board/cloudengines/pogo_e02/pogo_e02.c

// SPDX-License-Identifier: GPL-2.0+
/*
 * Copyright (C) 2012
 * David Purdy <david.c.purdy@gmail.com>
 *
 * Based on Kirkwood support:
 * (C) Copyright 2009
 * Marvell Semiconductor <www.marvell.com>
 * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
 */

#include <common.h>
#include <init.h>
#include <log.h>
#include <miiphy.h>
#include <net.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
#include <asm/arch/mpp.h>
#include "pogo_e02.h"

DECLARE_GLOBAL_DATA_PTR;

int board_early_init_f(void)
{
	/*
	 * default gpio configuration
	 * There are maximum 64 gpios controlled through 2 sets of registers
	 * the  below configuration configures mainly initial LED status
	 */
	mvebu_config_gpio(POGO_E02_OE_VAL_LOW,
			  POGO_E02_OE_VAL_HIGH,
			  POGO_E02_OE_LOW, POGO_E02_OE_HIGH);

	/* Multi-Purpose Pins Functionality configuration */
	static const u32 kwmpp_config[] = {
		MPP0_NF_IO2,
		MPP1_NF_IO3,
		MPP2_NF_IO4,
		MPP3_NF_IO5,
		MPP4_NF_IO6,
		MPP5_NF_IO7,
		MPP6_SYSRST_OUTn,
		MPP7_GPO,
		MPP8_UART0_RTS,
		MPP9_UART0_CTS,
		MPP10_UART0_TXD,
		MPP11_UART0_RXD,
		MPP12_SD_CLK,
		MPP13_SD_CMD,
		MPP14_SD_D0,
		MPP15_SD_D1,
		MPP16_SD_D2,
		MPP17_SD_D3,
		MPP18_NF_IO0,
		MPP19_NF_IO1,
		MPP29_TSMP9,	/* USB Power Enable */
		MPP48_GPIO,	/* LED green */
		MPP49_GPIO,	/* LED orange */
		0
	};
	kirkwood_mpp_conf(kwmpp_config, NULL);
	return 0;
}

int board_init(void)
{
	/* Boot parameters address */
	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;

	return 0;
}

#ifdef CONFIG_RESET_PHY_R
/* Configure and initialize PHY */
void reset_phy(void)
{
	u16 reg;
	u16 devadr;
	char *name = "egiga0";

	if (miiphy_set_current_dev(name))
		return;

	/* command to read PHY dev address */
	if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
		printf("Err..(%s) could not read PHY dev address\n", __func__);
		return;
	}

	/*
	 * Enable RGMII delay on Tx and Rx for CPU port
	 * Ref: sec 4.7.2 of chip datasheet
	 */
	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
	miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg);
	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
	miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);

	/* reset the phy */
	miiphy_reset(name, devadr);

	debug("88E1116 Initialized on %s\n", name);
}
#endif /* CONFIG_RESET_PHY_R */