diff --git a/Bindings/phy/phy-stm32-usbphyc.yaml b/Bindings/phy/phy-stm32-usbphyc.yaml
new file mode 100644
index 0000000..24a3dbd
--- /dev/null
+++ b/Bindings/phy/phy-stm32-usbphyc.yaml
@@ -0,0 +1,282 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/phy-stm32-usbphyc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics STM32 USB HS PHY controller
+
+description:
+
+  The STM32 USBPHYC block contains a dual port High Speed UTMI+ PHY and a UTMI
+  switch. It controls PHY configuration and status, and the UTMI+ switch that
+  selects either OTG or HOST controller for the second PHY port. It also sets
+  PLL configuration.
+
+  USBPHYC
+  |_ PLL
+  |
+  |_ PHY port#1 _________________ HOST controller
+  |                   __                 |
+  |                  / 1|________________|
+  |_ PHY port#2 ----|   |________________
+  |                  \_0|                |
+  |_ UTMI switch_______|          OTG controller
+
+maintainers:
+  - Amelie Delaunay <amelie.delaunay@foss.st.com>
+
+properties:
+  compatible:
+    const: st,stm32mp1-usbphyc
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  vdda1v1-supply:
+    description: regulator providing 1V1 power supply to the PLL block
+
+  vdda1v8-supply:
+    description: regulator providing 1V8 power supply to the PLL block
+
+  '#clock-cells':
+    description: number of clock cells for ck_usbo_48m consumer
+    const: 0
+
+# Required child nodes:
+
+patternProperties:
+  "^usb-phy@[0|1]$":
+    type: object
+    description:
+      Each port the controller provides must be represented as a sub-node.
+
+    properties:
+      reg:
+        description: phy port index.
+        maxItems: 1
+
+      phy-supply:
+        description: regulator providing 3V3 power supply to the PHY.
+
+      "#phy-cells":
+        enum: [ 0x0, 0x1 ]
+
+      connector:
+        type: object
+        $ref: /schemas/connector/usb-connector.yaml
+        unevaluatedProperties: false
+
+        properties:
+          vbus-supply: true
+
+      # It can be necessary to adjust the PHY settings to compensate parasitics, which can be due
+      # to USB connector/receptacle, routing, ESD protection component,... Here is the list of
+      # all optional parameters to tune the interface of the PHY (HS for High-Speed, FS for Full-
+      # Speed, LS for Low-Speed)
+
+      st,current-boost-microamp:
+        description: Current boosting in uA
+        enum: [ 1000, 2000 ]
+
+      st,no-lsfs-fb-cap:
+        description: Disables the LS/FS feedback capacitor
+        type: boolean
+
+      st,decrease-hs-slew-rate:
+        description: Decreases the HS driver slew rate by 10%
+        type: boolean
+
+      st,tune-hs-dc-level:
+        description: |
+          Tunes the HS driver DC level
+          - <0> normal level
+          - <1> increases the level by 5 to 7 mV
+          - <2> increases the level by 10 to 14 mV
+          - <3> decreases the level by 5 to 7 mV
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 3
+        default: 0
+
+      st,enable-fs-rftime-tuning:
+        description: Enables the FS rise/fall tuning option
+        type: boolean
+
+      st,enable-hs-rftime-reduction:
+        description: Enables the HS rise/fall reduction feature
+        type: boolean
+
+      st,trim-hs-current:
+        description: |
+          Controls HS driver current trimming for choke compensation
+          - <0> = 18.87 mA target current / nominal + 0%
+          - <1> = 19.165 mA target current / nominal + 1.56%
+          - <2> = 19.46 mA target current / nominal + 3.12%
+          - <3> = 19.755 mA target current / nominal + 4.68%
+          - <4> = 20.05 mA target current / nominal + 6.24%
+          - <5> = 20.345 mA target current / nominal + 7.8%
+          - <6> = 20.64 mA target current / nominal + 9.36%
+          - <7> = 20.935 mA target current / nominal + 10.92%
+          - <8> = 21.23 mA target current / nominal + 12.48%
+          - <9> = 21.525 mA target current / nominal + 14.04%
+          - <10> = 21.82 mA target current / nominal + 15.6%
+          - <11> = 22.115 mA target current / nominal + 17.16%
+          - <12> = 22.458 mA target current / nominal + 19.01%
+          - <13> = 22.755 mA target current / nominal + 20.58%
+          - <14> = 23.052 mA target current / nominal + 22.16%
+          - <15> = 23.348 mA target current / nominal + 23.73%
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 15
+        default: 0
+
+      st,trim-hs-impedance:
+        description: |
+          Controls HS driver impedance tuning for choke compensation
+          - <0> = no impedance offset
+          - <1> = reduce the impedance by 2 ohms
+          - <2> = reduce the impedance by 4 ohms
+          - <3> = reduce the impedance by 6 ohms
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 3
+        default: 0
+
+      st,tune-squelch-level:
+        description: |
+          Tunes the squelch DC threshold value
+          - <0> = no shift in threshold
+          - <1> = threshold shift by +7 mV
+          - <2> = threshold shift by -5 mV
+          - <3> = threshold shift by +14 mV
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 3
+        default: 0
+
+      st,enable-hs-rx-gain-eq:
+        description: Enables the HS Rx gain equalizer
+        type: boolean
+
+      st,tune-hs-rx-offset:
+        description: |
+          Adjusts the HS Rx offset
+          - <0> = no offset
+          - <1> = offset of +5 mV
+          - <2> = offset of +10 mV
+          - <3> = offset of -5 mV
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 3
+        default: 0
+
+      st,no-hs-ftime-ctrl:
+        description: Disables the HS fall time control of single ended signals during pre-emphasis
+        type: boolean
+
+      st,no-lsfs-sc:
+        description: Disables the short circuit protection in LS/FS driver
+        type: boolean
+
+      st,enable-hs-tx-staggering:
+        description: Enables the basic staggering in HS Tx mode
+        type: boolean
+
+    allOf:
+      - if:
+          properties:
+            reg:
+              const: 0
+        then:
+          properties:
+            "#phy-cells":
+              const: 0
+        else:
+          properties:
+            "#phy-cells":
+              const: 1
+              description:
+                The value is used to select UTMI switch output.
+                0 for OTG controller and 1 for Host controller.
+
+    required:
+      - reg
+      - phy-supply
+      - "#phy-cells"
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - "#address-cells"
+  - "#size-cells"
+  - vdda1v1-supply
+  - vdda1v8-supply
+  - usb-phy@0
+  - usb-phy@1
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/stm32mp1-clks.h>
+    #include <dt-bindings/reset/stm32mp1-resets.h>
+    usbphyc: usbphyc@5a006000 {
+        compatible = "st,stm32mp1-usbphyc";
+        reg = <0x5a006000 0x1000>;
+        clocks = <&rcc USBPHY_K>;
+        resets = <&rcc USBPHY_R>;
+        vdda1v1-supply = <&reg11>;
+        vdda1v8-supply = <&reg18>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+        #clock-cells = <0>;
+
+        usbphyc_port0: usb-phy@0 {
+            reg = <0>;
+            phy-supply = <&vdd_usb>;
+            #phy-cells = <0>;
+            st,tune-hs-dc-level = <2>;
+            st,enable-fs-rftime-tuning;
+            st,enable-hs-rftime-reduction;
+            st,trim-hs-current = <15>;
+            st,trim-hs-impedance = <1>;
+            st,tune-squelch-level = <3>;
+            st,tune-hs-rx-offset = <2>;
+            st,no-lsfs-sc;
+            connector {
+                compatible = "usb-a-connector";
+                vbus-supply = <&vbus_sw>;
+            };
+        };
+
+        usbphyc_port1: usb-phy@1 {
+            reg = <1>;
+            phy-supply = <&vdd_usb>;
+            #phy-cells = <1>;
+            st,tune-hs-dc-level = <2>;
+            st,enable-fs-rftime-tuning;
+            st,enable-hs-rftime-reduction;
+            st,trim-hs-current = <15>;
+            st,trim-hs-impedance = <1>;
+            st,tune-squelch-level = <3>;
+            st,tune-hs-rx-offset = <2>;
+            st,no-lsfs-sc;
+        };
+    };
+...