Squashed 'dts/upstream/' content from commit aaba2d45dc2a
git-subtree-dir: dts/upstream
git-subtree-split: aaba2d45dc2a1b3bbb710f2a3808ee1c9f340abe
diff --git a/src/arm/gemini/gemini-dlink-dir-685.dts b/src/arm/gemini/gemini-dlink-dir-685.dts
new file mode 100644
index 0000000..3961496
--- /dev/null
+++ b/src/arm/gemini/gemini-dlink-dir-685.dts
@@ -0,0 +1,492 @@
+/*
+ * Device Tree file for D-Link DIR-685 Xtreme N Storage Router
+ */
+
+/dts-v1/;
+
+#include "gemini.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "D-Link DIR-685 Xtreme N Storage Router";
+ compatible = "dlink,dir-685", "cortina,gemini";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory@0 {
+ /* 128 MB SDRAM in 2 x Hynix HY5DU121622DTP-D43 */
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,19200n8 root=/dev/sda1 rw rootwait consoleblank=300";
+ stdout-path = "uart0:19200n8";
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ button-esc {
+ debounce-interval = <100>;
+ wakeup-source;
+ linux,code = <KEY_ESC>;
+ label = "reset";
+ /* Collides with LPC_LAD[0], UART DCD, SSP 97RST */
+ gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
+ };
+ button-eject {
+ debounce-interval = <100>;
+ wakeup-source;
+ linux,code = <KEY_EJECTCD>;
+ label = "unmount";
+ /* Collides with LPC LFRAME, UART RTS, SSP TXD */
+ gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ vdisp: regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "display-power";
+ regulator-min-microvolt = <3600000>;
+ regulator-max-microvolt = <3600000>;
+ /* Collides with LCD E */
+ gpio = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ spi {
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Collides with IDE pins, that's cool (we do not use them) */
+ sck-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ miso-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ mosi-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
+ num-chipselects = <1>;
+
+ panel: display@0 {
+ compatible = "dlink,dir-685-panel", "ilitek,ili9322";
+ reg = <0>;
+ /* 50 ns min period = 20 MHz */
+ spi-max-frequency = <20000000>;
+ vcc-supply = <&vdisp>;
+ iovcc-supply = <&vdisp>;
+ vci-supply = <&vdisp>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led-wps {
+ label = "dir685:blue:WPS";
+ /* Collides with ICE */
+ gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+ /*
+ * These two LEDs are on the side of the device.
+ * For electrical reasons, both LEDs cannot be active
+ * at the same time so only blue or orange can be on at
+ * one time. Enabling both makes the LED go dark.
+ * The LEDs both sit inside the unmount button and the
+ * label on the case says "unmount".
+ */
+ led-blue-hd {
+ label = "dir685:blue:HD";
+ /* Collides with LPC_SERIRQ, UART DTR, SSP FSC pins */
+ gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "disk-read";
+ };
+ led-orange-hd {
+ label = "dir685:orange:HD";
+ /* Collides with LPC_LAD[2], UART DSR, SSP ECLK pins */
+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "disk-write";
+ };
+ };
+
+ /*
+ * This is a Sunon Maglev GM0502PFV2-8 cooling fan @10000 RPM.
+ * sensor. It is turned on when the temperature exceeds 46 degrees
+ * and turned off when the temperatures goes below 41 degrees
+ * (celsius).
+ */
+ fan0: gpio-fan {
+ compatible = "gpio-fan";
+ /* Collides with IDE */
+ gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+ gpio-fan,speed-map = <0 0>, <10000 1>;
+ #cooling-cells = <2>;
+ };
+
+ thermal-zones {
+ chassis-thermal {
+ /* Poll every 20 seconds */
+ polling-delay = <20000>;
+ /* Poll every 2nd second when cooling */
+ polling-delay-passive = <2000>;
+ /* Use the thermal sensor in the hard drive */
+ thermal-sensors = <&drive0>;
+
+ /* Tripping points from the fan.script in the rootfs */
+ trips {
+ alert: chassis-alert {
+ /* At 43 degrees turn on the fan */
+ temperature = <43000>;
+ hysteresis = <3000>;
+ type = "active";
+ };
+ crit: chassis-crit {
+ /* Just shut down at 60 degrees */
+ temperature = <60000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&alert>;
+ cooling-device = <&fan0 1 1>;
+ };
+ };
+ };
+ };
+
+ /*
+ * The touchpad input is connected to a GPIO bit-banged
+ * I2C bus.
+ */
+ i2c {
+ compatible = "i2c-gpio";
+ /* Collides with ICE */
+ sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ touchkeys@26 {
+ compatible = "dlink,dir685-touchkeys";
+ reg = <0x26>;
+ interrupt-parent = <&gpio0>;
+ /* Collides with NAND flash */
+ interrupts = <17 IRQ_TYPE_EDGE_FALLING>;
+ };
+ };
+
+ /* This is a RealTek RTL8366RB switch and PHY using SMI over GPIO */
+ switch {
+ compatible = "realtek,rtl8366rb";
+ /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */
+ mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
+ mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+ realtek,disable-leds;
+
+ switch_intc: interrupt-controller {
+ /* GPIO 15 provides the interrupt */
+ interrupt-parent = <&gpio0>;
+ interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan0";
+ phy-handle = <&phy0>;
+ };
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ phy-handle = <&phy1>;
+ };
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ phy-handle = <&phy2>;
+ };
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ phy-handle = <&phy3>;
+ };
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ phy-handle = <&phy4>;
+ };
+ rtl8366rb_cpu_port: port@5 {
+ reg = <5>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+
+ };
+
+ mdio {
+ compatible = "realtek,smi-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: phy@0 {
+ reg = <0>;
+ interrupt-parent = <&switch_intc>;
+ interrupts = <0>;
+ };
+ phy1: phy@1 {
+ reg = <1>;
+ interrupt-parent = <&switch_intc>;
+ interrupts = <1>;
+ };
+ phy2: phy@2 {
+ reg = <2>;
+ interrupt-parent = <&switch_intc>;
+ interrupts = <2>;
+ };
+ phy3: phy@3 {
+ reg = <3>;
+ interrupt-parent = <&switch_intc>;
+ interrupts = <3>;
+ };
+ phy4: phy@4 {
+ reg = <4>;
+ interrupt-parent = <&switch_intc>;
+ interrupts = <12>;
+ };
+ };
+ };
+
+ soc {
+ flash@30000000 {
+ /*
+ * Flash access collides with the Chip Enable signal for
+ * the display panel, that reuse the parallel flash Chip
+ * Select 1 (CS1). We switch the pin control state so we
+ * enable these pins for flash access only when we need
+ * then, and when disabled they can be used for GPIO which
+ * is what the display panel needs.
+ */
+ status = "okay";
+ pinctrl-names = "enabled", "disabled";
+ pinctrl-0 = <&pflash_default_pins>;
+ pinctrl-1 = <&pflash_disabled_pins>;
+
+ /* 32MB of flash */
+ reg = <0x30000000 0x02000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /*
+ * This "RedBoot" is the Storlink derivative.
+ */
+ partition@0 {
+ label = "RedBoot";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+ /*
+ * This firmware image contains the kernel catenated
+ * with the squashfs root filesystem. For some reason
+ * this is called "upgrade" on the vendor system.
+ */
+ partition@40000 {
+ label = "upgrade";
+ reg = <0x00040000 0x01f40000>;
+ read-only;
+ };
+ /* RGDB, Residental Gateway Database? */
+ partition@1f80000 {
+ label = "rgdb";
+ reg = <0x01f80000 0x00040000>;
+ read-only;
+ };
+ /*
+ * This partition contains MAC addresses for WAN,
+ * WLAN and LAN, and the country code (for wireless
+ * I guess).
+ */
+ partition@1fc0000 {
+ label = "nvram";
+ reg = <0x01fc0000 0x00020000>;
+ read-only;
+ };
+ partition@1fe0000 {
+ label = "LangPack";
+ reg = <0x01fe0000 0x00020000>;
+ read-only;
+ };
+ };
+ };
+
+ syscon: syscon@40000000 {
+ pinctrl {
+ /*
+ * gpio0bgrp cover line 5, 6 used by TK I2C
+ * gpio0bgrp cover line 7 used by WPS LED
+ * gpio0cgrp cover line 8, 13 used by keys
+ * and 11, 12 used by the HD LEDs
+ * and line 14, 15 used by RTL8366
+ * RESET and phy ready
+ * gpio0egrp cover line 16 used by VDISP
+ * gpio0fgrp cover line 17 used by TK IRQ
+ * gpio0ggrp cover line 20 used by panel CS
+ * gpio0hgrp cover line 21,22 used by RTL8366RB MDIO
+ */
+ gpio0_default_pins: pinctrl-gpio0 {
+ mux {
+ function = "gpio0";
+ groups = "gpio0bgrp",
+ "gpio0cgrp",
+ "gpio0egrp",
+ "gpio0fgrp",
+ "gpio0hgrp";
+ };
+ };
+ /*
+ * gpio1bgrp cover line 5,8,7 used by panel SPI
+ * also line 6 used by the fan
+ *
+ */
+ gpio1_default_pins: pinctrl-gpio1 {
+ mux {
+ function = "gpio1";
+ groups = "gpio1bgrp";
+ };
+ };
+ /*
+ * These GPIO groups will be mapped in over some
+ * of the flash pins when the flash is not in
+ * active use.
+ */
+ pflash_disabled_pins: pinctrl-pflash-disabled {
+ mux {
+ function = "gpio0";
+ groups = "gpio0ggrp", "gpio0igrp", "gpio0jgrp",
+ "gpio0kgrp";
+ };
+ };
+ pinctrl-gmii {
+ mux {
+ function = "gmii";
+ groups = "gmii_gmac0_grp";
+ };
+ conf0 {
+ pins = "V8 GMAC0 RXDV", "T10 GMAC1 RXDV",
+ "Y7 GMAC0 RXC", "Y11 GMAC1 RXC",
+ "T8 GMAC0 TXEN", "W11 GMAC1 TXEN",
+ "U8 GMAC0 TXC", "V11 GMAC1 TXC",
+ "W8 GMAC0 RXD0", "V9 GMAC0 RXD1",
+ "Y8 GMAC0 RXD2", "U9 GMAC0 RXD3",
+ "T7 GMAC0 TXD0", "U6 GMAC0 TXD1",
+ "V7 GMAC0 TXD2", "U7 GMAC0 TXD3",
+ "Y12 GMAC1 RXD0", "V12 GMAC1 RXD1",
+ "T11 GMAC1 RXD2", "W12 GMAC1 RXD3",
+ "U10 GMAC1 TXD0", "Y10 GMAC1 TXD1",
+ "W10 GMAC1 TXD2", "T9 GMAC1 TXD3";
+ skew-delay = <7>;
+ };
+ /* Set up drive strength on GMAC0 to 16 mA */
+ conf1 {
+ groups = "gmii_gmac0_grp";
+ drive-strength = <16>;
+ };
+ };
+ };
+ };
+
+ sata: sata@46000000 {
+ cortina,gemini-ata-muxmode = <0>;
+ cortina,gemini-enable-sata-bridge;
+ status = "okay";
+ };
+
+ gpio0: gpio@4d000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio0_default_pins>;
+ };
+
+ gpio1: gpio@4e000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio1_default_pins>;
+ };
+
+ pci@50000000 {
+ status = "okay";
+ };
+
+ ethernet@60000000 {
+ status = "okay";
+
+ ethernet-port@0 {
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+ ethernet-port@1 {
+ /* Not used in this platform */
+ };
+ };
+
+ ide@63000000 {
+ status = "okay";
+
+ /*
+ * This drive may have a temperature sensor with a
+ * thermal zone we can use for thermal control of the
+ * chassis temperature using the fan.
+ */
+ drive0: ide-port@0 {
+ reg = <0>;
+ #thermal-sensor-cells = <0>;
+ };
+ };
+
+ display-controller@6a000000 {
+ status = "okay";
+
+ port {
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+
+ usb@68000000 {
+ status = "okay";
+ };
+
+ usb@69000000 {
+ status = "okay";
+ };
+ };
+};
diff --git a/src/arm/gemini/gemini-dlink-dns-313.dts b/src/arm/gemini/gemini-dlink-dns-313.dts
new file mode 100644
index 0000000..138c47e
--- /dev/null
+++ b/src/arm/gemini/gemini-dlink-dns-313.dts
@@ -0,0 +1,323 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for D-Link DNS-313 1-Bay Network Storage Enclosure
+ */
+
+/dts-v1/;
+
+#include "gemini.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ model = "D-Link DNS-313 1-Bay Network Storage Enclosure";
+ compatible = "dlink,dns-313", "cortina,gemini";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory@0 {
+ /* 64 MB SDRAM in a Nanya NT5DS32M16BS-6K package */
+ device_type = "memory";
+ reg = <0x00000000 0x4000000>;
+ };
+
+ aliases {
+ mdio-gpio0 = &mdio0;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,19200n8 root=/dev/sda4 rw rootwait";
+ stdout-path = "uart0:19200n8";
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ button-esc {
+ debounce-interval = <100>;
+ wakeup-source;
+ linux,code = <KEY_ESC>;
+ label = "reset";
+ gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led-power {
+ label = "dns313:blue:power";
+ gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+ led-disk-blue {
+ label = "dns313:blue:disk";
+ gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led-disk-green {
+ label = "dns313:green:disk";
+ gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "disk-read";
+ };
+ led-disk-red {
+ label = "dns313:red:disk";
+ gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "disk-write";
+ };
+ };
+
+ /*
+ * This is a ADDA AD0405GB-G73 fan @3000 and 6000 RPM.
+ */
+ fan0: gpio-fan {
+ compatible = "gpio-fan";
+ gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>,
+ <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ gpio-fan,speed-map = <0 0>, <3000 1>, <6000 2>;
+ #cooling-cells = <2>;
+ };
+
+ /*
+ * This is the type B USB connector on the device,
+ * a GPIO-controlled USB VBUS detect
+ */
+ usb1_phy: phy {
+ compatible = "gpio-usb-b-connector", "usb-b-connector";
+ #phy-cells = <0>;
+ vbus-gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
+ };
+
+ /* Global Mixed-Mode Technology G751 mounted on GPIO I2C */
+ i2c {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpio0 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio0 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ g751: temperature-sensor@48 {
+ compatible = "gmt,g751";
+ reg = <0x48>;
+ #thermal-sensor-cells = <0>;
+ };
+ };
+
+ thermal-zones {
+ chassis-thermal {
+ /* Poll every 20 seconds */
+ polling-delay = <20000>;
+ /* Poll every 2nd second when cooling */
+ polling-delay-passive = <2000>;
+
+ thermal-sensors = <&g751>;
+
+ /* Tripping points from the fan.script in the rootfs */
+ trips {
+ chassis_alert0: chassis-alert0 {
+ /* At 43 degrees turn on low speed */
+ temperature = <43000>;
+ hysteresis = <3000>;
+ type = "active";
+ };
+ chassis_alert1: chassis-alert1 {
+ /* At 47 degrees turn on high speed */
+ temperature = <47000>;
+ hysteresis = <3000>;
+ type = "active";
+ };
+ chassis_crit: chassis-crit {
+ /* Just shut down at 60 degrees */
+ temperature = <60000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&chassis_alert0>;
+ cooling-device = <&fan0 1 1>;
+ };
+ map1 {
+ trip = <&chassis_alert1>;
+ cooling-device = <&fan0 2 2>;
+ };
+ };
+ };
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ /* Uses MDC and MDIO */
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
+ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* This is a Realtek RTL8211B Gigabit ethernet transceiver */
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ soc {
+ flash@30000000 {
+ /*
+ * This is a Eon EN29LV400AB 512 KiB flash with
+ * three partitions.
+ */
+ compatible = "cortina,gemini-flash", "jedec-flash";
+ status = "okay";
+ reg = <0x30000000 0x00080000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /*
+ * This "RedBoot" is the Storlink derivative.
+ */
+ partition@0 {
+ label = "RedBoot";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+ partition@40000 {
+ label = "MTD1";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+ partition@60000 {
+ label = "MTD2";
+ reg = <0x00060000 0x00020000>;
+ read-only;
+ };
+ };
+
+ syscon: syscon@40000000 {
+ pinctrl {
+ /*
+ */
+ gpio0_default_pins: pinctrl-gpio0 {
+ mux {
+ function = "gpio0";
+ groups =
+ /* Used by LEDs conflicts ICE */
+ "gpio0bgrp",
+ /* Used by ? conflicts ICE */
+ "gpio0cgrp",
+ /*
+ * Used by fan & G751, conflicts LPC,
+ * UART modem lines, SSP
+ */
+ "gpio0egrp",
+ /* Used by G751 */
+ "gpio0fgrp",
+ /* Used by MDIO */
+ "gpio0igrp";
+ };
+ };
+ gpio1_default_pins: pinctrl-gpio1 {
+ mux {
+ function = "gpio1";
+ /* Used by "reset" button */
+ groups = "gpio1dgrp";
+ };
+ };
+ pinctrl-gmii {
+ mux {
+ function = "gmii";
+ groups = "gmii_gmac0_grp";
+ };
+ /*
+ * In the vendor Linux tree, these values are set for the C3
+ * version of the SL3512 ASIC with the comment "benson suggest"
+ */
+ conf0 {
+ pins = "R8 GMAC0 RXDV", "U11 GMAC1 RXDV";
+ skew-delay = <0>;
+ };
+ conf1 {
+ pins = "T8 GMAC0 RXC";
+ skew-delay = <10>;
+ };
+ conf2 {
+ pins = "T11 GMAC1 RXC";
+ skew-delay = <15>;
+ };
+ conf3 {
+ pins = "P8 GMAC0 TXEN", "V11 GMAC1 TXEN";
+ skew-delay = <7>;
+ };
+ conf4 {
+ pins = "V7 GMAC0 TXC", "P10 GMAC1 TXC";
+ skew-delay = <10>;
+ };
+ conf5 {
+ /* The data lines all have default skew */
+ pins = "U8 GMAC0 RXD0", "V8 GMAC0 RXD1",
+ "P9 GMAC0 RXD2", "R9 GMAC0 RXD3",
+ "R11 GMAC1 RXD0", "P11 GMAC1 RXD1",
+ "V12 GMAC1 RXD2", "U12 GMAC1 RXD3",
+ "R10 GMAC1 TXD0", "T10 GMAC1 TXD1",
+ "U10 GMAC1 TXD2", "V10 GMAC1 TXD3";
+ skew-delay = <7>;
+ };
+ conf6 {
+ pins = "U7 GMAC0 TXD0", "T7 GMAC0 TXD1",
+ "R7 GMAC0 TXD2", "P7 GMAC0 TXD3";
+ skew-delay = <5>;
+ };
+ /* Set up drive strength on GMAC0 to 16 mA */
+ conf7 {
+ groups = "gmii_gmac0_grp";
+ drive-strength = <16>;
+ };
+ };
+ };
+ };
+
+ sata: sata@46000000 {
+ /* The ROM uses this muxmode */
+ cortina,gemini-ata-muxmode = <0>;
+ cortina,gemini-enable-sata-bridge;
+ status = "okay";
+ };
+
+ gpio0: gpio@4d000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio0_default_pins>;
+ };
+
+ gpio1: gpio@4e000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio1_default_pins>;
+ };
+
+ ethernet@60000000 {
+ status = "okay";
+
+ ethernet-port@0 {
+ phy-mode = "rgmii";
+ phy-handle = <&phy0>;
+ };
+ ethernet-port@1 {
+ /* Not used in this platform */
+ };
+ };
+
+ ide@63000000 {
+ status = "okay";
+ };
+
+ usb@69000000 {
+ status = "okay";
+ dr_mode = "peripheral";
+ usb-phy = <&usb1_phy>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_default_pins>;
+ };
+ };
+};
diff --git a/src/arm/gemini/gemini-nas4220b.dts b/src/arm/gemini/gemini-nas4220b.dts
new file mode 100644
index 0000000..6544c73
--- /dev/null
+++ b/src/arm/gemini/gemini-nas4220b.dts
@@ -0,0 +1,189 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for the Gemini-based Raidsonic NAS IB-4220-B
+ */
+
+/dts-v1/;
+
+#include "gemini.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Raidsonic NAS IB-4220-B";
+ compatible = "raidsonic,ib-4220-b", "cortina,gemini";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory@0 { /* 128 MB */
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,19200n8 root=/dev/mtdblock3 rw rootfstype=squashfs,jffs2 rootwait";
+ stdout-path = &uart0;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ button-setup {
+ debounce-interval = <100>;
+ wakeup-source;
+ linux,code = <KEY_SETUP>;
+ label = "Backup button";
+ /* Conflict with TVC */
+ gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
+ };
+ button-restart {
+ debounce-interval = <100>;
+ wakeup-source;
+ linux,code = <KEY_RESTART>;
+ label = "Softreset button";
+ /* Conflict with TVC */
+ gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led-orange-hdd {
+ label = "nas4220b:orange:hdd";
+ /* Conflict with TVC */
+ gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ led-green-os {
+ label = "nas4220b:green:os";
+ /* Conflict with TVC */
+ gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
+ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ soc {
+ flash@30000000 {
+ status = "okay";
+ /* 16MB of flash */
+ reg = <0x30000000 0x01000000>;
+
+ partitions {
+ compatible = "redboot-fis";
+ /* Eraseblock at 0xfe0000 */
+ fis-index-block = <0x7f>;
+ };
+ };
+
+ syscon: syscon@40000000 {
+ pinctrl {
+ /*
+ * gpio1dgrp cover line 28-31 otherwise used
+ * by TVC.
+ */
+ gpio1_default_pins: pinctrl-gpio1 {
+ mux {
+ function = "gpio1";
+ groups = "gpio1dgrp";
+ };
+ };
+ pinctrl-gmii {
+ mux {
+ function = "gmii";
+ groups = "gmii_gmac0_grp";
+ };
+ /* Settings come from OpenWRT, pins on SL3516 */
+ conf0 {
+ pins = "V8 GMAC0 RXDV", "T10 GMAC1 RXDV";
+ skew-delay = <0>;
+ };
+ conf1 {
+ pins = "Y7 GMAC0 RXC", "Y11 GMAC1 RXC";
+ skew-delay = <15>;
+ };
+ conf2 {
+ pins = "T8 GMAC0 TXEN", "W11 GMAC1 TXEN";
+ skew-delay = <7>;
+ };
+ conf3 {
+ pins = "U8 GMAC0 TXC";
+ skew-delay = <11>;
+ };
+ conf4 {
+ pins = "V11 GMAC1 TXC";
+ skew-delay = <10>;
+ };
+ conf5 {
+ /* The data lines all have default skew */
+ pins = "W8 GMAC0 RXD0", "V9 GMAC0 RXD1",
+ "Y8 GMAC0 RXD2", "U9 GMAC0 RXD3",
+ "T7 GMAC0 TXD0", "U6 GMAC0 TXD1",
+ "V7 GMAC0 TXD2", "U7 GMAC0 TXD3",
+ "Y12 GMAC1 RXD0", "V12 GMAC1 RXD1",
+ "T11 GMAC1 RXD2", "W12 GMAC1 RXD3",
+ "U10 GMAC1 TXD0", "Y10 GMAC1 TXD1",
+ "W10 GMAC1 TXD2", "T9 GMAC1 TXD3";
+ skew-delay = <7>;
+ };
+ /* Set up drive strength on GMAC0 to 16 mA */
+ conf6 {
+ groups = "gmii_gmac0_grp";
+ drive-strength = <16>;
+ };
+ };
+ };
+ };
+
+ sata: sata@46000000 {
+ cortina,gemini-ata-muxmode = <0>;
+ cortina,gemini-enable-sata-bridge;
+ status = "okay";
+ };
+
+ gpio1: gpio@4e000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio1_default_pins>;
+ };
+
+ ethernet@60000000 {
+ status = "okay";
+
+ ethernet-port@0 {
+ phy-mode = "rgmii";
+ phy-handle = <&phy0>;
+ };
+ ethernet-port@1 {
+ /* Not used in this platform */
+ };
+ };
+
+ ide@63000000 {
+ status = "okay";
+ };
+
+ ide@63400000 {
+ status = "okay";
+ };
+
+ usb@68000000 {
+ status = "okay";
+ };
+
+ usb@69000000 {
+ status = "okay";
+ };
+ };
+};
diff --git a/src/arm/gemini/gemini-ns2502.dts b/src/arm/gemini/gemini-ns2502.dts
new file mode 100644
index 0000000..e6eeb35
--- /dev/null
+++ b/src/arm/gemini/gemini-ns2502.dts
@@ -0,0 +1,123 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021 Corentin Labbe <clabbe@baylibre.com>
+ * Device Tree file for Edimax NS 2502
+ */
+
+/dts-v1/;
+
+#include "gemini.dtsi"
+
+/ {
+ model = "Edimax NS-2502";
+ compatible = "edimax,ns-2502", "cortina,gemini";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory@0 {
+ /* 128 MB */
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>;
+ };
+
+ aliases {
+ mdio-gpio0 = &mdio0;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,19200n8";
+ stdout-path = &uart0;
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
+ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ };
+};
+
+ðernet {
+ status = "okay";
+ ethernet-port@0 {
+ phy-mode = "rgmii-id";
+ phy-handle = <&phy0>;
+ };
+};
+
+&flash {
+ status = "okay";
+ /* 8MB of flash */
+ reg = <0x30000000 0x00800000>;
+
+ pinctrl-names = "enabled", "disabled";
+ pinctrl-0 = <&pflash_default_pins>;
+ pinctrl-1 = <&pflash_disabled_pins>;
+
+ partitions {
+ compatible = "redboot-fis";
+ /* Eraseblock at 0x7e0000 */
+ fis-index-block = <0x3f>;
+ };
+};
+
+&gpio0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio0_default_pins>;
+};
+
+&ide0 {
+ status = "okay";
+};
+
+&ide1 {
+ status = "okay";
+};
+
+&sata {
+ cortina,gemini-ata-muxmode = <3>;
+ cortina,gemini-enable-sata-bridge;
+ status = "okay";
+};
+
+&syscon {
+ pinctrl {
+ /*
+ * gpio0agrp cover line 0-4
+ * gpio0bgrp cover line 5
+ */
+ gpio0_default_pins: pinctrl-gpio0 {
+ mux {
+ function = "gpio0";
+ groups = "gpio0agrp", "gpio0bgrp", "gpio0hgrp";
+ };
+ };
+ pflash_disabled_pins: pinctrl-pflash-disabled {
+ mux {
+ function = "gpio0";
+ groups = "gpio0ggrp", "gpio0igrp", "gpio0jgrp",
+ "gpio0kgrp";
+ };
+ };
+ pinctrl-gmii {
+ mux {
+ function = "gmii";
+ groups = "gmii_gmac0_grp";
+ };
+ };
+ };
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
diff --git a/src/arm/gemini/gemini-rut1xx.dts b/src/arm/gemini/gemini-rut1xx.dts
new file mode 100644
index 0000000..0ebda4e
--- /dev/null
+++ b/src/arm/gemini/gemini-rut1xx.dts
@@ -0,0 +1,136 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for Teltonika RUT1xx
+ */
+
+/dts-v1/;
+
+#include "gemini.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Teltonika RUT1xx";
+ compatible = "teltonika,rut1xx", "cortina,gemini";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory@0 { /* 128 MB */
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ stdout-path = &uart0;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ button-setup {
+ debounce-interval = <100>;
+ wakeup-source;
+ linux,code = <KEY_SETUP>;
+ label = "Reset to defaults";
+ /* Conflict with TVC */
+ gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led-gsm {
+ /* FIXME: add the LED color */
+ label = "rut1xx::gsm";
+ /* Conflict with ICE */
+ gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ led-power {
+ /* FIXME: add the LED color */
+ label = "rut1xx::power";
+ /* Conflict with NAND CE0 */
+ gpios = <&gpio0 17 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
+ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ soc {
+ flash@30000000 {
+ status = "okay";
+ /* 8MB of flash */
+ reg = <0x30000000 0x00800000>;
+ /* TODO: add flash partitions here */
+ };
+
+ syscon: syscon@40000000 {
+ pinctrl {
+ /*
+ * gpio0bgrp cover line 7 used by GSM LED
+ * gpio0fgrp cover line 17 used by power LED
+ */
+ gpio0_default_pins: pinctrl-gpio0 {
+ mux {
+ function = "gpio0";
+ groups = "gpio0bgrp",
+ "gpio0fgrp";
+ };
+ };
+ /*
+ * gpio1dgrp cover line 28-31 otherwise used
+ * by TVC.
+ */
+ gpio1_default_pins: pinctrl-gpio1 {
+ mux {
+ function = "gpio1";
+ groups = "gpio1dgrp";
+ };
+ };
+ };
+ };
+
+ gpio0: gpio@4d000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio0_default_pins>;
+ };
+
+ gpio1: gpio@4e000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio1_default_pins>;
+ };
+
+ ethernet@60000000 {
+ status = "okay";
+
+ ethernet-port@0 {
+ phy-mode = "rgmii";
+ phy-handle = <&phy0>;
+ };
+ ethernet-port@1 {
+ /* Not used in this platform */
+ };
+ };
+
+ usb@68000000 {
+ status = "okay";
+ };
+
+ usb@69000000 {
+ status = "okay";
+ };
+ };
+};
diff --git a/src/arm/gemini/gemini-sl93512r.dts b/src/arm/gemini/gemini-sl93512r.dts
new file mode 100644
index 0000000..91c19e8
--- /dev/null
+++ b/src/arm/gemini/gemini-sl93512r.dts
@@ -0,0 +1,294 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for the Storm Semiconductor SL93512R_BRD
+ * Gemini reference design, also initially called
+ * "Gemini324 EV-Board" before Storm acquired Storlink Semiconductor.
+ * The series were later acquired by Cortina Systems.
+ */
+
+/dts-v1/;
+
+#include "gemini.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Storlink Semiconductor Gemini324 EV-Board / Storm Semiconductor SL93512R_BRD";
+ compatible = "storlink,gemini324", "storm,sl93512r", "cortina,gemini";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory@0 {
+ /* 64 MB Samsung K4H511638B */
+ device_type = "memory";
+ reg = <0x00000000 0x4000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,19200n8 root=/dev/mtdblock3 rw rootfstype=squashfs,jffs2 rootwait";
+ stdout-path = &uart0;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ button-wps {
+ debounce-interval = <50>;
+ wakeup-source;
+ linux,code = <KEY_WPS_BUTTON>;
+ label = "WPS";
+ /* Conflicts with TVC and extended flash */
+ gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
+ };
+
+ button-setup {
+ debounce-interval = <50>;
+ wakeup-source;
+ linux,code = <KEY_SETUP>;
+ label = "factory reset";
+ /* Conflict with NAND flash */
+ gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led-green-harddisk {
+ label = "sq201:green:harddisk";
+ /* Conflict with LCD (no problem) */
+ gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ linux,default-trigger = "disk-activity";
+ };
+ led-green-wireless {
+ label = "sq201:green:wireless";
+ /* Conflict with NAND flash CE0 (no problem) */
+ gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ /* Uses MDC and MDIO */
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
+ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* This is a Marvell 88E1111 ethernet transciever */
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ };
+ };
+
+ spi {
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ /* Check pin collisions */
+ sck-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ miso-gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+ mosi-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
+ num-chipselects = <1>;
+
+ switch@0 {
+ compatible = "vitesse,vsc7385";
+ reg = <0>;
+ /* Specified for 2.5 MHz or below */
+ spi-max-frequency = <2500000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+ vsc: port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac1>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+ };
+ };
+
+
+ soc {
+ flash@30000000 {
+ status = "okay";
+ /* 16MB of flash */
+ reg = <0x30000000 0x01000000>;
+
+ partitions {
+ compatible = "redboot-fis";
+ /* Eraseblock at 0xfe0000 */
+ fis-index-block = <0x1fc>;
+ };
+ };
+
+ syscon: syscon@40000000 {
+ pinctrl {
+ /*
+ * gpio0agrp cover line 0, used by WPS button
+ * gpio0fgrp cover line 16 used by HD LED
+ * gpio0ggrp cover line 17, 18 used by wireless LAN LED and
+ * reset button OR USB ID select on 17 and USB VBUS select
+ * on 18. (Confusing.)
+ * gpio0igrp cover line 21, 22 used by MDIO for Marvell PHY
+ */
+ gpio0_default_pins: pinctrl-gpio0 {
+ mux {
+ function = "gpio0";
+ groups = "gpio0agrp",
+ "gpio0fgrp",
+ "gpio0ggrp",
+ "gpio0igrp";
+ };
+ };
+ /*
+ * gpio1dgrp cover lines used by SPI for
+ * the Vitesse chip (28-31)
+ */
+ gpio1_default_pins: pinctrl-gpio1 {
+ mux {
+ function = "gpio1";
+ groups = "gpio1dgrp";
+ };
+ };
+ pinctrl-gmii {
+ mux {
+ function = "gmii";
+ groups = "gmii_gmac0_grp", "gmii_gmac1_grp";
+ };
+ /* Control pad skew comes from sl_switch.c in the vendor code */
+ conf0 {
+ pins = "P10 GMAC1 TXC";
+ skew-delay = <5>;
+ };
+ conf1 {
+ pins = "V11 GMAC1 TXEN";
+ skew-delay = <7>;
+ };
+ conf2 {
+ pins = "T11 GMAC1 RXC";
+ skew-delay = <8>;
+ };
+ conf3 {
+ pins = "U11 GMAC1 RXDV";
+ skew-delay = <7>;
+ };
+ conf4 {
+ pins = "V7 GMAC0 TXC";
+ skew-delay = <10>;
+ };
+ conf5 {
+ pins = "P8 GMAC0 TXEN";
+ skew-delay = <7>; /* 5 at another place? */
+ };
+ conf6 {
+ pins = "T8 GMAC0 RXC";
+ skew-delay = <15>;
+ };
+ conf7 {
+ pins = "R8 GMAC0 RXDV";
+ skew-delay = <0>;
+ };
+ conf8 {
+ /* The data lines all have default skew */
+ pins = "U8 GMAC0 RXD0", "V8 GMAC0 RXD1",
+ "P9 GMAC0 RXD2", "R9 GMAC0 RXD3",
+ "R11 GMAC1 RXD0", "P11 GMAC1 RXD1",
+ "V12 GMAC1 RXD2", "U12 GMAC1 RXD3",
+ "R10 GMAC1 TXD0", "T10 GMAC1 TXD1",
+ "U10 GMAC1 TXD2", "V10 GMAC1 TXD3";
+ skew-delay = <7>;
+ };
+ /* Appears in sl351x_gmac.c in the vendor code */
+ conf9 {
+ pins = "U7 GMAC0 TXD0", "T7 GMAC0 TXD1",
+ "R7 GMAC0 TXD2", "P7 GMAC0 TXD3";
+ skew-delay = <5>;
+ };
+ };
+ };
+ };
+
+ /* Both interfaces brought out on SATA connectors */
+ sata: sata@46000000 {
+ cortina,gemini-ata-muxmode = <0>;
+ cortina,gemini-enable-sata-bridge;
+ status = "okay";
+ };
+
+ gpio0: gpio@4d000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio0_default_pins>;
+ };
+
+ gpio1: gpio@4e000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio1_default_pins>;
+ };
+
+ pci@50000000 {
+ status = "okay";
+ };
+
+ ethernet@60000000 {
+ status = "okay";
+
+ ethernet-port@0 {
+ phy-mode = "rgmii";
+ phy-handle = <&phy0>;
+ };
+ ethernet-port@1 {
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+
+ ide@63000000 {
+ status = "okay";
+ };
+
+ ide@63400000 {
+ status = "okay";
+ };
+
+ usb@68000000 {
+ status = "okay";
+ };
+
+ usb@69000000 {
+ status = "okay";
+ };
+ };
+};
diff --git a/src/arm/gemini/gemini-sq201.dts b/src/arm/gemini/gemini-sq201.dts
new file mode 100644
index 0000000..d0efd76
--- /dev/null
+++ b/src/arm/gemini/gemini-sq201.dts
@@ -0,0 +1,286 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for ITian Square One SQ201 NAS
+ */
+
+/dts-v1/;
+
+#include "gemini.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "ITian Square One SQ201";
+ compatible = "itian,sq201", "cortina,gemini";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory@0 { /* 128 MB */
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait";
+ stdout-path = &uart0;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ button-setup {
+ debounce-interval = <100>;
+ wakeup-source;
+ linux,code = <KEY_SETUP>;
+ label = "factory reset";
+ /* Conflict with NAND flash */
+ gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led-green-info {
+ label = "sq201:green:info";
+ gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+ led-green-usb {
+ label = "sq201:green:usb";
+ gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ linux,default-trigger = "usb-host";
+ };
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ /* Uses MDC and MDIO */
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
+ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* This is a Marvell 88E1111 ethernet transciever */
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ };
+ };
+
+ spi {
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ /* Check pin collisions */
+ sck-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ miso-gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+ mosi-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
+ num-chipselects = <1>;
+
+ switch@0 {
+ compatible = "vitesse,vsc7395";
+ reg = <0>;
+ /* Specified for 2.5 MHz or below */
+ spi-max-frequency = <2500000>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+ vsc: port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac1>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+ };
+ };
+
+
+ soc {
+ flash@30000000 {
+ status = "okay";
+ pinctrl-names = "enabled", "disabled";
+ pinctrl-0 = <&pflash_default_pins>;
+ pinctrl-1 = <&pflash_disabled_pins>;
+ /* 16MB of flash */
+ reg = <0x30000000 0x01000000>;
+
+ partitions {
+ compatible = "redboot-fis";
+ /* Eraseblock at 0xfe0000 */
+ fis-index-block = <0x1fc>;
+ };
+ };
+
+ syscon: syscon@40000000 {
+ pinctrl {
+ /*
+ * gpio0fgrp cover line 18 used by reset button
+ * gpio0ggrp cover line 20 used by info LED
+ * gpio0hgrp cover line 21, 22 used by MDIO for Marvell PHY
+ * gpio0kgrp cover line 31 used by USB LED
+ */
+ gpio0_default_pins: pinctrl-gpio0 {
+ mux {
+ function = "gpio0";
+ groups = "gpio0fgrp",
+ "gpio0hgrp";
+ };
+ };
+ /*
+ * gpio0dgrp cover lines used by the SPI
+ * to the Vitesse G5x chip.
+ */
+ gpio1_default_pins: pinctrl-gpio1 {
+ mux {
+ function = "gpio1";
+ groups = "gpio1dgrp";
+ };
+ };
+ /*
+ * These GPIO groups will be mapped in over some
+ * of the flash pins when the flash is not in
+ * active use.
+ */
+ pflash_disabled_pins: pinctrl-pflash-disabled {
+ mux {
+ function = "gpio0";
+ groups = "gpio0ggrp", "gpio0igrp", "gpio0jgrp",
+ "gpio0kgrp";
+ };
+ };
+ pinctrl-gmii {
+ mux {
+ function = "gmii";
+ groups = "gmii_gmac0_grp", "gmii_gmac1_grp";
+ };
+ /* Settings come from memory dump in PLATO */
+ conf0 {
+ pins = "V8 GMAC0 RXDV";
+ skew-delay = <0>;
+ };
+ conf1 {
+ pins = "Y7 GMAC0 RXC";
+ skew-delay = <15>;
+ };
+ conf2 {
+ pins = "T8 GMAC0 TXEN";
+ skew-delay = <7>;
+ };
+ conf3 {
+ pins = "U8 GMAC0 TXC";
+ skew-delay = <10>;
+ };
+ conf4 {
+ pins = "T10 GMAC1 RXDV";
+ skew-delay = <7>;
+ };
+ conf5 {
+ pins = "Y11 GMAC1 RXC";
+ skew-delay = <8>;
+ };
+ conf6 {
+ pins = "W11 GMAC1 TXEN";
+ skew-delay = <7>;
+ };
+ conf7 {
+ pins = "V11 GMAC1 TXC";
+ skew-delay = <5>;
+ };
+ conf8 {
+ /* The data lines all have default skew */
+ pins = "W8 GMAC0 RXD0", "V9 GMAC0 RXD1",
+ "Y8 GMAC0 RXD2", "U9 GMAC0 RXD3",
+ "T7 GMAC0 TXD0", "U6 GMAC0 TXD1",
+ "V7 GMAC0 TXD2", "U7 GMAC0 TXD3",
+ "Y12 GMAC1 RXD0", "V12 GMAC1 RXD1",
+ "T11 GMAC1 RXD2", "W12 GMAC1 RXD3",
+ "U10 GMAC1 TXD0", "Y10 GMAC1 TXD1",
+ "W10 GMAC1 TXD2", "T9 GMAC1 TXD3";
+ skew-delay = <7>;
+ };
+ /* Set up drive strength on GMAC0 and GMAC1 to 16 mA */
+ conf9 {
+ groups = "gmii_gmac0_grp", "gmii_gmac1_grp";
+ drive-strength = <16>;
+ };
+ };
+ };
+ };
+
+ sata: sata@46000000 {
+ cortina,gemini-ata-muxmode = <0>;
+ cortina,gemini-enable-sata-bridge;
+ status = "okay";
+ };
+
+ gpio0: gpio@4d000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio0_default_pins>;
+ };
+
+ gpio1: gpio@4e000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio1_default_pins>;
+ };
+
+ pci@50000000 {
+ status = "okay";
+ };
+
+ ethernet@60000000 {
+ status = "okay";
+
+ ethernet-port@0 {
+ phy-mode = "rgmii";
+ phy-handle = <&phy0>;
+ };
+ ethernet-port@1 {
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+
+ ide@63000000 {
+ status = "okay";
+ };
+
+ usb@68000000 {
+ status = "okay";
+ };
+
+ usb@69000000 {
+ status = "okay";
+ };
+ };
+};
diff --git a/src/arm/gemini/gemini-ssi1328.dts b/src/arm/gemini/gemini-ssi1328.dts
new file mode 100644
index 0000000..42e85f0
--- /dev/null
+++ b/src/arm/gemini/gemini-ssi1328.dts
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021 Corentin Labbe <clabbe@baylibre.com>
+ * Device Tree file for SSI 1328
+ */
+
+/dts-v1/;
+
+#include "gemini.dtsi"
+
+/ {
+ model = "SSI 1328";
+ compatible = "ssi,1328", "cortina,gemini";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory@0 {
+ /* 128 MB */
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>;
+ };
+
+ aliases {
+ mdio-gpio0 = &mdio0;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,19200n8 initrd=0x900000,9M";
+ stdout-path = &uart0;
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
+ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* LAN Marvell 88E1118 */
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ /* WAN ICPlus IP101A */
+ phy1: ethernet-phy@2 {
+ reg = <2>;
+ device_type = "ethernet-phy";
+ };
+ };
+};
+
+ðernet {
+ status = "okay";
+ ethernet-port@0 {
+ phy-mode = "rgmii";
+ phy-handle = <&phy0>;
+ };
+ ethernet-port@1 {
+ phy-mode = "rgmii";
+ phy-handle = <&phy1>;
+ };
+};
+
+&flash {
+ status = "okay";
+ /* 32MB of flash */
+ reg = <0x30000000 0x03200000>;
+
+ pinctrl-names = "enabled", "disabled";
+ pinctrl-0 = <&pflash_default_pins>;
+ pinctrl-1 = <&pflash_disabled_pins>;
+
+ partitions {
+ compatible = "redboot-fis";
+ /* Eraseblock at 0xfe0000 */
+ fis-index-block = <0x7F>;
+ };
+};
+
+&gpio0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio0_default_pins>;
+};
+
+&ide0 {
+ status = "okay";
+};
+
+&ide1 {
+ status = "okay";
+};
+
+&sata {
+ cortina,gemini-ata-muxmode = <0>;
+ cortina,gemini-enable-sata-bridge;
+ status = "okay";
+};
+
+&syscon {
+ pinctrl {
+ /*
+ * gpio0agrp cover line 0-4
+ * gpio0bgrp cover line 5
+ */
+ gpio0_default_pins: pinctrl-gpio0 {
+ mux {
+ function = "gpio0";
+ groups = "gpio0agrp", "gpio0bgrp";
+ };
+ };
+ pflash_disabled_pins: pinctrl-pflash-disabled {
+ mux {
+ function = "gpio0";
+ groups = "gpio0ggrp", "gpio0igrp", "gpio0jgrp",
+ "gpio0kgrp";
+ };
+ };
+ pinctrl-gmii {
+ /* This platform use both the ethernet ports */
+ mux {
+ function = "gmii";
+ groups = "gmii_gmac0_grp", "gmii_gmac1_grp";
+ };
+ };
+ };
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
diff --git a/src/arm/gemini/gemini-wbd111.dts b/src/arm/gemini/gemini-wbd111.dts
new file mode 100644
index 0000000..3c88c59
--- /dev/null
+++ b/src/arm/gemini/gemini-wbd111.dts
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for Wiliboard WBD-111
+ */
+
+/dts-v1/;
+
+#include "gemini.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Wiliboard WBD-111";
+ compatible = "wiliboard,wbd111", "cortina,gemini";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory@0 {
+ /* 128 MB */
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ stdout-path = &uart0;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ button-setup {
+ debounce-interval = <100>;
+ wakeup-source;
+ linux,code = <KEY_SETUP>;
+ label = "reset";
+ /* Conflict with ICE */
+ gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-red-l3 {
+ label = "wbd111:red:L3";
+ /* Conflict with TVC and extended parallel flash */
+ gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led-green-l4 {
+ label = "wbd111:green:L4";
+ /* Conflict with TVC and extended parallel flash */
+ gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led-red-l4 {
+ label = "wbd111:red:L4";
+ /* Conflict with TVC and extended parallel flash */
+ gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led-greeb-l3 {
+ label = "wbd111:green:L3";
+ /* Conflict with TVC and extended parallel flash */
+ gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
+ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ soc {
+ flash@30000000 {
+ status = "okay";
+ /* 8MB of flash */
+ reg = <0x30000000 0x00800000>;
+
+ partitions {
+ compatible = "redboot-fis";
+ /* Eraseblock at 0x7e0000 */
+ fis-index-block = <0x3f>;
+ };
+ };
+
+ syscon: syscon@40000000 {
+ pinctrl {
+ /*
+ * gpio0agrp cover line 0-4
+ * gpio0bgrp cover line 5
+ */
+ gpio0_default_pins: pinctrl-gpio0 {
+ mux {
+ function = "gpio0";
+ groups = "gpio0agrp",
+ "gpio0bgrp";
+ };
+ };
+ };
+ };
+
+ gpio0: gpio@4d000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio0_default_pins>;
+ };
+
+ pci@50000000 {
+ status = "okay";
+ };
+
+ ethernet@60000000 {
+ status = "okay";
+
+ ethernet-port@0 {
+ phy-mode = "rgmii";
+ phy-handle = <&phy0>;
+ };
+ ethernet-port@1 {
+ /* Not used in this platform */
+ };
+ };
+
+ usb@68000000 {
+ status = "okay";
+ };
+
+ usb@69000000 {
+ status = "okay";
+ };
+ };
+};
diff --git a/src/arm/gemini/gemini-wbd222.dts b/src/arm/gemini/gemini-wbd222.dts
new file mode 100644
index 0000000..ff72bbc
--- /dev/null
+++ b/src/arm/gemini/gemini-wbd222.dts
@@ -0,0 +1,154 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for Wiliboard WBD-222
+ */
+
+/dts-v1/;
+
+#include "gemini.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Wiliboard WBD-222";
+ compatible = "wiliboard,wbd222", "cortina,gemini";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ memory@0 { /* 128 MB */
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ stdout-path = &uart0;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ button-setup {
+ debounce-interval = <100>;
+ wakeup-source;
+ linux,code = <KEY_SETUP>;
+ label = "reset";
+ /* Conflict with ICE */
+ gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-red-l3 {
+ label = "wbd111:red:L3";
+ /* Conflict with TVC and extended parallel flash */
+ gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led-green-l4 {
+ label = "wbd111:green:L4";
+ /* Conflict with TVC and extended parallel flash */
+ gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led-red-l4 {
+ label = "wbd111:red:L4";
+ /* Conflict with TVC and extended parallel flash */
+ gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ led-green-l3 {
+ label = "wbd111:green:L3";
+ /* Conflict with TVC and extended parallel flash */
+ gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
+ <&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+
+ phy1: ethernet-phy@3 {
+ reg = <3>;
+ device_type = "ethernet-phy";
+ };
+ };
+
+ soc {
+ flash@30000000 {
+ status = "okay";
+ /* 8MB of flash */
+ reg = <0x30000000 0x00800000>;
+
+ partitions {
+ compatible = "redboot-fis";
+ /* Eraseblock at 0x7e0000 */
+ fis-index-block = <0x3f>;
+ };
+ };
+
+ syscon: syscon@40000000 {
+ pinctrl {
+ /*
+ * gpio0agrp cover line 0-4
+ * gpio0bgrp cover line 5
+ */
+ gpio0_default_pins: pinctrl-gpio0 {
+ mux {
+ function = "gpio0";
+ groups = "gpio0agrp",
+ "gpio0bgrp";
+ };
+ };
+ pinctrl-gmii {
+ /* This platform use both the ethernet ports */
+ mux {
+ function = "gmii";
+ groups = "gmii_gmac0_grp", "gmii_gmac1_grp";
+ };
+ };
+ };
+ };
+
+ gpio0: gpio@4d000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio0_default_pins>;
+ };
+
+ pci@50000000 {
+ status = "okay";
+ };
+
+ ethernet@60000000 {
+ status = "okay";
+
+ ethernet-port@0 {
+ phy-mode = "rgmii";
+ phy-handle = <&phy0>;
+ };
+ ethernet-port@1 {
+ phy-mode = "rgmii";
+ phy-handle = <&phy1>;
+ };
+ };
+
+ usb@68000000 {
+ status = "okay";
+ };
+
+ usb@69000000 {
+ status = "okay";
+ };
+ };
+};
diff --git a/src/arm/gemini/gemini.dtsi b/src/arm/gemini/gemini.dtsi
new file mode 100644
index 0000000..befe322
--- /dev/null
+++ b/src/arm/gemini/gemini.dtsi
@@ -0,0 +1,475 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for Cortina systems Gemini SoC
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/clock/cortina,gemini-clock.h>
+#include <dt-bindings/reset/cortina,gemini-reset.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ compatible = "simple-bus";
+ interrupt-parent = <&intcon>;
+
+ flash: flash@30000000 {
+ compatible = "cortina,gemini-flash", "cfi-flash";
+ syscon = <&syscon>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pflash_default_pins>;
+ bank-width = <2>;
+ status = "disabled";
+ };
+
+ syscon: syscon@40000000 {
+ compatible = "cortina,gemini-syscon",
+ "syscon", "simple-mfd";
+ reg = <0x40000000 0x1000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+
+ syscon-reboot {
+ compatible = "syscon-reboot";
+ regmap = <&syscon>;
+ /* GLOBAL_RESET register */
+ offset = <0x0c>;
+ /* RESET_GLOBAL | RESET_CPU1 */
+ mask = <0xC0000000>;
+ };
+
+ pinctrl {
+ compatible = "cortina,gemini-pinctrl";
+ regmap = <&syscon>;
+ /* Hog the DRAM pins */
+ pinctrl-names = "default";
+ pinctrl-0 = <&dram_default_pins>, <&system_default_pins>,
+ <&vcontrol_default_pins>;
+
+ dram_default_pins: pinctrl-dram {
+ mux {
+ function = "dram";
+ groups = "dramgrp";
+ };
+ };
+ rtc_default_pins: pinctrl-rtc {
+ mux {
+ function = "rtc";
+ groups = "rtcgrp";
+ };
+ };
+ power_default_pins: pinctrl-power {
+ mux {
+ function = "power";
+ groups = "powergrp";
+ };
+ };
+ cir_default_pins: pinctrl-cir {
+ mux {
+ function = "cir";
+ groups = "cirgrp";
+ };
+ };
+ system_default_pins: pinctrl-system {
+ mux {
+ function = "system";
+ groups = "systemgrp";
+ };
+ };
+ vcontrol_default_pins: pinctrl-vcontrol {
+ mux {
+ function = "vcontrol";
+ groups = "vcontrolgrp";
+ };
+ };
+ ice_default_pins: pinctrl-ice {
+ mux {
+ function = "ice";
+ groups = "icegrp";
+ };
+ };
+ uart_default_pins: pinctrl-uart {
+ mux {
+ function = "uart";
+ groups = "uartrxtxgrp";
+ };
+ };
+ pflash_default_pins: pinctrl-pflash {
+ mux {
+ function = "pflash";
+ groups = "pflashgrp";
+ };
+ };
+ usb_default_pins: pinctrl-usb {
+ mux {
+ function = "usb";
+ groups = "usbgrp";
+ };
+ };
+ gmii_default_pins: pinctrl-gmii {
+ /*
+ * Only activate GMAC0 by default since
+ * GMAC1 will overlap with 8 GPIO lines
+ * gpio2a, gpio2b. Overlay groups with
+ * "gmii_gmac0_grp", "gmii_gmac1_grp" for
+ * both ethernet interfaces.
+ */
+ mux {
+ function = "gmii";
+ groups = "gmii_gmac0_grp";
+ };
+ };
+ pci_default_pins: pinctrl-pci {
+ mux {
+ function = "pci";
+ groups = "pcigrp";
+ };
+ };
+ sata_default_pins: pinctrl-sata {
+ mux {
+ function = "sata";
+ groups = "satagrp";
+ };
+ };
+ /* Activate both groups of pins for this state */
+ sata_and_ide_pins: pinctrl-sata-ide {
+ mux0 {
+ function = "sata";
+ groups = "satagrp";
+ };
+ mux1 {
+ function = "ide";
+ groups = "idegrp";
+ };
+ };
+ tvc_default_pins: pinctrl-tvc {
+ mux {
+ function = "tvc";
+ groups = "tvcgrp";
+ };
+ };
+ };
+ };
+
+ watchdog@41000000 {
+ compatible = "cortina,gemini-watchdog", "faraday,ftwdt010";
+ reg = <0x41000000 0x1000>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&syscon GEMINI_RESET_WDOG>;
+ clocks = <&syscon GEMINI_CLK_APB>;
+ clock-names = "PCLK";
+ };
+
+ uart0: serial@42000000 {
+ compatible = "ns16550a";
+ reg = <0x42000000 0x100>;
+ resets = <&syscon GEMINI_RESET_UART>;
+ clocks = <&syscon GEMINI_CLK_UART>;
+ interrupts = <18 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart_default_pins>;
+ reg-shift = <2>;
+ };
+
+ timer@43000000 {
+ compatible = "faraday,fttmr010";
+ reg = <0x43000000 0x1000>;
+ interrupt-parent = <&intcon>;
+ interrupts = <14 IRQ_TYPE_EDGE_FALLING>, /* Timer 1 */
+ <15 IRQ_TYPE_EDGE_FALLING>, /* Timer 2 */
+ <16 IRQ_TYPE_EDGE_FALLING>; /* Timer 3 */
+ resets = <&syscon GEMINI_RESET_TIMER>;
+ /* APB clock or RTC clock */
+ clocks = <&syscon GEMINI_CLK_APB>, <&syscon GEMINI_CLK_RTC>;
+ clock-names = "PCLK", "EXTCLK";
+ syscon = <&syscon>;
+ };
+
+ rtc@45000000 {
+ compatible = "cortina,gemini-rtc", "faraday,ftrtc010";
+ reg = <0x45000000 0x100>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&syscon GEMINI_RESET_RTC>;
+ clocks = <&syscon GEMINI_CLK_APB>, <&syscon GEMINI_CLK_RTC>;
+ clock-names = "PCLK", "EXTCLK";
+ pinctrl-names = "default";
+ pinctrl-0 = <&rtc_default_pins>;
+ };
+
+ sata: sata@46000000 {
+ compatible = "cortina,gemini-sata-bridge";
+ reg = <0x46000000 0x100>;
+ resets = <&syscon GEMINI_RESET_SATA0>,
+ <&syscon GEMINI_RESET_SATA1>;
+ reset-names = "sata0", "sata1";
+ clocks = <&syscon GEMINI_CLK_GATE_SATA0>,
+ <&syscon GEMINI_CLK_GATE_SATA1>;
+ clock-names = "SATA0_PCLK", "SATA1_PCLK";
+ /*
+ * This defines the special "ide" state that needs
+ * to be explicitly enabled to enable the IDE pins,
+ * as these pins are normally used for other things.
+ */
+ pinctrl-names = "default", "ide";
+ pinctrl-0 = <&sata_default_pins>;
+ pinctrl-1 = <&sata_and_ide_pins>;
+ syscon = <&syscon>;
+ status = "disabled";
+ };
+
+ intcon: interrupt-controller@48000000 {
+ compatible = "faraday,ftintc010";
+ reg = <0x48000000 0x1000>;
+ resets = <&syscon GEMINI_RESET_INTCON0>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ power-controller@4b000000 {
+ compatible = "cortina,gemini-power-controller";
+ reg = <0x4b000000 0x100>;
+ interrupts = <26 IRQ_TYPE_EDGE_RISING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&power_default_pins>;
+ };
+
+ gpio0: gpio@4d000000 {
+ compatible = "cortina,gemini-gpio", "faraday,ftgpio010";
+ reg = <0x4d000000 0x100>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&syscon GEMINI_RESET_GPIO0>;
+ clocks = <&syscon GEMINI_CLK_APB>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio1: gpio@4e000000 {
+ compatible = "cortina,gemini-gpio", "faraday,ftgpio010";
+ reg = <0x4e000000 0x100>;
+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&syscon GEMINI_RESET_GPIO1>;
+ clocks = <&syscon GEMINI_CLK_APB>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio@4f000000 {
+ compatible = "cortina,gemini-gpio", "faraday,ftgpio010";
+ reg = <0x4f000000 0x100>;
+ interrupts = <24 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&syscon GEMINI_RESET_GPIO2>;
+ clocks = <&syscon GEMINI_CLK_APB>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ pci@50000000 {
+ compatible = "cortina,gemini-pci", "faraday,ftpci100";
+ /*
+ * The first 256 bytes in the IO range is actually used
+ * to configure the host bridge.
+ */
+ reg = <0x50000000 0x100>;
+ resets = <&syscon GEMINI_RESET_PCI>;
+ clocks = <&syscon GEMINI_CLK_GATE_PCI>, <&syscon GEMINI_CLK_PCI>;
+ clock-names = "PCLK", "PCICLK";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pci_default_pins>;
+ device_type = "pci";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ status = "disabled";
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map =
+ <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
+ <0x4800 0 0 2 &pci_intc 1>,
+ <0x4800 0 0 3 &pci_intc 2>,
+ <0x4800 0 0 4 &pci_intc 3>,
+ <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
+ <0x5000 0 0 2 &pci_intc 2>,
+ <0x5000 0 0 3 &pci_intc 3>,
+ <0x5000 0 0 4 &pci_intc 0>,
+ <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
+ <0x5800 0 0 2 &pci_intc 3>,
+ <0x5800 0 0 3 &pci_intc 0>,
+ <0x5800 0 0 4 &pci_intc 1>,
+ <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
+ <0x6000 0 0 2 &pci_intc 0>,
+ <0x6000 0 0 3 &pci_intc 1>,
+ <0x6000 0 0 4 &pci_intc 2>;
+
+ bus-range = <0x00 0xff>;
+ /* PCI ranges mappings */
+ ranges =
+ /* 1MiB I/O space 0x50000000-0x500fffff */
+ <0x01000000 0 0 0x50000000 0 0x00100000>,
+ /* 128MiB non-prefetchable memory 0x58000000-0x5fffffff */
+ <0x02000000 0 0x58000000 0x58000000 0 0x08000000>;
+
+ /* DMA ranges */
+ dma-ranges =
+ /* 128MiB at 0x00000000-0x07ffffff */
+ <0x02000000 0 0x00000000 0x00000000 0 0x08000000>,
+ /* 64MiB at 0x00000000-0x03ffffff */
+ <0x02000000 0 0x00000000 0x00000000 0 0x04000000>,
+ /* 64MiB at 0x00000000-0x03ffffff */
+ <0x02000000 0 0x00000000 0x00000000 0 0x04000000>;
+
+ /*
+ * This PCI host bridge variant has a cascaded interrupt
+ * controller embedded in the host bridge.
+ */
+ pci_intc: interrupt-controller {
+ interrupt-parent = <&intcon>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ };
+ };
+
+ ethernet: ethernet@60000000 {
+ compatible = "cortina,gemini-ethernet";
+ reg = <0x60000000 0x4000>, /* Global registers, queue */
+ <0x60004000 0x2000>, /* V-bit */
+ <0x60006000 0x2000>; /* A-bit */
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmii_default_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ gmac0: ethernet-port@0 {
+ compatible = "cortina,gemini-ethernet-port";
+ reg = <0x60008000 0x2000>, /* Port 0 DMA/TOE */
+ <0x6000a000 0x2000>; /* Port 0 GMAC */
+ interrupt-parent = <&intcon>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&syscon GEMINI_RESET_GMAC0>;
+ clocks = <&syscon GEMINI_CLK_GATE_GMAC0>;
+ clock-names = "PCLK";
+ };
+
+ gmac1: ethernet-port@1 {
+ compatible = "cortina,gemini-ethernet-port";
+ reg = <0x6000c000 0x2000>, /* Port 1 DMA/TOE */
+ <0x6000e000 0x2000>; /* Port 1 GMAC */
+ interrupt-parent = <&intcon>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&syscon GEMINI_RESET_GMAC1>;
+ clocks = <&syscon GEMINI_CLK_GATE_GMAC1>;
+ clock-names = "PCLK";
+ };
+ };
+
+ crypto: crypto@62000000 {
+ compatible = "cortina,sl3516-crypto";
+ reg = <0x62000000 0x10000>;
+ interrupts = <7 IRQ_TYPE_EDGE_RISING>;
+ resets = <&syscon GEMINI_RESET_SECURITY>;
+ clocks = <&syscon GEMINI_CLK_GATE_SECURITY>;
+ };
+
+ ide0: ide@63000000 {
+ compatible = "cortina,gemini-pata", "faraday,ftide010";
+ reg = <0x63000000 0x1000>;
+ interrupts = <4 IRQ_TYPE_EDGE_RISING>;
+ resets = <&syscon GEMINI_RESET_IDE>;
+ clocks = <&syscon GEMINI_CLK_GATE_IDE>;
+ clock-names = "PCLK";
+ sata = <&sata>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ ide1: ide@63400000 {
+ compatible = "cortina,gemini-pata", "faraday,ftide010";
+ reg = <0x63400000 0x1000>;
+ interrupts = <5 IRQ_TYPE_EDGE_RISING>;
+ resets = <&syscon GEMINI_RESET_IDE>;
+ clocks = <&syscon GEMINI_CLK_GATE_IDE>;
+ clock-names = "PCLK";
+ sata = <&sata>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ dma-controller@67000000 {
+ compatible = "faraday,ftdma020", "arm,pl080", "arm,primecell";
+ /* Faraday Technology FTDMAC020 variant */
+ arm,primecell-periphid = <0x0003b080>;
+ reg = <0x67000000 0x1000>;
+ interrupts = <9 IRQ_TYPE_EDGE_RISING>;
+ resets = <&syscon GEMINI_RESET_DMAC>;
+ clocks = <&syscon GEMINI_CLK_AHB>;
+ clock-names = "apb_pclk";
+ /* Bus interface AHB1 (AHB0) is totally tilted */
+ lli-bus-interface-ahb2;
+ mem-bus-interface-ahb2;
+ memcpy-burst-size = <256>;
+ memcpy-bus-width = <32>;
+ #dma-cells = <2>;
+ };
+
+ display-controller@6a000000 {
+ compatible = "cortina,gemini-tvc", "faraday,tve200";
+ reg = <0x6a000000 0x1000>;
+ interrupts = <13 IRQ_TYPE_EDGE_RISING>;
+ resets = <&syscon GEMINI_RESET_TVC>;
+ clocks = <&syscon GEMINI_CLK_GATE_TVC>,
+ <&syscon GEMINI_CLK_TVC>;
+ clock-names = "PCLK", "TVE";
+ pinctrl-names = "default";
+ pinctrl-0 = <&tvc_default_pins>;
+ status = "disabled";
+ };
+
+ usb0: usb@68000000 {
+ compatible = "cortina,gemini-usb", "faraday,fotg200";
+ reg = <0x68000000 0x1000>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&syscon GEMINI_RESET_USB0>;
+ clocks = <&syscon GEMINI_CLK_GATE_USB0>;
+ clock-names = "PCLK";
+ /*
+ * This will claim pins for USB0 and USB1 at the same
+ * time as they are using some common pins. If you for
+ * some reason have a system using USB1 at 96000000 but
+ * NOT using USB0 at 68000000 you wll have to add the
+ * usb_default_pins to the USB controller at 96000000
+ * in your .dts for the board.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_default_pins>;
+ /* Default to host mode */
+ dr_mode = "host";
+ syscon = <&syscon>;
+ status = "disabled";
+ };
+
+ usb1: usb@69000000 {
+ compatible = "cortina,gemini-usb", "faraday,fotg200";
+ reg = <0x69000000 0x1000>;
+ interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&syscon GEMINI_RESET_USB1>;
+ clocks = <&syscon GEMINI_CLK_GATE_USB1>;
+ clock-names = "PCLK";
+ syscon = <&syscon>;
+ status = "disabled";
+ };
+ };
+};