| /* |
| * (C) Copyright 2000-2005 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| /* |
| * board/config.h - configuration options, board specific |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| |
| #define CONFIG_MPC860 1 /* This is a MPC860 CPU */ |
| #define CONFIG_IP860 1 /* ...on a IP860 board */ |
| |
| #define CONFIG_SYS_TEXT_BASE 0x10000000 |
| |
| #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ |
| #define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */ |
| |
| #define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ |
| #define CONFIG_BAUDRATE 9600 |
| #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ |
| |
| #define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo" \ |
| "\0load=tftp \"/tftpboot/u-boot.bin\"\0update=protect off 1:0;era 1:0;cp.b 100000 10000000 ${filesize}\0" |
| |
| #undef CONFIG_BOOTARGS |
| #define CONFIG_BOOTCOMMAND \ |
| "bootp; " \ |
| "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ |
| "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \ |
| "bootm" |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| |
| /* enable I2C and select the hardware/software driver */ |
| #undef CONFIG_HARD_I2C /* I2C with hardware support */ |
| #define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ |
| /* |
| * Software (bit-bang) I2C driver configuration |
| */ |
| #define PB_SCL 0x00000020 /* PB 26 */ |
| #define PB_SDA 0x00000010 /* PB 27 */ |
| |
| #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) |
| #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) |
| #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) |
| #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) |
| #define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ |
| else immr->im_cpm.cp_pbdat &= ~PB_SDA |
| #define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ |
| else immr->im_cpm.cp_pbdat &= ~PB_SCL |
| #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ |
| |
| |
| # define CONFIG_SYS_I2C_SPEED 50000 |
| # define CONFIG_SYS_I2C_SLAVE 0xFE |
| # define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM X24C16 */ |
| # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ |
| /* mask of address bits that overflow into the "EEPROM chip address" */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* takes up to 10 msec */ |
| |
| #define CONFIG_TIMESTAMP /* Print image info with timestamp */ |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_BEDBUG |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_EEPROM |
| #define CONFIG_CMD_NFS |
| #define CONFIG_CMD_SNTP |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_SUBNETMASK |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| #define CONFIG_BOOTP_BOOTPATH |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */ |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ |
| |
| #define CONFIG_SYS_PIO_MODE 0 /* IDE interface in PIO Mode 0 */ |
| |
| #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } |
| |
| /* |
| * Low Level Configuration Settings |
| * (address mappings, register initial values, etc.) |
| * You should know what you are doing if you make changes here. |
| */ |
| /*----------------------------------------------------------------------- |
| * Internal Memory Mapped Register |
| */ |
| #define CONFIG_SYS_IMMR 0xF1000000 /* Non-standard value!! */ |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for initial stack pointer and data area (in DPRAM) |
| */ |
| #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR |
| #define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ |
| #define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /*----------------------------------------------------------------------- |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 |
| */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_FLASH_BASE 0x10000000 |
| #ifdef DEBUG |
| #define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */ |
| #else |
| #if 0 /* need more space for I2C tests */ |
| #define CONFIG_SYS_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */ |
| #else |
| #define CONFIG_SYS_MONITOR_LEN (256 << 10) |
| #endif |
| #endif |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE |
| #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| /*----------------------------------------------------------------------- |
| * FLASH organization |
| */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 124 /* max number of sectors on one chip */ |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| #undef CONFIG_ENV_IS_IN_FLASH |
| #undef CONFIG_ENV_IS_IN_NVRAM |
| #undef CONFIG_ENV_IS_IN_NVRAM |
| #undef DEBUG_I2C |
| #define CONFIG_ENV_IS_IN_EEPROM |
| |
| #ifdef CONFIG_ENV_IS_IN_NVRAM |
| #define CONFIG_ENV_ADDR 0x20000000 /* use SRAM */ |
| #define CONFIG_ENV_SIZE (16<<10) /* use 16 kB */ |
| #endif /* CONFIG_ENV_IS_IN_NVRAM */ |
| |
| #ifdef CONFIG_ENV_IS_IN_EEPROM |
| #define CONFIG_ENV_OFFSET 512 /* Leave 512 bytes free for other data */ |
| #define CONFIG_ENV_SIZE 1536 /* Use remaining space */ |
| #endif /* CONFIG_ENV_IS_IN_EEPROM */ |
| |
| /*----------------------------------------------------------------------- |
| * Cache Configuration |
| */ |
| #define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ |
| #endif |
| #define CONFIG_SYS_DELAYED_ICACHE 1 /* enable ICache not before |
| * running in RAM. |
| */ |
| |
| /*----------------------------------------------------------------------- |
| * SYPCR - System Protection Control 11-9 |
| * SYPCR can only be written once after reset! |
| *----------------------------------------------------------------------- |
| * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze |
| * +0x0004 |
| */ |
| #if defined(CONFIG_WATCHDOG) |
| #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ |
| SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) |
| #else |
| #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * SIUMCR - SIU Module Configuration 11-6 |
| *----------------------------------------------------------------------- |
| * +0x0000 => 0x80600800 |
| */ |
| #define CONFIG_SYS_SIUMCR (SIUMCR_EARB | SIUMCR_EARP0 | \ |
| SIUMCR_DBGC11 | SIUMCR_MLRC10) |
| |
| /*----------------------------------------------------------------------- |
| * Clock Setting - get clock frequency from Board Revision Register |
| *----------------------------------------------------------------------- |
| */ |
| #ifndef __ASSEMBLY__ |
| extern unsigned long ip860_get_clk_freq (void); |
| #endif |
| #define CONFIG_8xx_GCLK_FREQ ip860_get_clk_freq() |
| |
| /*----------------------------------------------------------------------- |
| * TBSCR - Time Base Status and Control 11-26 |
| *----------------------------------------------------------------------- |
| * Clear Reference Interrupt Status, Timebase freezing enabled |
| * +0x0200 => 0x00C2 |
| */ |
| #define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) |
| |
| /*----------------------------------------------------------------------- |
| * PISCR - Periodic Interrupt Status and Control 11-31 |
| *----------------------------------------------------------------------- |
| * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled |
| * +0x0240 => 0x0082 |
| */ |
| #define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) |
| |
| /*----------------------------------------------------------------------- |
| * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 |
| *----------------------------------------------------------------------- |
| * Reset PLL lock status sticky bit, timer expired status bit and timer |
| * interrupt status bit, set PLL multiplication factor ! |
| */ |
| /* +0x0286 => was: 0x0000D000 */ |
| #define CONFIG_SYS_PLPRCR \ |
| ( PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | \ |
| /*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \ |
| PLPRCR_CSR | PLPRCR_LOLRE /*|PLPRCR_FIOPD*/ \ |
| ) |
| |
| /*----------------------------------------------------------------------- |
| * SCCR - System Clock and reset Control Register 15-27 |
| *----------------------------------------------------------------------- |
| * Set clock output, timebase and RTC source and divider, |
| * power management and some other internal clocks |
| */ |
| #define SCCR_MASK SCCR_EBDF11 |
| #define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_TBS | \ |
| SCCR_RTDIV | SCCR_RTSEL | \ |
| /*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \ |
| SCCR_EBDF00 | SCCR_DFSYNC00 | \ |
| SCCR_DFBRG00 | SCCR_DFNL000 | \ |
| SCCR_DFNH000) |
| |
| /*----------------------------------------------------------------------- |
| * RTCSC - Real-Time Clock Status and Control Register 11-27 |
| *----------------------------------------------------------------------- |
| */ |
| /* +0x0220 => 0x00C3 */ |
| #define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) |
| |
| |
| /*----------------------------------------------------------------------- |
| * RCCR - RISC Controller Configuration Register 19-4 |
| *----------------------------------------------------------------------- |
| */ |
| /* +0x09C4 => TIMEP=1 */ |
| #define CONFIG_SYS_RCCR 0x0100 |
| |
| /*----------------------------------------------------------------------- |
| * RMDS - RISC Microcode Development Support Control Register |
| *----------------------------------------------------------------------- |
| */ |
| #define CONFIG_SYS_RMDS 0 |
| |
| /*----------------------------------------------------------------------- |
| * DER - Debug Event Register |
| *----------------------------------------------------------------------- |
| * |
| */ |
| #define CONFIG_SYS_DER 0 |
| |
| /* |
| * Init Memory Controller: |
| */ |
| |
| /* |
| * MAMR settings for SDRAM - 16-14 |
| * => 0xC3804114 |
| */ |
| |
| /* periodic timer for refresh */ |
| #define CONFIG_SYS_MAMR_PTA 0xC3 |
| |
| #define CONFIG_SYS_MAMR ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ |
| MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ |
| MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) |
| /* |
| * BR1 and OR1 (FLASH) |
| */ |
| #define FLASH_BASE 0x10000000 /* FLASH bank #0 */ |
| |
| /* used to re-map FLASH |
| * restrict access enough to keep SRAM working (if any) |
| * but not too much to meddle with FLASH accesses |
| */ |
| /* allow for max 8 MB of Flash */ |
| #define CONFIG_SYS_REMAP_OR_AM 0xFF800000 /* OR addr mask */ |
| #define CONFIG_SYS_PRELIM_OR_AM 0xFF800000 /* OR addr mask */ |
| |
| #define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | OR_SCY_6_CLK) |
| |
| #define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) |
| #define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) |
| /* 16 bit, bank valid */ |
| #define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE & BR_BA_MSK) | BR_PS_32 | BR_V ) |
| |
| #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM |
| #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_BR0_PRELIM |
| |
| /* |
| * BR2/OR2 - SDRAM |
| */ |
| #define SDRAM_BASE 0x00000000 /* SDRAM bank */ |
| #define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */ |
| #define SDRAM_TIMING 0x00000A00 /* SDRAM-Timing */ |
| |
| #define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB SDRAM */ |
| |
| #define CONFIG_SYS_OR2 (SDRAM_PRELIM_OR_AM | SDRAM_TIMING ) |
| #define CONFIG_SYS_BR2 ((SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V ) |
| |
| /* |
| * BR3/OR3 - SRAM (16 bit) |
| */ |
| #define SRAM_BASE 0x20000000 |
| #define CONFIG_SYS_OR3 0xFFF00130 /* BI/SCY = 5/TRLX (internal) */ |
| #define CONFIG_SYS_BR3 ((SRAM_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) |
| #define SRAM_SIZE (1 + (~(CONFIG_SYS_OR3 & BR_BA_MSK))) |
| #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR3 /* Make sure to map early */ |
| #define CONFIG_SYS_BR3_PRELIM CONFIG_SYS_BR3 /* in case it's used for ENV */ |
| #define CONFIG_SYS_SRAM_BASE SRAM_BASE |
| #define CONFIG_SYS_SRAM_SIZE SRAM_SIZE |
| |
| /* |
| * BR4/OR4 - Board Control & Status (8 bit) |
| */ |
| #define BCSR_BASE 0xFC000000 |
| #define CONFIG_SYS_OR4 0xFFFF0120 /* BI (internal) */ |
| #define CONFIG_SYS_BR4 ((BCSR_BASE & BR_BA_MSK) | BR_PS_8 | BR_V) |
| |
| /* |
| * BR5/OR5 - IP Slot A/B (16 bit) |
| */ |
| #define IP_SLOT_BASE 0x40000000 |
| #define CONFIG_SYS_OR5 0xFE00010C /* SETA/TRLX/BI/ SCY=0 (external) */ |
| #define CONFIG_SYS_BR5 ((IP_SLOT_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) |
| |
| /* |
| * BR6/OR6 - VME STD (16 bit) |
| */ |
| #define VME_STD_BASE 0xFE000000 |
| #define CONFIG_SYS_OR6 0xFF00010C /* SETA/TRLX/BI/SCY=0 (external) */ |
| #define CONFIG_SYS_BR6 ((VME_STD_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) |
| |
| /* |
| * BR7/OR7 - SHORT I/O + RTC + IACK (16 bit) |
| */ |
| #define VME_SHORT_BASE 0xFF000000 |
| #define CONFIG_SYS_OR7 0xFF00010C /* SETA/TRLX/BI/ SCY=0 (external) */ |
| #define CONFIG_SYS_BR7 ((VME_SHORT_BASE & BR_BA_MSK) | BR_PS_16 | BR_V) |
| |
| /*----------------------------------------------------------------------- |
| * Board Control and Status Region: |
| *----------------------------------------------------------------------- |
| */ |
| #ifndef __ASSEMBLY__ |
| typedef struct ip860_bcsr_s { |
| unsigned char shmem_addr; /* +00 shared memory address register */ |
| unsigned char reserved0; |
| unsigned char mbox_addr; /* +02 mailbox address register */ |
| unsigned char reserved1; |
| unsigned char vme_int_mask; /* +04 VME Bus interrupt mask register */ |
| unsigned char reserved2; |
| unsigned char vme_int_pend; /* +06 VME interrupt pending register */ |
| unsigned char reserved3; |
| unsigned char bd_int_mask; /* +08 board interrupt mask register */ |
| unsigned char reserved4; |
| unsigned char bd_int_pend; /* +0A board interrupt pending register */ |
| unsigned char reserved5; |
| unsigned char bd_ctrl; /* +0C board control register */ |
| unsigned char reserved6; |
| unsigned char bd_status; /* +0E board status register */ |
| unsigned char reserved7; |
| unsigned char vme_irq; /* +10 VME interrupt request register */ |
| unsigned char reserved8; |
| unsigned char vme_ivec; /* +12 VME interrupt vector register */ |
| unsigned char reserved9; |
| unsigned char cli_mbox; /* +14 clear mailbox irq */ |
| unsigned char reservedA; |
| unsigned char rtc; /* +16 RTC control register */ |
| unsigned char reservedB; |
| unsigned char mbox_data; /* +18 mailbox read/write register */ |
| unsigned char reservedC; |
| unsigned char wd_trigger; /* +1A Watchdog trigger register */ |
| unsigned char reservedD; |
| unsigned char rmw_req; /* +1C RMW request register */ |
| unsigned char reservedE; |
| unsigned char bd_rev; /* +1E Board Revision register */ |
| } ip860_bcsr_t; |
| #endif /* __ASSEMBLY__ */ |
| |
| /*----------------------------------------------------------------------- |
| * Board Control Register: bd_ctrl (Offset 0x0C) |
| *----------------------------------------------------------------------- |
| */ |
| #define BD_CTRL_IPLSE 0x80 /* IP Slot Long Select Enable */ |
| #define BD_CTRL_WDOGE 0x40 /* Watchdog Enable */ |
| #define BD_CTRL_FLWE 0x20 /* Flash Write Enable */ |
| #define BD_CTRL_RWDN 0x10 /* VMEBus Requester Release When Done Enable */ |
| |
| /*----------------------------------------------------------------------- |
| * |
| *----------------------------------------------------------------------- |
| * |
| */ |
| |
| /* |
| * Internal Definitions |
| * |
| * Boot Flags |
| */ |
| #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ |
| #define BOOTFLAG_WARM 0x02 /* Software reboot */ |
| |
| #endif /* __CONFIG_H */ |