Squashed 'dts/upstream/' content from commit aaba2d45dc2a
git-subtree-dir: dts/upstream
git-subtree-split: aaba2d45dc2a1b3bbb710f2a3808ee1c9f340abe
diff --git a/Bindings/display/bridge/adi,adv7511.yaml b/Bindings/display/bridge/adi,adv7511.yaml
new file mode 100644
index 0000000..5bbe818
--- /dev/null
+++ b/Bindings/display/bridge/adi,adv7511.yaml
@@ -0,0 +1,237 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/adi,adv7511.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices ADV7511/11W/13 HDMI Encoders
+
+maintainers:
+ - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+
+description: |
+ The ADV7511, ADV7511W and ADV7513 are HDMI audio and video
+ transmitters compatible with HDMI 1.4 and DVI 1.0. They support color
+ space conversion, S/PDIF, CEC and HDCP. The transmitter input is
+ parallel RGB or YUV data.
+
+properties:
+ compatible:
+ enum:
+ - adi,adv7511
+ - adi,adv7511w
+ - adi,adv7513
+
+ reg:
+ description: |
+ I2C slave addresses.
+
+ The ADV7511/11W/13 internal registers are split into four pages
+ exposed through different I2C addresses, creating four register
+ maps. Each map has it own I2C address and acts as a standard slave
+ device on the I2C bus. The main address is mandatory, others are
+ optional and revert to defaults if not specified.
+ minItems: 1
+ maxItems: 4
+
+ reg-names:
+ description:
+ Names of maps with programmable addresses. It can contain any map
+ needing a non-default address.
+ minItems: 1
+ items:
+ - const: main
+ - const: edid
+ - const: cec
+ - const: packet
+
+ clocks:
+ description: Reference to the CEC clock.
+ maxItems: 1
+
+ clock-names:
+ const: cec
+
+ interrupts:
+ maxItems: 1
+
+ pd-gpios:
+ description: GPIO connected to the power down signal.
+ maxItems: 1
+
+ avdd-supply:
+ description: A 1.8V supply that powers up the AVDD pin.
+
+ dvdd-supply:
+ description: A 1.8V supply that powers up the DVDD pin.
+
+ pvdd-supply:
+ description: A 1.8V supply that powers up the PVDD pin.
+
+ dvdd-3v-supply:
+ description: A 3.3V supply that powers up the DVDD_3V pin.
+
+ bgvdd-supply:
+ description: A 1.8V supply that powers up the BGVDD pin.
+
+ adi,input-depth:
+ description: Number of bits per color component at the input.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [ 8, 10, 12 ]
+
+ adi,input-colorspace:
+ description: Input color space.
+ enum: [ rgb, yuv422, yuv444 ]
+
+ adi,input-clock:
+ description: |
+ Input clock type.
+ "1x": one clock cycle per pixel
+ "2x": two clock cycles per pixel
+ "dd": one clock cycle per pixel, data driven on both edges
+ enum: [ 1x, 2x, dd ]
+
+ adi,clock-delay:
+ description:
+ Video data clock delay relative to the pixel clock, in ps
+ (-1200ps .. 1600 ps).
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 0
+
+ adi,embedded-sync:
+ description:
+ If defined, the input uses synchronization signals embedded in the
+ data stream (similar to BT.656).
+ type: boolean
+
+ adi,input-style:
+ description:
+ Input components arrangement variant as listed in the input
+ format tables in the datasheet.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [ 1, 2, 3 ]
+
+ adi,input-justification:
+ description: Input bit justification.
+ enum: [ left, evenly, right ]
+
+ ports:
+ description:
+ The ADV7511(W)/13 has two video ports and one audio port.
+ $ref: /schemas/graph.yaml#/properties/ports
+
+ properties:
+ port@0:
+ description: Video port for the RGB or YUV input.
+ $ref: /schemas/graph.yaml#/properties/port
+
+ port@1:
+ description: Video port for the HDMI output.
+ $ref: /schemas/graph.yaml#/properties/port
+
+ port@2:
+ description: Audio port for the HDMI output.
+ $ref: /schemas/graph.yaml#/properties/port
+
+# adi,input-colorspace and adi,input-clock are required except in
+# "rgb 1x" and "yuv444 1x" modes, in which case they must not be
+# specified.
+if:
+ not:
+ properties:
+ adi,input-colorspace:
+ contains:
+ enum: [ rgb, yuv444 ]
+ adi,input-clock:
+ contains:
+ const: 1x
+
+then:
+ required:
+ - adi,input-style
+ - adi,input-justification
+
+else:
+ properties:
+ adi,input-style: false
+ adi,input-justification: false
+
+
+required:
+ - compatible
+ - reg
+ - ports
+ - adi,input-depth
+ - adi,input-colorspace
+ - adi,input-clock
+ - avdd-supply
+ - dvdd-supply
+ - pvdd-supply
+ - dvdd-3v-supply
+ - bgvdd-supply
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ i2c@e6500000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg = <0 0xe6500000>;
+
+ adv7511w: hdmi@39 {
+ compatible = "adi,adv7511w";
+ /*
+ * The EDID page will be accessible on address 0x66 on the I2C
+ * bus. All other maps continue to use their default addresses.
+ */
+ reg = <0x39>, <0x66>;
+ reg-names = "main", "edid";
+ interrupt-parent = <&gpio3>;
+ interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
+ clocks = <&cec_clock>;
+ clock-names = "cec";
+ avdd-supply = <&v1v8>;
+ dvdd-supply = <&v1v8>;
+ pvdd-supply = <&v1v8>;
+ dvdd-3v-supply = <&v3v3>;
+ bgvdd-supply = <&v1v8>;
+
+ adi,input-depth = <8>;
+ adi,input-colorspace = "yuv422";
+ adi,input-clock = "1x";
+
+ adi,input-style = <3>;
+ adi,input-justification = "right";
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ adv7511w_in: endpoint {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ adv7511_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ codec_endpoint: endpoint {
+ remote-endpoint = <&i2s0_cpu_endpoint>;
+ };
+ };
+ };
+ };
+ };
+
+...