Squashed 'dts/upstream/' content from commit aaba2d45dc2a
git-subtree-dir: dts/upstream
git-subtree-split: aaba2d45dc2a1b3bbb710f2a3808ee1c9f340abe
diff --git a/Bindings/interrupt-controller/brcm,bcm7120-l2-intc.yaml b/Bindings/interrupt-controller/brcm,bcm7120-l2-intc.yaml
new file mode 100644
index 0000000..786f242
--- /dev/null
+++ b/Bindings/interrupt-controller/brcm,bcm7120-l2-intc.yaml
@@ -0,0 +1,152 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/interrupt-controller/brcm,bcm7120-l2-intc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom BCM7120-style Level 2 and Broadcom BCM3380 Level 1 / Level 2
+
+maintainers:
+ - Florian Fainelli <f.fainelli@gmail.com>
+
+description: >
+ This interrupt controller hardware is a second level interrupt controller that
+ is hooked to a parent interrupt controller: e.g: ARM GIC for ARM-based
+ platforms. It can be found on BCM7xxx products starting with BCM7120.
+
+ Such an interrupt controller has the following hardware design:
+
+ - outputs multiple interrupts signals towards its interrupt controller parent
+
+ - controls how some of the interrupts will be flowing, whether they will
+ directly output an interrupt signal towards the interrupt controller parent,
+ or if they will output an interrupt signal at this 2nd level interrupt
+ controller, in particular for UARTs
+
+ - has one 32-bit enable word and one 32-bit status word
+
+ - no atomic set/clear operations
+
+ - not all bits within the interrupt controller actually map to an interrupt
+
+ The typical hardware layout for this controller is represented below:
+
+ 2nd level interrupt line Outputs for the parent controller (e.g: ARM GIC)
+
+ 0 -----[ MUX ] ------------|==========> GIC interrupt 75
+ \-----------\
+ |
+ 1 -----[ MUX ] --------)---|==========> GIC interrupt 76
+ \------------|
+ |
+ 2 -----[ MUX ] --------)---|==========> GIC interrupt 77
+ \------------|
+ |
+ 3 ---------------------|
+ 4 ---------------------|
+ 5 ---------------------|
+ 7 ---------------------|---|===========> GIC interrupt 66
+ 9 ---------------------|
+ 10 --------------------|
+ 11 --------------------/
+
+ 6 ------------------------\
+ |===========> GIC interrupt 64
+ 8 ------------------------/
+
+ 12 ........................ X
+ 13 ........................ X (not connected)
+ ..
+ 31 ........................ X
+
+ The BCM3380 Level 1 / Level 2 interrupt controller shows up in various forms
+ on many BCM338x/BCM63xx chipsets. It has the following properties:
+
+ - outputs a single interrupt signal to its interrupt controller parent
+
+ - contains one or more enable/status word pairs, which often appear at
+ different offsets in different blocks
+
+ - no atomic set/clear operations
+
+allOf:
+ - $ref: /schemas/interrupt-controller.yaml#
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - brcm,bcm7120-l2-intc
+ - brcm,bcm3380-l2-intc
+
+ reg:
+ minItems: 1
+ maxItems: 4
+ description: >
+ Specifies the base physical address and size of the registers
+
+ interrupt-controller: true
+
+ "#interrupt-cells":
+ const: 1
+
+ interrupts:
+ minItems: 1
+ maxItems: 32
+
+ brcm,int-map-mask:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ description: >
+ 32-bits bit mask describing how many and which interrupts are wired to
+ this 2nd level interrupt controller, and how they match their respective
+ interrupt parents. Should match exactly the number of interrupts
+ specified in the 'interrupts' property.
+
+ brcm,irq-can-wake:
+ type: boolean
+ description: >
+ If present, this means the L2 controller can be used as a wakeup source
+ for system suspend/resume.
+
+ brcm,int-fwd-mask:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ maxItems: 1
+ description: >
+ if present, a bit mask to configure the interrupts which have a mux gate,
+ typically UARTs. Setting these bits will make their respective interrupt
+ outputs bypass this 2nd level interrupt controller completely; it is
+ completely transparent for the interrupt controller parent. This should
+ have one 32-bit word per enable/status pair.
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - interrupt-controller
+ - "#interrupt-cells"
+ - interrupts
+
+examples:
+ - |
+ irq0_intc: interrupt-controller@f0406800 {
+ compatible = "brcm,bcm7120-l2-intc";
+ interrupt-parent = <&intc>;
+ #interrupt-cells = <1>;
+ reg = <0xf0406800 0x8>;
+ interrupt-controller;
+ interrupts = <0x0 0x42 0x0>, <0x0 0x40 0x0>;
+ brcm,int-map-mask = <0xeb8>, <0x140>;
+ brcm,int-fwd-mask = <0x7>;
+ };
+
+ - |
+ irq1_intc: interrupt-controller@10000020 {
+ compatible = "brcm,bcm3380-l2-intc";
+ reg = <0x10000024 0x4>, <0x1000002c 0x4>,
+ <0x10000020 0x4>, <0x10000028 0x4>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&cpu_intc>;
+ interrupts = <2>;
+ };