include/ns16550.h - filogic/uboot - Gitiles

 /*
  * NS16550 Serial Port
  * originally from linux source (arch/powerpc/boot/ns16550.h)
  *
  * Cleanup and unification
  * (C) 2009 by Detlev Zundel, DENX Software Engineering GmbH
  *
  * modified slightly to
  * have addresses as offsets from CONFIG_SYS_ISA_BASE
  * added a few more definitions
  * added prototypes for ns16550.c
  * reduced no of com ports to 2
  * modifications (c) Rob Taylor, Flying Pig Systems. 2000.
  *
  * added support for port on 64-bit bus
  * by Richard Danter (richard.danter@windriver.com), (C) 2005 Wind River Systems
  */

 /*
  * Note that the following macro magic uses the fact that the compiler
  * will not allocate storage for arrays of size 0
  */

 #include <linux/types.h>

 #ifdef CONFIG_DM_SERIAL
 /*
  * For driver model we always use one byte per register, and sort out the
  * differences in the driver
  */
 #define CONFIG_SYS_NS16550_REG_SIZE (-1)
 #endif

 #ifdef CONFIG_NS16550_DYNAMIC
 #define UART_REG(x)	unsigned char x
 #else
 #if !defined(CONFIG_SYS_NS16550_REG_SIZE) || (CONFIG_SYS_NS16550_REG_SIZE == 0)
 #error "Please define NS16550 registers size."
 #elif defined(CONFIG_SYS_NS16550_MEM32) && !defined(CONFIG_DM_SERIAL)
 #define UART_REG(x) u32 x
 #elif (CONFIG_SYS_NS16550_REG_SIZE > 0)
 #define UART_REG(x)						   \
 	unsigned char prepad_##x[CONFIG_SYS_NS16550_REG_SIZE - 1]; \
 	unsigned char x;
 #elif (CONFIG_SYS_NS16550_REG_SIZE < 0)
 #define UART_REG(x)							\
 	unsigned char x;						\
 	unsigned char postpad_##x[-CONFIG_SYS_NS16550_REG_SIZE - 1];
 #endif
 #endif /* CONFIG_NS16550_DYNAMIC */

 enum ns16550_flags {
 	NS16550_FLAG_IO		= 1 << 0, /* Use I/O access (else mem-mapped) */
 	NS16550_FLAG_ENDIAN	= 1 << 1, /* Use out_le/be_32() */
 	NS16550_FLAG_BE		= 1 << 2, /* Big-endian access (else little) */
 };

 /**
  * struct ns16550_platdata - information about a NS16550 port
  *
  * @base:		Base register address
  * @reg_width:		IO accesses size of registers (in bytes, 1 or 4)
  * @reg_shift:		Shift size of registers (0=byte, 1=16bit, 2=32bit...)
  * @reg_offset:		Offset to start of registers (normally 0)
  * @clock:		UART base clock speed in Hz
  * @fcr:		Offset of FCR register (normally UART_FCR_DEFVAL)
  * @flags:		A few flags (enum ns16550_flags)
  * @bdf:		PCI slot/function (pci_dev_t)
  */
 struct ns16550_platdata {
 	unsigned long base;
 	int reg_width;
 	int reg_shift;
 	int reg_offset;
 	int clock;
 	u32 fcr;
 	int flags;
 #if defined(CONFIG_PCI) && defined(CONFIG_SPL)
 	int bdf;
 #endif
 };

 struct udevice;

 struct NS16550 {
 	UART_REG(rbr);		/* 0 */
 	UART_REG(ier);		/* 1 */
 	UART_REG(fcr);		/* 2 */
 	UART_REG(lcr);		/* 3 */
 	UART_REG(mcr);		/* 4 */
 	UART_REG(lsr);		/* 5 */
 	UART_REG(msr);		/* 6 */
 	UART_REG(spr);		/* 7 */
 #ifdef CONFIG_SOC_DA8XX
 	UART_REG(reg8);		/* 8 */
 	UART_REG(reg9);		/* 9 */
 	UART_REG(revid1);	/* A */
 	UART_REG(revid2);	/* B */
 	UART_REG(pwr_mgmt);	/* C */
 	UART_REG(mdr1);		/* D */
 #else
 	UART_REG(mdr1);		/* 8 */
 	UART_REG(reg9);		/* 9 */
 	UART_REG(regA);		/* A */
 	UART_REG(regB);		/* B */
 	UART_REG(regC);		/* C */
 	UART_REG(regD);		/* D */
 	UART_REG(regE);		/* E */
 	UART_REG(uasr);		/* F */
 	UART_REG(scr);		/* 10*/
 	UART_REG(ssr);		/* 11*/
 #endif
 #ifdef CONFIG_DM_SERIAL
 	struct ns16550_platdata *plat;
 #endif
 };

 #define thr rbr
 #define iir fcr
 #define dll rbr
 #define dlm ier

 typedef struct NS16550 *NS16550_t;

 /*
  * These are the definitions for the FIFO Control Register
  */
 #define UART_FCR_FIFO_EN	0x01 /* Fifo enable */
 #define UART_FCR_CLEAR_RCVR	0x02 /* Clear the RCVR FIFO */
 #define UART_FCR_CLEAR_XMIT	0x04 /* Clear the XMIT FIFO */
 #define UART_FCR_DMA_SELECT	0x08 /* For DMA applications */
 #define UART_FCR_TRIGGER_MASK	0xC0 /* Mask for the FIFO trigger range */
 #define UART_FCR_TRIGGER_1	0x00 /* Mask for trigger set at 1 */
 #define UART_FCR_TRIGGER_4	0x40 /* Mask for trigger set at 4 */
 #define UART_FCR_TRIGGER_8	0x80 /* Mask for trigger set at 8 */
 #define UART_FCR_TRIGGER_14	0xC0 /* Mask for trigger set at 14 */

 #define UART_FCR_RXSR		0x02 /* Receiver soft reset */
 #define UART_FCR_TXSR		0x04 /* Transmitter soft reset */

 /* Ingenic JZ47xx specific UART-enable bit. */
 #define UART_FCR_UME		0x10

 /* Clear & enable FIFOs */
 #define UART_FCR_DEFVAL (UART_FCR_FIFO_EN | \
 			UART_FCR_RXSR |	\
 			UART_FCR_TXSR)

 /*
  * These are the definitions for the Modem Control Register
  */
 #define UART_MCR_DTR	0x01		/* DTR   */
 #define UART_MCR_RTS	0x02		/* RTS   */
 #define UART_MCR_OUT1	0x04		/* Out 1 */
 #define UART_MCR_OUT2	0x08		/* Out 2 */
 #define UART_MCR_LOOP	0x10		/* Enable loopback test mode */
 #define UART_MCR_AFE	0x20		/* Enable auto-RTS/CTS */

 #define UART_MCR_DMA_EN	0x04
 #define UART_MCR_TX_DFR	0x08

 /*
  * These are the definitions for the Line Control Register
  *
  * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
  * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
  */
 #define UART_LCR_WLS_MSK 0x03		/* character length select mask */
 #define UART_LCR_WLS_5	0x00		/* 5 bit character length */
 #define UART_LCR_WLS_6	0x01		/* 6 bit character length */
 #define UART_LCR_WLS_7	0x02		/* 7 bit character length */
 #define UART_LCR_WLS_8	0x03		/* 8 bit character length */
 #define UART_LCR_STB	0x04		/* # stop Bits, off=1, on=1.5 or 2) */
 #define UART_LCR_PEN	0x08		/* Parity eneble */
 #define UART_LCR_EPS	0x10		/* Even Parity Select */
 #define UART_LCR_STKP	0x20		/* Stick Parity */
 #define UART_LCR_SBRK	0x40		/* Set Break */
 #define UART_LCR_BKSE	0x80		/* Bank select enable */
 #define UART_LCR_DLAB	0x80		/* Divisor latch access bit */

 /*
  * These are the definitions for the Line Status Register
  */
 #define UART_LSR_DR	0x01		/* Data ready */
 #define UART_LSR_OE	0x02		/* Overrun */
 #define UART_LSR_PE	0x04		/* Parity error */
 #define UART_LSR_FE	0x08		/* Framing error */
 #define UART_LSR_BI	0x10		/* Break */
 #define UART_LSR_THRE	0x20		/* Xmit holding register empty */
 #define UART_LSR_TEMT	0x40		/* Xmitter empty */
 #define UART_LSR_ERR	0x80		/* Error */

 #define UART_MSR_DCD	0x80		/* Data Carrier Detect */
 #define UART_MSR_RI	0x40		/* Ring Indicator */
 #define UART_MSR_DSR	0x20		/* Data Set Ready */
 #define UART_MSR_CTS	0x10		/* Clear to Send */
 #define UART_MSR_DDCD	0x08		/* Delta DCD */
 #define UART_MSR_TERI	0x04		/* Trailing edge ring indicator */
 #define UART_MSR_DDSR	0x02		/* Delta DSR */
 #define UART_MSR_DCTS	0x01		/* Delta CTS */

 /*
  * These are the definitions for the Interrupt Identification Register
  */
 #define UART_IIR_NO_INT	0x01	/* No interrupts pending */
 #define UART_IIR_ID	0x06	/* Mask for the interrupt ID */

 #define UART_IIR_MSI	0x00	/* Modem status interrupt */
 #define UART_IIR_THRI	0x02	/* Transmitter holding register empty */
 #define UART_IIR_RDI	0x04	/* Receiver data interrupt */
 #define UART_IIR_RLSI	0x06	/* Receiver line status interrupt */

 /*
  * These are the definitions for the Interrupt Enable Register
  */
 #define UART_IER_MSI	0x08	/* Enable Modem status interrupt */
 #define UART_IER_RLSI	0x04	/* Enable receiver line status interrupt */
 #define UART_IER_THRI	0x02	/* Enable Transmitter holding register int. */
 #define UART_IER_RDI	0x01	/* Enable receiver data interrupt */

 /* useful defaults for LCR */
 #define UART_LCR_8N1	0x03

 void NS16550_init(NS16550_t com_port, int baud_divisor);
 void NS16550_putc(NS16550_t com_port, char c);
 char NS16550_getc(NS16550_t com_port);
 int NS16550_tstc(NS16550_t com_port);
 void NS16550_reinit(NS16550_t com_port, int baud_divisor);

 /**
  * ns16550_calc_divisor() - calculate the divisor given clock and baud rate
  *
  * Given the UART input clock and required baudrate, calculate the divisor
  * that should be used.
  *
  * @port:	UART port
  * @clock:	UART input clock speed in Hz
  * @baudrate:	Required baud rate
  * @return baud rate divisor that should be used
  */
 int ns16550_calc_divisor(NS16550_t port, int clock, int baudrate);

 /**
  * ns16550_serial_of_to_plat() - convert DT to platform data
  *
  * Decode a device tree node for an ns16550 device. This includes the
  * register base address and register shift properties. The caller must set
  * up the clock frequency.
  *
  * @dev:	dev to decode platform data for
  * @return:	0 if OK, -EINVAL on error
  */
 int ns16550_serial_of_to_plat(struct udevice *dev);

 /**
  * ns16550_serial_probe() - probe a serial port
  *
  * This sets up the serial port ready for use, except for the baud rate
  * @return 0, or -ve on error
  */
 int ns16550_serial_probe(struct udevice *dev);

 /**
  * struct ns16550_serial_ops - ns16550 serial operations
  *
  * These should be used by the client driver for the driver's 'ops' member
  */
 extern const struct dm_serial_ops ns16550_serial_ops;
	/*
	* NS16550 Serial Port
	* originally from linux source (arch/powerpc/boot/ns16550.h)
	*
	* Cleanup and unification
	* (C) 2009 by Detlev Zundel, DENX Software Engineering GmbH
	*
	* modified slightly to
	* have addresses as offsets from CONFIG_SYS_ISA_BASE
	* added a few more definitions
	* added prototypes for ns16550.c
	* reduced no of com ports to 2
	* modifications (c) Rob Taylor, Flying Pig Systems. 2000.
	*
	* added support for port on 64-bit bus
	* by Richard Danter (richard.danter@windriver.com), (C) 2005 Wind River Systems
	*/

	/*
	* Note that the following macro magic uses the fact that the compiler
	* will not allocate storage for arrays of size 0
	*/

	#include <linux/types.h>

	#ifdef CONFIG_DM_SERIAL
	/*
	* For driver model we always use one byte per register, and sort out the
	* differences in the driver
	*/
	#define CONFIG_SYS_NS16550_REG_SIZE (-1)
	#endif

	#ifdef CONFIG_NS16550_DYNAMIC
	#define UART_REG(x) unsigned char x
	#else
	#if !defined(CONFIG_SYS_NS16550_REG_SIZE) \|\| (CONFIG_SYS_NS16550_REG_SIZE == 0)
	#error "Please define NS16550 registers size."
	#elif defined(CONFIG_SYS_NS16550_MEM32) && !defined(CONFIG_DM_SERIAL)
	#define UART_REG(x) u32 x
	#elif (CONFIG_SYS_NS16550_REG_SIZE > 0)
	#define UART_REG(x) \
	unsigned char prepad_##x[CONFIG_SYS_NS16550_REG_SIZE - 1]; \
	unsigned char x;
	#elif (CONFIG_SYS_NS16550_REG_SIZE < 0)
	#define UART_REG(x) \
	unsigned char x; \
	unsigned char postpad_##x[-CONFIG_SYS_NS16550_REG_SIZE - 1];
	#endif
	#endif /* CONFIG_NS16550_DYNAMIC */

	enum ns16550_flags {
	NS16550_FLAG_IO = 1 << 0, /* Use I/O access (else mem-mapped) */
	NS16550_FLAG_ENDIAN = 1 << 1, /* Use out_le/be_32() */
	NS16550_FLAG_BE = 1 << 2, /* Big-endian access (else little) */
	};

	/**
	* struct ns16550_platdata - information about a NS16550 port
	*
	* @base: Base register address
	* @reg_width: IO accesses size of registers (in bytes, 1 or 4)
	* @reg_shift: Shift size of registers (0=byte, 1=16bit, 2=32bit...)
	* @reg_offset: Offset to start of registers (normally 0)
	* @clock: UART base clock speed in Hz
	* @fcr: Offset of FCR register (normally UART_FCR_DEFVAL)
	* @flags: A few flags (enum ns16550_flags)
	* @bdf: PCI slot/function (pci_dev_t)
	*/
	struct ns16550_platdata {
	unsigned long base;
	int reg_width;
	int reg_shift;
	int reg_offset;
	int clock;
	u32 fcr;
	int flags;
	#if defined(CONFIG_PCI) && defined(CONFIG_SPL)
	int bdf;
	#endif
	};

	struct udevice;

	struct NS16550 {
	UART_REG(rbr); /* 0 */
	UART_REG(ier); /* 1 */
	UART_REG(fcr); /* 2 */
	UART_REG(lcr); /* 3 */
	UART_REG(mcr); /* 4 */
	UART_REG(lsr); /* 5 */
	UART_REG(msr); /* 6 */
	UART_REG(spr); /* 7 */
	#ifdef CONFIG_SOC_DA8XX
	UART_REG(reg8); /* 8 */
	UART_REG(reg9); /* 9 */
	UART_REG(revid1); /* A */
	UART_REG(revid2); /* B */
	UART_REG(pwr_mgmt); /* C */
	UART_REG(mdr1); /* D */
	#else
	UART_REG(mdr1); /* 8 */
	UART_REG(reg9); /* 9 */
	UART_REG(regA); /* A */
	UART_REG(regB); /* B */
	UART_REG(regC); /* C */
	UART_REG(regD); /* D */
	UART_REG(regE); /* E */
	UART_REG(uasr); /* F */
	UART_REG(scr); /* 10*/
	UART_REG(ssr); /* 11*/
	#endif
	#ifdef CONFIG_DM_SERIAL
	struct ns16550_platdata *plat;
	#endif
	};

	#define thr rbr
	#define iir fcr
	#define dll rbr
	#define dlm ier

	typedef struct NS16550 *NS16550_t;

	/*
	* These are the definitions for the FIFO Control Register
	*/
	#define UART_FCR_FIFO_EN 0x01 /* Fifo enable */
	#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */
	#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */
	#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */
	#define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */
	#define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */
	#define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */
	#define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */
	#define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */

	#define UART_FCR_RXSR 0x02 /* Receiver soft reset */
	#define UART_FCR_TXSR 0x04 /* Transmitter soft reset */

	/* Ingenic JZ47xx specific UART-enable bit. */
	#define UART_FCR_UME 0x10

	/* Clear & enable FIFOs */
	#define UART_FCR_DEFVAL (UART_FCR_FIFO_EN \| \
	UART_FCR_RXSR \| \
	UART_FCR_TXSR)

	/*
	* These are the definitions for the Modem Control Register
	*/
	#define UART_MCR_DTR 0x01 /* DTR */
	#define UART_MCR_RTS 0x02 /* RTS */
	#define UART_MCR_OUT1 0x04 /* Out 1 */
	#define UART_MCR_OUT2 0x08 /* Out 2 */
	#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */
	#define UART_MCR_AFE 0x20 /* Enable auto-RTS/CTS */

	#define UART_MCR_DMA_EN 0x04
	#define UART_MCR_TX_DFR 0x08

	/*
	* These are the definitions for the Line Control Register
	*
	* Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
	* UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
	*/
	#define UART_LCR_WLS_MSK 0x03 /* character length select mask */
	#define UART_LCR_WLS_5 0x00 /* 5 bit character length */
	#define UART_LCR_WLS_6 0x01 /* 6 bit character length */
	#define UART_LCR_WLS_7 0x02 /* 7 bit character length */
	#define UART_LCR_WLS_8 0x03 /* 8 bit character length */
	#define UART_LCR_STB 0x04 /* # stop Bits, off=1, on=1.5 or 2) */
	#define UART_LCR_PEN 0x08 /* Parity eneble */
	#define UART_LCR_EPS 0x10 /* Even Parity Select */
	#define UART_LCR_STKP 0x20 /* Stick Parity */
	#define UART_LCR_SBRK 0x40 /* Set Break */
	#define UART_LCR_BKSE 0x80 /* Bank select enable */
	#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */

	/*
	* These are the definitions for the Line Status Register
	*/
	#define UART_LSR_DR 0x01 /* Data ready */
	#define UART_LSR_OE 0x02 /* Overrun */
	#define UART_LSR_PE 0x04 /* Parity error */
	#define UART_LSR_FE 0x08 /* Framing error */
	#define UART_LSR_BI 0x10 /* Break */
	#define UART_LSR_THRE 0x20 /* Xmit holding register empty */
	#define UART_LSR_TEMT 0x40 /* Xmitter empty */
	#define UART_LSR_ERR 0x80 /* Error */

	#define UART_MSR_DCD 0x80 /* Data Carrier Detect */
	#define UART_MSR_RI 0x40 /* Ring Indicator */
	#define UART_MSR_DSR 0x20 /* Data Set Ready */
	#define UART_MSR_CTS 0x10 /* Clear to Send */
	#define UART_MSR_DDCD 0x08 /* Delta DCD */
	#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */
	#define UART_MSR_DDSR 0x02 /* Delta DSR */
	#define UART_MSR_DCTS 0x01 /* Delta CTS */

	/*
	* These are the definitions for the Interrupt Identification Register
	*/
	#define UART_IIR_NO_INT 0x01 /* No interrupts pending */
	#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */

	#define UART_IIR_MSI 0x00 /* Modem status interrupt */
	#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */
	#define UART_IIR_RDI 0x04 /* Receiver data interrupt */
	#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */

	/*
	* These are the definitions for the Interrupt Enable Register
	*/
	#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */
	#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */
	#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */
	#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */

	/* useful defaults for LCR */
	#define UART_LCR_8N1 0x03

	void NS16550_init(NS16550_t com_port, int baud_divisor);
	void NS16550_putc(NS16550_t com_port, char c);
	char NS16550_getc(NS16550_t com_port);
	int NS16550_tstc(NS16550_t com_port);
	void NS16550_reinit(NS16550_t com_port, int baud_divisor);

	/**
	* ns16550_calc_divisor() - calculate the divisor given clock and baud rate
	*
	* Given the UART input clock and required baudrate, calculate the divisor
	* that should be used.
	*
	* @port: UART port
	* @clock: UART input clock speed in Hz
	* @baudrate: Required baud rate
	* @return baud rate divisor that should be used
	*/
	int ns16550_calc_divisor(NS16550_t port, int clock, int baudrate);

	/**
	* ns16550_serial_of_to_plat() - convert DT to platform data
	*
	* Decode a device tree node for an ns16550 device. This includes the
	* register base address and register shift properties. The caller must set
	* up the clock frequency.
	*
	* @dev: dev to decode platform data for
	* @return: 0 if OK, -EINVAL on error
	*/
	int ns16550_serial_of_to_plat(struct udevice *dev);

	/**
	* ns16550_serial_probe() - probe a serial port
	*
	* This sets up the serial port ready for use, except for the baud rate
	* @return 0, or -ve on error
	*/
	int ns16550_serial_probe(struct udevice *dev);

	/**
	* struct ns16550_serial_ops - ns16550 serial operations
	*
	* These should be used by the client driver for the driver's 'ops' member
	*/
	extern const struct dm_serial_ops ns16550_serial_ops;