| /* |
| * (C) Copyright 2008 |
| * Matthias Fuchs, esd gmbh, matthias.fuchs@esd-electronics.com |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #include <asm-offsets.h> |
| #include <ppc_asm.tmpl> |
| #include <asm/mmu.h> |
| #include <config.h> |
| |
| /* |
| * TLB TABLE |
| * |
| * This table is used by the cpu boot code to setup the initial tlb |
| * entries. Rather than make broad assumptions in the cpu source tree, |
| * this table lets each board set things up however they like. |
| * |
| * Pointer to the table is returned in r1 |
| */ |
| .section .bootpg,"ax" |
| .globl tlbtab |
| |
| tlbtab: |
| tlbtab_start |
| |
| /* |
| * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the |
| * speed up boot process. It is patched after relocation to enable SA_I |
| */ |
| tlbentry( CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M, CONFIG_SYS_BOOT_BASE_ADDR, 1, AC_RWX | SA_G ) |
| |
| #ifdef CONFIG_SYS_INIT_RAM_DCACHE |
| /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ |
| tlbentry( CONFIG_SYS_INIT_RAM_ADDR, SZ_64K, CONFIG_SYS_INIT_RAM_ADDR, 0, AC_RWX | SA_G ) |
| #endif |
| |
| /* TLB-entry for PCI Memory */ |
| tlbentry( CONFIG_SYS_PCI_MEMBASE, SZ_256M, CONFIG_SYS_PCI_MEMBASE, 1, AC_RW | SA_IG ) |
| tlbentry( CONFIG_SYS_PCI_MEMBASE1, SZ_256M, CONFIG_SYS_PCI_MEMBASE1, 1, AC_RW | SA_IG ) |
| tlbentry( CONFIG_SYS_PCI_MEMBASE2, SZ_256M, CONFIG_SYS_PCI_MEMBASE2, 1, AC_RW | SA_IG ) |
| tlbentry( CONFIG_SYS_PCI_MEMBASE3, SZ_256M, CONFIG_SYS_PCI_MEMBASE3, 1, AC_RW | SA_IG ) |
| |
| /* TLB-entry for PCI IO */ |
| tlbentry( CONFIG_SYS_PCI_IOBASE, SZ_64K, CONFIG_SYS_PCI_IOBASE, 1, AC_RW | SA_IG ) |
| |
| /* TLB-entries for EBC: CPLD, DUMEM, DUIO */ |
| tlbentry( CONFIG_SYS_CPLD_BASE, SZ_1K, CONFIG_SYS_CPLD_BASE, 1, AC_RWX | SA_IG ) |
| tlbentry( CONFIG_SYS_DUMEM_BASE, SZ_1M, CONFIG_SYS_DUMEM_BASE, 1, AC_RWX | SA_IG ) |
| tlbentry( CONFIG_SYS_DUIO_BASE, SZ_64K, CONFIG_SYS_DUIO_BASE, 1, AC_RWX | SA_IG ) |
| |
| /* TLB-entry for NAND */ |
| tlbentry( CONFIG_SYS_NAND0_ADDR, SZ_1K, CONFIG_SYS_NAND0_ADDR, 1, AC_RWX | SA_IG ) |
| tlbentry( CONFIG_SYS_NAND1_ADDR, SZ_1K, CONFIG_SYS_NAND1_ADDR, 1, AC_RWX | SA_IG ) |
| |
| /* TLB-entry for Internal Registers & OCM */ |
| tlbentry( 0xe0000000, SZ_16M, 0xe0000000, 0, AC_RWX | SA_I ) |
| |
| /* TLB-entry PCI registers */ |
| tlbentry( 0xEEC00000, SZ_1K, 0xEEC00000, 1, AC_RWX | SA_IG ) |
| |
| /* TLB-entry for peripherals */ |
| tlbentry( 0xEF000000, SZ_16M, 0xEF000000, 1, AC_RWX | SA_IG) |
| |
| tlbtab_end |