| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Machine Specific Values for SMDK5250 board based on EXYNOS5 |
| * |
| * Copyright (C) 2012 Samsung Electronics |
| */ |
| |
| #ifndef _SMDK5250_SETUP_H |
| #define _SMDK5250_SETUP_H |
| |
| #include <linux/types.h> |
| #include <asm/arch/dmc.h> |
| |
| #define NOT_AVAILABLE 0 |
| #define DATA_MASK 0xFFFFF |
| |
| #define ENABLE_BIT 0x1 |
| #define DISABLE_BIT 0x0 |
| #define CA_SWAP_EN (1 << 0) |
| |
| /* Set PLL */ |
| #define set_pll(mdiv, pdiv, sdiv) (1<<31 | mdiv<<16 | pdiv<<8 | sdiv) |
| |
| /* MEMCONTROL register bit fields */ |
| #define DMC_MEMCONTROL_CLK_STOP_DISABLE (0 << 0) |
| #define DMC_MEMCONTROL_DPWRDN_DISABLE (0 << 1) |
| #define DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE (0 << 2) |
| #define DMC_MEMCONTROL_TP_DISABLE (0 << 4) |
| #define DMC_MEMCONTROL_DSREF_DISABLE (0 << 5) |
| #define DMC_MEMCONTROL_DSREF_ENABLE (1 << 5) |
| #define DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(x) (x << 6) |
| |
| #define DMC_MEMCONTROL_MEM_TYPE_LPDDR3 (7 << 8) |
| #define DMC_MEMCONTROL_MEM_TYPE_DDR3 (6 << 8) |
| #define DMC_MEMCONTROL_MEM_TYPE_LPDDR2 (5 << 8) |
| |
| #define DMC_MEMCONTROL_MEM_WIDTH_32BIT (2 << 12) |
| |
| #define DMC_MEMCONTROL_NUM_CHIP_1 (0 << 16) |
| #define DMC_MEMCONTROL_NUM_CHIP_2 (1 << 16) |
| |
| #define DMC_MEMCONTROL_BL_8 (3 << 20) |
| #define DMC_MEMCONTROL_BL_4 (2 << 20) |
| |
| #define DMC_MEMCONTROL_PZQ_DISABLE (0 << 24) |
| |
| #define DMC_MEMCONTROL_MRR_BYTE_7_0 (0 << 25) |
| #define DMC_MEMCONTROL_MRR_BYTE_15_8 (1 << 25) |
| #define DMC_MEMCONTROL_MRR_BYTE_23_16 (2 << 25) |
| #define DMC_MEMCONTROL_MRR_BYTE_31_24 (3 << 25) |
| |
| /* MEMCONFIG0 register bit fields */ |
| #define DMC_MEMCONFIGX_CHIP_MAP_INTERLEAVED (1 << 12) |
| #define DMC_MEMCONFIG_CHIP_MAP_SPLIT (2 << 12) |
| #define DMC_MEMCONFIGX_CHIP_COL_10 (3 << 8) |
| #define DMC_MEMCONFIGX_CHIP_ROW_14 (2 << 4) |
| #define DMC_MEMCONFIGX_CHIP_ROW_15 (3 << 4) |
| #define DMC_MEMCONFIGX_CHIP_BANK_8 (3 << 0) |
| |
| #define DMC_MEMBASECONFIGX_CHIP_BASE(x) (x << 16) |
| #define DMC_MEMBASECONFIGX_CHIP_MASK(x) (x << 0) |
| #define DMC_MEMBASECONFIG_VAL(x) ( \ |
| DMC_MEMBASECONFIGX_CHIP_BASE(x) | \ |
| DMC_MEMBASECONFIGX_CHIP_MASK(0x780) \ |
| ) |
| |
| /* |
| * As we use channel interleaving, therefore value of the base address |
| * register must be set as half of the bus base address |
| * RAM start addess is 0x2000_0000 which means chip_base is 0x20, so |
| * we need to set half 0x10 to the membaseconfigx registers |
| * see exynos5420 UM section 17.17.3.21 for more. |
| */ |
| #define DMC_CHIP_BASE_0 0x10 |
| #define DMC_CHIP_BASE_1 0x50 |
| #define DMC_CHIP_MASK 0x7C0 |
| |
| #define DMC_MEMBASECONFIG0_VAL DMC_MEMBASECONFIG_VAL(0x40) |
| #define DMC_MEMBASECONFIG1_VAL DMC_MEMBASECONFIG_VAL(0x80) |
| |
| #define DMC_PRECHCONFIG_VAL 0xFF000000 |
| #define DMC_PWRDNCONFIG_VAL 0xFFFF00FF |
| |
| #define DMC_CONCONTROL_RESET_VAL 0x0FFF0000 |
| #define DFI_INIT_START (1 << 28) |
| #define EMPTY (1 << 8) |
| #define AREF_EN (1 << 5) |
| |
| #define DFI_INIT_COMPLETE_CHO (1 << 2) |
| #define DFI_INIT_COMPLETE_CH1 (1 << 3) |
| |
| #define RDLVL_COMPLETE_CHO (1 << 14) |
| #define RDLVL_COMPLETE_CH1 (1 << 15) |
| |
| #define CLK_STOP_EN (1 << 0) |
| #define DPWRDN_EN (1 << 1) |
| #define DSREF_EN (1 << 5) |
| |
| /* COJCONTROL register bit fields */ |
| #define DMC_CONCONTROL_IO_PD_CON_DISABLE (0 << 3) |
| #define DMC_CONCONTROL_IO_PD_CON_ENABLE (1 << 3) |
| #define DMC_CONCONTROL_AREF_EN_DISABLE (0 << 5) |
| #define DMC_CONCONTROL_AREF_EN_ENABLE (1 << 5) |
| #define DMC_CONCONTROL_EMPTY_DISABLE (0 << 8) |
| #define DMC_CONCONTROL_EMPTY_ENABLE (1 << 8) |
| #define DMC_CONCONTROL_RD_FETCH_DISABLE (0x0 << 12) |
| #define DMC_CONCONTROL_TIMEOUT_LEVEL0 (0xFFF << 16) |
| #define DMC_CONCONTROL_DFI_INIT_START_DISABLE (0 << 28) |
| |
| #define DMC_CONCONTROL_VAL 0x1FFF2101 |
| |
| #define DREX_CONCONTROL_VAL DMC_CONCONTROL_VAL \ |
| | DMC_CONCONTROL_AREF_EN_ENABLE \ |
| | DMC_CONCONTROL_IO_PD_CON_ENABLE |
| |
| #define DMC_CONCONTROL_IO_PD_CON(x) (x << 6) |
| |
| /* CLK_DIV_CPU1 */ |
| #define HPM_RATIO 0x2 |
| #define COPY_RATIO 0x0 |
| |
| /* CLK_DIV_CPU1 = 0x00000003 */ |
| #define CLK_DIV_CPU1_VAL ((HPM_RATIO << 4) \ |
| | (COPY_RATIO)) |
| |
| /* CLK_SRC_CORE0 */ |
| #define CLK_SRC_CORE0_VAL 0x00000000 |
| |
| /* CLK_SRC_CORE1 */ |
| #define CLK_SRC_CORE1_VAL 0x100 |
| |
| /* CLK_DIV_CORE0 */ |
| #define CLK_DIV_CORE0_VAL 0x00120000 |
| |
| /* CLK_DIV_CORE1 */ |
| #define CLK_DIV_CORE1_VAL 0x07070700 |
| |
| /* CLK_DIV_SYSRGT */ |
| #define CLK_DIV_SYSRGT_VAL 0x00000111 |
| |
| /* CLK_DIV_ACP */ |
| #define CLK_DIV_ACP_VAL 0x12 |
| |
| /* CLK_DIV_SYSLFT */ |
| #define CLK_DIV_SYSLFT_VAL 0x00000311 |
| |
| #define MUX_APLL_SEL_MASK (1 << 0) |
| #define MUX_MPLL_SEL_MASK (1 << 8) |
| #define MPLL_SEL_MOUT_MPLLFOUT (2 << 8) |
| #define MUX_CPLL_SEL_MASK (1 << 8) |
| #define MUX_EPLL_SEL_MASK (1 << 12) |
| #define MUX_VPLL_SEL_MASK (1 << 16) |
| #define MUX_GPLL_SEL_MASK (1 << 28) |
| #define MUX_BPLL_SEL_MASK (1 << 0) |
| #define MUX_HPM_SEL_MASK (1 << 20) |
| #define HPM_SEL_SCLK_MPLL (1 << 21) |
| #define PLL_LOCKED (1 << 29) |
| #define APLL_CON0_LOCKED (1 << 29) |
| #define MPLL_CON0_LOCKED (1 << 29) |
| #define BPLL_CON0_LOCKED (1 << 29) |
| #define CPLL_CON0_LOCKED (1 << 29) |
| #define EPLL_CON0_LOCKED (1 << 29) |
| #define GPLL_CON0_LOCKED (1 << 29) |
| #define VPLL_CON0_LOCKED (1 << 29) |
| #define CLK_REG_DISABLE 0x0 |
| #define TOP2_VAL 0x0110000 |
| |
| /* SCLK_SRC_ISP - set SPI0/1 to 6 = SCLK_MPLL_USER */ |
| #define SPI0_ISP_SEL 6 |
| #define SPI1_ISP_SEL 6 |
| #define SCLK_SRC_ISP_VAL (SPI1_ISP_SEL << 4) \ |
| | (SPI0_ISP_SEL << 0) |
| |
| /* SCLK_DIV_ISP - set SPI0/1 to 0xf = divide by 16 */ |
| #define SPI0_ISP_RATIO 0xf |
| #define SPI1_ISP_RATIO 0xf |
| #define SCLK_DIV_ISP_VAL (SPI1_ISP_RATIO << 12) \ |
| | (SPI0_ISP_RATIO << 0) |
| |
| /* CLK_DIV_FSYS2 */ |
| #define MMC2_RATIO_MASK 0xf |
| #define MMC2_RATIO_VAL 0x3 |
| #define MMC2_RATIO_OFFSET 0 |
| |
| #define MMC2_PRE_RATIO_MASK 0xff |
| #define MMC2_PRE_RATIO_VAL 0x9 |
| #define MMC2_PRE_RATIO_OFFSET 8 |
| |
| #define MMC3_RATIO_MASK 0xf |
| #define MMC3_RATIO_VAL 0x1 |
| #define MMC3_RATIO_OFFSET 16 |
| |
| #define MMC3_PRE_RATIO_MASK 0xff |
| #define MMC3_PRE_RATIO_VAL 0x0 |
| #define MMC3_PRE_RATIO_OFFSET 24 |
| |
| /* CLK_SRC_LEX */ |
| #define CLK_SRC_LEX_VAL 0x0 |
| |
| /* CLK_DIV_LEX */ |
| #define CLK_DIV_LEX_VAL 0x10 |
| |
| /* CLK_DIV_R0X */ |
| #define CLK_DIV_R0X_VAL 0x10 |
| |
| /* CLK_DIV_L0X */ |
| #define CLK_DIV_R1X_VAL 0x10 |
| |
| /* CLK_DIV_ISP2 */ |
| #define CLK_DIV_ISP2_VAL 0x1 |
| |
| /* CLK_SRC_KFC */ |
| #define SRC_KFC_HPM_SEL (1 << 15) |
| |
| /* CLK_SRC_KFC */ |
| #define CLK_SRC_KFC_VAL 0x00008001 |
| |
| /* CLK_DIV_KFC */ |
| #define CLK_DIV_KFC_VAL 0x03300110 |
| |
| /* CLK_DIV2_RATIO */ |
| #define CLK_DIV2_RATIO 0x10111150 |
| |
| /* CLK_DIV4_RATIO */ |
| #define CLK_DIV4_RATIO 0x00000003 |
| |
| /* CLK_DIV_G2D */ |
| #define CLK_DIV_G2D 0x00000010 |
| |
| /* |
| * DIV_DISP1_0 |
| * For DP, divisor should be 2 |
| */ |
| #define CLK_DIV_DISP1_0_FIMD1 (2 << 0) |
| |
| /* CLK_GATE_IP_DISP1 */ |
| #define CLK_GATE_DP1_ALLOW (1 << 4) |
| |
| /* AUDIO CLK SEL */ |
| #define AUDIO0_SEL_EPLL (0x6 << 28) |
| #define AUDIO0_RATIO 0x5 |
| #define PCM0_RATIO 0x3 |
| #define DIV_MAU_VAL (PCM0_RATIO << 24 | AUDIO0_RATIO << 20) |
| |
| /* CLK_SRC_CDREX */ |
| #define MUX_MCLK_CDR_MSPLL (1 << 4) |
| #define MUX_BPLL_SEL_FOUTBPLL (1 << 0) |
| #define BPLL_SEL_MASK 0x7 |
| #define FOUTBPLL 2 |
| |
| #define DDR3PHY_CTRL_PHY_RESET (1 << 0) |
| #define DDR3PHY_CTRL_PHY_RESET_OFF (0 << 0) |
| |
| #define PHY_CON0_RESET_VAL 0x17020a40 |
| #define P0_CMD_EN (1 << 14) |
| #define BYTE_RDLVL_EN (1 << 13) |
| #define CTRL_SHGATE (1 << 8) |
| |
| #define PHY_CON1_RESET_VAL 0x09210100 |
| #define RDLVL_PASS_ADJ_VAL 0x6 |
| #define RDLVL_PASS_ADJ_OFFSET 16 |
| #define CTRL_GATEDURADJ_MASK (0xf << 20) |
| #define READ_LEVELLING_DDR3 0x0100 |
| |
| #define PHY_CON2_RESET_VAL 0x00010004 |
| #define INIT_DESKEW_EN (1 << 6) |
| #define DLL_DESKEW_EN (1 << 12) |
| #define RDLVL_GATE_EN (1 << 24) |
| #define RDLVL_EN (1 << 25) |
| #define RDLVL_INCR_ADJ (0x1 << 16) |
| |
| /* DREX_PAUSE */ |
| #define DREX_PAUSE_EN (1 << 0) |
| |
| #define BYPASS_EN (1 << 22) |
| |
| /* MEMMORY VAL */ |
| #define PHY_CON0_VAL 0x17021A00 |
| |
| #define PHY_CON12_RESET_VAL 0x10100070 |
| #define PHY_CON12_VAL 0x10107F50 |
| #define CTRL_START (1 << 6) |
| #define CTRL_DLL_ON (1 << 5) |
| #define CTRL_LOCK_COARSE_OFFSET 10 |
| #define CTRL_LOCK_COARSE_MASK (0x7F << CTRL_LOCK_COARSE_OFFSET) |
| #define CTRL_LOCK_COARSE(x) (((x) & CTRL_LOCK_COARSE_MASK) >> \ |
| CTRL_LOCK_COARSE_OFFSET) |
| #define CTRL_FORCE_MASK (0x7F << 8) |
| #define CTRL_FINE_LOCKED 0x7 |
| |
| #define CTRL_OFFSETD_RESET_VAL 0x8 |
| #define CTRL_OFFSETD_VAL 0x7F |
| |
| #define CTRL_OFFSETR0 0x7F |
| #define CTRL_OFFSETR1 0x7F |
| #define CTRL_OFFSETR2 0x7F |
| #define CTRL_OFFSETR3 0x7F |
| #define PHY_CON4_VAL (CTRL_OFFSETR0 << 0 | \ |
| CTRL_OFFSETR1 << 8 | \ |
| CTRL_OFFSETR2 << 16 | \ |
| CTRL_OFFSETR3 << 24) |
| #define PHY_CON4_RESET_VAL 0x08080808 |
| |
| #define CTRL_OFFSETW0 0x7F |
| #define CTRL_OFFSETW1 0x7F |
| #define CTRL_OFFSETW2 0x7F |
| #define CTRL_OFFSETW3 0x7F |
| #define PHY_CON6_VAL (CTRL_OFFSETW0 << 0 | \ |
| CTRL_OFFSETW1 << 8 | \ |
| CTRL_OFFSETW2 << 16 | \ |
| CTRL_OFFSETW3 << 24) |
| #define PHY_CON6_RESET_VAL 0x08080808 |
| |
| #define PHY_CON14_RESET_VAL 0x001F0000 |
| #define CTRL_PULLD_DQS 0xF |
| #define CTRL_PULLD_DQS_OFFSET 0 |
| |
| /* ZQ Configurations */ |
| #define PHY_CON16_RESET_VAL 0x08000304 |
| |
| #define ZQ_CLK_EN (1 << 27) |
| #define ZQ_CLK_DIV_EN (1 << 18) |
| #define ZQ_MANUAL_STR (1 << 1) |
| #define ZQ_DONE (1 << 0) |
| #define ZQ_MODE_DDS_OFFSET 24 |
| |
| #define CTRL_RDLVL_GATE_ENABLE 1 |
| #define CTRL_RDLVL_GATE_DISABLE 0 |
| #define CTRL_RDLVL_DATA_ENABLE 2 |
| |
| /* Direct Command */ |
| #define DIRECT_CMD_NOP 0x07000000 |
| #define DIRECT_CMD_PALL 0x01000000 |
| #define DIRECT_CMD_ZQINIT 0x0a000000 |
| #define DIRECT_CMD_CHANNEL_SHIFT 28 |
| #define DIRECT_CMD_CHIP_SHIFT 20 |
| #define DIRECT_CMD_BANK_SHIFT 16 |
| #define DIRECT_CMD_REFA (5 << 24) |
| #define DIRECT_CMD_MRS1 0x71C00 |
| #define DIRECT_CMD_MRS2 0x10BFC |
| #define DIRECT_CMD_MRS3 0x0050C |
| #define DIRECT_CMD_MRS4 0x00868 |
| #define DIRECT_CMD_MRS5 0x00C04 |
| |
| /* Drive Strength */ |
| #define IMPEDANCE_48_OHM 4 |
| #define IMPEDANCE_40_OHM 5 |
| #define IMPEDANCE_34_OHM 6 |
| #define IMPEDANCE_30_OHM 7 |
| #define PHY_CON39_VAL_48_OHM 0x09240924 |
| #define PHY_CON39_VAL_40_OHM 0x0B6D0B6D |
| #define PHY_CON39_VAL_34_OHM 0x0DB60DB6 |
| #define PHY_CON39_VAL_30_OHM 0x0FFF0FFF |
| |
| #define CTRL_BSTLEN_OFFSET 8 |
| #define CTRL_RDLAT_OFFSET 0 |
| |
| #define CMD_DEFAULT_LPDDR3 0xF |
| #define CMD_DEFUALT_OFFSET 0 |
| #define T_WRDATA_EN 0x7 |
| #define T_WRDATA_EN_DDR3 0x8 |
| #define T_WRDATA_EN_OFFSET 16 |
| #define T_WRDATA_EN_MASK 0x1f |
| |
| #define PHY_CON31_VAL 0x0C183060 |
| #define PHY_CON32_VAL 0x60C18306 |
| #define PHY_CON33_VAL 0x00000030 |
| |
| #define PHY_CON31_RESET_VAL 0x0 |
| #define PHY_CON32_RESET_VAL 0x0 |
| #define PHY_CON33_RESET_VAL 0x0 |
| |
| #define SL_DLL_DYN_CON_EN (1 << 1) |
| #define FP_RESYNC (1 << 3) |
| #define CTRL_START (1 << 6) |
| |
| #define DMC_AREF_EN (1 << 5) |
| #define DMC_CONCONTROL_EMPTY (1 << 8) |
| #define DFI_INIT_START (1 << 28) |
| |
| #define DMC_MEMCONTROL_VAL 0x00312700 |
| #define CLK_STOP_EN (1 << 0) |
| #define DPWRDN_EN (1 << 1) |
| #define DSREF_EN (1 << 5) |
| |
| #define MEMBASECONFIG_CHIP_MASK_VAL 0x7E0 |
| #define MEMBASECONFIG_CHIP_MASK_OFFSET 0 |
| #define MEMBASECONFIG0_CHIP_BASE_VAL 0x20 |
| #define MEMBASECONFIG1_CHIP_BASE_VAL 0x40 |
| #define CHIP_BASE_OFFSET 16 |
| |
| #define MEMCONFIG_VAL 0x1323 |
| #define PRECHCONFIG_DEFAULT_VAL 0xFF000000 |
| #define PWRDNCONFIG_DEFAULT_VAL 0xFFFF00FF |
| |
| #define TIMINGAREF_VAL 0x5d |
| #define TIMINGROW_VAL 0x345A8692 |
| #define TIMINGDATA_VAL 0x3630065C |
| #define TIMINGPOWER_VAL 0x50380336 |
| #define DFI_INIT_COMPLETE (1 << 3) |
| |
| #define BRBRSVCONTROL_VAL 0x00000033 |
| #define BRBRSVCONFIG_VAL 0x88778877 |
| |
| /* Clock Gating Control (CGCONTROL) register */ |
| #define MEMIF_CG_EN (1 << 3) /* Memory interface clock gating */ |
| #define SCG_CG_EN (1 << 2) /* Scheduler clock gating */ |
| #define BUSIF_WR_CG_EN (1 << 1) /* Bus interface write channel clock gating */ |
| #define BUSIF_RD_CG_EN (1 << 0) /* Bus interface read channel clock gating */ |
| #define DMC_INTERNAL_CG (MEMIF_CG_EN | SCG_CG_EN | \ |
| BUSIF_WR_CG_EN | BUSIF_RD_CG_EN) |
| |
| /* DMC PHY Control0 register */ |
| #define PHY_CONTROL0_RESET_VAL 0x0 |
| #define MEM_TERM_EN (1 << 31) /* Termination enable for memory */ |
| #define PHY_TERM_EN (1 << 30) /* Termination enable for PHY */ |
| #define DMC_CTRL_SHGATE (1 << 29) /* Duration of DQS gating signal */ |
| #define FP_RSYNC (1 << 3) /* Force DLL resyncronization */ |
| |
| /* Driver strength for CK, CKE, CS & CA */ |
| #define IMP_OUTPUT_DRV_40_OHM 0x5 |
| #define IMP_OUTPUT_DRV_30_OHM 0x7 |
| #define DA_3_DS_OFFSET 25 |
| #define DA_2_DS_OFFSET 22 |
| #define DA_1_DS_OFFSET 19 |
| #define DA_0_DS_OFFSET 16 |
| #define CA_CK_DRVR_DS_OFFSET 9 |
| #define CA_CKE_DRVR_DS_OFFSET 6 |
| #define CA_CS_DRVR_DS_OFFSET 3 |
| #define CA_ADR_DRVR_DS_OFFSET 0 |
| |
| #define PHY_CON42_CTRL_BSTLEN_SHIFT 8 |
| #define PHY_CON42_CTRL_RDLAT_SHIFT 0 |
| |
| /* |
| * Definitions that differ with SoC's. |
| * Below is the part defining macros for Exynos5250. |
| * Else part introduces macros for Exynos5420. |
| */ |
| #ifndef CONFIG_EXYNOS5420 |
| |
| /* APLL_CON1 */ |
| #define APLL_CON1_VAL (0x00203800) |
| |
| /* MPLL_CON1 */ |
| #define MPLL_CON1_VAL (0x00203800) |
| |
| /* CPLL_CON1 */ |
| #define CPLL_CON1_VAL (0x00203800) |
| |
| /* DPLL_CON1 */ |
| #define DPLL_CON1_VAL (NOT_AVAILABLE) |
| |
| /* GPLL_CON1 */ |
| #define GPLL_CON1_VAL (0x00203800) |
| |
| /* EPLL_CON1, CON2 */ |
| #define EPLL_CON1_VAL 0x00000000 |
| #define EPLL_CON2_VAL 0x00000080 |
| |
| /* VPLL_CON1, CON2 */ |
| #define VPLL_CON1_VAL 0x00000000 |
| #define VPLL_CON2_VAL 0x00000080 |
| |
| /* RPLL_CON1, CON2 */ |
| #define RPLL_CON1_VAL NOT_AVAILABLE |
| #define RPLL_CON2_VAL NOT_AVAILABLE |
| |
| /* BPLL_CON1 */ |
| #define BPLL_CON1_VAL 0x00203800 |
| |
| /* SPLL_CON1 */ |
| #define SPLL_CON1_VAL NOT_AVAILABLE |
| |
| /* IPLL_CON1 */ |
| #define IPLL_CON1_VAL NOT_AVAILABLE |
| |
| /* KPLL_CON1 */ |
| #define KPLL_CON1_VAL NOT_AVAILABLE |
| |
| /* CLK_SRC_ISP */ |
| #define CLK_SRC_ISP_VAL NOT_AVAILABLE |
| #define CLK_DIV_ISP0_VAL 0x31 |
| #define CLK_DIV_ISP1_VAL 0x0 |
| |
| /* CLK_FSYS */ |
| #define CLK_SRC_FSYS0_VAL 0x66666 |
| #define CLK_DIV_FSYS0_VAL 0x0BB00000 |
| #define CLK_DIV_FSYS1_VAL NOT_AVAILABLE |
| #define CLK_DIV_FSYS2_VAL NOT_AVAILABLE |
| |
| /* CLK_SRC_CPU */ |
| /* 0 = MOUTAPLL, 1 = SCLKMPLL */ |
| #define MUX_HPM_SEL 0 |
| #define MUX_CPU_SEL 0 |
| #define MUX_APLL_SEL 1 |
| |
| #define CLK_SRC_CPU_VAL ((MUX_HPM_SEL << 20) \ |
| | (MUX_CPU_SEL << 16) \ |
| | (MUX_APLL_SEL)) |
| |
| /* CLK_SRC_CDREX */ |
| #define CLK_SRC_CDREX_VAL 0x1 |
| |
| /* CLK_DIV_CDREX */ |
| #define CLK_DIV_CDREX0_VAL NOT_AVAILABLE |
| #define CLK_DIV_CDREX1_VAL NOT_AVAILABLE |
| |
| /* CLK_DIV_CPU0_VAL */ |
| #define CLK_DIV_CPU0_VAL NOT_AVAILABLE |
| |
| #define MCLK_CDREX2_RATIO 0x0 |
| #define ACLK_EFCON_RATIO 0x1 |
| #define MCLK_DPHY_RATIO 0x1 |
| #define MCLK_CDREX_RATIO 0x1 |
| #define ACLK_C2C_200_RATIO 0x1 |
| #define C2C_CLK_400_RATIO 0x1 |
| #define PCLK_CDREX_RATIO 0x1 |
| #define ACLK_CDREX_RATIO 0x1 |
| |
| #define CLK_DIV_CDREX_VAL ((MCLK_DPHY_RATIO << 24) \ |
| | (C2C_CLK_400_RATIO << 6) \ |
| | (PCLK_CDREX_RATIO << 4) \ |
| | (ACLK_CDREX_RATIO)) |
| |
| /* CLK_SRC_TOP0 */ |
| #define MUX_ACLK_300_GSCL_SEL 0x0 |
| #define MUX_ACLK_300_GSCL_MID_SEL 0x0 |
| #define MUX_ACLK_400_G3D_MID_SEL 0x0 |
| #define MUX_ACLK_333_SEL 0x0 |
| #define MUX_ACLK_300_DISP1_SEL 0x0 |
| #define MUX_ACLK_300_DISP1_MID_SEL 0x0 |
| #define MUX_ACLK_200_SEL 0x0 |
| #define MUX_ACLK_166_SEL 0x0 |
| #define CLK_SRC_TOP0_VAL ((MUX_ACLK_300_GSCL_SEL << 25) \ |
| | (MUX_ACLK_300_GSCL_MID_SEL << 24) \ |
| | (MUX_ACLK_400_G3D_MID_SEL << 20) \ |
| | (MUX_ACLK_333_SEL << 16) \ |
| | (MUX_ACLK_300_DISP1_SEL << 15) \ |
| | (MUX_ACLK_300_DISP1_MID_SEL << 14) \ |
| | (MUX_ACLK_200_SEL << 12) \ |
| | (MUX_ACLK_166_SEL << 8)) |
| |
| /* CLK_SRC_TOP1 */ |
| #define MUX_ACLK_400_G3D_SEL 0x1 |
| #define MUX_ACLK_400_ISP_SEL 0x0 |
| #define MUX_ACLK_400_IOP_SEL 0x0 |
| #define MUX_ACLK_MIPI_HSI_TXBASE_SEL 0x0 |
| #define MUX_ACLK_300_GSCL_MID1_SEL 0x0 |
| #define MUX_ACLK_300_DISP1_MID1_SEL 0x0 |
| #define CLK_SRC_TOP1_VAL ((MUX_ACLK_400_G3D_SEL << 28) \ |
| |(MUX_ACLK_400_ISP_SEL << 24) \ |
| |(MUX_ACLK_400_IOP_SEL << 20) \ |
| |(MUX_ACLK_MIPI_HSI_TXBASE_SEL << 16) \ |
| |(MUX_ACLK_300_GSCL_MID1_SEL << 12) \ |
| |(MUX_ACLK_300_DISP1_MID1_SEL << 8)) |
| |
| /* CLK_SRC_TOP2 */ |
| #define MUX_GPLL_SEL 0x1 |
| #define MUX_BPLL_USER_SEL 0x0 |
| #define MUX_MPLL_USER_SEL 0x0 |
| #define MUX_VPLL_SEL 0x1 |
| #define MUX_EPLL_SEL 0x1 |
| #define MUX_CPLL_SEL 0x1 |
| #define VPLLSRC_SEL 0x0 |
| #define CLK_SRC_TOP2_VAL ((MUX_GPLL_SEL << 28) \ |
| | (MUX_BPLL_USER_SEL << 24) \ |
| | (MUX_MPLL_USER_SEL << 20) \ |
| | (MUX_VPLL_SEL << 16) \ |
| | (MUX_EPLL_SEL << 12) \ |
| | (MUX_CPLL_SEL << 8) \ |
| | (VPLLSRC_SEL)) |
| /* CLK_SRC_TOP3 */ |
| #define MUX_ACLK_333_SUB_SEL 0x1 |
| #define MUX_ACLK_400_SUB_SEL 0x1 |
| #define MUX_ACLK_266_ISP_SUB_SEL 0x1 |
| #define MUX_ACLK_266_GPS_SUB_SEL 0x0 |
| #define MUX_ACLK_300_GSCL_SUB_SEL 0x1 |
| #define MUX_ACLK_266_GSCL_SUB_SEL 0x1 |
| #define MUX_ACLK_300_DISP1_SUB_SEL 0x1 |
| #define MUX_ACLK_200_DISP1_SUB_SEL 0x1 |
| #define CLK_SRC_TOP3_VAL ((MUX_ACLK_333_SUB_SEL << 24) \ |
| | (MUX_ACLK_400_SUB_SEL << 20) \ |
| | (MUX_ACLK_266_ISP_SUB_SEL << 16) \ |
| | (MUX_ACLK_266_GPS_SUB_SEL << 12) \ |
| | (MUX_ACLK_300_GSCL_SUB_SEL << 10) \ |
| | (MUX_ACLK_266_GSCL_SUB_SEL << 8) \ |
| | (MUX_ACLK_300_DISP1_SUB_SEL << 6) \ |
| | (MUX_ACLK_200_DISP1_SUB_SEL << 4)) |
| |
| #define CLK_SRC_TOP4_VAL NOT_AVAILABLE |
| #define CLK_SRC_TOP5_VAL NOT_AVAILABLE |
| #define CLK_SRC_TOP6_VAL NOT_AVAILABLE |
| #define CLK_SRC_TOP7_VAL NOT_AVAILABLE |
| |
| /* CLK_DIV_TOP0 */ |
| #define ACLK_300_DISP1_RATIO 0x2 |
| #define ACLK_400_G3D_RATIO 0x0 |
| #define ACLK_333_RATIO 0x0 |
| #define ACLK_266_RATIO 0x2 |
| #define ACLK_200_RATIO 0x3 |
| #define ACLK_166_RATIO 0x1 |
| #define ACLK_133_RATIO 0x1 |
| #define ACLK_66_RATIO 0x5 |
| |
| #define CLK_DIV_TOP0_VAL ((ACLK_300_DISP1_RATIO << 28) \ |
| | (ACLK_400_G3D_RATIO << 24) \ |
| | (ACLK_333_RATIO << 20) \ |
| | (ACLK_266_RATIO << 16) \ |
| | (ACLK_200_RATIO << 12) \ |
| | (ACLK_166_RATIO << 8) \ |
| | (ACLK_133_RATIO << 4) \ |
| | (ACLK_66_RATIO)) |
| |
| /* CLK_DIV_TOP1 */ |
| #define ACLK_MIPI_HSI_TX_BASE_RATIO 0x3 |
| #define ACLK_66_PRE_RATIO 0x1 |
| #define ACLK_400_ISP_RATIO 0x1 |
| #define ACLK_400_IOP_RATIO 0x1 |
| #define ACLK_300_GSCL_RATIO 0x2 |
| |
| #define CLK_DIV_TOP1_VAL ((ACLK_MIPI_HSI_TX_BASE_RATIO << 28) \ |
| | (ACLK_66_PRE_RATIO << 24) \ |
| | (ACLK_400_ISP_RATIO << 20) \ |
| | (ACLK_400_IOP_RATIO << 16) \ |
| | (ACLK_300_GSCL_RATIO << 12)) |
| |
| #define CLK_DIV_TOP2_VAL NOT_AVAILABLE |
| |
| /* PLL Lock Value Factor */ |
| #define PLL_LOCK_FACTOR 250 |
| #define PLL_X_LOCK_FACTOR 3000 |
| |
| /* CLK_SRC_PERIC0 */ |
| #define PWM_SEL 6 |
| #define UART3_SEL 6 |
| #define UART2_SEL 6 |
| #define UART1_SEL 6 |
| #define UART0_SEL 6 |
| /* SRC_CLOCK = SCLK_MPLL */ |
| #define CLK_SRC_PERIC0_VAL ((PWM_SEL << 24) \ |
| | (UART3_SEL << 12) \ |
| | (UART2_SEL << 8) \ |
| | (UART1_SEL << 4) \ |
| | (UART0_SEL)) |
| |
| /* CLK_SRC_PERIC1 */ |
| /* SRC_CLOCK = SCLK_MPLL */ |
| #define SPI0_SEL 6 |
| #define SPI1_SEL 6 |
| #define SPI2_SEL 6 |
| #define CLK_SRC_PERIC1_VAL ((SPI2_SEL << 24) \ |
| | (SPI1_SEL << 20) \ |
| | (SPI0_SEL << 16)) |
| |
| /* CLK_DIV_PERIL0 */ |
| #define UART5_RATIO 7 |
| #define UART4_RATIO 7 |
| #define UART3_RATIO 7 |
| #define UART2_RATIO 7 |
| #define UART1_RATIO 7 |
| #define UART0_RATIO 7 |
| |
| #define CLK_DIV_PERIC0_VAL ((UART3_RATIO << 12) \ |
| | (UART2_RATIO << 8) \ |
| | (UART1_RATIO << 4) \ |
| | (UART0_RATIO)) |
| /* CLK_DIV_PERIC1 */ |
| #define SPI1_RATIO 0x7 |
| #define SPI0_RATIO 0xf |
| #define SPI1_SUB_RATIO 0x0 |
| #define SPI0_SUB_RATIO 0x0 |
| #define CLK_DIV_PERIC1_VAL ((SPI1_SUB_RATIO << 24) \ |
| | ((SPI1_RATIO << 16) \ |
| | (SPI0_SUB_RATIO << 8) \ |
| | (SPI0_RATIO << 0))) |
| |
| /* CLK_DIV_PERIC2 */ |
| #define SPI2_RATIO 0xf |
| #define SPI2_SUB_RATIO 0x0 |
| #define CLK_DIV_PERIC2_VAL ((SPI2_SUB_RATIO << 8) \ |
| | (SPI2_RATIO << 0)) |
| |
| /* CLK_DIV_PERIC3 */ |
| #define PWM_RATIO 8 |
| #define CLK_DIV_PERIC3_VAL (PWM_RATIO << 0) |
| |
| |
| /* CLK_DIV_PERIC4 */ |
| #define CLK_DIV_PERIC4_VAL NOT_AVAILABLE |
| |
| /* CLK_SRC_DISP1_0 */ |
| #define CLK_SRC_DISP1_0_VAL 0x6 |
| #define CLK_DIV_DISP1_0_VAL NOT_AVAILABLE |
| |
| #define APLL_FOUT (1 << 0) |
| #define KPLL_FOUT NOT_AVAILABLE |
| |
| #define CLK_DIV_CPERI1_VAL NOT_AVAILABLE |
| |
| #else |
| |
| #define CPU_CONFIG_STATUS_OFFSET 0x80 |
| #define CPU_RST_FLAG_VAL 0xFCBA0D10 |
| #define PAD_RETENTION_DRAM_COREBLK_VAL 0x10000000 |
| |
| /* APLL_CON1 */ |
| #define APLL_CON1_VAL (0x0020F300) |
| |
| /* MPLL_CON1 */ |
| #define MPLL_CON1_VAL (0x0020F300) |
| |
| |
| /* CPLL_CON1 */ |
| #define CPLL_CON1_VAL 0x0020f300 |
| |
| /* DPLL_CON1 */ |
| #define DPLL_CON1_VAL (0x0020F300) |
| |
| /* GPLL_CON1 */ |
| #define GPLL_CON1_VAL (NOT_AVAILABLE) |
| |
| |
| /* EPLL_CON1, CON2 */ |
| #define EPLL_CON1_VAL 0x00000000 |
| #define EPLL_CON2_VAL 0x00000080 |
| |
| /* VPLL_CON1, CON2 */ |
| #define VPLL_CON1_VAL 0x0020f300 |
| #define VPLL_CON2_VAL NOT_AVAILABLE |
| |
| /* RPLL_CON1, CON2 */ |
| #define RPLL_CON1_VAL 0x00000000 |
| #define RPLL_CON2_VAL 0x00000080 |
| |
| /* BPLL_CON1 */ |
| #define BPLL_CON1_VAL 0x0020f300 |
| |
| /* SPLL_CON1 */ |
| #define SPLL_CON1_VAL 0x0020f300 |
| |
| /* IPLL_CON1 */ |
| #define IPLL_CON1_VAL 0x00000080 |
| |
| /* KPLL_CON1 */ |
| #define KPLL_CON1_VAL 0x200000 |
| |
| /* CLK_SRC_ISP */ |
| #define CLK_SRC_ISP_VAL 0x33366000 |
| #define CLK_DIV_ISP0_VAL 0x13131300 |
| #define CLK_DIV_ISP1_VAL 0xbb110202 |
| |
| |
| /* CLK_FSYS */ |
| #define CLK_SRC_FSYS0_VAL 0x33033300 |
| #define CLK_DIV_FSYS0_VAL 0x0 |
| #define CLK_DIV_FSYS1_VAL 0x04f13c4f |
| #define CLK_DIV_FSYS2_VAL 0x041d0000 |
| |
| /* CLK_SRC_CPU */ |
| /* 0 = MOUTAPLL, 1 = SCLKMPLL */ |
| #define MUX_HPM_SEL 1 |
| #define MUX_CPU_SEL 0 |
| #define MUX_APLL_SEL 1 |
| |
| #define CLK_SRC_CPU_VAL ((MUX_HPM_SEL << 20) \ |
| | (MUX_CPU_SEL << 16) \ |
| | (MUX_APLL_SEL)) |
| |
| /* CLK_SRC_CDREX */ |
| #define CLK_SRC_CDREX_VAL 0x00000011 |
| |
| /* CLK_DIV_CDREX */ |
| #define CLK_DIV_CDREX0_VAL 0x30010100 |
| #define CLK_DIV_CDREX1_VAL 0x300 |
| |
| #define CLK_DIV_CDREX_VAL 0x17010100 |
| |
| /* CLK_DIV_CPU0_VAL */ |
| #define CLK_DIV_CPU0_VAL 0x01440020 |
| |
| /* CLK_SRC_TOP */ |
| #define CLK_SRC_TOP0_VAL 0x12221222 |
| #define CLK_SRC_TOP1_VAL 0x00100200 |
| #define CLK_SRC_TOP2_VAL 0x11101000 |
| #define CLK_SRC_TOP3_VAL 0x11111111 |
| #define CLK_SRC_TOP4_VAL 0x11110111 |
| #define CLK_SRC_TOP5_VAL 0x11111101 |
| #define CLK_SRC_TOP6_VAL 0x11110111 |
| #define CLK_SRC_TOP7_VAL 0x00022200 |
| |
| /* CLK_DIV_TOP */ |
| #define CLK_DIV_TOP0_VAL 0x23712311 |
| #define CLK_DIV_TOP1_VAL 0x13100B00 |
| #define CLK_DIV_TOP2_VAL 0x11101100 |
| |
| /* PLL Lock Value Factor */ |
| #define PLL_LOCK_FACTOR 200 |
| #define PLL_X_LOCK_FACTOR 3000 |
| |
| /* CLK_SRC_PERIC0 */ |
| #define SPDIF_SEL 1 |
| #define PWM_SEL 3 |
| #define UART4_SEL 3 |
| #define UART3_SEL 3 |
| #define UART2_SEL 3 |
| #define UART1_SEL 3 |
| #define UART0_SEL 3 |
| /* SRC_CLOCK = SCLK_RPLL */ |
| #define CLK_SRC_PERIC0_VAL ((SPDIF_SEL << 28) \ |
| | (PWM_SEL << 24) \ |
| | (UART4_SEL << 20) \ |
| | (UART3_SEL << 16) \ |
| | (UART2_SEL << 12) \ |
| | (UART1_SEL << 8) \ |
| | (UART0_SEL << 4)) |
| |
| /* CLK_SRC_PERIC1 */ |
| /* SRC_CLOCK = SCLK_EPLL */ |
| #define SPI0_SEL 6 |
| #define SPI1_SEL 6 |
| #define SPI2_SEL 6 |
| #define AUDIO0_SEL 6 |
| #define AUDIO1_SEL 6 |
| #define AUDIO2_SEL 6 |
| #define CLK_SRC_PERIC1_VAL ((SPI2_SEL << 28) \ |
| | (SPI1_SEL << 24) \ |
| | (SPI0_SEL << 20) \ |
| | (AUDIO2_SEL << 16) \ |
| | (AUDIO2_SEL << 12) \ |
| | (AUDIO2_SEL << 8)) |
| |
| /* CLK_DIV_PERIC0 */ |
| #define PWM_RATIO 8 |
| #define UART4_RATIO 9 |
| #define UART3_RATIO 9 |
| #define UART2_RATIO 9 |
| #define UART1_RATIO 9 |
| #define UART0_RATIO 9 |
| |
| #define CLK_DIV_PERIC0_VAL ((PWM_RATIO << 28) \ |
| | (UART4_RATIO << 24) \ |
| | (UART3_RATIO << 20) \ |
| | (UART2_RATIO << 16) \ |
| | (UART1_RATIO << 12) \ |
| | (UART0_RATIO << 8)) |
| /* CLK_DIV_PERIC1 */ |
| #define SPI2_RATIO 0x1 |
| #define SPI1_RATIO 0x1 |
| #define SPI0_RATIO 0x1 |
| #define CLK_DIV_PERIC1_VAL ((SPI2_RATIO << 28) \ |
| | (SPI1_RATIO << 24) \ |
| | (SPI0_RATIO << 20)) |
| |
| /* CLK_DIV_PERIC2 */ |
| #define PCM2_RATIO 0x3 |
| #define PCM1_RATIO 0x3 |
| #define CLK_DIV_PERIC2_VAL ((PCM2_RATIO << 24) \ |
| | (PCM1_RATIO << 16)) |
| |
| /* CLK_DIV_PERIC3 */ |
| #define AUDIO2_RATIO 0x5 |
| #define AUDIO1_RATIO 0x5 |
| #define AUDIO0_RATIO 0x5 |
| #define CLK_DIV_PERIC3_VAL ((AUDIO2_RATIO << 28) \ |
| | (AUDIO1_RATIO << 24) \ |
| | (AUDIO0_RATIO << 20)) |
| |
| /* CLK_DIV_PERIC4 */ |
| #define SPI2_PRE_RATIO 0x2 |
| #define SPI1_PRE_RATIO 0x2 |
| #define SPI0_PRE_RATIO 0x2 |
| #define CLK_DIV_PERIC4_VAL ((SPI2_PRE_RATIO << 24) \ |
| | (SPI1_PRE_RATIO << 16) \ |
| | (SPI0_PRE_RATIO << 8)) |
| |
| /* CLK_SRC_DISP1_0 */ |
| #define CLK_SRC_DISP1_0_VAL 0x10666600 |
| #define CLK_DIV_DISP1_0_VAL 0x01050211 |
| |
| #define APLL_FOUT (1 << 0) |
| #define KPLL_FOUT (1 << 0) |
| |
| #define CLK_DIV_CPERI1_VAL 0x3f3f0000 |
| #endif |
| |
| struct mem_timings; |
| |
| /* Errors that we can encourter in low-level setup */ |
| enum { |
| SETUP_ERR_OK, |
| SETUP_ERR_RDLV_COMPLETE_TIMEOUT = -1, |
| SETUP_ERR_ZQ_CALIBRATION_FAILURE = -2, |
| }; |
| |
| /* |
| * Memory variant specific initialization code for DDR3 |
| * |
| * @param mem Memory timings for this memory type. |
| * @param reset Reset DDR PHY during initialization. |
| * Return: 0 if ok, SETUP_ERR_... if there is a problem |
| */ |
| int ddr3_mem_ctrl_init(struct mem_timings *mem, int reset); |
| |
| /* Memory variant specific initialization code for LPDDR3 */ |
| void lpddr3_mem_ctrl_init(void); |
| |
| /* |
| * Configure ZQ I/O interface |
| * |
| * @param mem Memory timings for this memory type. |
| * @param phy0_con16 Register address for dmc_phy0->phy_con16 |
| * @param phy1_con16 Register address for dmc_phy1->phy_con16 |
| * @param phy0_con17 Register address for dmc_phy0->phy_con17 |
| * @param phy1_con17 Register address for dmc_phy1->phy_con17 |
| * Return: 0 if ok, -1 on error |
| */ |
| int dmc_config_zq(struct mem_timings *mem, uint32_t *phy0_con16, |
| uint32_t *phy1_con16, uint32_t *phy0_con17, |
| uint32_t *phy1_con17); |
| /* |
| * Send NOP and MRS/EMRS Direct commands |
| * |
| * @param mem Memory timings for this memory type. |
| * @param directcmd Register address for dmc_phy->directcmd |
| */ |
| void dmc_config_mrs(struct mem_timings *mem, uint32_t *directcmd); |
| |
| /* |
| * Send PALL Direct commands |
| * |
| * @param mem Memory timings for this memory type. |
| * @param directcmd Register address for dmc_phy->directcmd |
| */ |
| void dmc_config_prech(struct mem_timings *mem, uint32_t *directcmd); |
| |
| /* |
| * Reset the DLL. This function is common between DDR3 and LPDDR2. |
| * However, the reset value is different. So we are passing a flag |
| * ddr_mode to distinguish between LPDDR2 and DDR3. |
| * |
| * @param phycontrol0 Register address for dmc_phy->phycontrol0 |
| * @param ddr_mode Type of DDR memory |
| */ |
| void update_reset_dll(uint32_t *phycontrol0, enum ddr_mode); |
| #endif |