| /* |
| * (C) Copyright 2009 |
| * Matthias Fuchs, esd gmbh germany, matthias.fuchs@esd.eu |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #define CONFIG_405EP 1 /* This is a PPC405 CPU */ |
| #define CONFIG_PMC405DE 1 /* ...on a PMC405DE board */ |
| |
| #define CONFIG_SYS_TEXT_BASE 0xFFFC0000 |
| |
| #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ |
| #define CONFIG_BOARD_TYPES 1 /* support board types */ |
| |
| #define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */ |
| |
| #undef CONFIG_BOOTARGS |
| #undef CONFIG_BOOTCOMMAND |
| |
| #define CONFIG_PREBOOT /* enable preboot variable */ |
| |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change*/ |
| |
| #define CONFIG_HAS_ETH1 |
| |
| #define CONFIG_PPC4xx_EMAC |
| #define CONFIG_MII 1 /* MII PHY management */ |
| #define CONFIG_PHY_ADDR 1 /* PHY address */ |
| #define CONFIG_PHY1_ADDR 2 /* 2nd PHY address */ |
| |
| #define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_SUBNETMASK |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_DNS |
| #define CONFIG_BOOTP_DNS2 |
| #define CONFIG_BOOTP_SEND_HOSTNAME |
| |
| /* |
| * Command line configuration. |
| */ |
| #define CONFIG_CMD_IRQ |
| #define CONFIG_CMD_PCI |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| #define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ |
| #define CONFIG_PRAM 0 |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP |
| |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */ |
| |
| #define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x3000000 /* 1 ... 48 MB in DRAM */ |
| |
| #define CONFIG_CONS_INDEX 2 /* Use UART1 */ |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK get_serial_clock() |
| |
| #undef CONFIG_SYS_EXT_SERIAL_CLOCK |
| #define CONFIG_SYS_BASE_BAUD 691200 |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ |
| #define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ |
| |
| #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ |
| #define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ |
| |
| /* |
| * PCI stuff |
| */ |
| #define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ |
| #define PCI_HOST_FORCE 1 /* configure as pci host */ |
| #define PCI_HOST_AUTO 2 /* detected via arbiter enable */ |
| |
| #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ |
| #define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ |
| |
| #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| |
| /* |
| * PCI identification |
| */ |
| #define CONFIG_SYS_PCI_SUBSYS_VENDORID PCI_VENDOR_ID_ESDGMBH |
| #define CONFIG_SYS_PCI_SUBSYS_ID_NONMONARCH 0x040e /* Dev ID: Non-Monarch */ |
| #define CONFIG_SYS_PCI_SUBSYS_ID_MONARCH 0x040f /* Dev ID: Monarch */ |
| #define CONFIG_SYS_PCI_CLASSCODE_NONMONARCH PCI_CLASS_PROCESSOR_POWERPC |
| #define CONFIG_SYS_PCI_CLASSCODE_MONARCH PCI_CLASS_BRIDGE_HOST |
| |
| #define CONFIG_SYS_PCI_CLASSCODE CONFIG_SYS_PCI_CLASSCODE_MONARCH |
| #define CONFIG_SYS_PCI_SUBSYS_DEVICEID CONFIG_SYS_PCI_SUBSYS_ID_MONARCH |
| |
| #define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ |
| #define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable=1 */ |
| #define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ |
| #define CONFIG_SYS_PCI_PTM2LA 0xef000000 /* point to CPLD, GPIO */ |
| #define CONFIG_SYS_PCI_PTM2MS 0xff000001 /* 16MB, enable=1 */ |
| #define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ |
| |
| #define CONFIG_PCI_4xx_PTM_OVERWRITE 1 /* overwrite PTMx settings by env */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) |
| /* |
| * FLASH organization |
| */ |
| #define CONFIG_SYS_FLASH_CFI 1 /* CFI compatible */ |
| #define CONFIG_FLASH_CFI_DRIVER 1 /* Use common CFI driver */ |
| |
| #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max. no. memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max sectors per chip */ |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* erase timeout (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* write timeout (in ms) */ |
| |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* buffered writes (faster) */ |
| #define CONFIG_SYS_FLASH_PROTECTION 1 /* hardware flash protection */ |
| |
| #define CONFIG_SYS_FLASH_EMPTY_INFO 1 /* 'E' for empty sector (flinfo) */ |
| #define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ |
| |
| /* |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 |
| */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_FLASH_BASE 0xfe000000 |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_MONITOR_LEN (~(CONFIG_SYS_TEXT_BASE) + 1) |
| #define CONFIG_SYS_MALLOC_LEN (256 * 1024) |
| |
| /* |
| * Environment in EEPROM setup |
| */ |
| #define CONFIG_ENV_IS_IN_EEPROM 1 |
| #define CONFIG_ENV_OFFSET 0x100 |
| #define CONFIG_ENV_SIZE 0x700 |
| |
| /* |
| * I2C EEPROM (24W16) for environment |
| */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_PPC4XX |
| #define CONFIG_SYS_I2C_PPC4XX_CH0 |
| #define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 |
| #define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F |
| |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM 24W16 */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ |
| /* mask of address bits that overflow into the "EEPROM chip address" */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ |
| /* 16 byte page write mode using*/ |
| /* last 4 bits of the address */ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ |
| #define CONFIG_SYS_EEPROM_WREN 1 |
| |
| #define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x50 |
| #define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0x40 |
| #define CONFIG_4xx_CONFIG_BLOCKSIZE 0x20 |
| |
| /* |
| * RTC |
| */ |
| #define CONFIG_RTC_RX8025 |
| |
| /* |
| * External Bus Controller (EBC) Setup |
| * (max. 55MHZ EBC clock) |
| */ |
| /* Memory Bank 0 (NOR flash) BAS=0xFE0,BS=32MB,BU=R/W,BW=16bit */ |
| #define CONFIG_SYS_EBC_PB0AP 0x03017200 |
| #define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH_BASE | 0xba000) |
| |
| /* Memory Bank 1 (CPLD) BAS=0xEF0,BS=16MB,BU=R/W,BW=16bit */ |
| #define CONFIG_SYS_CPLD_BASE 0xef000000 |
| #define CONFIG_SYS_EBC_PB1AP 0x00800000 |
| #define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_CPLD_BASE | 0x18000) |
| |
| /* |
| * Definitions for initial stack pointer and data area (in data cache) |
| */ |
| /* use on chip memory ( OCM ) for temperary stack until sdram is tested */ |
| #define CONFIG_SYS_TEMP_STACK_OCM 1 |
| |
| /* On Chip Memory location */ |
| #define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 |
| #define CONFIG_SYS_OCM_DATA_SIZE 0x1000 |
| /* inside SDRAM */ |
| #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR |
| /* End of used area in RAM */ |
| #define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE |
| |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ |
| GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /* |
| * GPIO Configuration |
| */ |
| #define CONFIG_SYS_4xx_GPIO_TABLE { /* GPIO Alt1 */ \ |
| { \ |
| /* GPIO Core 0 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO0 PerBLast */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO1 TS1E */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO2 TS2E */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO3 TS1O */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO4 TS2O */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_1 }, /* GPIO5 TS3 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_1 }, /* GPIO6 TS4 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_1 }, /* GPIO7 TS5 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO8 TS6 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_1 }, /* GPIO9 TrcClk */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO10 PerCS1 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO11 PerCS2 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO12 PerCS3 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO13 PerCS4 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO14 PerAddr03 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO15 PerAddr04 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO16 PerAddr05 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO17 IRQ0 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO18 IRQ1 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO19 IRQ2 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO20 IRQ3 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO21 IRQ4 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO22 IRQ5 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO23 IRQ6 */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO24 UART0_DCD */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO25 UART0_DSR */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO26 UART0_RI */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO27 UART0_DTR */ \ |
| { GPIO_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO28 UART1_Rx */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO29 UART1_Tx */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO30 RejectPkt0 */ \ |
| { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO31 RejectPkt1 */ \ |
| } \ |
| } |
| |
| #define CONFIG_SYS_GPIO_HWREV_MASK (0xf0000000 >> 1) /* GPIO1..4 */ |
| #define CONFIG_SYS_GPIO_HWREV_SHIFT 27 |
| #define CONFIG_SYS_GPIO_LEDRUN_N (0x80000000 >> 5) /* GPIO5 */ |
| #define CONFIG_SYS_GPIO_LEDA_N (0x80000000 >> 6) /* GPIO6 */ |
| #define CONFIG_SYS_GPIO_LEDB_N (0x80000000 >> 7) /* GPIO7 */ |
| #define CONFIG_SYS_GPIO_SELFRST_N (0x80000000 >> 8) /* GPIO8 */ |
| #define CONFIG_SYS_GPIO_EEPROM_WP (0x80000000 >> 9) /* GPIO9 */ |
| #define CONFIG_SYS_GPIO_MONARCH_N (0x80000000 >> 11) /* GPIO11 */ |
| #define CONFIG_SYS_GPIO_EREADY (0x80000000 >> 12) /* GPIO12 */ |
| #define CONFIG_SYS_GPIO_M66EN (0x80000000 >> 13) /* GPIO13 */ |
| |
| /* |
| * Default speed selection (cpu_plb_opb_ebc) in mhz. |
| * This value will be set if iic boot eprom is disabled. |
| */ |
| #undef CONFIG_SYS_FCPU333MHZ |
| #define CONFIG_SYS_FCPU266MHZ |
| #undef CONFIG_SYS_FCPU133MHZ |
| |
| #if defined(CONFIG_SYS_FCPU333MHZ) |
| /* |
| * CPU: 333MHz |
| * PLB/SDRAM/MAL: 111MHz |
| * OPB: 55MHz |
| * EBC: 55MHz |
| * PCI: 55MHz (111MHz on M66EN=1) |
| */ |
| #define PLLMR0_DEFAULT (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ |
| PLL_OPBDIV_2 | PLL_EXTBUSDIV_2 | \ |
| PLL_MALDIV_1 | PLL_PCIDIV_2) |
| #define PLLMR1_DEFAULT (PLL_FBKDIV_10 | \ |
| PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ |
| PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI) |
| #endif |
| |
| #if defined(CONFIG_SYS_FCPU266MHZ) |
| /* |
| * CPU: 266MHz |
| * PLB/SDRAM/MAL: 133MHz |
| * OPB: 66MHz |
| * EBC: 44MHz |
| * PCI: 44MHz (66MHz on M66EN=1) |
| */ |
| #define PLLMR0_DEFAULT (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ |
| PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ |
| PLL_MALDIV_1 | PLL_PCIDIV_3) |
| #define PLLMR1_DEFAULT (PLL_FBKDIV_8 | \ |
| PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ |
| PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) |
| #endif |
| |
| #if defined(CONFIG_SYS_FCPU133MHZ) |
| /* |
| * CPU: 133MHz |
| * PLB/SDRAM/MAL: 133MHz |
| * OPB: 66MHz |
| * EBC: 44MHz |
| * PCI: 44MHz (66MHz on M66EN=1) |
| */ |
| #define PLLMR0_DEFAULT (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \ |
| PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ |
| PLL_MALDIV_1 | PLL_PCIDIV_3) |
| #define PLLMR1_DEFAULT (PLL_FBKDIV_4 | \ |
| PLL_FWDDIVA_6 | PLL_FWDDIVB_6 | \ |
| PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) |
| #endif |
| |
| #endif /* __CONFIG_H */ |