| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Copyright (C) 2010 Albert ARIBAUD <albert.u.boot@aribaud.net> |
| * |
| * Based on original Kirkwood support which is |
| * (C) Copyright 2009 |
| * Marvell Semiconductor <www.marvell.com> |
| * Written-by: Prafulla Wadaskar <prafulla@marvell.com> |
| */ |
| |
| #ifndef _CONFIG_EDMINIV2_H |
| #define _CONFIG_EDMINIV2_H |
| |
| /* |
| * SPL |
| */ |
| |
| #define CONFIG_SYS_UBOOT_BASE 0xfff90000 |
| #define CONFIG_SYS_UBOOT_START 0x00800000 |
| |
| /* |
| * High Level Configuration Options (easy to change) |
| */ |
| |
| #include <asm/arch/orion5x.h> |
| /* |
| * CLKs configurations |
| */ |
| |
| /* |
| * Board-specific values for Orion5x MPP low level init: |
| * - MPPs 12 to 15 are SATA LEDs (mode 5) |
| * - Others are GPIO/unused (mode 3 for MPP0, mode 5 for |
| * MPP16 to MPP19, mode 0 for others |
| */ |
| |
| #define ORION5X_MPP0_7 0x00000003 |
| #define ORION5X_MPP8_15 0x55550000 |
| #define ORION5X_MPP16_23 0x00005555 |
| |
| /* |
| * Board-specific values for Orion5x GPIO low level init: |
| * - GPIO3 is input (RTC interrupt) |
| * - GPIO16 is Power LED control (0 = on, 1 = off) |
| * - GPIO17 is Power LED source select (0 = CPLD, 1 = GPIO16) |
| * - GPIO18 is Power Button status (0 = Released, 1 = Pressed) |
| * - GPIO19 is SATA disk power toggle (toggles on 0-to-1) |
| * - GPIO22 is SATA disk power status () |
| * - GPIO23 is supply status for SATA disk () |
| * - GPIO24 is supply control for board (write 1 to power off) |
| * Last GPIO is 25, further bits are supposed to be 0. |
| * Enable mask has ones for INPUT, 0 for OUTPUT. |
| * Default is LED ON, board ON :) |
| */ |
| |
| #define ORION5X_GPIO_OUT_ENABLE 0xfef4f0ca |
| #define ORION5X_GPIO_OUT_VALUE 0x00000000 |
| #define ORION5X_GPIO_IN_POLARITY 0x000000d0 |
| |
| /* |
| * NS16550 Configuration |
| */ |
| |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE (-4) |
| #define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK |
| #define CONFIG_SYS_NS16550_COM1 ORION5X_UART0_BASE |
| |
| /* |
| * Serial Port configuration |
| * The following definitions let you select what serial you want to use |
| * for your console driver. |
| */ |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| { 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600 } |
| |
| /* |
| * FLASH configuration |
| */ |
| |
| #define CONFIG_SYS_FLASH_BASE 0xfff80000 |
| |
| /* auto boot */ |
| |
| /* |
| * Network |
| */ |
| |
| #ifdef CONFIG_CMD_NET |
| #define CONFIG_MVGBE_PORTS {1} /* enable port 0 only */ |
| #define CONFIG_SKIP_LOCAL_MAC_RANDOMIZATION /* don't randomize MAC */ |
| #define CONFIG_PHY_BASE_ADR 0x8 |
| #endif |
| |
| /* |
| * IDE |
| */ |
| #ifdef CONFIG_IDE |
| #define __io |
| /* Data, registers and alternate blocks are at the same offset */ |
| /* Each 8-bit ATA register is aligned to a 4-bytes address */ |
| /* A single bus, a single device */ |
| /* ATA registers base is at SATA controller base */ |
| /* ATA bus 0 is orion5x port 1 on ED Mini V2 */ |
| /* end of IDE defines */ |
| #endif /* CMD_IDE */ |
| |
| /* |
| * Common USB/EHCI configuration |
| */ |
| #ifdef CONFIG_CMD_USB |
| #define ORION5X_USB20_HOST_PORT_BASE ORION5X_USB20_PORT0_BASE |
| #endif /* CONFIG_CMD_USB */ |
| |
| /* |
| * I2C related stuff |
| */ |
| #ifdef CONFIG_CMD_I2C |
| #define CONFIG_I2C_MVTWSI_BASE0 ORION5X_TWSI_BASE |
| #endif |
| |
| /* |
| * Environment variables configurations |
| */ |
| |
| /* Enable command line editing */ |
| |
| /* provide extensive help */ |
| |
| /* additions for new relocation code, must be added to all boards */ |
| #define CONFIG_SYS_SDRAM_BASE 0 |
| |
| #endif /* _CONFIG_EDMINIV2_H */ |