include/configs/MPC8360ERDK.h - filogic/uboot - Gitiles

 /*
  * Copyright (C) 2006 Freescale Semiconductor, Inc.
  *                    Dave Liu <daveliu@freescale.com>
  *
  * Copyright (C) 2007 Logic Product Development, Inc.
  *                    Peter Barada <peterb@logicpd.com>
  *
  * Copyright (C) 2007 MontaVista Software, Inc.
  *                    Anton Vorontsov <avorontsov@ru.mvista.com>
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
  * published by the Free Software Foundation; either version 2 of
  * the License, or (at your option) any later version.
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 #undef DEBUG

 /*
  * High Level Configuration Options
  */
 #define CONFIG_E300		1 /* E300 family */
 #define CONFIG_QE		1 /* Has QE */
 #define CONFIG_MPC83XX		1 /* MPC83XX family */
 #define CONFIG_MPC8360		1 /* MPC8360 CPU specific */
 #define CONFIG_MPC8360ERDK	1 /* MPC8360ERDK board specific */

 /*
  * System Clock Setup
  */
 #ifdef CONFIG_CLKIN_33MHZ
 #define CONFIG_83XX_CLKIN		33000000
 #define CONFIG_SYS_CLK_FREQ		33000000
 #define PCI_33M				1
 #define HRCWL_CSB_TO_CLKIN_MPC8360ERDK	HRCWL_CSB_TO_CLKIN_10X1
 #else
 #define CONFIG_83XX_CLKIN		66000000
 #define CONFIG_SYS_CLK_FREQ		66000000
 #define PCI_66M				1
 #define HRCWL_CSB_TO_CLKIN_MPC8360ERDK	HRCWL_CSB_TO_CLKIN_5X1
 #endif /* CONFIG_CLKIN_33MHZ */

 /*
  * Hardware Reset Configuration Word
  */
 #define CFG_HRCW_LOW (\
 	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 	HRCWL_DDR_TO_SCB_CLK_1X1 |\
 	HRCWL_CSB_TO_CLKIN_MPC8360ERDK |\
 	HRCWL_CORE_TO_CSB_2X1 |\
 	HRCWL_CE_TO_PLL_1X15)

 #define CFG_HRCW_HIGH (\
 	HRCWH_PCI_HOST |\
 	HRCWH_PCI1_ARBITER_ENABLE |\
 	HRCWH_PCICKDRV_ENABLE |\
 	HRCWH_CORE_ENABLE |\
 	HRCWH_FROM_0X00000100 |\
 	HRCWH_BOOTSEQ_DISABLE |\
 	HRCWH_SW_WATCHDOG_DISABLE |\
 	HRCWH_ROM_LOC_LOCAL_16BIT |\
 	HRCWH_SECONDARY_DDR_DISABLE |\
 	HRCWH_BIG_ENDIAN |\
 	HRCWH_LALE_EARLY)

 /*
  * System IO Config
  */
 #define CFG_SICRH		0x00000000
 #define CFG_SICRL		0x40000000

 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
 #define CONFIG_BOARD_EARLY_INIT_R

 /*
  * IMMR new address
  */
 #define CFG_IMMR		0xE0000000

 /*
  * DDR Setup
  */
 #define CFG_DDR_BASE		0x00000000 /* DDR is system memory */
 #define CFG_SDRAM_BASE		CFG_DDR_BASE
 #define CFG_DDR_SDRAM_BASE	CFG_DDR_BASE
 #define CFG_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
 				DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)

 #define CFG_83XX_DDR_USES_CS0

 #undef CONFIG_DDR_ECC		/* support DDR ECC function */
 #undef CONFIG_DDR_ECC_CMD	/* Use DDR ECC user commands */

 /*
  * DDRCDR - DDR Control Driver Register
  */
 #define CFG_DDRCDR_VALUE	0x80080001

 #undef CONFIG_SPD_EEPROM	/* Do not use SPD EEPROM for DDR setup */

 /*
  * Manually set up DDR parameters
  */
 #define CONFIG_DDR_II
 #define CFG_DDR_SIZE		256 /* MB */
 #define CFG_DDRCDR		0x80080001
 #define CFG_DDR_CS0_BNDS	0x0000000f
 #define CFG_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | \
 				 CSCONFIG_COL_BIT_10)
 #define CFG_DDR_TIMING_0	0x00330903
 #define CFG_DDR_TIMING_1	0x3835a322
 #define CFG_DDR_TIMING_2	0x00104909
 #define CFG_DDR_TIMING_3	0x00000000
 #define CFG_DDR_CLK_CNTL	0x02000000
 #define CFG_DDR_MODE		0x47800432
 #define CFG_DDR_MODE2		0x8000c000
 #define CFG_DDR_INTERVAL	0x045b0100
 #define CFG_DDR_SDRAM_CFG	0x03000000
 #define CFG_DDR_SDRAM_CFG2	0x00001000

 /*
  * Memory test
  */
 #undef CFG_DRAM_TEST		/* memory test, takes time */
 #define CFG_MEMTEST_START	0x00000000 /* memtest region */
 #define CFG_MEMTEST_END		0x00100000

 /*
  * The reserved memory
  */
 #define CFG_MONITOR_BASE	TEXT_BASE /* start of monitor */
 #define CFG_FLASH_BASE		0xFF800000 /* FLASH base address */

 #if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
 #define CFG_RAMBOOT
 #else
 #undef	CFG_RAMBOOT
 #endif

 #define CFG_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon */
 #define CFG_MALLOC_LEN		(128 * 1024) /* Reserved for malloc */

 /*
  * Initial RAM Base Address Setup
  */
 #define CFG_INIT_RAM_LOCK	1
 #define CFG_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
 #define CFG_INIT_RAM_END	0x1000 /* End of used area in RAM */
 #define CFG_GBL_DATA_SIZE	0x100 /* num bytes initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)

 /*
  * Local Bus Configuration & Clock Setup
  */
 #define CFG_LCRR		(LCRR_DBYP | LCRR_CLKDIV_4)
 #define CFG_LBC_LBCR		0x00000000

 /*
  * FLASH on the Local Bus
  */
 #define CFG_FLASH_CFI		/* use the Common Flash Interface */
 #define CFG_FLASH_CFI_DRIVER	/* use the CFI driver */
 #define CFG_FLASH_SIZE		8 /* max FLASH size is 32M */
 #define CFG_FLASH_PROTECTION	1 /* Use intel Flash protection. */

 #define CFG_LBLAWBAR0_PRELIM	CFG_FLASH_BASE /* Window base at flash base */
 #define CFG_LBLAWAR0_PRELIM	0x80000018 /* 32MB window size */

 #define CFG_BR0_PRELIM	(CFG_FLASH_BASE | /* Flash Base address */ \
 			(2 << BR_PS_SHIFT) | /* 16 bit port size */ \
 			BR_V)	/* valid */
 #define CFG_OR0_PRELIM		((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \
 				OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | \
 				OR_GPCM_XACS | OR_GPCM_SCY_15 | \
 				OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)

 #define CFG_MAX_FLASH_BANKS	1 /* number of banks */
 #define CFG_MAX_FLASH_SECT	256 /* max sectors per device */

 #undef	CFG_FLASH_CHECKSUM

 /*
  * NAND flash on the local bus
  */
 #define CFG_NAND_BASE		0x60000000

 #define CFG_LBLAWBAR1_PRELIM	CFG_NAND_BASE
 #define CFG_LBLAWAR1_PRELIM	0x8000001b /* Access window size 4K */

 /* Port size 8 bit, UPMA */
 #define CFG_BR1_PRELIM		(CFG_NAND_BASE | 0x00000881)
 #define CFG_OR1_PRELIM		0xfc000001

 /*
  * Fujitsu MB86277 (MINT) graphics controller
  */
 #define CFG_VIDEO_BASE		0x70000000

 #define CFG_LBLAWBAR2_PRELIM	CFG_VIDEO_BASE
 #define CFG_LBLAWAR2_PRELIM	0x80000019 /* Access window size 64MB */

 /* Port size 32 bit, UPMB */
 #define CFG_BR2_PRELIM		(CFG_VIDEO_BASE | 0x000018a1) /* PS=11, UPMB */
 #define CFG_OR2_PRELIM		0xfc000001 /* (64MB, EAD=1) */

 /*
  * Serial Port
  */
 #define CONFIG_CONS_INDEX	1
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
 #define CFG_NS16550
 #define CFG_NS16550_SERIAL
 #define CFG_NS16550_REG_SIZE	1
 #define CFG_NS16550_CLK		get_bus_freq(0)

 #define CFG_BAUDRATE_TABLE  \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200,}

 #define CFG_NS16550_COM1	(CFG_IMMR+0x4500)
 #define CFG_NS16550_COM2	(CFG_IMMR+0x4600)

 #define CONFIG_CMDLINE_EDITING	1	/* add command line history */
 /* Use the HUSH parser */
 #define CFG_HUSH_PARSER
 #ifdef	CFG_HUSH_PARSER
 #define CFG_PROMPT_HUSH_PS2 "> "
 #endif

 /* Pass open firmware flat tree */
 #define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1

 /* I2C */
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
 #undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_FSL_I2C
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_I2C_CMD_TREE
 #define CFG_I2C_SPEED	400000	/* I2C speed and slave address */
 #define CFG_I2C_SLAVE	0x7F
 #define CFG_I2C_NOPROBES	{{0x52}} /* Don't probe these addrs */
 #define CFG_I2C_OFFSET	0x3000
 #define CFG_I2C2_OFFSET 0x3100

 /*
  * General PCI
  * Addresses are mapped 1-1.
  */
 #define CONFIG_PCI
 #define CONFIG_83XX_GENERIC_PCI	1

 #define CFG_PCI1_MEM_BASE	0x80000000
 #define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
 #define CFG_PCI1_MEM_SIZE	0x10000000 /* 256M */
 #define CFG_PCI1_MMIO_BASE	0x90000000
 #define CFG_PCI1_MMIO_PHYS	CFG_PCI1_MMIO_BASE
 #define CFG_PCI1_MMIO_SIZE	0x10000000 /* 256M */
 #define CFG_PCI1_IO_BASE	0xE0300000
 #define CFG_PCI1_IO_PHYS	0xE0300000
 #define CFG_PCI1_IO_SIZE	0x100000 /* 1M */

 #ifdef CONFIG_PCI

 #define CONFIG_NET_MULTI
 #define CONFIG_PCI_PNP		/* do pci plug-and-play */

 #undef CONFIG_EEPRO100
 #undef CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
 #define CFG_PCI_SUBSYS_VENDORID 0x1957	/* Freescale */

 #endif	/* CONFIG_PCI */


 #ifndef CONFIG_NET_MULTI
 #define CONFIG_NET_MULTI	1
 #endif

 /*
  * QE UEC ethernet configuration
  */
 #define CONFIG_UEC_ETH
 #define CONFIG_ETHPRIME		"Freescale GETH"

 #define CONFIG_UEC_ETH1		/* GETH1 */

 #ifdef CONFIG_UEC_ETH1
 #define CFG_UEC1_UCC_NUM	0	/* UCC1 */
 #define CFG_UEC1_RX_CLK		QE_CLK_NONE
 #define CFG_UEC1_TX_CLK		QE_CLK9
 #define CFG_UEC1_ETH_TYPE	GIGA_ETH
 #define CFG_UEC1_PHY_ADDR	2
 #define CFG_UEC1_INTERFACE_MODE ENET_1000_GMII
 #endif

 #define CONFIG_UEC_ETH2		/* GETH2 */

 #ifdef CONFIG_UEC_ETH2
 #define CFG_UEC2_UCC_NUM	1	/* UCC2 */
 #define CFG_UEC2_RX_CLK		QE_CLK_NONE
 #define CFG_UEC2_TX_CLK		QE_CLK4
 #define CFG_UEC2_ETH_TYPE	GIGA_ETH
 #define CFG_UEC2_PHY_ADDR	4
 #define CFG_UEC2_INTERFACE_MODE ENET_1000_GMII
 #endif

 /*
  * Environment
  */

 #ifndef CFG_RAMBOOT
 #define CFG_ENV_IS_IN_FLASH	1
 #define CFG_ENV_ADDR		(CFG_MONITOR_BASE + 0x40000)
 #define CFG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
 #define CFG_ENV_SIZE		0x20000
 #else /* CFG_RAMBOOT */
 #define CFG_NO_FLASH		1	/* Flash is not usable now */
 #define CFG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
 #define CFG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
 #define CFG_ENV_SIZE		0x2000
 #endif /* CFG_RAMBOOT */

 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */

 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME


 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_PING
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_ASKENV

 #if defined(CONFIG_PCI)
 #define CONFIG_CMD_PCI
 #endif

 #if defined(CFG_RAMBOOT)
 #undef CONFIG_CMD_ENV
 #undef CONFIG_CMD_LOADS
 #endif

 #undef CONFIG_WATCHDOG		/* watchdog disabled */

 /*
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP		/* undef to save memory */
 #define CFG_LOAD_ADDR		0x2000000 /* default load address */
 #define CFG_PROMPT		"=> "	/* Monitor Command Prompt */

 #if defined(CONFIG_CMD_KGDB)
 	#define CFG_CBSIZE	1024 /* Console I/O Buffer Size */
 #else
 	#define CFG_CBSIZE	256 /* Console I/O Buffer Size */
 #endif

 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args */
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
 #define CFG_HZ		1000		/* decrementer freq: 1ms ticks */

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */

 /*
  * Core HID Setup
  */
 #define CFG_HID0_INIT		0x000000000
 #define CFG_HID0_FINAL		HID0_ENABLE_MACHINE_CHECK
 #define CFG_HID2		HID2_HBE

 /*
  * Cache Config
  */
 #define CFG_DCACHE_SIZE		32768
 #define CFG_CACHELINE_SIZE	32
 #if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5 /*log base 2 of the above value */
 #endif

 /*
  * MMU Setup
  */

 /* DDR: cache cacheable */
 #define CFG_IBAT0L	(CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
 #define CFG_IBAT0U	(CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
 #define CFG_DBAT0L	CFG_IBAT0L
 #define CFG_DBAT0U	CFG_IBAT0U

 /* IMMRBAR & PCI IO: cache-inhibit and guarded */
 #define CFG_IBAT1L	(CFG_IMMR | BATL_PP_10 | \
 			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CFG_IBAT1U	(CFG_IMMR | BATU_BL_4M | BATU_VS | BATU_VP)
 #define CFG_DBAT1L	CFG_IBAT1L
 #define CFG_DBAT1U	CFG_IBAT1U

 /* NAND: cache-inhibit and guarded */
 #define CFG_IBAT2L	(CFG_NAND_BASE | BATL_PP_10 | BATL_CACHEINHIBIT |\
 			 BATL_GUARDEDSTORAGE)
 #define CFG_IBAT2U	(CFG_NAND_BASE | BATU_BL_64M | BATU_VS | BATU_VP)
 #define CFG_DBAT2L	CFG_IBAT2L
 #define CFG_DBAT2U	CFG_IBAT2U

 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
 #define CFG_IBAT3L	(CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
 #define CFG_IBAT3U	(CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
 #define CFG_DBAT3L	(CFG_FLASH_BASE | BATL_PP_10 | \
 			 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CFG_DBAT3U	CFG_IBAT3U

 /* Stack in dcache: cacheable, no memory coherence */
 #define CFG_IBAT4L	(CFG_INIT_RAM_ADDR | BATL_PP_10)
 #define CFG_IBAT4U	(CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
 #define CFG_DBAT4L	CFG_IBAT4L
 #define CFG_DBAT4U	CFG_IBAT4U

 #define CFG_IBAT5L	(CFG_VIDEO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | \
 			 BATL_GUARDEDSTORAGE)
 #define CFG_IBAT5U	(CFG_VIDEO_BASE | BATU_BL_64M | BATU_VS | BATU_VP)
 #define CFG_DBAT5L	CFG_IBAT5L
 #define CFG_DBAT5U	CFG_IBAT5U

 #ifdef CONFIG_PCI
 /* PCI MEM space: cacheable */
 #define CFG_IBAT6L	(CFG_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
 #define CFG_IBAT6U	(CFG_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
 #define CFG_DBAT6L	CFG_IBAT6L
 #define CFG_DBAT6U	CFG_IBAT6U
 /* PCI MMIO space: cache-inhibit and guarded */
 #define CFG_IBAT7L	(CFG_PCI1_MMIO_PHYS | BATL_PP_10 | \
 			 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CFG_IBAT7U	(CFG_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
 #define CFG_DBAT7L	CFG_IBAT7L
 #define CFG_DBAT7U	CFG_IBAT7U
 #else /* CONFIG_PCI */
 #define CFG_IBAT6L	(0)
 #define CFG_IBAT6U	(0)
 #define CFG_IBAT7L	(0)
 #define CFG_IBAT7U	(0)
 #define CFG_DBAT6L	CFG_IBAT6L
 #define CFG_DBAT6U	CFG_IBAT6U
 #define CFG_DBAT7L	CFG_IBAT7L
 #define CFG_DBAT7U	CFG_IBAT7U
 #endif /* CONFIG_PCI */

 /*
  * Internal Definitions
  *
  * Boot Flags
  */
 #define BOOTFLAG_COLD	0x01 /* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02 /* Software reboot */

 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif

 /*
  * Environment Configuration
  */
 #define CONFIG_ENV_OVERWRITE

 #if defined(CONFIG_UEC_ETH)
 #define CONFIG_HAS_ETH0
 #define CONFIG_HAS_ETH1
 #define CONFIG_HAS_ETH2
 #define CONFIG_HAS_ETH3
 #define CONFIG_ETHADDR	00:04:9f:ef:01:01
 #define CONFIG_ETH1ADDR	00:04:9f:ef:01:02
 #define CONFIG_ETH2ADDR	00:04:9f:ef:01:03
 #define CONFIG_ETH3ADDR	00:04:9f:ef:01:04
 #endif

 #define CONFIG_BAUDRATE 115200

 #define CONFIG_LOADADDR	a00000
 #define CONFIG_HOSTNAME	mpc8360erdk
 #define CONFIG_BOOTFILE	uImage

 #define CONFIG_IPADDR		10.0.0.99
 #define CONFIG_SERVERIP		10.0.0.2
 #define CONFIG_GATEWAYIP	10.0.0.2
 #define CONFIG_NETMASK		255.255.255.0
 #define CONFIG_ROOTPATH		/nfsroot/

 #define	CONFIG_BOOTDELAY 2	/* -1 disables auto-boot */
 #undef	CONFIG_BOOTARGS		/* the boot command will set bootargs */

 #define CONFIG_EXTRA_ENV_SETTINGS \
    "netdev=eth0\0"\
    "consoledev=ttyS0\0"\
    "loadaddr=a00000\0"\
    "fdtaddr=900000\0"\
    "bootfile=uImage\0"\
    "fdtfile=dtb\0"\
    "fsfile=fs\0"\
    "ubootfile=u-boot.bin\0"\
    "setbootargs=setenv bootargs console=$consoledev,$baudrate "\
    		"$mtdparts panic=1\0"\
    "adddhcpargs=setenv bootargs $bootargs ip=on\0"\
    "addnfsargs=setenv bootargs $bootargs ip=$ipaddr:$serverip:"\
    		"$gatewayip:$netmask:$hostname:$netdev:off "\
    		"root=/dev/nfs rw nfsroot=$serverip:$rootpath\0"\
    "tftp_get_uboot=tftp 100000 $ubootfile\0"\
    "tftp_get_kernel=tftp $loadaddr $bootfile\0"\
    "tftp_get_dtb=tftp $fdtaddr $fdtfile\0"\
    "tftp_get_fs=tftp c00000 $fsfile\0"\
    "nor_reflash=protect off ff800000 ff87ffff ; erase ff800000 ff87ffff ; "\
    		"cp.b 100000 ff800000 $filesize\0"\
    "boot_m=bootm $loadaddr - $fdtaddr\0"\
    "dhcpboot=run setbootargs adddhcpargs tftp_get_kernel tftp_get_dtb "\
    		"boot_m\0"\
    "nfsboot=run setbootargs addnfsargs tftp_get_kernel tftp_get_dtb "\
    		"boot_m\0"\
    ""

 #define CONFIG_BOOTCOMMAND "run dhcpboot"

 #endif /* __CONFIG_H */
	/*
	* Copyright (C) 2006 Freescale Semiconductor, Inc.
	* Dave Liu <daveliu@freescale.com>
	*
	* Copyright (C) 2007 Logic Product Development, Inc.
	* Peter Barada <peterb@logicpd.com>
	*
	* Copyright (C) 2007 MontaVista Software, Inc.
	* Anton Vorontsov <avorontsov@ru.mvista.com>
	*
	* This program is free software; you can redistribute it and/or
	* modify it under the terms of the GNU General Public License as
	* published by the Free Software Foundation; either version 2 of
	* the License, or (at your option) any later version.
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	#undef DEBUG

	/*
	* High Level Configuration Options
	*/
	#define CONFIG_E300 1 /* E300 family */
	#define CONFIG_QE 1 /* Has QE */
	#define CONFIG_MPC83XX 1 /* MPC83XX family */
	#define CONFIG_MPC8360 1 /* MPC8360 CPU specific */
	#define CONFIG_MPC8360ERDK 1 /* MPC8360ERDK board specific */

	/*
	* System Clock Setup
	*/
	#ifdef CONFIG_CLKIN_33MHZ
	#define CONFIG_83XX_CLKIN 33000000
	#define CONFIG_SYS_CLK_FREQ 33000000
	#define PCI_33M 1
	#define HRCWL_CSB_TO_CLKIN_MPC8360ERDK HRCWL_CSB_TO_CLKIN_10X1
	#else
	#define CONFIG_83XX_CLKIN 66000000
	#define CONFIG_SYS_CLK_FREQ 66000000
	#define PCI_66M 1
	#define HRCWL_CSB_TO_CLKIN_MPC8360ERDK HRCWL_CSB_TO_CLKIN_5X1
	#endif /* CONFIG_CLKIN_33MHZ */

	/*
	* Hardware Reset Configuration Word
	*/
	#define CFG_HRCW_LOW (\
	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 \|\
	HRCWL_DDR_TO_SCB_CLK_1X1 \|\
	HRCWL_CSB_TO_CLKIN_MPC8360ERDK \|\
	HRCWL_CORE_TO_CSB_2X1 \|\
	HRCWL_CE_TO_PLL_1X15)

	#define CFG_HRCW_HIGH (\
	HRCWH_PCI_HOST \|\
	HRCWH_PCI1_ARBITER_ENABLE \|\
	HRCWH_PCICKDRV_ENABLE \|\
	HRCWH_CORE_ENABLE \|\
	HRCWH_FROM_0X00000100 \|\
	HRCWH_BOOTSEQ_DISABLE \|\
	HRCWH_SW_WATCHDOG_DISABLE \|\
	HRCWH_ROM_LOC_LOCAL_16BIT \|\
	HRCWH_SECONDARY_DDR_DISABLE \|\
	HRCWH_BIG_ENDIAN \|\
	HRCWH_LALE_EARLY)

	/*
	* System IO Config
	*/
	#define CFG_SICRH 0x00000000
	#define CFG_SICRL 0x40000000

	#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
	#define CONFIG_BOARD_EARLY_INIT_R

	/*
	* IMMR new address
	*/
	#define CFG_IMMR 0xE0000000

	/*
	* DDR Setup
	*/
	#define CFG_DDR_BASE 0x00000000 /* DDR is system memory */
	#define CFG_SDRAM_BASE CFG_DDR_BASE
	#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
	#define CFG_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \| \
	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)

	#define CFG_83XX_DDR_USES_CS0

	#undef CONFIG_DDR_ECC /* support DDR ECC function */
	#undef CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */

	/*
	* DDRCDR - DDR Control Driver Register
	*/
	#define CFG_DDRCDR_VALUE 0x80080001

	#undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup */

	/*
	* Manually set up DDR parameters
	*/
	#define CONFIG_DDR_II
	#define CFG_DDR_SIZE 256 /* MB */
	#define CFG_DDRCDR 0x80080001
	#define CFG_DDR_CS0_BNDS 0x0000000f
	#define CFG_DDR_CS0_CONFIG (CSCONFIG_EN \| CSCONFIG_ROW_BIT_13 \| \
	CSCONFIG_COL_BIT_10)
	#define CFG_DDR_TIMING_0 0x00330903
	#define CFG_DDR_TIMING_1 0x3835a322
	#define CFG_DDR_TIMING_2 0x00104909
	#define CFG_DDR_TIMING_3 0x00000000
	#define CFG_DDR_CLK_CNTL 0x02000000
	#define CFG_DDR_MODE 0x47800432
	#define CFG_DDR_MODE2 0x8000c000
	#define CFG_DDR_INTERVAL 0x045b0100
	#define CFG_DDR_SDRAM_CFG 0x03000000
	#define CFG_DDR_SDRAM_CFG2 0x00001000

	/*
	* Memory test
	*/
	#undef CFG_DRAM_TEST /* memory test, takes time */
	#define CFG_MEMTEST_START 0x00000000 /* memtest region */
	#define CFG_MEMTEST_END 0x00100000

	/*
	* The reserved memory
	*/
	#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
	#define CFG_FLASH_BASE 0xFF800000 /* FLASH base address */

	#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
	#define CFG_RAMBOOT
	#else
	#undef CFG_RAMBOOT
	#endif

	#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
	#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */

	/*
	* Initial RAM Base Address Setup
	*/
	#define CFG_INIT_RAM_LOCK 1
	#define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
	#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */
	#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
	#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)

	/*
	* Local Bus Configuration & Clock Setup
	*/
	#define CFG_LCRR (LCRR_DBYP \| LCRR_CLKDIV_4)
	#define CFG_LBC_LBCR 0x00000000

	/*
	* FLASH on the Local Bus
	*/
	#define CFG_FLASH_CFI /* use the Common Flash Interface */
	#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
	#define CFG_FLASH_SIZE 8 /* max FLASH size is 32M */
	#define CFG_FLASH_PROTECTION 1 /* Use intel Flash protection. */

	#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */
	#define CFG_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */

	#define CFG_BR0_PRELIM (CFG_FLASH_BASE \| /* Flash Base address */ \
	(2 << BR_PS_SHIFT) \| /* 16 bit port size */ \
	BR_V) /* valid */
	#define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) \| OR_UPM_XAM \| \
	OR_GPCM_CSNT \| OR_GPCM_ACS_0b11 \| \
	OR_GPCM_XACS \| OR_GPCM_SCY_15 \| \
	OR_GPCM_TRLX \| OR_GPCM_EHTR \| OR_GPCM_EAD)

	#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
	#define CFG_MAX_FLASH_SECT 256 /* max sectors per device */

	#undef CFG_FLASH_CHECKSUM

	/*
	* NAND flash on the local bus
	*/
	#define CFG_NAND_BASE 0x60000000

	#define CFG_LBLAWBAR1_PRELIM CFG_NAND_BASE
	#define CFG_LBLAWAR1_PRELIM 0x8000001b /* Access window size 4K */

	/* Port size 8 bit, UPMA */
	#define CFG_BR1_PRELIM (CFG_NAND_BASE \| 0x00000881)
	#define CFG_OR1_PRELIM 0xfc000001

	/*
	* Fujitsu MB86277 (MINT) graphics controller
	*/
	#define CFG_VIDEO_BASE 0x70000000

	#define CFG_LBLAWBAR2_PRELIM CFG_VIDEO_BASE
	#define CFG_LBLAWAR2_PRELIM 0x80000019 /* Access window size 64MB */

	/* Port size 32 bit, UPMB */
	#define CFG_BR2_PRELIM (CFG_VIDEO_BASE \| 0x000018a1) /* PS=11, UPMB */
	#define CFG_OR2_PRELIM 0xfc000001 /* (64MB, EAD=1) */

	/*
	* Serial Port
	*/
	#define CONFIG_CONS_INDEX 1
	#undef CONFIG_SERIAL_SOFTWARE_FIFO
	#define CFG_NS16550
	#define CFG_NS16550_SERIAL
	#define CFG_NS16550_REG_SIZE 1
	#define CFG_NS16550_CLK get_bus_freq(0)

	#define CFG_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200,}

	#define CFG_NS16550_COM1 (CFG_IMMR+0x4500)
	#define CFG_NS16550_COM2 (CFG_IMMR+0x4600)

	#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
	/* Use the HUSH parser */
	#define CFG_HUSH_PARSER
	#ifdef CFG_HUSH_PARSER
	#define CFG_PROMPT_HUSH_PS2 "> "
	#endif

	/* Pass open firmware flat tree */
	#define CONFIG_OF_LIBFDT 1
	#define CONFIG_OF_BOARD_SETUP 1

	/* I2C */
	#define CONFIG_HARD_I2C /* I2C with hardware support */
	#undef CONFIG_SOFT_I2C /* I2C bit-banged */
	#define CONFIG_FSL_I2C
	#define CONFIG_I2C_MULTI_BUS
	#define CONFIG_I2C_CMD_TREE
	#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
	#define CFG_I2C_SLAVE 0x7F
	#define CFG_I2C_NOPROBES {{0x52}} /* Don't probe these addrs */
	#define CFG_I2C_OFFSET 0x3000
	#define CFG_I2C2_OFFSET 0x3100

	/*
	* General PCI
	* Addresses are mapped 1-1.
	*/
	#define CONFIG_PCI
	#define CONFIG_83XX_GENERIC_PCI 1

	#define CFG_PCI1_MEM_BASE 0x80000000
	#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
	#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
	#define CFG_PCI1_MMIO_BASE 0x90000000
	#define CFG_PCI1_MMIO_PHYS CFG_PCI1_MMIO_BASE
	#define CFG_PCI1_MMIO_SIZE 0x10000000 /* 256M */
	#define CFG_PCI1_IO_BASE 0xE0300000
	#define CFG_PCI1_IO_PHYS 0xE0300000
	#define CFG_PCI1_IO_SIZE 0x100000 /* 1M */

	#ifdef CONFIG_PCI

	#define CONFIG_NET_MULTI
	#define CONFIG_PCI_PNP /* do pci plug-and-play */

	#undef CONFIG_EEPRO100
	#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
	#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */

	#endif /* CONFIG_PCI */


	#ifndef CONFIG_NET_MULTI
	#define CONFIG_NET_MULTI 1
	#endif

	/*
	* QE UEC ethernet configuration
	*/
	#define CONFIG_UEC_ETH
	#define CONFIG_ETHPRIME "Freescale GETH"

	#define CONFIG_UEC_ETH1 /* GETH1 */

	#ifdef CONFIG_UEC_ETH1
	#define CFG_UEC1_UCC_NUM 0 /* UCC1 */
	#define CFG_UEC1_RX_CLK QE_CLK_NONE
	#define CFG_UEC1_TX_CLK QE_CLK9
	#define CFG_UEC1_ETH_TYPE GIGA_ETH
	#define CFG_UEC1_PHY_ADDR 2
	#define CFG_UEC1_INTERFACE_MODE ENET_1000_GMII
	#endif

	#define CONFIG_UEC_ETH2 /* GETH2 */

	#ifdef CONFIG_UEC_ETH2
	#define CFG_UEC2_UCC_NUM 1 /* UCC2 */
	#define CFG_UEC2_RX_CLK QE_CLK_NONE
	#define CFG_UEC2_TX_CLK QE_CLK4
	#define CFG_UEC2_ETH_TYPE GIGA_ETH
	#define CFG_UEC2_PHY_ADDR 4
	#define CFG_UEC2_INTERFACE_MODE ENET_1000_GMII
	#endif

	/*
	* Environment
	*/

	#ifndef CFG_RAMBOOT
	#define CFG_ENV_IS_IN_FLASH 1
	#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
	#define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
	#define CFG_ENV_SIZE 0x20000
	#else /* CFG_RAMBOOT */
	#define CFG_NO_FLASH 1 /* Flash is not usable now */
	#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
	#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
	#define CFG_ENV_SIZE 0x2000
	#endif /* CFG_RAMBOOT */

	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */

	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME


	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#define CONFIG_CMD_PING
	#define CONFIG_CMD_I2C
	#define CONFIG_CMD_ASKENV

	#if defined(CONFIG_PCI)
	#define CONFIG_CMD_PCI
	#endif

	#if defined(CFG_RAMBOOT)
	#undef CONFIG_CMD_ENV
	#undef CONFIG_CMD_LOADS
	#endif

	#undef CONFIG_WATCHDOG /* watchdog disabled */

	/*
	* Miscellaneous configurable options
	*/
	#define CFG_LONGHELP /* undef to save memory */
	#define CFG_LOAD_ADDR 0x2000000 /* default load address */
	#define CFG_PROMPT "=> " /* Monitor Command Prompt */

	#if defined(CONFIG_CMD_KGDB)
	#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
	#endif

	#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
	#define CFG_MAXARGS 16 /* max number of command args */
	#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
	#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */

	/*
	* Core HID Setup
	*/
	#define CFG_HID0_INIT 0x000000000
	#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK
	#define CFG_HID2 HID2_HBE

	/*
	* Cache Config
	*/
	#define CFG_DCACHE_SIZE 32768
	#define CFG_CACHELINE_SIZE 32
	#if defined(CONFIG_CMD_KGDB)
	#define CFG_CACHELINE_SHIFT 5 /log base 2 of the above value /
	#endif

	/*
	* MMU Setup
	*/

	/* DDR: cache cacheable */
	#define CFG_IBAT0L (CFG_SDRAM_BASE \| BATL_PP_10 \| BATL_MEMCOHERENCE)
	#define CFG_IBAT0U (CFG_SDRAM_BASE \| BATU_BL_256M \| BATU_VS \| BATU_VP)
	#define CFG_DBAT0L CFG_IBAT0L
	#define CFG_DBAT0U CFG_IBAT0U

	/* IMMRBAR & PCI IO: cache-inhibit and guarded */
	#define CFG_IBAT1L (CFG_IMMR \| BATL_PP_10 \| \
	BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CFG_IBAT1U (CFG_IMMR \| BATU_BL_4M \| BATU_VS \| BATU_VP)
	#define CFG_DBAT1L CFG_IBAT1L
	#define CFG_DBAT1U CFG_IBAT1U

	/* NAND: cache-inhibit and guarded */
	#define CFG_IBAT2L (CFG_NAND_BASE \| BATL_PP_10 \| BATL_CACHEINHIBIT \|\
	BATL_GUARDEDSTORAGE)
	#define CFG_IBAT2U (CFG_NAND_BASE \| BATU_BL_64M \| BATU_VS \| BATU_VP)
	#define CFG_DBAT2L CFG_IBAT2L
	#define CFG_DBAT2U CFG_IBAT2U

	/* FLASH: icache cacheable, but dcache-inhibit and guarded */
	#define CFG_IBAT3L (CFG_FLASH_BASE \| BATL_PP_10 \| BATL_MEMCOHERENCE)
	#define CFG_IBAT3U (CFG_FLASH_BASE \| BATU_BL_32M \| BATU_VS \| BATU_VP)
	#define CFG_DBAT3L (CFG_FLASH_BASE \| BATL_PP_10 \| \
	BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CFG_DBAT3U CFG_IBAT3U

	/* Stack in dcache: cacheable, no memory coherence */
	#define CFG_IBAT4L (CFG_INIT_RAM_ADDR \| BATL_PP_10)
	#define CFG_IBAT4U (CFG_INIT_RAM_ADDR \| BATU_BL_128K \| BATU_VS \| BATU_VP)
	#define CFG_DBAT4L CFG_IBAT4L
	#define CFG_DBAT4U CFG_IBAT4U

	#define CFG_IBAT5L (CFG_VIDEO_BASE \| BATL_PP_10 \| BATL_CACHEINHIBIT \| \
	BATL_GUARDEDSTORAGE)
	#define CFG_IBAT5U (CFG_VIDEO_BASE \| BATU_BL_64M \| BATU_VS \| BATU_VP)
	#define CFG_DBAT5L CFG_IBAT5L
	#define CFG_DBAT5U CFG_IBAT5U

	#ifdef CONFIG_PCI
	/* PCI MEM space: cacheable */
	#define CFG_IBAT6L (CFG_PCI1_MEM_PHYS \| BATL_PP_10 \| BATL_MEMCOHERENCE)
	#define CFG_IBAT6U (CFG_PCI1_MEM_PHYS \| BATU_BL_256M \| BATU_VS \| BATU_VP)
	#define CFG_DBAT6L CFG_IBAT6L
	#define CFG_DBAT6U CFG_IBAT6U
	/* PCI MMIO space: cache-inhibit and guarded */
	#define CFG_IBAT7L (CFG_PCI1_MMIO_PHYS \| BATL_PP_10 \| \
	BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CFG_IBAT7U (CFG_PCI1_MMIO_PHYS \| BATU_BL_256M \| BATU_VS \| BATU_VP)
	#define CFG_DBAT7L CFG_IBAT7L
	#define CFG_DBAT7U CFG_IBAT7U
	#else /* CONFIG_PCI */
	#define CFG_IBAT6L (0)
	#define CFG_IBAT6U (0)
	#define CFG_IBAT7L (0)
	#define CFG_IBAT7U (0)
	#define CFG_DBAT6L CFG_IBAT6L
	#define CFG_DBAT6U CFG_IBAT6U
	#define CFG_DBAT7L CFG_IBAT7L
	#define CFG_DBAT7U CFG_IBAT7U
	#endif /* CONFIG_PCI */

	/*
	* Internal Definitions
	*
	* Boot Flags
	*/
	#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
	#define BOOTFLAG_WARM 0x02 /* Software reboot */

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
	#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
	#endif

	/*
	* Environment Configuration
	*/
	#define CONFIG_ENV_OVERWRITE

	#if defined(CONFIG_UEC_ETH)
	#define CONFIG_HAS_ETH0
	#define CONFIG_HAS_ETH1
	#define CONFIG_HAS_ETH2
	#define CONFIG_HAS_ETH3
	#define CONFIG_ETHADDR 00:04:9f:ef:01:01
	#define CONFIG_ETH1ADDR 00:04:9f:ef:01:02
	#define CONFIG_ETH2ADDR 00:04:9f:ef:01:03
	#define CONFIG_ETH3ADDR 00:04:9f:ef:01:04
	#endif

	#define CONFIG_BAUDRATE 115200

	#define CONFIG_LOADADDR a00000
	#define CONFIG_HOSTNAME mpc8360erdk
	#define CONFIG_BOOTFILE uImage

	#define CONFIG_IPADDR 10.0.0.99
	#define CONFIG_SERVERIP 10.0.0.2
	#define CONFIG_GATEWAYIP 10.0.0.2
	#define CONFIG_NETMASK 255.255.255.0
	#define CONFIG_ROOTPATH /nfsroot/

	#define CONFIG_BOOTDELAY 2 /* -1 disables auto-boot */
	#undef CONFIG_BOOTARGS /* the boot command will set bootargs */

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0"\
	"consoledev=ttyS0\0"\
	"loadaddr=a00000\0"\
	"fdtaddr=900000\0"\
	"bootfile=uImage\0"\
	"fdtfile=dtb\0"\
	"fsfile=fs\0"\
	"ubootfile=u-boot.bin\0"\
	"setbootargs=setenv bootargs console=$consoledev,$baudrate "\
	"$mtdparts panic=1\0"\
	"adddhcpargs=setenv bootargs $bootargs ip=on\0"\
	"addnfsargs=setenv bootargs $bootargs ip=$ipaddr:$serverip:"\
	"$gatewayip:$netmask:$hostname:$netdev:off "\
	"root=/dev/nfs rw nfsroot=$serverip:$rootpath\0"\
	"tftp_get_uboot=tftp 100000 $ubootfile\0"\
	"tftp_get_kernel=tftp $loadaddr $bootfile\0"\
	"tftp_get_dtb=tftp $fdtaddr $fdtfile\0"\
	"tftp_get_fs=tftp c00000 $fsfile\0"\
	"nor_reflash=protect off ff800000 ff87ffff ; erase ff800000 ff87ffff ; "\
	"cp.b 100000 ff800000 $filesize\0"\
	"boot_m=bootm $loadaddr - $fdtaddr\0"\
	"dhcpboot=run setbootargs adddhcpargs tftp_get_kernel tftp_get_dtb "\
	"boot_m\0"\
	"nfsboot=run setbootargs addnfsargs tftp_get_kernel tftp_get_dtb "\
	"boot_m\0"\
	""

	#define CONFIG_BOOTCOMMAND "run dhcpboot"

	#endif /* __CONFIG_H */