include/configs/ls2080a_common.h - filogic/uboot - Gitiles

 /*
  * Copyright 2017 NXP
  * Copyright (C) 2014 Freescale Semiconductor
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __LS2_COMMON_H
 #define __LS2_COMMON_H

 #define CONFIG_REMAKE_ELF
 #define CONFIG_FSL_LAYERSCAPE
 #define CONFIG_MP
 #define CONFIG_GICV3
 #define CONFIG_FSL_TZPC_BP147

 #include <asm/arch/stream_id_lsch3.h>
 #include <asm/arch/config.h>

 /* Link Definitions */
 #define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)

 /* We need architecture specific misc initializations */

 /* Link Definitions */
 #ifndef CONFIG_QSPI_BOOT
 #ifdef CONFIG_SPL
 #define CONFIG_SYS_TEXT_BASE		0x80400000
 #else
 #define CONFIG_SYS_TEXT_BASE		0x30100000
 #endif
 #else
 #define CONFIG_SYS_TEXT_BASE		0x20100000
 #define CONFIG_ENV_SIZE			0x2000          /* 8KB */
 #define CONFIG_ENV_OFFSET		0x300000        /* 3MB */
 #define CONFIG_ENV_SECT_SIZE		0x40000
 #endif

 #define CONFIG_SUPPORT_RAW_INITRD

 #define CONFIG_SKIP_LOWLEVEL_INIT

 #ifndef CONFIG_SPL
 #define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
 #endif
 #ifndef CONFIG_SYS_FSL_DDR4
 #define CONFIG_SYS_DDR_RAW_TIMING
 #endif

 #define CONFIG_SYS_FSL_DDR_INTLV_256B	/* force 256 byte interleaving */

 #define CONFIG_VERY_BIG_RAM
 #define CONFIG_SYS_DDR_SDRAM_BASE	0x80000000UL
 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
 #define CONFIG_SYS_DDR_BLOCK2_BASE	0x8080000000ULL
 #define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS	2

 /*
  * SMP Definitinos
  */
 #define CPU_RELEASE_ADDR		secondary_boot_func

 #define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR
 #define CONFIG_SYS_DP_DDR_BASE		0x6000000000ULL
 /*
  * DDR controller use 0 as the base address for binding.
  * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
  */
 #define CONFIG_SYS_DP_DDR_BASE_PHY	0
 #define CONFIG_DP_DDR_CTRL		2
 #define CONFIG_DP_DDR_NUM_CTRLS		1
 #endif

 /* Generic Timer Definitions */
 /*
  * This is not an accurate number. It is used in start.S. The frequency
  * will be udpated later when get_bus_freq(0) is available.
  */
 #define COUNTER_FREQUENCY		25000000	/* 25MHz */

 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 2048 * 1024)

 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_MXC
 #define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
 #define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
 #define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
 #define CONFIG_SYS_I2C_MXC_I2C4		/* enable I2C bus 4 */

 /* Serial Port */
 #define CONFIG_CONS_INDEX       1
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE     1
 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())

 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }

 /* IFC */
 #define CONFIG_FSL_IFC

 /*
  * During booting, IFC is mapped at the region of 0x30000000.
  * But this region is limited to 256MB. To accommodate NOR, promjet
  * and FPGA. This region is divided as below:
  * 0x30000000 - 0x37ffffff : 128MB : NOR flash
  * 0x38000000 - 0x3BFFFFFF : 64MB  : Promjet
  * 0x3C000000 - 0x40000000 : 64MB  : FPGA etc
  *
  * To accommodate bigger NOR flash and other devices, we will map IFC
  * chip selects to as below:
  * 0x5_1000_0000..0x5_1fff_ffff	Memory Hole
  * 0x5_2000_0000..0x5_3fff_ffff	IFC CSx (FPGA, NAND and others 512MB)
  * 0x5_4000_0000..0x5_7fff_ffff	ASIC or others 1GB
  * 0x5_8000_0000..0x5_bfff_ffff	IFC CS0 1GB (NOR/Promjet)
  * 0x5_C000_0000..0x5_ffff_ffff	IFC CS1 1GB (NOR/Promjet)
  *
  * For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation.
  * CONFIG_SYS_FLASH_BASE has the final address (core view)
  * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
  * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
  * CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
  */

 #define CONFIG_SYS_FLASH_BASE			0x580000000ULL
 #define CONFIG_SYS_FLASH_BASE_PHYS		0x80000000
 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY	0x00000000

 #define CONFIG_SYS_FLASH1_BASE_PHYS		0xC0000000
 #define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY	0x8000000

 #ifndef __ASSEMBLY__
 unsigned long long get_qixis_addr(void);
 #endif
 #define QIXIS_BASE				get_qixis_addr()
 #define QIXIS_BASE_PHYS				0x20000000
 #define QIXIS_BASE_PHYS_EARLY			0xC000000
 #define QIXIS_STAT_PRES1			0xb
 #define QIXIS_SDID_MASK				0x07
 #define QIXIS_ESDHC_NO_ADAPTER			0x7

 #define CONFIG_SYS_NAND_BASE			0x530000000ULL
 #define CONFIG_SYS_NAND_BASE_PHYS		0x30000000

 /* MC firmware */
 /* TODO Actual DPL max length needs to be confirmed with the MC FW team */
 #define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH	    0x20000
 #define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET    0x00F00000
 #define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH	    0x20000
 #define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET    0x00F20000
 /* For LS2085A */
 #define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH	0x200000
 #define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET	0x07000000

 /* Define phy_reset function to boot the MC based on mcinitcmd.
  * This happens late enough to properly fixup u-boot env MAC addresses.
  */
 #define CONFIG_RESET_PHY_R

 /*
  * Carve out a DDR region which will not be used by u-boot/Linux
  *
  * It will be used by MC and Debug Server. The MC region must be
  * 512MB aligned, so the min size to hide is 512MB.
  */
 #ifdef CONFIG_FSL_MC_ENET
 #define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE		(512UL * 1024 * 1024)
 #endif

 /* Command line configuration */

 /* Miscellaneous configurable options */
 #define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)

 /* Physical Memory Map */
 /* fixme: these need to be checked against the board */
 #define CONFIG_CHIP_SELECTS_PER_CTRL	4

 #define CONFIG_NR_DRAM_BANKS		3

 #define CONFIG_HWCONFIG
 #define HWCONFIG_BUFFER_SIZE		128

 /* Allow to overwrite serial and ethaddr */
 #define CONFIG_ENV_OVERWRITE

 /* Initial environment variables */
 #define CONFIG_EXTRA_ENV_SETTINGS		\
 	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
 	"loadaddr=0x80100000\0"			\
 	"kernel_addr=0x100000\0"		\
 	"ramdisk_addr=0x800000\0"		\
 	"ramdisk_size=0x2000000\0"		\
 	"fdt_high=0xa0000000\0"			\
 	"initrd_high=0xffffffffffffffff\0"	\
 	"kernel_start=0x581000000\0"		\
 	"kernel_load=0xa0000000\0"		\
 	"kernel_size=0x2800000\0"		\
 	"console=ttyAMA0,38400n8\0"		\
 	"mcinitcmd=fsl_mc start mc 0x580a00000"	\
 	" 0x580e00000 \0"

 #ifdef CONFIG_SD_BOOT
 #define CONFIG_BOOTCOMMAND	"mmc read 0x80200000 0x6800 0x800;"\
 				" fsl_mc apply dpl 0x80200000 &&" \
 				" mmc read $kernel_load $kernel_start" \
 				" $kernel_size && bootm $kernel_load"
 #else
 #define CONFIG_BOOTCOMMAND	"fsl_mc apply dpl 0x580d00000 &&" \
 				" cp.b $kernel_start $kernel_load" \
 				" $kernel_size && bootm $kernel_load"
 #endif

 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
 #define CONFIG_SYS_LONGHELP
 #define CONFIG_CMDLINE_EDITING		1
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_MAXARGS		64	/* max command args */

 #define CONFIG_PANIC_HANG	/* do not reset board on panic */

 #define CONFIG_SPL_BSS_START_ADDR	0x80100000
 #define CONFIG_SPL_BSS_MAX_SIZE		0x00100000
 #define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_MAX_SIZE		0x16000
 #define CONFIG_SPL_STACK		(CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
 #define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
 #define CONFIG_SPL_TEXT_BASE		0x1800a000

 #ifdef CONFIG_NAND_BOOT
 #define CONFIG_SYS_NAND_U_BOOT_DST	0x80400000
 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST
 #endif
 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x00100000
 #define CONFIG_SYS_SPL_MALLOC_START	0x80200000
 #define CONFIG_SYS_MONITOR_LEN		(1024 * 1024)

 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */

 #include <asm/arch/soc.h>

 #endif /* __LS2_COMMON_H */
	/*
	* Copyright 2017 NXP
	* Copyright (C) 2014 Freescale Semiconductor
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __LS2_COMMON_H
	#define __LS2_COMMON_H

	#define CONFIG_REMAKE_ELF
	#define CONFIG_FSL_LAYERSCAPE
	#define CONFIG_MP
	#define CONFIG_GICV3
	#define CONFIG_FSL_TZPC_BP147

	#include <asm/arch/stream_id_lsch3.h>
	#include <asm/arch/config.h>

	/* Link Definitions */
	#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)

	/* We need architecture specific misc initializations */

	/* Link Definitions */
	#ifndef CONFIG_QSPI_BOOT
	#ifdef CONFIG_SPL
	#define CONFIG_SYS_TEXT_BASE 0x80400000
	#else
	#define CONFIG_SYS_TEXT_BASE 0x30100000
	#endif
	#else
	#define CONFIG_SYS_TEXT_BASE 0x20100000
	#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
	#define CONFIG_ENV_OFFSET 0x300000 /* 3MB */
	#define CONFIG_ENV_SECT_SIZE 0x40000
	#endif

	#define CONFIG_SUPPORT_RAW_INITRD

	#define CONFIG_SKIP_LOWLEVEL_INIT

	#ifndef CONFIG_SPL
	#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
	#endif
	#ifndef CONFIG_SYS_FSL_DDR4
	#define CONFIG_SYS_DDR_RAW_TIMING
	#endif

	#define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */

	#define CONFIG_VERY_BIG_RAM
	#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
	#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
	#define CONFIG_SYS_DDR_BLOCK2_BASE 0x8080000000ULL
	#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 2

	/*
	* SMP Definitinos
	*/
	#define CPU_RELEASE_ADDR secondary_boot_func

	#define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
	#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
	#define CONFIG_SYS_DP_DDR_BASE 0x6000000000ULL
	/*
	* DDR controller use 0 as the base address for binding.
	* It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
	*/
	#define CONFIG_SYS_DP_DDR_BASE_PHY 0
	#define CONFIG_DP_DDR_CTRL 2
	#define CONFIG_DP_DDR_NUM_CTRLS 1
	#endif

	/* Generic Timer Definitions */
	/*
	* This is not an accurate number. It is used in start.S. The frequency
	* will be udpated later when get_bus_freq(0) is available.
	*/
	#define COUNTER_FREQUENCY 25000000 /* 25MHz */

	/* Size of malloc() pool */
	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2048 * 1024)

	/* I2C */
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_MXC
	#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
	#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
	#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
	#define CONFIG_SYS_I2C_MXC_I2C4 /* enable I2C bus 4 */

	/* Serial Port */
	#define CONFIG_CONS_INDEX 1
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#define CONFIG_SYS_NS16550_CLK (get_serial_clock())

	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }

	/* IFC */
	#define CONFIG_FSL_IFC

	/*
	* During booting, IFC is mapped at the region of 0x30000000.
	* But this region is limited to 256MB. To accommodate NOR, promjet
	* and FPGA. This region is divided as below:
	* 0x30000000 - 0x37ffffff : 128MB : NOR flash
	* 0x38000000 - 0x3BFFFFFF : 64MB : Promjet
	* 0x3C000000 - 0x40000000 : 64MB : FPGA etc
	*
	* To accommodate bigger NOR flash and other devices, we will map IFC
	* chip selects to as below:
	* 0x5_1000_0000..0x5_1fff_ffff Memory Hole
	* 0x5_2000_0000..0x5_3fff_ffff IFC CSx (FPGA, NAND and others 512MB)
	* 0x5_4000_0000..0x5_7fff_ffff ASIC or others 1GB
	* 0x5_8000_0000..0x5_bfff_ffff IFC CS0 1GB (NOR/Promjet)
	* 0x5_C000_0000..0x5_ffff_ffff IFC CS1 1GB (NOR/Promjet)
	*
	* For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation.
	* CONFIG_SYS_FLASH_BASE has the final address (core view)
	* CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
	* CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
	* CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
	*/

	#define CONFIG_SYS_FLASH_BASE 0x580000000ULL
	#define CONFIG_SYS_FLASH_BASE_PHYS 0x80000000
	#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000

	#define CONFIG_SYS_FLASH1_BASE_PHYS 0xC0000000
	#define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY 0x8000000

	#ifndef __ASSEMBLY__
	unsigned long long get_qixis_addr(void);
	#endif
	#define QIXIS_BASE get_qixis_addr()
	#define QIXIS_BASE_PHYS 0x20000000
	#define QIXIS_BASE_PHYS_EARLY 0xC000000
	#define QIXIS_STAT_PRES1 0xb
	#define QIXIS_SDID_MASK 0x07
	#define QIXIS_ESDHC_NO_ADAPTER 0x7

	#define CONFIG_SYS_NAND_BASE 0x530000000ULL
	#define CONFIG_SYS_NAND_BASE_PHYS 0x30000000

	/* MC firmware */
	/* TODO Actual DPL max length needs to be confirmed with the MC FW team */
	#define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000
	#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000
	#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000
	#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000
	/* For LS2085A */
	#define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH 0x200000
	#define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET 0x07000000

	/* Define phy_reset function to boot the MC based on mcinitcmd.
	* This happens late enough to properly fixup u-boot env MAC addresses.
	*/
	#define CONFIG_RESET_PHY_R

	/*
	* Carve out a DDR region which will not be used by u-boot/Linux
	*
	* It will be used by MC and Debug Server. The MC region must be
	* 512MB aligned, so the min size to hide is 512MB.
	*/
	#ifdef CONFIG_FSL_MC_ENET
	#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (512UL * 1024 * 1024)
	#endif

	/* Command line configuration */

	/* Miscellaneous configurable options */
	#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)

	/* Physical Memory Map */
	/* fixme: these need to be checked against the board */
	#define CONFIG_CHIP_SELECTS_PER_CTRL 4

	#define CONFIG_NR_DRAM_BANKS 3

	#define CONFIG_HWCONFIG
	#define HWCONFIG_BUFFER_SIZE 128

	/* Allow to overwrite serial and ethaddr */
	#define CONFIG_ENV_OVERWRITE

	/* Initial environment variables */
	#define CONFIG_EXTRA_ENV_SETTINGS \
	"hwconfig=fsl_ddr:bank_intlv=auto\0" \
	"loadaddr=0x80100000\0" \
	"kernel_addr=0x100000\0" \
	"ramdisk_addr=0x800000\0" \
	"ramdisk_size=0x2000000\0" \
	"fdt_high=0xa0000000\0" \
	"initrd_high=0xffffffffffffffff\0" \
	"kernel_start=0x581000000\0" \
	"kernel_load=0xa0000000\0" \
	"kernel_size=0x2800000\0" \
	"console=ttyAMA0,38400n8\0" \
	"mcinitcmd=fsl_mc start mc 0x580a00000" \
	" 0x580e00000 \0"

	#ifdef CONFIG_SD_BOOT
	#define CONFIG_BOOTCOMMAND "mmc read 0x80200000 0x6800 0x800;"\
	" fsl_mc apply dpl 0x80200000 &&" \
	" mmc read $kernel_load $kernel_start" \
	" $kernel_size && bootm $kernel_load"
	#else
	#define CONFIG_BOOTCOMMAND "fsl_mc apply dpl 0x580d00000 &&" \
	" cp.b $kernel_start $kernel_load" \
	" $kernel_size && bootm $kernel_load"
	#endif

	/* Monitor Command Prompt */
	#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
	#define CONFIG_SYS_LONGHELP
	#define CONFIG_CMDLINE_EDITING 1
	#define CONFIG_AUTO_COMPLETE
	#define CONFIG_SYS_MAXARGS 64 /* max command args */

	#define CONFIG_PANIC_HANG /* do not reset board on panic */

	#define CONFIG_SPL_BSS_START_ADDR 0x80100000
	#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
	#define CONFIG_SPL_FRAMEWORK
	#define CONFIG_SPL_MAX_SIZE 0x16000
	#define CONFIG_SPL_STACK (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
	#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
	#define CONFIG_SPL_TEXT_BASE 0x1800a000

	#ifdef CONFIG_NAND_BOOT
	#define CONFIG_SYS_NAND_U_BOOT_DST 0x80400000
	#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
	#endif
	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000
	#define CONFIG_SYS_SPL_MALLOC_START 0x80200000
	#define CONFIG_SYS_MONITOR_LEN (1024 * 1024)

	#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */

	#include <asm/arch/soc.h>

	#endif /* __LS2_COMMON_H */