| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * (C) Copyright 2014-2015 Freescale Semiconductor |
| * Copyright 2019-2022 NXP |
| * |
| * Extracted from armv8/start.S |
| */ |
| |
| #include <config.h> |
| #include <linux/linkage.h> |
| #include <asm/gic.h> |
| #include <asm/macro.h> |
| #include <asm/arch-fsl-layerscape/soc.h> |
| #ifdef CONFIG_FSL_LSCH3 |
| #include <asm/arch-fsl-layerscape/immap_lsch3.h> |
| #endif |
| #include <asm/u-boot.h> |
| |
| .align 3 |
| .weak secondary_boot_addr |
| secondary_boot_addr: |
| .quad 0 |
| |
| /* Get GIC offset |
| * For LS1043a rev1.0, GIC base address align with 4k. |
| * For LS1043a rev1.1, if DCFG_GIC400_ALIGN[GIC_ADDR_BIT] |
| * is set, GIC base address align with 4K, or else align |
| * with 64k. |
| * output: |
| * x0: the base address of GICD |
| * x1: the base address of GICC |
| */ |
| ENTRY(get_gic_offset) |
| ldr x0, =GICD_BASE |
| #ifdef CONFIG_GICV2 |
| ldr x1, =GICC_BASE |
| #endif |
| #ifdef CONFIG_HAS_FEATURE_GIC64K_ALIGN |
| ldr x2, =DCFG_CCSR_SVR |
| ldr w2, [x2] |
| rev w2, w2 |
| lsr w3, w2, #16 |
| ldr w4, =SVR_DEV(SVR_LS1043A) |
| cmp w3, w4 |
| b.ne 1f |
| ands w2, w2, #0xff |
| cmp w2, #REV1_0 |
| b.eq 1f |
| ldr x2, =SCFG_GIC400_ALIGN |
| ldr w2, [x2] |
| rev w2, w2 |
| tbnz w2, #GIC_ADDR_BIT, 1f |
| ldr x0, =GICD_BASE_64K |
| #ifdef CONFIG_GICV2 |
| ldr x1, =GICC_BASE_64K |
| #endif |
| 1: |
| #endif |
| ret |
| ENDPROC(get_gic_offset) |
| |
| ENTRY(smp_kick_all_cpus) |
| /* Kick secondary cpus up by SGI 0 interrupt */ |
| #if defined(CONFIG_GICV2) || defined(CONFIG_GICV3) |
| mov x29, lr /* Save LR */ |
| bl get_gic_offset |
| bl gic_kick_secondary_cpus |
| mov lr, x29 /* Restore LR */ |
| #endif |
| ret |
| ENDPROC(smp_kick_all_cpus) |
| |
| |
| ENTRY(lowlevel_init) |
| mov x29, lr /* Save LR */ |
| |
| switch_el x1, 1f, 100f, 100f /* skip if not in EL3 */ |
| 1: |
| |
| #if defined (CONFIG_SYS_FSL_HAS_CCN504) |
| |
| /* Set Wuo bit for RN-I 20 */ |
| #ifdef CONFIG_ARCH_LS2080A |
| ldr x0, =CCI_AUX_CONTROL_BASE(20) |
| ldr x1, =0x00000010 |
| bl ccn504_set_aux |
| |
| /* |
| * Set forced-order mode in RNI-6, RNI-20 |
| * This is required for performance optimization on LS2088A |
| * LS2080A family does not support setting forced-order mode, |
| * so skip this operation for LS2080A family |
| */ |
| bl get_svr |
| lsr w0, w0, #16 |
| ldr w1, =SVR_DEV(SVR_LS2080A) |
| cmp w0, w1 |
| b.eq 1f |
| |
| ldr x0, =CCI_AUX_CONTROL_BASE(6) |
| ldr x1, =0x00000020 |
| bl ccn504_set_aux |
| ldr x0, =CCI_AUX_CONTROL_BASE(20) |
| ldr x1, =0x00000020 |
| bl ccn504_set_aux |
| 1: |
| #endif |
| |
| /* Add fully-coherent masters to DVM domain */ |
| ldr x0, =CCI_MN_BASE |
| ldr x1, =CCI_MN_RNF_NODEID_LIST |
| ldr x2, =CCI_MN_DVM_DOMAIN_CTL_SET |
| bl ccn504_add_masters_to_dvm |
| |
| /* Set all RN-I ports to QoS of 15 */ |
| ldr x0, =CCI_S0_QOS_CONTROL_BASE(0) |
| ldr x1, =0x00FF000C |
| bl ccn504_set_qos |
| ldr x0, =CCI_S1_QOS_CONTROL_BASE(0) |
| ldr x1, =0x00FF000C |
| bl ccn504_set_qos |
| ldr x0, =CCI_S2_QOS_CONTROL_BASE(0) |
| ldr x1, =0x00FF000C |
| bl ccn504_set_qos |
| |
| ldr x0, =CCI_S0_QOS_CONTROL_BASE(2) |
| ldr x1, =0x00FF000C |
| bl ccn504_set_qos |
| ldr x0, =CCI_S1_QOS_CONTROL_BASE(2) |
| ldr x1, =0x00FF000C |
| bl ccn504_set_qos |
| ldr x0, =CCI_S2_QOS_CONTROL_BASE(2) |
| ldr x1, =0x00FF000C |
| bl ccn504_set_qos |
| |
| ldr x0, =CCI_S0_QOS_CONTROL_BASE(6) |
| ldr x1, =0x00FF000C |
| bl ccn504_set_qos |
| ldr x0, =CCI_S1_QOS_CONTROL_BASE(6) |
| ldr x1, =0x00FF000C |
| bl ccn504_set_qos |
| ldr x0, =CCI_S2_QOS_CONTROL_BASE(6) |
| ldr x1, =0x00FF000C |
| bl ccn504_set_qos |
| |
| ldr x0, =CCI_S0_QOS_CONTROL_BASE(12) |
| ldr x1, =0x00FF000C |
| bl ccn504_set_qos |
| ldr x0, =CCI_S1_QOS_CONTROL_BASE(12) |
| ldr x1, =0x00FF000C |
| bl ccn504_set_qos |
| ldr x0, =CCI_S2_QOS_CONTROL_BASE(12) |
| ldr x1, =0x00FF000C |
| bl ccn504_set_qos |
| |
| ldr x0, =CCI_S0_QOS_CONTROL_BASE(16) |
| ldr x1, =0x00FF000C |
| bl ccn504_set_qos |
| ldr x0, =CCI_S1_QOS_CONTROL_BASE(16) |
| ldr x1, =0x00FF000C |
| bl ccn504_set_qos |
| ldr x0, =CCI_S2_QOS_CONTROL_BASE(16) |
| ldr x1, =0x00FF000C |
| bl ccn504_set_qos |
| |
| ldr x0, =CCI_S0_QOS_CONTROL_BASE(20) |
| ldr x1, =0x00FF000C |
| bl ccn504_set_qos |
| ldr x0, =CCI_S1_QOS_CONTROL_BASE(20) |
| ldr x1, =0x00FF000C |
| bl ccn504_set_qos |
| ldr x0, =CCI_S2_QOS_CONTROL_BASE(20) |
| ldr x1, =0x00FF000C |
| bl ccn504_set_qos |
| #endif /* CONFIG_SYS_FSL_HAS_CCN504 */ |
| |
| #ifdef SMMU_BASE |
| /* Set the SMMU page size in the sACR register */ |
| ldr x1, =SMMU_BASE |
| ldr w0, [x1, #0x10] |
| orr w0, w0, #1 << 16 /* set sACR.pagesize to indicate 64K page */ |
| str w0, [x1, #0x10] |
| #endif |
| |
| /* Initialize GIC Secure Bank Status */ |
| #if !defined(CONFIG_SPL_BUILD) |
| #if defined(CONFIG_GICV2) || defined(CONFIG_GICV3) |
| branch_if_slave x0, 1f |
| bl get_gic_offset |
| bl gic_init_secure |
| 1: |
| #ifdef CONFIG_GICV3 |
| ldr x0, =GICR_BASE |
| bl gic_init_secure_percpu |
| #elif defined(CONFIG_GICV2) |
| bl get_gic_offset |
| bl gic_init_secure_percpu |
| #endif |
| #endif |
| #endif |
| |
| 100: |
| branch_if_master x0, 2f |
| |
| #if defined(CONFIG_MP) && defined(CONFIG_ARMV8_MULTIENTRY) |
| /* |
| * Formerly, here was a jump to secondary_boot_func, but we just |
| * return early here and let the generic code in start.S handle |
| * the jump to secondary_boot_func. |
| */ |
| mov lr, x29 /* Restore LR */ |
| ret |
| #endif |
| |
| 2: |
| switch_el x1, 1f, 100f, 100f /* skip if not in EL3 */ |
| 1: |
| #ifdef CONFIG_FSL_TZPC_BP147 |
| /* Set Non Secure access for all devices protected via TZPC */ |
| ldr x1, =TZPCDECPROT_0_SET_BASE /* Decode Protection-0 Set Reg */ |
| orr w0, w0, #1 << 3 /* DCFG_RESET is accessible from NS world */ |
| str w0, [x1] |
| |
| isb |
| dsb sy |
| #endif |
| |
| #ifdef CONFIG_FSL_TZASC_400 |
| /* |
| * LS2080 and its personalities does not support TZASC |
| * So skip TZASC related operations |
| */ |
| bl get_svr |
| lsr w0, w0, #16 |
| ldr w1, =SVR_DEV(SVR_LS2080A) |
| cmp w0, w1 |
| b.eq 1f |
| |
| /* Set TZASC so that: |
| * a. We use only Region0 whose global secure write/read is EN |
| * b. We use only Region0 whose NSAID write/read is EN |
| * |
| * NOTE: As per the CCSR map doc, TZASC 3 and TZASC 4 are just |
| * placeholders. |
| */ |
| |
| .macro tzasc_prog, xreg |
| |
| mov x12, TZASC1_BASE |
| mov x16, #0x10000 |
| mul x14, \xreg, x16 |
| add x14, x14,x12 |
| mov x1, #0x8 |
| add x1, x1, x14 |
| |
| ldr w0, [x1] /* Filter 0 Gate Keeper Register */ |
| orr w0, w0, #1 << 0 /* Set open_request for Filter 0 */ |
| str w0, [x1] |
| |
| mov x1, #0x110 |
| add x1, x1, x14 |
| |
| ldr w0, [x1] /* Region-0 Attributes Register */ |
| orr w0, w0, #1 << 31 /* Set Sec global write en, Bit[31] */ |
| orr w0, w0, #1 << 30 /* Set Sec global read en, Bit[30] */ |
| str w0, [x1] |
| |
| mov x1, #0x114 |
| add x1, x1, x14 |
| |
| ldr w0, [x1] /* Region-0 Access Register */ |
| mov w0, #0xFFFFFFFF /* Set nsaid_wr_en and nsaid_rd_en */ |
| str w0, [x1] |
| .endm |
| |
| #ifdef CONFIG_FSL_TZASC_1 |
| mov x13, #0 |
| tzasc_prog x13 |
| |
| #endif |
| #ifdef CONFIG_FSL_TZASC_2 |
| mov x13, #1 |
| tzasc_prog x13 |
| |
| #endif |
| isb |
| dsb sy |
| #endif |
| 100: |
| 1: |
| #ifdef CONFIG_ARCH_LS1046A |
| switch_el x1, 1f, 100f, 100f /* skip if not in EL3 */ |
| 1: |
| /* Initialize the L2 RAM latency */ |
| mrs x1, S3_1_c11_c0_2 |
| mov x0, #0x1C7 |
| /* Clear L2 Tag RAM latency and L2 Data RAM latency */ |
| bic x1, x1, x0 |
| /* Set L2 data ram latency bits [2:0] */ |
| orr x1, x1, #0x2 |
| /* set L2 tag ram latency bits [8:6] */ |
| orr x1, x1, #0x80 |
| msr S3_1_c11_c0_2, x1 |
| isb |
| 100: |
| #endif |
| |
| #if !defined(CONFIG_TFABOOT) && \ |
| (defined(CONFIG_FSL_LSCH2) && !defined(CONFIG_SPL_BUILD)) |
| bl fsl_ocram_init |
| #endif |
| |
| mov lr, x29 /* Restore LR */ |
| ret |
| ENDPROC(lowlevel_init) |
| |
| #if defined(CONFIG_FSL_LSCH2) && !defined(CONFIG_SPL_BUILD) |
| ENTRY(fsl_ocram_init) |
| mov x28, lr /* Save LR */ |
| bl fsl_clear_ocram |
| bl fsl_ocram_clear_ecc_err |
| mov lr, x28 /* Restore LR */ |
| ret |
| ENDPROC(fsl_ocram_init) |
| |
| ENTRY(fsl_clear_ocram) |
| /* Clear OCRAM */ |
| ldr x0, =CFG_SYS_FSL_OCRAM_BASE |
| ldr x1, =(CFG_SYS_FSL_OCRAM_BASE + CFG_SYS_FSL_OCRAM_SIZE) |
| mov x2, #0 |
| clear_loop: |
| str x2, [x0] |
| add x0, x0, #8 |
| cmp x0, x1 |
| b.lo clear_loop |
| ret |
| ENDPROC(fsl_clear_ocram) |
| |
| ENTRY(fsl_ocram_clear_ecc_err) |
| /* OCRAM1/2 ECC status bit */ |
| mov w1, #0x60 |
| ldr x0, =DCSR_DCFG_SBEESR2 |
| str w1, [x0] |
| ldr x0, =DCSR_DCFG_MBEESR2 |
| str w1, [x0] |
| ret |
| ENDPROC(fsl_ocram_clear_ecc_err) |
| #endif |
| |
| #ifdef CONFIG_FSL_LSCH3 |
| .globl get_svr |
| get_svr: |
| ldr x1, =FSL_LSCH3_SVR |
| ldr w0, [x1] |
| ret |
| #endif |
| |
| #if defined(CONFIG_SYS_FSL_HAS_CCN504) || defined(CONFIG_SYS_FSL_HAS_CCN508) |
| hnf_pstate_poll: |
| /* x0 has the desired status, return only if operation succeed |
| * clobber x1, x2, x6 |
| */ |
| mov x1, x0 |
| mov w6, #8 /* HN-F node count */ |
| mov x0, #0x18 |
| movk x0, #0x420, lsl #16 /* HNF0_PSTATE_STATUS */ |
| 1: |
| ldr x2, [x0] |
| cmp x2, x1 /* check status */ |
| b.eq 2f |
| b 1b |
| 2: |
| add x0, x0, #0x10000 /* move to next node */ |
| subs w6, w6, #1 |
| cbnz w6, 1b |
| ret |
| |
| hnf_set_pstate: |
| /* x0 has the desired state, clobber x1, x2, x6 */ |
| mov x1, x0 |
| /* power state to SFONLY */ |
| mov w6, #8 /* HN-F node count */ |
| mov x0, #0x10 |
| movk x0, #0x420, lsl #16 /* HNF0_PSTATE_REQ */ |
| 1: /* set pstate to sfonly */ |
| ldr x2, [x0] |
| and x2, x2, #0xfffffffffffffffc /* & HNFPSTAT_MASK */ |
| orr x2, x2, x1 |
| str x2, [x0] |
| add x0, x0, #0x10000 /* move to next node */ |
| subs w6, w6, #1 |
| cbnz w6, 1b |
| |
| ret |
| |
| ENTRY(__asm_flush_l3_dcache) |
| /* |
| * Return status in x0 |
| * success 0 |
| */ |
| mov x29, lr |
| |
| dsb sy |
| mov x0, #0x1 /* HNFPSTAT_SFONLY */ |
| bl hnf_set_pstate |
| |
| mov x0, #0x4 /* SFONLY status */ |
| bl hnf_pstate_poll |
| |
| dsb sy |
| mov x0, #0x3 /* HNFPSTAT_FAM */ |
| bl hnf_set_pstate |
| |
| mov x0, #0xc /* FAM status */ |
| bl hnf_pstate_poll |
| |
| mov x0, #0 |
| mov lr, x29 |
| ret |
| ENDPROC(__asm_flush_l3_dcache) |
| #endif /* CONFIG_SYS_FSL_HAS_CCN504 */ |