| /* |
| * (C) Copyright 2008 |
| * Gary Jennejohn, DENX Software Engineering GmbH, garyj@denx.de. |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| /************************************************************************ |
| * quad100hd.h - configuration for Quad100hd board |
| ***********************************************************************/ |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /*----------------------------------------------------------------------- |
| * High Level Configuration Options |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_QUAD100HD 1 /* Board is Quad100hd */ |
| #define CONFIG_4xx 1 /* ... PPC4xx family */ |
| #define CONFIG_405EP 1 /* Specifc 405EP support*/ |
| |
| #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ |
| |
| #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ |
| |
| #define PLLMR0_DEFAULT PLLMR0_266_133_66 /* no PCI */ |
| #define PLLMR1_DEFAULT PLLMR1_266_133_66 /* no PCI */ |
| |
| /* the environment is in the EEPROM by default */ |
| #define CONFIG_ENV_IS_IN_EEPROM |
| #undef CFG_ENV_IS_IN_FLASH |
| |
| #define CONFIG_NET_MULTI 1 |
| #define CONFIG_HAS_ETH1 1 |
| #define CONFIG_MII 1 /* MII PHY management */ |
| #define CONFIG_PHY_ADDR 0x01 /* PHY address */ |
| #define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */ |
| #define CONFIG_PHY_RESET 1 |
| #define CONFIG_PHY_RESET_DELAY 300 /* PHY RESET recovery delay */ |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #undef CONFIG_CMD_ASKENV |
| #undef CONFIG_CMD_CACHE |
| #define CONFIG_CMD_DHCP |
| #undef CONFIG_CMD_DIAG |
| #define CONFIG_CMD_EEPROM |
| #undef CONFIG_CMD_ELF |
| #define CONFIG_CMD_I2C |
| #undef CONFIG_CMD_IRQ |
| #define CONFIG_CMD_JFFS2 |
| #undef CONFIG_CMD_LOG |
| #undef CONFIG_CMD_MII |
| #define CONFIG_CMD_NAND |
| #undef CONFIG_CMD_PING |
| #define CONFIG_CMD_REGINFO |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| /*----------------------------------------------------------------------- |
| * SDRAM |
| *----------------------------------------------------------------------*/ |
| /* |
| * SDRAM configuration (please see cpu/ppc/sdram.[ch]) |
| */ |
| #define CONFIG_SDRAM_BANK0 1 |
| #define CFG_SDRAM_SIZE 0x02000000 /* 32 MB */ |
| |
| /* FIX! SDRAM timings used in datasheet */ |
| #define CFG_SDRAM_CL 3 /* CAS latency */ |
| #define CFG_SDRAM_tRP 20 /* PRECHARGE command period */ |
| #define CFG_SDRAM_tRC 66 /* ACTIVE-to-ACTIVE command period */ |
| #define CFG_SDRAM_tRCD 20 /* ACTIVE-to-READ delay */ |
| #define CFG_SDRAM_tRFC 66 /* Auto refresh period */ |
| |
| /* |
| * JFFS2 |
| */ |
| #define CFG_JFFS2_FIRST_BANK 0 |
| #ifdef CFG_KERNEL_IN_JFFS2 |
| #define CFG_JFFS2_FIRST_SECTOR 0 /* JFFS starts at block 0 */ |
| #else /* kernel not in JFFS */ |
| #define CFG_JFFS2_FIRST_SECTOR 8 /* block 0-7 is kernel (1MB = 8 sectors) */ |
| #endif |
| #define CFG_JFFS2_NUM_BANKS 1 |
| |
| /*----------------------------------------------------------------------- |
| * Serial Port |
| *----------------------------------------------------------------------*/ |
| #undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ |
| #define CFG_BASE_BAUD 691200 |
| #define CONFIG_BAUDRATE 115200 |
| #define CONFIG_SERIAL_MULTI |
| |
| /* The following table includes the supported baudrates */ |
| #define CFG_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} |
| |
| /*----------------------------------------------------------------------- |
| * Miscellaneous configurable options |
| *----------------------------------------------------------------------*/ |
| #define CFG_LONGHELP /* undef to save memory */ |
| #define CFG_PROMPT "=> " /* Monitor Command Prompt */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ |
| #define CFG_MAXARGS 16 /* max number of command args */ |
| #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CFG_MEMTEST_START 0x0400000 /* memtest works on */ |
| #define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ |
| |
| #define CFG_LOAD_ADDR 0x100000 /* default load address */ |
| #define CFG_EXTBDINFO 1 /* To use extended board_info (bd_t) */ |
| |
| #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ |
| #define CONFIG_LOOPW 1 /* enable loopw command */ |
| #define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ |
| #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ |
| #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ |
| |
| /*----------------------------------------------------------------------- |
| * I2C |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ |
| #undef CONFIG_SOFT_I2C /* I2C bit-banged */ |
| #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ |
| #define CFG_I2C_SLAVE 0x7F |
| |
| #define CFG_I2C_EEPROM_ADDR 0x50 /* base address */ |
| #define CFG_I2C_EEPROM_ADDR_LEN 2 /* bytes of address */ |
| |
| #define CFG_EEPROM_PAGE_WRITE_BITS 5 /* 8 byte write page size */ |
| #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ |
| #define CFG_EEPROM_SIZE 0x2000 |
| |
| /*----------------------------------------------------------------------- |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * Please note that CFG_SDRAM_BASE _must_ start at 0 |
| */ |
| #define CFG_SDRAM_BASE 0x00000000 |
| #define CFG_FLASH_BASE 0xFFC00000 |
| #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ |
| #define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ |
| #define CFG_MONITOR_BASE (TEXT_BASE) |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /*----------------------------------------------------------------------- |
| * FLASH organization |
| */ |
| #define CFG_FLASH_CFI /* The flash is CFI compatible */ |
| #define CONFIG_FLASH_CFI_DRIVER |
| |
| #define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } |
| |
| #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ |
| |
| #define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| #define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ |
| #define CFG_FLASH_INCREMENT 0 /* there is only one bank */ |
| |
| #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ |
| #define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ |
| |
| #ifdef CFG_ENV_IS_IN_FLASH |
| #define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ |
| /* the environment is located before u-boot */ |
| #define CFG_ENV_ADDR (TEXT_BASE - CFG_ENV_SECT_SIZE) |
| |
| /* Address and size of Redundant Environment Sector */ |
| #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR - CFG_ENV_SECT_SIZE) |
| #define CFG_ENV_SIZE_REDUND (CFG_ENV_SECT_SIZE) |
| #endif |
| |
| #ifdef CONFIG_ENV_IS_IN_EEPROM |
| #define CFG_ENV_SIZE 0x400 /* Size of Environment vars */ |
| #define CFG_ENV_OFFSET 0x00000000 |
| #define CFG_ENABLE_CRC_16 1 /* Intrinsyc formatting used crc16 */ |
| #endif |
| |
| /* partly from PPCBoot */ |
| /* NAND */ |
| #define CONFIG_NAND |
| #ifdef CONFIG_NAND |
| #define CFG_NAND_BASE 0x60000000 |
| #define CFG_NAND_CS 10 /* our CS is GPIO10 */ |
| #define CFG_NAND_RDY 23 /* our RDY is GPIO23 */ |
| #define CFG_NAND_CE 24 /* our CE is GPIO24 */ |
| #define CFG_NAND_CLE 31 /* our CLE is GPIO31 */ |
| #define CFG_NAND_ALE 30 /* our ALE is GPIO30 */ |
| #define NAND_MAX_CHIPS 1 |
| #define CFG_MAX_NAND_DEVICE 1 |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for initial stack pointer and data area (in data cache) |
| */ |
| /* use on chip memory (OCM) for temperary stack until sdram is tested */ |
| /* see ./cpu/ppc4xx/start.S */ |
| #define CFG_TEMP_STACK_OCM 1 |
| |
| /* On Chip Memory location */ |
| #define CFG_OCM_DATA_ADDR 0xF8000000 |
| #define CFG_OCM_DATA_SIZE 0x1000 |
| #define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of OCM */ |
| #define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */ |
| |
| #define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ |
| #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) |
| #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET |
| |
| /*----------------------------------------------------------------------- |
| * External Bus Controller (EBC) Setup |
| * Taken from PPCBoot board/icecube/icecube.h |
| */ |
| |
| /* see ./cpu/ppc4xx/cpu_init.c ./cpu/ppc4xx/ndfc.c */ |
| #define CFG_EBC_PB0AP 0x04002480 |
| /* AMD NOR flash - this corresponds to FLASH_BASE so may be correct */ |
| #define CFG_EBC_PB0CR 0xFFC5A000 |
| #define CFG_EBC_PB1AP 0x04005480 |
| #define CFG_EBC_PB1CR 0x60018000 |
| #define CFG_EBC_PB2AP 0x00000000 |
| #define CFG_EBC_PB2CR 0x00000000 |
| #define CFG_EBC_PB3AP 0x00000000 |
| #define CFG_EBC_PB3CR 0x00000000 |
| #define CFG_EBC_PB4AP 0x00000000 |
| #define CFG_EBC_PB4CR 0x00000000 |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for GPIO setup (PPC405EP specific) |
| * |
| * Taken in part from PPCBoot board/icecube/icecube.h |
| */ |
| /* see ./cpu/ppc4xx/cpu_init.c ./cpu/ppc4xx/start.S */ |
| #define CFG_GPIO0_OSRH 0x55555550 |
| #define CFG_GPIO0_OSRL 0x00000110 |
| #define CFG_GPIO0_ISR1H 0x00000000 |
| #define CFG_GPIO0_ISR1L 0x15555445 |
| #define CFG_GPIO0_TSRH 0x00000000 |
| #define CFG_GPIO0_TSRL 0x00000000 |
| #define CFG_GPIO0_TCR 0xFFFF8097 |
| #define CFG_GPIO0_ODR 0x00000000 |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ |
| #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ |
| #endif |
| |
| /* ENVIRONMENT VARS */ |
| |
| #define CONFIG_IPADDR 192.168.1.67 |
| #define CONFIG_SERVERIP 192.168.1.50 |
| #define CONFIG_GATEWAYIP 192.168.1.1 |
| #define CONFIG_NETMASK 255.255.255.0 |
| #define CONFIG_LOADADDR 300000 |
| #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ |
| |
| /* pass open firmware flat tree */ |
| #define CONFIG_OF_LIBFDT 1 |
| |
| #endif /* __CONFIG_H */ |