| /* |
| * Copyright 2008 Freescale Semiconductor, Inc. |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| /* |
| * mpc8536ds board configuration file |
| * |
| */ |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* High Level Configuration Options */ |
| #define CONFIG_BOOKE 1 /* BOOKE */ |
| #define CONFIG_E500 1 /* BOOKE e500 family */ |
| #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */ |
| #define CONFIG_MPC8536 1 |
| #define CONFIG_MPC8536DS 1 |
| |
| #define CONFIG_PCI 1 /* Enable PCI/PCIE */ |
| #define CONFIG_PCI1 1 /* Enable PCI controller 1 */ |
| #define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */ |
| #define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */ |
| #define CONFIG_PCIE3 1 /* PCIE controler 3 (ULI bridge) */ |
| #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ |
| #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ |
| |
| #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ |
| |
| #define CONFIG_TSEC_ENET /* tsec ethernet support */ |
| #define CONFIG_ENV_OVERWRITE |
| |
| /* |
| * When initializing flash, if we cannot find the manufacturer ID, |
| * assume this is the AMD flash associated with the CDS board. |
| * This allows booting from a promjet. |
| */ |
| #define CONFIG_ASSUME_AMD_FLASH |
| |
| #ifndef __ASSEMBLY__ |
| extern unsigned long get_board_sys_clk(unsigned long dummy); |
| extern unsigned long get_board_ddr_clk(unsigned long dummy); |
| #endif |
| #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ |
| #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) |
| #define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */ |
| #define CONFIG_GET_CLK_FROM_ICS307 /* decode sysclk and ddrclk freq |
| from ICS307 instead of switches */ |
| |
| /* |
| * These can be toggled for performance analysis, otherwise use default. |
| */ |
| #define CONFIG_L2_CACHE /* toggle L2 cache */ |
| #define CONFIG_BTB /* toggle branch predition */ |
| #define CONFIG_ADDR_STREAMING /* toggle addr streaming */ |
| |
| #define CONFIG_ENABLE_36BIT_PHYS 1 |
| |
| #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x7fffffff |
| #define CONFIG_PANIC_HANG /* do not reset board on panic */ |
| |
| /* |
| * Base addresses -- Note these are effective addresses where the |
| * actual resources get mapped (not physical addresses) |
| */ |
| #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ |
| #define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ |
| #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ |
| #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ |
| |
| #define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) |
| #define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) |
| #define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR+0x9000) |
| #define CONFIG_SYS_PCIE3_ADDR (CONFIG_SYS_CCSRBAR+0xb000) |
| |
| /* DDR Setup */ |
| #define CONFIG_FSL_DDR2 |
| #undef CONFIG_FSL_DDR_INTERACTIVE |
| #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ |
| #define CONFIG_DDR_SPD |
| #undef CONFIG_DDR_DLL |
| |
| #undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ |
| #define CONFIG_MEM_INIT_VALUE 0xDeadBeef |
| |
| #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE |
| |
| #define CONFIG_NUM_DDR_CONTROLLERS 1 |
| #define CONFIG_DIMM_SLOTS_PER_CTLR 1 |
| #define CONFIG_CHIP_SELECTS_PER_CTRL 2 |
| |
| /* I2C addresses of SPD EEPROMs */ |
| #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ |
| #define CONFIG_SYS_SPD_BUS_NUM 1 |
| |
| /* These are used when DDR doesn't use SPD. */ |
| #define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is 256MB */ |
| #define CONFIG_SYS_DDR_CS0_BNDS 0x0000001F |
| #define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */ |
| #define CONFIG_SYS_DDR_TIMING_3 0x00000000 |
| #define CONFIG_SYS_DDR_TIMING_0 0x00260802 |
| #define CONFIG_SYS_DDR_TIMING_1 0x3935d322 |
| #define CONFIG_SYS_DDR_TIMING_2 0x14904cc8 |
| #define CONFIG_SYS_DDR_MODE_1 0x00480432 |
| #define CONFIG_SYS_DDR_MODE_2 0x00000000 |
| #define CONFIG_SYS_DDR_INTERVAL 0x06180100 |
| #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef |
| #define CONFIG_SYS_DDR_CLK_CTRL 0x03800000 |
| #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 |
| #define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 |
| #define CONFIG_SYS_DDR_CONTROL 0xC3008000 /* Type = DDR2 */ |
| #define CONFIG_SYS_DDR_CONTROL2 0x04400010 |
| |
| #define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d |
| #define CONFIG_SYS_DDR_ERR_DIS 0x00000000 |
| #define CONFIG_SYS_DDR_SBE 0x00010000 |
| |
| /* FIXME: Not used in fixed_sdram function */ |
| #define CONFIG_SYS_DDR_MODE 0x00000022 |
| #define CONFIG_SYS_DDR_CS1_BNDS 0x00000000 |
| #define CONFIG_SYS_DDR_CS2_BNDS 0x00000FFF /* Not done */ |
| #define CONFIG_SYS_DDR_CS3_BNDS 0x00000FFF /* Not done */ |
| #define CONFIG_SYS_DDR_CS4_BNDS 0x00000FFF /* Not done */ |
| #define CONFIG_SYS_DDR_CS5_BNDS 0x00000FFF /* Not done */ |
| |
| /* Make sure required options are set */ |
| #ifndef CONFIG_SPD_EEPROM |
| #error ("CONFIG_SPD_EEPROM is required") |
| #endif |
| |
| #undef CONFIG_CLOCKS_IN_MHZ |
| |
| |
| /* |
| * Memory map -- xxx -this is wrong, needs updating |
| * |
| * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable |
| * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable |
| * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable |
| * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable |
| * |
| * Localbus cacheable (TBD) |
| * 0xXXXX_XXXX 0xXXXX_XXXX SRAM YZ M Cacheable |
| * |
| * Localbus non-cacheable |
| * 0xe000_0000 0xe80f_ffff Promjet/free 128M non-cacheable |
| * 0xe800_0000 0xefff_ffff FLASH 128M non-cacheable |
| * 0xffdf_0000 0xffdf_7fff PIXIS 32K non-cacheable TLB0 |
| * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0 |
| * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable |
| */ |
| |
| /* |
| * Local Bus Definitions |
| */ |
| #define CONFIG_SYS_FLASH_BASE 0xe0000000 /* start of FLASH 128M */ |
| |
| #define CONFIG_SYS_BR0_PRELIM 0xe8001001 |
| #define CONFIG_SYS_OR0_PRELIM 0xf8000ff7 |
| |
| #define CONFIG_SYS_BR1_PRELIM 0xe0001001 |
| #define CONFIG_SYS_OR1_PRELIM 0xf8000ff7 |
| |
| #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE + 0x8000000, CONFIG_SYS_FLASH_BASE} |
| #define CONFIG_SYS_FLASH_QUIET_TEST |
| #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ |
| #undef CONFIG_SYS_FLASH_CHECKSUM |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| |
| #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ |
| |
| #define CONFIG_FLASH_CFI_DRIVER |
| #define CONFIG_SYS_FLASH_CFI |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| #define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 |
| |
| #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ |
| |
| #define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ |
| #define PIXIS_BASE 0xffdf0000 /* PIXIS registers */ |
| |
| #define CONFIG_SYS_BR3_PRELIM (PIXIS_BASE | 0x0801) /* port size 8bit */ |
| #define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */ |
| |
| #define PIXIS_ID 0x0 /* Board ID at offset 0 */ |
| #define PIXIS_VER 0x1 /* Board version at offset 1 */ |
| #define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ |
| #define PIXIS_CSR 0x3 /* PIXIS General control/status register */ |
| #define PIXIS_RST 0x4 /* PIXIS Reset Control register */ |
| #define PIXIS_PWR 0x5 /* PIXIS Power status register */ |
| #define PIXIS_AUX 0x6 /* Auxiliary 1 register */ |
| #define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ |
| #define PIXIS_AUX2 0x8 /* Auxiliary 2 register */ |
| #define PIXIS_VCTL 0x10 /* VELA Control Register */ |
| #define PIXIS_VSTAT 0x11 /* VELA Status Register */ |
| #define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ |
| #define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ |
| #define PIXIS_VCORE0 0x14 /* VELA VCORE0 Register */ |
| #define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ |
| #define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ |
| #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ |
| #define PIXIS_VSPEED2 0x19 /* VELA VSpeed 2 */ |
| #define PIXIS_VSYSCLK0 0x1A /* VELA SYSCLK0 Register */ |
| #define PIXIS_VSYSCLK1 0x1B /* VELA SYSCLK1 Register */ |
| #define PIXIS_VSYSCLK2 0x1C /* VELA SYSCLK2 Register */ |
| #define PIXIS_VDDRCLK0 0x1D /* VELA DDRCLK0 Register */ |
| #define PIXIS_VDDRCLK1 0x1E /* VELA DDRCLK1 Register */ |
| #define PIXIS_VDDRCLK2 0x1F /* VELA DDRCLK2 Register */ |
| #define PIXIS_VWATCH 0x24 /* Watchdog Register */ |
| #define PIXIS_LED 0x25 /* LED Register */ |
| |
| /* old pixis referenced names */ |
| #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ |
| #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ |
| #define CONFIG_SYS_PIXIS_VBOOT_MASK 0xc0 |
| |
| /* define to use L1 as initial stack */ |
| #define CONFIG_L1_INIT_RAM |
| #define CONFIG_SYS_INIT_RAM_LOCK 1 |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ |
| #define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */ |
| |
| #define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ |
| #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ |
| |
| /* Serial Port - controlled on board with jumper J8 |
| * open - index 2 |
| * shorted - index 1 |
| */ |
| #define CONFIG_CONS_INDEX 1 |
| #undef CONFIG_SERIAL_SOFTWARE_FIFO |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) |
| |
| /* Use the HUSH parser */ |
| #define CONFIG_SYS_HUSH_PARSER |
| #ifdef CONFIG_SYS_HUSH_PARSER |
| #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " |
| #endif |
| |
| /* |
| * Pass open firmware flat tree |
| */ |
| #define CONFIG_OF_LIBFDT 1 |
| #define CONFIG_OF_BOARD_SETUP 1 |
| #define CONFIG_OF_STDOUT_VIA_ALIAS 1 |
| |
| #define CONFIG_SYS_64BIT_STRTOUL 1 |
| #define CONFIG_SYS_64BIT_VSPRINTF 1 |
| |
| |
| /* |
| * I2C |
| */ |
| #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ |
| #define CONFIG_HARD_I2C /* I2C with hardware support */ |
| #undef CONFIG_SOFT_I2C /* I2C bit-banged */ |
| #define CONFIG_I2C_MULTI_BUS |
| #define CONFIG_I2C_CMD_TREE |
| #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ |
| #define CONFIG_SYS_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_I2C_NOPROBES {{0, 0x29}} /* Don't probe these addrs */ |
| #define CONFIG_SYS_I2C_OFFSET 0x3000 |
| #define CONFIG_SYS_I2C2_OFFSET 0x3100 |
| |
| /* |
| * I2C2 EEPROM |
| */ |
| #define CONFIG_ID_EEPROM |
| #ifdef CONFIG_ID_EEPROM |
| #define CONFIG_SYS_I2C_EEPROM_NXID |
| #endif |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 |
| #define CONFIG_SYS_EEPROM_BUS_NUM 1 |
| |
| /* |
| * General PCI |
| * Memory space is mapped 1-1, but I/O space must start from 0. |
| */ |
| |
| /* PCI view of System Memory */ |
| #define CONFIG_SYS_PCI_MEMORY_BUS 0x00000000 |
| #define CONFIG_SYS_PCI_MEMORY_PHYS 0x00000000 |
| #define CONFIG_SYS_PCI_MEMORY_SIZE 0x80000000 |
| |
| #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 |
| #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE |
| #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ |
| #define CONFIG_SYS_PCI1_IO_BASE 0x00000000 |
| #define CONFIG_SYS_PCI1_IO_PHYS 0xffc00000 |
| #define CONFIG_SYS_PCI1_IO_SIZE 0x00010000 /* 64k */ |
| |
| /* controller 1, Slot 1, tgtid 1, Base address a000 */ |
| #define CONFIG_SYS_PCIE1_MEM_BASE 0x90000000 |
| #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE |
| #define CONFIG_SYS_PCIE1_MEM_SIZE 0x08000000 /* 128M */ |
| #define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 |
| #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc10000 |
| #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ |
| |
| /* controller 2, Slot 2, tgtid 2, Base address 9000 */ |
| #define CONFIG_SYS_PCIE2_MEM_BASE 0x98000000 |
| #define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BASE |
| #define CONFIG_SYS_PCIE2_MEM_SIZE 0x08000000 /* 128M */ |
| #define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 |
| #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc20000 |
| #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ |
| |
| /* controller 3, direct to uli, tgtid 3, Base address 8000 */ |
| #define CONFIG_SYS_PCIE3_MEM_BASE 0xa0000000 |
| #define CONFIG_SYS_PCIE3_MEM_PHYS CONFIG_SYS_PCIE3_MEM_BASE |
| #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ |
| #define CONFIG_SYS_PCIE3_IO_BASE 0x00000000 |
| #define CONFIG_SYS_PCIE3_IO_PHYS 0xffc30000 |
| #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ |
| |
| #if defined(CONFIG_PCI) |
| |
| #define CONFIG_NET_MULTI |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| |
| /*PCIE video card used*/ |
| #define VIDEO_IO_OFFSET CONFIG_SYS_PCIE3_IO_PHYS |
| |
| /*PCI video card used*/ |
| /*#define VIDEO_IO_OFFSET CONFIG_SYS_PCI1_IO_PHYS*/ |
| |
| /* video */ |
| #define CONFIG_VIDEO |
| |
| #if defined(CONFIG_VIDEO) |
| #define CONFIG_BIOSEMU |
| #define CONFIG_CFB_CONSOLE |
| #define CONFIG_VIDEO_SW_CURSOR |
| #define CONFIG_VGA_AS_SINGLE_DEVICE |
| #define CONFIG_ATI_RADEON_FB |
| #define CONFIG_VIDEO_LOGO |
| /*#define CONFIG_CONSOLE_CURSOR*/ |
| #define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCIE3_IO_PHYS |
| #endif |
| |
| #undef CONFIG_EEPRO100 |
| #undef CONFIG_TULIP |
| #undef CONFIG_RTL8139 |
| |
| #ifdef CONFIG_RTL8139 |
| /* This macro is used by RTL8139 but not defined in PPC architecture */ |
| #define KSEG1ADDR(x) ({u32 _x=le32_to_cpu(*(u32 *)(x)); (&_x);}) |
| #define _IO_BASE 0x00000000 |
| #endif |
| |
| #ifndef CONFIG_PCI_PNP |
| #define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BASE |
| #define PCI_ENET0_MEMADDR CONFIG_SYS_PCI1_IO_BASE |
| #define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */ |
| #endif |
| |
| #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| |
| #endif /* CONFIG_PCI */ |
| |
| /* SATA */ |
| #define CONFIG_LIBATA |
| #define CONFIG_FSL_SATA |
| |
| #define CONFIG_SYS_SATA_MAX_DEVICE 2 |
| #define CONFIG_SATA1 |
| #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR |
| #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA |
| #define CONFIG_SATA2 |
| #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR |
| #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA |
| |
| #ifdef CONFIG_FSL_SATA |
| #define CONFIG_LBA48 |
| #define CONFIG_CMD_SATA |
| #define CONFIG_DOS_PARTITION |
| #define CONFIG_CMD_EXT2 |
| #endif |
| |
| #if defined(CONFIG_TSEC_ENET) |
| |
| #ifndef CONFIG_NET_MULTI |
| #define CONFIG_NET_MULTI 1 |
| #endif |
| |
| #define CONFIG_MII 1 /* MII PHY management */ |
| #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ |
| #define CONFIG_TSEC1 1 |
| #define CONFIG_TSEC1_NAME "eTSEC1" |
| #define CONFIG_TSEC3 1 |
| #define CONFIG_TSEC3_NAME "eTSEC3" |
| |
| #define CONFIG_FSL_SGMII_RISER 1 |
| #define SGMII_RISER_PHY_OFFSET 0x1c |
| |
| #define TSEC1_PHY_ADDR 1 /* TSEC1 -> PHY1 */ |
| #define TSEC3_PHY_ADDR 0 /* TSEC3 -> PHY0 */ |
| |
| #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| |
| #define TSEC1_PHYIDX 0 |
| #define TSEC3_PHYIDX 0 |
| |
| #define CONFIG_ETHPRIME "eTSEC1" |
| |
| #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ |
| |
| #endif /* CONFIG_TSEC_ENET */ |
| |
| /* |
| * Environment |
| */ |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #if CONFIG_SYS_MONITOR_BASE > 0xfff80000 |
| #define CONFIG_ENV_ADDR 0xfff80000 |
| #else |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x60000) |
| #endif |
| #define CONFIG_ENV_SIZE 0x2000 |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_IRQ |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_ELF |
| #define CONFIG_CMD_IRQ |
| #define CONFIG_CMD_SETEXPR |
| |
| #if defined(CONFIG_PCI) |
| #define CONFIG_CMD_PCI |
| #define CONFIG_CMD_BEDBUG |
| #define CONFIG_CMD_NET |
| #endif |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_CMDLINE_EDITING /* Command-line editing */ |
| #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ |
| #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ |
| |
| /* |
| * Internal Definitions |
| * |
| * Boot Flags |
| */ |
| #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ |
| #define BOOTFLAG_WARM 0x02 /* Software reboot */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ |
| #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ |
| #endif |
| |
| /* |
| * Environment Configuration |
| */ |
| |
| /* The mac addresses for all ethernet interface */ |
| #if defined(CONFIG_TSEC_ENET) |
| #define CONFIG_HAS_ETH0 |
| #define CONFIG_ETHADDR 00:E0:0C:02:00:FD |
| #define CONFIG_HAS_ETH1 |
| #define CONFIG_ETH1ADDR 00:E0:0C:02:01:FD |
| #define CONFIG_HAS_ETH2 |
| #define CONFIG_ETH2ADDR 00:E0:0C:02:02:FD |
| #define CONFIG_HAS_ETH3 |
| #define CONFIG_ETH3ADDR 00:E0:0C:02:03:FD |
| #endif |
| |
| #define CONFIG_IPADDR 192.168.1.254 |
| |
| #define CONFIG_HOSTNAME unknown |
| #define CONFIG_ROOTPATH /opt/nfsroot |
| #define CONFIG_BOOTFILE uImage |
| #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ |
| |
| #define CONFIG_SERVERIP 192.168.1.1 |
| #define CONFIG_GATEWAYIP 192.168.1.1 |
| #define CONFIG_NETMASK 255.255.255.0 |
| |
| /* default location for tftp and bootm */ |
| #define CONFIG_LOADADDR 1000000 |
| |
| #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ |
| #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=eth0\0" \ |
| "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ |
| "tftpflash=tftpboot $loadaddr $uboot; " \ |
| "protect off " MK_STR(TEXT_BASE) " +$filesize; " \ |
| "erase " MK_STR(TEXT_BASE) " +$filesize; " \ |
| "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \ |
| "protect on " MK_STR(TEXT_BASE) " +$filesize; " \ |
| "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \ |
| "consoledev=ttyS0\0" \ |
| "ramdiskaddr=2000000\0" \ |
| "ramdiskfile=8536ds/ramdisk.uboot\0" \ |
| "fdtaddr=c00000\0" \ |
| "fdtfile=8536ds/mpc8536ds.dtb\0" \ |
| "bdev=sda3\0" |
| |
| #define CONFIG_HDBOOT \ |
| "setenv bootargs root=/dev/$bdev rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr - $fdtaddr" |
| |
| #define CONFIG_NFSBOOTCOMMAND \ |
| "setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=$serverip:$rootpath " \ |
| "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr - $fdtaddr" |
| |
| #define CONFIG_RAMBOOTCOMMAND \ |
| "setenv bootargs root=/dev/ram rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $ramdiskaddr $ramdiskfile;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr $ramdiskaddr $fdtaddr" |
| |
| #define CONFIG_BOOTCOMMAND CONFIG_HDBOOT |
| |
| #endif /* __CONFIG_H */ |