Squashed 'dts/upstream/' content from commit aaba2d45dc2a
git-subtree-dir: dts/upstream
git-subtree-split: aaba2d45dc2a1b3bbb710f2a3808ee1c9f340abe
diff --git a/Bindings/phy/phy-stm32-usbphyc.yaml b/Bindings/phy/phy-stm32-usbphyc.yaml
new file mode 100644
index 0000000..24a3dbd
--- /dev/null
+++ b/Bindings/phy/phy-stm32-usbphyc.yaml
@@ -0,0 +1,282 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/phy-stm32-usbphyc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics STM32 USB HS PHY controller
+
+description:
+
+ The STM32 USBPHYC block contains a dual port High Speed UTMI+ PHY and a UTMI
+ switch. It controls PHY configuration and status, and the UTMI+ switch that
+ selects either OTG or HOST controller for the second PHY port. It also sets
+ PLL configuration.
+
+ USBPHYC
+ |_ PLL
+ |
+ |_ PHY port#1 _________________ HOST controller
+ | __ |
+ | / 1|________________|
+ |_ PHY port#2 ----| |________________
+ | \_0| |
+ |_ UTMI switch_______| OTG controller
+
+maintainers:
+ - Amelie Delaunay <amelie.delaunay@foss.st.com>
+
+properties:
+ compatible:
+ const: st,stm32mp1-usbphyc
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 0
+
+ vdda1v1-supply:
+ description: regulator providing 1V1 power supply to the PLL block
+
+ vdda1v8-supply:
+ description: regulator providing 1V8 power supply to the PLL block
+
+ '#clock-cells':
+ description: number of clock cells for ck_usbo_48m consumer
+ const: 0
+
+# Required child nodes:
+
+patternProperties:
+ "^usb-phy@[0|1]$":
+ type: object
+ description:
+ Each port the controller provides must be represented as a sub-node.
+
+ properties:
+ reg:
+ description: phy port index.
+ maxItems: 1
+
+ phy-supply:
+ description: regulator providing 3V3 power supply to the PHY.
+
+ "#phy-cells":
+ enum: [ 0x0, 0x1 ]
+
+ connector:
+ type: object
+ $ref: /schemas/connector/usb-connector.yaml
+ unevaluatedProperties: false
+
+ properties:
+ vbus-supply: true
+
+ # It can be necessary to adjust the PHY settings to compensate parasitics, which can be due
+ # to USB connector/receptacle, routing, ESD protection component,... Here is the list of
+ # all optional parameters to tune the interface of the PHY (HS for High-Speed, FS for Full-
+ # Speed, LS for Low-Speed)
+
+ st,current-boost-microamp:
+ description: Current boosting in uA
+ enum: [ 1000, 2000 ]
+
+ st,no-lsfs-fb-cap:
+ description: Disables the LS/FS feedback capacitor
+ type: boolean
+
+ st,decrease-hs-slew-rate:
+ description: Decreases the HS driver slew rate by 10%
+ type: boolean
+
+ st,tune-hs-dc-level:
+ description: |
+ Tunes the HS driver DC level
+ - <0> normal level
+ - <1> increases the level by 5 to 7 mV
+ - <2> increases the level by 10 to 14 mV
+ - <3> decreases the level by 5 to 7 mV
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 3
+ default: 0
+
+ st,enable-fs-rftime-tuning:
+ description: Enables the FS rise/fall tuning option
+ type: boolean
+
+ st,enable-hs-rftime-reduction:
+ description: Enables the HS rise/fall reduction feature
+ type: boolean
+
+ st,trim-hs-current:
+ description: |
+ Controls HS driver current trimming for choke compensation
+ - <0> = 18.87 mA target current / nominal + 0%
+ - <1> = 19.165 mA target current / nominal + 1.56%
+ - <2> = 19.46 mA target current / nominal + 3.12%
+ - <3> = 19.755 mA target current / nominal + 4.68%
+ - <4> = 20.05 mA target current / nominal + 6.24%
+ - <5> = 20.345 mA target current / nominal + 7.8%
+ - <6> = 20.64 mA target current / nominal + 9.36%
+ - <7> = 20.935 mA target current / nominal + 10.92%
+ - <8> = 21.23 mA target current / nominal + 12.48%
+ - <9> = 21.525 mA target current / nominal + 14.04%
+ - <10> = 21.82 mA target current / nominal + 15.6%
+ - <11> = 22.115 mA target current / nominal + 17.16%
+ - <12> = 22.458 mA target current / nominal + 19.01%
+ - <13> = 22.755 mA target current / nominal + 20.58%
+ - <14> = 23.052 mA target current / nominal + 22.16%
+ - <15> = 23.348 mA target current / nominal + 23.73%
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 15
+ default: 0
+
+ st,trim-hs-impedance:
+ description: |
+ Controls HS driver impedance tuning for choke compensation
+ - <0> = no impedance offset
+ - <1> = reduce the impedance by 2 ohms
+ - <2> = reduce the impedance by 4 ohms
+ - <3> = reduce the impedance by 6 ohms
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 3
+ default: 0
+
+ st,tune-squelch-level:
+ description: |
+ Tunes the squelch DC threshold value
+ - <0> = no shift in threshold
+ - <1> = threshold shift by +7 mV
+ - <2> = threshold shift by -5 mV
+ - <3> = threshold shift by +14 mV
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 3
+ default: 0
+
+ st,enable-hs-rx-gain-eq:
+ description: Enables the HS Rx gain equalizer
+ type: boolean
+
+ st,tune-hs-rx-offset:
+ description: |
+ Adjusts the HS Rx offset
+ - <0> = no offset
+ - <1> = offset of +5 mV
+ - <2> = offset of +10 mV
+ - <3> = offset of -5 mV
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 3
+ default: 0
+
+ st,no-hs-ftime-ctrl:
+ description: Disables the HS fall time control of single ended signals during pre-emphasis
+ type: boolean
+
+ st,no-lsfs-sc:
+ description: Disables the short circuit protection in LS/FS driver
+ type: boolean
+
+ st,enable-hs-tx-staggering:
+ description: Enables the basic staggering in HS Tx mode
+ type: boolean
+
+ allOf:
+ - if:
+ properties:
+ reg:
+ const: 0
+ then:
+ properties:
+ "#phy-cells":
+ const: 0
+ else:
+ properties:
+ "#phy-cells":
+ const: 1
+ description:
+ The value is used to select UTMI switch output.
+ 0 for OTG controller and 1 for Host controller.
+
+ required:
+ - reg
+ - phy-supply
+ - "#phy-cells"
+
+ additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - "#address-cells"
+ - "#size-cells"
+ - vdda1v1-supply
+ - vdda1v8-supply
+ - usb-phy@0
+ - usb-phy@1
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/stm32mp1-clks.h>
+ #include <dt-bindings/reset/stm32mp1-resets.h>
+ usbphyc: usbphyc@5a006000 {
+ compatible = "st,stm32mp1-usbphyc";
+ reg = <0x5a006000 0x1000>;
+ clocks = <&rcc USBPHY_K>;
+ resets = <&rcc USBPHY_R>;
+ vdda1v1-supply = <®11>;
+ vdda1v8-supply = <®18>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #clock-cells = <0>;
+
+ usbphyc_port0: usb-phy@0 {
+ reg = <0>;
+ phy-supply = <&vdd_usb>;
+ #phy-cells = <0>;
+ st,tune-hs-dc-level = <2>;
+ st,enable-fs-rftime-tuning;
+ st,enable-hs-rftime-reduction;
+ st,trim-hs-current = <15>;
+ st,trim-hs-impedance = <1>;
+ st,tune-squelch-level = <3>;
+ st,tune-hs-rx-offset = <2>;
+ st,no-lsfs-sc;
+ connector {
+ compatible = "usb-a-connector";
+ vbus-supply = <&vbus_sw>;
+ };
+ };
+
+ usbphyc_port1: usb-phy@1 {
+ reg = <1>;
+ phy-supply = <&vdd_usb>;
+ #phy-cells = <1>;
+ st,tune-hs-dc-level = <2>;
+ st,enable-fs-rftime-tuning;
+ st,enable-hs-rftime-reduction;
+ st,trim-hs-current = <15>;
+ st,trim-hs-impedance = <1>;
+ st,tune-squelch-level = <3>;
+ st,tune-hs-rx-offset = <2>;
+ st,no-lsfs-sc;
+ };
+ };
+...