Squashed 'dts/upstream/' content from commit aaba2d45dc2a
git-subtree-dir: dts/upstream
git-subtree-split: aaba2d45dc2a1b3bbb710f2a3808ee1c9f340abe
diff --git a/src/arm/gemini/gemini-dlink-dir-685.dts b/src/arm/gemini/gemini-dlink-dir-685.dts
new file mode 100644
index 0000000..3961496
--- /dev/null
+++ b/src/arm/gemini/gemini-dlink-dir-685.dts
@@ -0,0 +1,492 @@
+/*
+ * Device Tree file for D-Link DIR-685 Xtreme N Storage Router
+ */
+
+/dts-v1/;
+
+#include "gemini.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "D-Link DIR-685 Xtreme N Storage Router";
+ compatible = "dlink,dir-685", "cortina,gemini";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory@0 {
+ /* 128 MB SDRAM in 2 x Hynix HY5DU121622DTP-D43 */
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,19200n8 root=/dev/sda1 rw rootwait consoleblank=300";
+ stdout-path = "uart0:19200n8";
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ button-esc {
+ debounce-interval = <100>;
+ wakeup-source;
+ linux,code = <KEY_ESC>;
+ label = "reset";
+ /* Collides with LPC_LAD[0], UART DCD, SSP 97RST */
+ gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
+ };
+ button-eject {
+ debounce-interval = <100>;
+ wakeup-source;
+ linux,code = <KEY_EJECTCD>;
+ label = "unmount";
+ /* Collides with LPC LFRAME, UART RTS, SSP TXD */
+ gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ vdisp: regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "display-power";
+ regulator-min-microvolt = <3600000>;
+ regulator-max-microvolt = <3600000>;
+ /* Collides with LCD E */
+ gpio = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ spi {
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Collides with IDE pins, that's cool (we do not use them) */
+ sck-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ miso-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ mosi-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
+ num-chipselects = <1>;
+
+ panel: display@0 {
+ compatible = "dlink,dir-685-panel", "ilitek,ili9322";
+ reg = <0>;
+ /* 50 ns min period = 20 MHz */
+ spi-max-frequency = <20000000>;
+ vcc-supply = <&vdisp>;
+ iovcc-supply = <&vdisp>;
+ vci-supply = <&vdisp>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led-wps {
+ label = "dir685:blue:WPS";
+ /* Collides with ICE */
+ gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+ /*
+ * These two LEDs are on the side of the device.
+ * For electrical reasons, both LEDs cannot be active
+ * at the same time so only blue or orange can be on at
+ * one time. Enabling both makes the LED go dark.
+ * The LEDs both sit inside the unmount button and the
+ * label on the case says "unmount".
+ */
+ led-blue-hd {
+ label = "dir685:blue:HD";
+ /* Collides with LPC_SERIRQ, UART DTR, SSP FSC pins */
+ gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "disk-read";
+ };
+ led-orange-hd {
+ label = "dir685:orange:HD";
+ /* Collides with LPC_LAD[2], UART DSR, SSP ECLK pins */
+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "disk-write";
+ };
+ };
+
+ /*
+ * This is a Sunon Maglev GM0502PFV2-8 cooling fan @10000 RPM.
+ * sensor. It is turned on when the temperature exceeds 46 degrees
+ * and turned off when the temperatures goes below 41 degrees
+ * (celsius).
+ */
+ fan0: gpio-fan {
+ compatible = "gpio-fan";
+ /* Collides with IDE */
+ gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+ gpio-fan,speed-map = <0 0>, <10000 1>;
+ #cooling-cells = <2>;
+ };
+
+ thermal-zones {
+ chassis-thermal {
+ /* Poll every 20 seconds */
+ polling-delay = <20000>;
+ /* Poll every 2nd second when cooling */
+ polling-delay-passive = <2000>;
+ /* Use the thermal sensor in the hard drive */
+ thermal-sensors = <&drive0>;
+
+ /* Tripping points from the fan.script in the rootfs */
+ trips {
+ alert: chassis-alert {
+ /* At 43 degrees turn on the fan */
+ temperature = <43000>;
+ hysteresis = <3000>;
+ type = "active";
+ };
+ crit: chassis-crit {
+ /* Just shut down at 60 degrees */
+ temperature = <60000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&alert>;
+ cooling-device = <&fan0 1 1>;
+ };
+ };
+ };
+ };
+
+ /*
+ * The touchpad input is connected to a GPIO bit-banged
+ * I2C bus.
+ */
+ i2c {
+ compatible = "i2c-gpio";
+ /* Collides with ICE */
+ sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ touchkeys@26 {
+ compatible = "dlink,dir685-touchkeys";
+ reg = <0x26>;
+ interrupt-parent = <&gpio0>;
+ /* Collides with NAND flash */
+ interrupts = <17 IRQ_TYPE_EDGE_FALLING>;
+ };
+ };
+
+ /* This is a RealTek RTL8366RB switch and PHY using SMI over GPIO */
+ switch {
+ compatible = "realtek,rtl8366rb";
+ /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */
+ mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
+ mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+ realtek,disable-leds;
+
+ switch_intc: interrupt-controller {
+ /* GPIO 15 provides the interrupt */
+ interrupt-parent = <&gpio0>;
+ interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan0";
+ phy-handle = <&phy0>;
+ };
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ phy-handle = <&phy1>;
+ };
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ phy-handle = <&phy2>;
+ };
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ phy-handle = <&phy3>;
+ };
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ phy-handle = <&phy4>;
+ };
+ rtl8366rb_cpu_port: port@5 {
+ reg = <5>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+
+ };
+
+ mdio {
+ compatible = "realtek,smi-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: phy@0 {
+ reg = <0>;
+ interrupt-parent = <&switch_intc>;
+ interrupts = <0>;
+ };
+ phy1: phy@1 {
+ reg = <1>;
+ interrupt-parent = <&switch_intc>;
+ interrupts = <1>;
+ };
+ phy2: phy@2 {
+ reg = <2>;
+ interrupt-parent = <&switch_intc>;
+ interrupts = <2>;
+ };
+ phy3: phy@3 {
+ reg = <3>;
+ interrupt-parent = <&switch_intc>;
+ interrupts = <3>;
+ };
+ phy4: phy@4 {
+ reg = <4>;
+ interrupt-parent = <&switch_intc>;
+ interrupts = <12>;
+ };
+ };
+ };
+
+ soc {
+ flash@30000000 {
+ /*
+ * Flash access collides with the Chip Enable signal for
+ * the display panel, that reuse the parallel flash Chip
+ * Select 1 (CS1). We switch the pin control state so we
+ * enable these pins for flash access only when we need
+ * then, and when disabled they can be used for GPIO which
+ * is what the display panel needs.
+ */
+ status = "okay";
+ pinctrl-names = "enabled", "disabled";
+ pinctrl-0 = <&pflash_default_pins>;
+ pinctrl-1 = <&pflash_disabled_pins>;
+
+ /* 32MB of flash */
+ reg = <0x30000000 0x02000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /*
+ * This "RedBoot" is the Storlink derivative.
+ */
+ partition@0 {
+ label = "RedBoot";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+ /*
+ * This firmware image contains the kernel catenated
+ * with the squashfs root filesystem. For some reason
+ * this is called "upgrade" on the vendor system.
+ */
+ partition@40000 {
+ label = "upgrade";
+ reg = <0x00040000 0x01f40000>;
+ read-only;
+ };
+ /* RGDB, Residental Gateway Database? */
+ partition@1f80000 {
+ label = "rgdb";
+ reg = <0x01f80000 0x00040000>;
+ read-only;
+ };
+ /*
+ * This partition contains MAC addresses for WAN,
+ * WLAN and LAN, and the country code (for wireless
+ * I guess).
+ */
+ partition@1fc0000 {
+ label = "nvram";
+ reg = <0x01fc0000 0x00020000>;
+ read-only;
+ };
+ partition@1fe0000 {
+ label = "LangPack";
+ reg = <0x01fe0000 0x00020000>;
+ read-only;
+ };
+ };
+ };
+
+ syscon: syscon@40000000 {
+ pinctrl {
+ /*
+ * gpio0bgrp cover line 5, 6 used by TK I2C
+ * gpio0bgrp cover line 7 used by WPS LED
+ * gpio0cgrp cover line 8, 13 used by keys
+ * and 11, 12 used by the HD LEDs
+ * and line 14, 15 used by RTL8366
+ * RESET and phy ready
+ * gpio0egrp cover line 16 used by VDISP
+ * gpio0fgrp cover line 17 used by TK IRQ
+ * gpio0ggrp cover line 20 used by panel CS
+ * gpio0hgrp cover line 21,22 used by RTL8366RB MDIO
+ */
+ gpio0_default_pins: pinctrl-gpio0 {
+ mux {
+ function = "gpio0";
+ groups = "gpio0bgrp",
+ "gpio0cgrp",
+ "gpio0egrp",
+ "gpio0fgrp",
+ "gpio0hgrp";
+ };
+ };
+ /*
+ * gpio1bgrp cover line 5,8,7 used by panel SPI
+ * also line 6 used by the fan
+ *
+ */
+ gpio1_default_pins: pinctrl-gpio1 {
+ mux {
+ function = "gpio1";
+ groups = "gpio1bgrp";
+ };
+ };
+ /*
+ * These GPIO groups will be mapped in over some
+ * of the flash pins when the flash is not in
+ * active use.
+ */
+ pflash_disabled_pins: pinctrl-pflash-disabled {
+ mux {
+ function = "gpio0";
+ groups = "gpio0ggrp", "gpio0igrp", "gpio0jgrp",
+ "gpio0kgrp";
+ };
+ };
+ pinctrl-gmii {
+ mux {
+ function = "gmii";
+ groups = "gmii_gmac0_grp";
+ };
+ conf0 {
+ pins = "V8 GMAC0 RXDV", "T10 GMAC1 RXDV",
+ "Y7 GMAC0 RXC", "Y11 GMAC1 RXC",
+ "T8 GMAC0 TXEN", "W11 GMAC1 TXEN",
+ "U8 GMAC0 TXC", "V11 GMAC1 TXC",
+ "W8 GMAC0 RXD0", "V9 GMAC0 RXD1",
+ "Y8 GMAC0 RXD2", "U9 GMAC0 RXD3",
+ "T7 GMAC0 TXD0", "U6 GMAC0 TXD1",
+ "V7 GMAC0 TXD2", "U7 GMAC0 TXD3",
+ "Y12 GMAC1 RXD0", "V12 GMAC1 RXD1",
+ "T11 GMAC1 RXD2", "W12 GMAC1 RXD3",
+ "U10 GMAC1 TXD0", "Y10 GMAC1 TXD1",
+ "W10 GMAC1 TXD2", "T9 GMAC1 TXD3";
+ skew-delay = <7>;
+ };
+ /* Set up drive strength on GMAC0 to 16 mA */
+ conf1 {
+ groups = "gmii_gmac0_grp";
+ drive-strength = <16>;
+ };
+ };
+ };
+ };
+
+ sata: sata@46000000 {
+ cortina,gemini-ata-muxmode = <0>;
+ cortina,gemini-enable-sata-bridge;
+ status = "okay";
+ };
+
+ gpio0: gpio@4d000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio0_default_pins>;
+ };
+
+ gpio1: gpio@4e000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio1_default_pins>;
+ };
+
+ pci@50000000 {
+ status = "okay";
+ };
+
+ ethernet@60000000 {
+ status = "okay";
+
+ ethernet-port@0 {
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+ ethernet-port@1 {
+ /* Not used in this platform */
+ };
+ };
+
+ ide@63000000 {
+ status = "okay";
+
+ /*
+ * This drive may have a temperature sensor with a
+ * thermal zone we can use for thermal control of the
+ * chassis temperature using the fan.
+ */
+ drive0: ide-port@0 {
+ reg = <0>;
+ #thermal-sensor-cells = <0>;
+ };
+ };
+
+ display-controller@6a000000 {
+ status = "okay";
+
+ port {
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+
+ usb@68000000 {
+ status = "okay";
+ };
+
+ usb@69000000 {
+ status = "okay";
+ };
+ };
+};