN); |
| PIN_SLP(gpy4-4, INPUT, DOWN); |
| PIN_SLP(gpy4-5, INPUT, DOWN); |
| PIN_SLP(gpy4-6, INPUT, DOWN); |
| PIN_SLP(gpy4-7, INPUT, DOWN); |
| |
| PIN_SLP(gpy5-0, INPUT, DOWN); |
| PIN_SLP(gpy5-1, INPUT, DOWN); |
| PIN_SLP(gpy5-2, INPUT, DOWN); |
| PIN_SLP(gpy5-3, INPUT, DOWN); |
| PIN_SLP(gpy5-4, INPUT, DOWN); |
| PIN_SLP(gpy5-5, INPUT, DOWN); |
| PIN_SLP(gpy5-6, INPUT, DOWN); |
| PIN_SLP(gpy5-7, INPUT, DOWN); |
| |
| PIN_SLP(gpy6-0, INPUT, DOWN); |
| PIN_SLP(gpy6-1, INPUT, DOWN); |
| PIN_SLP(gpy6-2, INPUT, DOWN); |
| PIN_SLP(gpy6-3, INPUT, DOWN); |
| PIN_SLP(gpy6-4, INPUT, DOWN); |
| PIN_SLP(gpy6-5, INPUT, DOWN); |
| PIN_SLP(gpy6-6, INPUT, DOWN); |
| PIN_SLP(gpy6-7, INPUT, DOWN); |
| }; |
| }; |
| |
| &pinctrl_2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sleep2>; |
| |
| sleep2: sleep-state { |
| PIN_SLP(gpz-0, INPUT, DOWN); |
| PIN_SLP(gpz-1, INPUT, DOWN); |
| PIN_SLP(gpz-2, INPUT, DOWN); |
| PIN_SLP(gpz-3, INPUT, DOWN); |
| PIN_SLP(gpz-4, INPUT, DOWN); |
| PIN_SLP(gpz-5, INPUT, DOWN); |
| PIN_SLP(gpz-6, INPUT, DOWN); |
| }; |
| }; |
| |
| &pinctrl_3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sleep3>; |
| |
| sleep3: sleep-state { |
| PIN_SLP(gpv0-0, INPUT, DOWN); |
| PIN_SLP(gpv0-1, INPUT, DOWN); |
| PIN_SLP(gpv0-2, INPUT, DOWN); |
| PIN_SLP(gpv0-3, INPUT, DOWN); |
| PIN_SLP(gpv0-4, INPUT, DOWN); |
| PIN_SLP(gpv0-5, INPUT, DOWN); |
| PIN_SLP(gpv0-6, INPUT, DOWN); |
| PIN_SLP(gpv0-7, INPUT, DOWN); |
| |
| PIN_SLP(gpv1-0, INPUT, DOWN); |
| PIN_SLP(gpv1-1, INPUT, DOWN); |
| PIN_SLP(gpv1-2, INPUT, DOWN); |
| PIN_SLP(gpv1-3, INPUT, DOWN); |
| PIN_SLP(gpv1-4, INPUT, DOWN); |
| PIN_SLP(gpv1-5, INPUT, DOWN); |
| PIN_SLP(gpv1-6, INPUT, DOWN); |
| PIN_SLP(gpv1-7, INPUT, DOWN); |
| |
| PIN_SLP(gpv2-0, INPUT, DOWN); |
| PIN_SLP(gpv2-1, INPUT, DOWN); |
| PIN_SLP(gpv2-2, INPUT, DOWN); |
| PIN_SLP(gpv2-3, INPUT, DOWN); |
| PIN_SLP(gpv2-4, INPUT, DOWN); |
| PIN_SLP(gpv2-5, INPUT, DOWN); |
| PIN_SLP(gpv2-6, INPUT, DOWN); |
| PIN_SLP(gpv2-7, INPUT, DOWN); |
| |
| PIN_SLP(gpv3-0, INPUT, DOWN); |
| PIN_SLP(gpv3-1, INPUT, DOWN); |
| PIN_SLP(gpv3-2, INPUT, DOWN); |
| PIN_SLP(gpv3-3, INPUT, DOWN); |
| PIN_SLP(gpv3-4, INPUT, DOWN); |
| PIN_SLP(gpv3-5, INPUT, DOWN); |
| PIN_SLP(gpv3-6, INPUT, DOWN); |
| PIN_SLP(gpv3-7, INPUT, DOWN); |
| |
| PIN_SLP(gpv4-0, INPUT, DOWN); |
| PIN_SLP(gpv4-1, INPUT, DOWN); |
| }; |
| }; |
| |
| &pmu_system_controller { |
| assigned-clocks = <&pmu_system_controller 0>; |
| assigned-clock-parents = <&clock CLK_XUSBXTI>; |
| }; |
| |
| &pwm { |
| pinctrl-0 = <&pwm1_out>; |
| pinctrl-names = "default"; |
| samsung,pwm-outputs = <1>; |
| status = "okay"; |
| }; |
| |
| /* |
| * The internal RTC does not work; instead, the RTC provided by the |
| * S5M8766 PMIC is used. Disable the RTC to make sure the working |
| * one gets used. |
| * |
| * We add this node to avoid DTB check warnings, as the Exynos4 RTC |
| * requires two clocks, and only one is set up by default. |
| */ |
| &rtc { |
| clocks = <&clock CLK_RTC>, <&s5m8767_osc S2MPS11_CLK_AP>; |
| clock-names = "rtc", "rtc_src"; |
| status = "disabled"; |
| }; |
| |
| &sdhci_2 { |
| bus-width = <4>; |
| cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>; |
| pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>; |
| pinctrl-names = "default"; |
| vmmc-supply = <&ldo23_reg>; |
| status = "okay"; |
| }; |
| |
| &sdhci_3 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| non-removable; |
| bus-width = <4>; |
| |
| mmc-pwrseq = <&wlan_pwrseq>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>; |
| status = "okay"; |
| |
| brcmf: wifi@1 { |
| compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac"; |
| reg = <1>; |
| |
| interrupt-parent = <&gpx2>; |
| interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "host-wake"; |
| }; |
| }; |
| |
| &serial_0 { |
| pinctrl-0 = <&uart0_data &uart0_fctl>; |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| bluetooth { |
| compatible = "brcm,bcm4330-bt"; /* BCM4334B0 */ |
| pinctrl-0 = <&bt_shutdown &bt_device_wakeup &bt_host_wakeup>; |
| pinctrl-names = "default"; |
| max-speed = <3000000>; |
| shutdown-gpios = <&gpl0 6 GPIO_ACTIVE_HIGH>; |
| device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>; |
| host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>; |
| clocks = <&s5m8767_osc S2MPS11_CLK_BT>; |
| }; |
| }; |
| |
| &serial_1 { |
| status = "okay"; |
| }; |
| |
| &serial_2 { |
| status = "okay"; |
| }; |
| |
| &serial_3 { |
| status = "okay"; |
| }; |
| |
| &tmu { |
| vtmu-supply = <&ldo10_reg>; |
| status = "okay"; |
| }; |