| /* |
| * Copyright 2015 Freescale Semiconductor |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __LS2_RDB_H |
| #define __LS2_RDB_H |
| |
| #include "ls2080a_common.h" |
| |
| #undef CONFIG_CONS_INDEX |
| #define CONFIG_CONS_INDEX 2 |
| |
| #define I2C_MUX_CH_VOL_MONITOR 0xa |
| #define I2C_VOL_MONITOR_ADDR 0x38 |
| #define CONFIG_VOL_MONITOR_IR36021_READ |
| #define CONFIG_VOL_MONITOR_IR36021_SET |
| |
| #define CONFIG_VID_FLS_ENV "ls2080ardb_vdd_mv" |
| #ifndef CONFIG_SPL_BUILD |
| #define CONFIG_VID |
| #endif |
| /* step the IR regulator in 5mV increments */ |
| #define IR_VDD_STEP_DOWN 5 |
| #define IR_VDD_STEP_UP 5 |
| /* The lowest and highest voltage allowed for LS2080ARDB */ |
| #define VDD_MV_MIN 819 |
| #define VDD_MV_MAX 1212 |
| |
| #ifndef __ASSEMBLY__ |
| unsigned long get_board_sys_clk(void); |
| #endif |
| |
| #define CONFIG_SYS_FSL_CLK |
| #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() |
| #define CONFIG_DDR_CLK_FREQ 133333333 |
| #define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4) |
| |
| #define CONFIG_DDR_SPD |
| #define CONFIG_DDR_ECC |
| #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER |
| #define CONFIG_MEM_INIT_VALUE 0xdeadbeef |
| #define SPD_EEPROM_ADDRESS1 0x51 |
| #define SPD_EEPROM_ADDRESS2 0x52 |
| #define SPD_EEPROM_ADDRESS3 0x53 |
| #define SPD_EEPROM_ADDRESS4 0x54 |
| #define SPD_EEPROM_ADDRESS5 0x55 |
| #define SPD_EEPROM_ADDRESS6 0x56 /* dummy address */ |
| #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 |
| #define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */ |
| #define CONFIG_DIMM_SLOTS_PER_CTLR 2 |
| #define CONFIG_CHIP_SELECTS_PER_CTRL 4 |
| #ifdef CONFIG_SYS_FSL_HAS_DP_DDR |
| #define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1 |
| #endif |
| #define CONFIG_FSL_DDR_BIST /* enable built-in memory test */ |
| |
| /* SATA */ |
| #define CONFIG_LIBATA |
| #define CONFIG_SCSI_AHCI |
| #define CONFIG_SCSI_AHCI_PLAT |
| #define CONFIG_SCSI |
| #define CONFIG_DOS_PARTITION |
| #define CONFIG_BOARD_LATE_INIT |
| |
| #define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1 |
| #define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2 |
| |
| #define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 |
| #define CONFIG_SYS_SCSI_MAX_LUN 1 |
| #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ |
| CONFIG_SYS_SCSI_MAX_LUN) |
| |
| /* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */ |
| |
| #define CONFIG_SYS_NOR0_CSPR_EXT (0x0) |
| #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) |
| #define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(64*1024*1024) |
| |
| #define CONFIG_SYS_NOR0_CSPR \ |
| (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CONFIG_SYS_NOR0_CSPR_EARLY \ |
| (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12) |
| #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ |
| FTIM0_NOR_TEADC(0x5) | \ |
| FTIM0_NOR_TEAHC(0x5)) |
| #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ |
| FTIM1_NOR_TRAD_NOR(0x1a) |\ |
| FTIM1_NOR_TSEQRAD_NOR(0x13)) |
| #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ |
| FTIM2_NOR_TCH(0x4) | \ |
| FTIM2_NOR_TWPH(0x0E) | \ |
| FTIM2_NOR_TWP(0x1c)) |
| #define CONFIG_SYS_NOR_FTIM3 0x04000000 |
| #define CONFIG_SYS_IFC_CCR 0x01000000 |
| |
| #ifndef CONFIG_SYS_NO_FLASH |
| #define CONFIG_FLASH_CFI_DRIVER |
| #define CONFIG_SYS_FLASH_CFI |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE |
| #define CONFIG_SYS_FLASH_QUIET_TEST |
| #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\ |
| CONFIG_SYS_FLASH_BASE + 0x40000000} |
| #endif |
| |
| #define CONFIG_NAND_FSL_IFC |
| #define CONFIG_SYS_NAND_MAX_ECCPOS 256 |
| #define CONFIG_SYS_NAND_MAX_OOBFREE 2 |
| |
| #define CONFIG_SYS_NAND_CSPR_EXT (0x0) |
| #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ |
| | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ |
| | CSPR_MSEL_NAND /* MSEL = NAND */ \ |
| | CSPR_V) |
| #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) |
| |
| #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ |
| | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ |
| | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ |
| | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \ |
| | CSOR_NAND_PGS_4K /* Page Size = 4K */ \ |
| | CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \ |
| | CSOR_NAND_PB(128)) /* Pages Per Block 128*/ |
| |
| #define CONFIG_SYS_NAND_ONFI_DETECTION |
| |
| /* ONFI NAND Flash mode0 Timing Params */ |
| #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x0e) | \ |
| FTIM0_NAND_TWP(0x30) | \ |
| FTIM0_NAND_TWCHT(0x0e) | \ |
| FTIM0_NAND_TWH(0x14)) |
| #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x64) | \ |
| FTIM1_NAND_TWBE(0xab) | \ |
| FTIM1_NAND_TRR(0x1c) | \ |
| FTIM1_NAND_TRP(0x30)) |
| #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x1e) | \ |
| FTIM2_NAND_TREH(0x14) | \ |
| FTIM2_NAND_TWHRE(0x3c)) |
| #define CONFIG_SYS_NAND_FTIM3 0x0 |
| |
| #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_MTD_NAND_VERIFY_WRITE |
| #define CONFIG_CMD_NAND |
| |
| #define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) |
| |
| #define CONFIG_FSL_QIXIS /* use common QIXIS code */ |
| #define QIXIS_LBMAP_SWITCH 0x06 |
| #define QIXIS_LBMAP_MASK 0x0f |
| #define QIXIS_LBMAP_SHIFT 0 |
| #define QIXIS_LBMAP_DFLTBANK 0x00 |
| #define QIXIS_LBMAP_ALTBANK 0x04 |
| #define QIXIS_LBMAP_NAND 0x09 |
| #define QIXIS_RST_CTL_RESET 0x31 |
| #define QIXIS_RST_CTL_RESET_EN 0x30 |
| #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 |
| #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 |
| #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 |
| #define QIXIS_RCW_SRC_NAND 0x119 |
| #define QIXIS_RST_FORCE_MEM 0x01 |
| |
| #define CONFIG_SYS_CSPR3_EXT (0x0) |
| #define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \ |
| | CSPR_PORT_SIZE_8 \ |
| | CSPR_MSEL_GPCM \ |
| | CSPR_V) |
| #define CONFIG_SYS_CSPR3_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ |
| | CSPR_PORT_SIZE_8 \ |
| | CSPR_MSEL_GPCM \ |
| | CSPR_V) |
| |
| #define CONFIG_SYS_AMASK3 IFC_AMASK(64*1024) |
| #define CONFIG_SYS_CSOR3 CSOR_GPCM_ADM_SHIFT(12) |
| /* QIXIS Timing parameters for IFC CS3 */ |
| #define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ |
| FTIM0_GPCM_TEADC(0x0e) | \ |
| FTIM0_GPCM_TEAHC(0x0e)) |
| #define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ |
| FTIM1_GPCM_TRAD(0x3f)) |
| #define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0xf) | \ |
| FTIM2_GPCM_TCH(0xf) | \ |
| FTIM2_GPCM_TWP(0x3E)) |
| #define CONFIG_SYS_CS3_FTIM3 0x0 |
| |
| #if defined(CONFIG_SPL) && defined(CONFIG_NAND) |
| #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT |
| #define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR_EARLY |
| #define CONFIG_SYS_CSPR2_FINAL CONFIG_SYS_NOR0_CSPR |
| #define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT |
| #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR |
| #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK |
| #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR |
| #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 |
| #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 |
| #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 |
| #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 |
| |
| #define CONFIG_ENV_IS_IN_NAND |
| #define CONFIG_ENV_OFFSET (2048 * 1024) |
| #define CONFIG_ENV_SECT_SIZE 0x20000 |
| #define CONFIG_ENV_SIZE 0x2000 |
| #define CONFIG_SPL_PAD_TO 0x80000 |
| #define CONFIG_SYS_NAND_U_BOOT_OFFS (1024 * 1024) |
| #define CONFIG_SYS_NAND_U_BOOT_SIZE (512 * 1024) |
| #else |
| #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT |
| #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY |
| #define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR |
| #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT |
| #define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR |
| #define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK |
| #define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR |
| #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 |
| #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 |
| #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 |
| #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 |
| |
| #define CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x200000) |
| #define CONFIG_ENV_SECT_SIZE 0x20000 |
| #define CONFIG_ENV_SIZE 0x2000 |
| #endif |
| |
| /* Debug Server firmware */ |
| #define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR |
| #define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL |
| |
| #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000 |
| |
| /* |
| * I2C |
| */ |
| #define I2C_MUX_PCA_ADDR 0x75 |
| #define I2C_MUX_PCA_ADDR_PRI 0x75 /* Primary Mux*/ |
| |
| /* I2C bus multiplexer */ |
| #define I2C_MUX_CH_DEFAULT 0x8 |
| |
| /* SPI */ |
| #ifdef CONFIG_FSL_DSPI |
| #define CONFIG_SPI_FLASH |
| #define CONFIG_SPI_FLASH_BAR |
| #endif |
| |
| /* |
| * RTC configuration |
| */ |
| #define RTC |
| #define CONFIG_RTC_DS3231 1 |
| #define CONFIG_SYS_I2C_RTC_ADDR 0x68 |
| #define CONFIG_CMD_DATE |
| |
| /* EEPROM */ |
| #define CONFIG_ID_EEPROM |
| #define CONFIG_CMD_EEPROM |
| #define CONFIG_SYS_I2C_EEPROM_NXID |
| #define CONFIG_SYS_EEPROM_BUS_NUM 0 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 |
| |
| #define CONFIG_FSL_MEMAC |
| #define CONFIG_PCIE_LAYERSCAPE /* Use common FSL Layerscape PCIe code */ |
| |
| #ifdef CONFIG_PCI |
| #define CONFIG_PCI_SCAN_SHOW |
| #define CONFIG_CMD_PCI |
| #endif |
| |
| /* MMC */ |
| #define CONFIG_MMC |
| #ifdef CONFIG_MMC |
| #define CONFIG_FSL_ESDHC |
| #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 |
| #define CONFIG_GENERIC_MMC |
| #define CONFIG_DOS_PARTITION |
| #endif |
| |
| #define CONFIG_MISC_INIT_R |
| |
| /* |
| * USB |
| */ |
| #define CONFIG_HAS_FSL_XHCI_USB |
| #define CONFIG_USB_XHCI_FSL |
| #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 |
| #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2 |
| |
| #undef CONFIG_CMDLINE_EDITING |
| #include <config_distro_defaults.h> |
| |
| #define BOOT_TARGET_DEVICES(func) \ |
| func(USB, usb, 0) \ |
| func(MMC, mmc, 0) \ |
| func(SCSI, scsi, 0) \ |
| func(DHCP, dhcp, na) |
| #include <config_distro_bootcmd.h> |
| |
| /* Initial environment variables */ |
| #undef CONFIG_EXTRA_ENV_SETTINGS |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "hwconfig=fsl_ddr:bank_intlv=auto\0" \ |
| "scriptaddr=0x80800000\0" \ |
| "kernel_addr_r=0x81000000\0" \ |
| "pxefile_addr_r=0x81000000\0" \ |
| "fdt_addr_r=0x88000000\0" \ |
| "ramdisk_addr_r=0x89000000\0" \ |
| "loadaddr=0x80100000\0" \ |
| "kernel_addr=0x100000\0" \ |
| "ramdisk_addr=0x800000\0" \ |
| "ramdisk_size=0x2000000\0" \ |
| "fdt_high=0xa0000000\0" \ |
| "initrd_high=0xffffffffffffffff\0" \ |
| "kernel_start=0x581100000\0" \ |
| "kernel_load=0xa0000000\0" \ |
| "kernel_size=0x2800000\0" \ |
| "fdtfile=fsl-ls2080a-rdb.dtb\0" \ |
| "mcinitcmd=fsl_mc start mc 0x580300000" \ |
| " 0x580800000 \0" \ |
| BOOTENV |
| |
| #undef CONFIG_BOOTARGS |
| #define CONFIG_BOOTARGS "console=ttyS1,115200 root=/dev/ram0 " \ |
| "earlycon=uart8250,mmio,0x21c0600 " \ |
| "ramdisk_size=0x2000000 default_hugepagesz=2m" \ |
| " hugepagesz=2m hugepages=256" |
| |
| #undef CONFIG_BOOTCOMMAND |
| /* Try to boot an on-NOR kernel first, then do normal distro boot */ |
| #define CONFIG_BOOTCOMMAND "run mcinitcmd && fsl_mc lazyapply dpl 0x580700000" \ |
| " && cp.b $kernel_start $kernel_load $kernel_size" \ |
| " && bootm $kernel_load" \ |
| " || run distro_bootcmd" |
| |
| /* MAC/PHY configuration */ |
| #ifdef CONFIG_FSL_MC_ENET |
| #define CONFIG_PHYLIB_10G |
| #define CONFIG_PHY_AQUANTIA |
| #define CONFIG_PHY_CORTINA |
| #define CONFIG_PHYLIB |
| #define CONFIG_SYS_CORTINA_FW_IN_NOR |
| #define CONFIG_CORTINA_FW_ADDR 0x581000000 |
| #define CONFIG_CORTINA_FW_LENGTH 0x40000 |
| |
| #define CORTINA_PHY_ADDR1 0x10 |
| #define CORTINA_PHY_ADDR2 0x11 |
| #define CORTINA_PHY_ADDR3 0x12 |
| #define CORTINA_PHY_ADDR4 0x13 |
| #define AQ_PHY_ADDR1 0x00 |
| #define AQ_PHY_ADDR2 0x01 |
| #define AQ_PHY_ADDR3 0x02 |
| #define AQ_PHY_ADDR4 0x03 |
| #define AQR405_IRQ_MASK 0x36 |
| |
| #define CONFIG_MII |
| #define CONFIG_ETHPRIME "DPMAC1@xgmii" |
| #define CONFIG_PHY_GIGE |
| #define CONFIG_PHY_AQUANTIA |
| #endif |
| |
| #include <asm/fsl_secure_boot.h> |
| |
| #endif /* __LS2_RDB_H */ |