include/configs/bcm_ns3.h - filogic/uboot - Gitiles

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2020 Broadcom.
  *
  */

 #ifndef __BCM_NS3_H
 #define __BCM_NS3_H

 #include <linux/sizes.h>

 #define CONFIG_HOSTNAME			"NS3"

 /* Physical Memory Map */
 #define V2M_BASE			0x80000000
 #define PHYS_SDRAM_1			V2M_BASE

 #define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
 #define CONFIG_SYS_LOAD_ADDR		(PHYS_SDRAM_1 + 0x80000)

 /*
  * Initial SP before reloaction is placed at end of first DRAM bank,
  * which is 0x1_0000_0000.
  * Just before re-loaction, new SP is updated and re-location happens.
  * So pointing the initial SP to end of 2GB DDR is not a problem
  */
 #define CONFIG_SYS_INIT_SP_ADDR		(PHYS_SDRAM_1 + 0x80000000)
 /* 12MB Malloc size */
 #define CONFIG_SYS_MALLOC_LEN		(SZ_8M + SZ_4M)

 /* console configuration */
 #define CONFIG_SYS_NS16550_CLK		25000000

 #define CONFIG_SYS_CBSIZE		SZ_1K
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
 					 sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS		64
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE

 /*
  * Increase max uncompressed/gunzip size, keeping size same as EMMC linux
  * partition.
  */
 #define CONFIG_SYS_BOOTM_LEN		0x01800000

 /* Env configuration */
 #define CONFIG_SYS_MMC_ENV_DEV		0
 #define CONFIG_SYS_MMC_ENV_PART		0

 /* Access eMMC Boot_1 and Boot_2 partitions */
 #define CONFIG_SUPPORT_EMMC_BOOT

 /* enable 64-bit PCI resources */
 #define CONFIG_SYS_PCI_64BIT		1

 #define CONSOLE_ARGS "console_args=console=ttyS0,115200n8\0"
 #define MAX_CPUS "max_cpus=maxcpus=8\0"
 #define OS_LOG_LEVEL "log_level=loglevel=7\0"
 #define EXTRA_ARGS "extra_args=earlycon=uart8250,mmio32,0x68A10000 " \
 		   "earlyelog=" __stringify(ELOG_AP_UART_LOG_BASE) ",0x10000 " \
 		   "crashkernel=512M reboot=w\0"

 #define PCIE_ARGS "pcie_args=pci=pcie_bus_safe pcie_ports=native vfio_pci.disable_idle_d3=1\0"

 #ifdef CONFIG_BCM_SF2_ETH
 #define ETH_ADDR "ethaddr=00:0A:F7:95:65:A4\0"
 #define NET_ARGS "bgmac_platform.ethaddr=${ethaddr} " \
 	"ip=${ipaddr}::${gatewayip}:${netmask}::${ethif}:off"
 #else
 #define ETH_ADDR
 #define NET_ARGS
 #endif

 #define RESERVED_MEM "reserved_mem=memmap=0xff000000$0x1000000\0"

 #define BASE_ARGS "${console_args} ${extra_args} ${pcie_args}" \
 		  " ${max_cpus}  ${log_level} ${reserved_mem}"
 #define SETBOOTARGS "setbootargs=setenv bootargs " BASE_ARGS " " NET_ARGS "\0"

 #define UPDATEME_FLASH_PARAMS "bcm_compat_level=4\0" \
 			      "bcm_need_recovery_rootfs=0\0" \
 			      "bcm_bl_flash_pending_rfs_imgs=0\0"

 #define KERNEL_LOADADDR_CFG \
 	"fit_image_loadaddr=0x90000000\0" \
 	"dtb_loadaddr=0x82000000\0"

 #define INITRD_ARGS "initrd_args=root=/dev/ram rw\0"
 #define INITRD_LOADADDR "initrd_loadaddr=0x92000000\0"
 #define INITRD_IMAGE "initrd_image=rootfs-lake-bcm958742t.cpio.gz\0"
 #define MMC_DEV "sd_device_number=0\0"
 #define EXEC_STATE "exec_state=normal\0"

 #define EXT4RD_ARGS "ext4rd_args="\
 	"root=/dev/mmcblk${sd_device_number}p${gpt_partition_entry} rw rootwait\0"

 #define WDT_CNTRL "wdt_enable=1\0" \
 		  "wdt_timeout_sec=0\0"

 #define ELOG_SETUP \
 	"mbox0_addr=0x66424024\0"\
 	"elog_setup="\
 	"if logsetup -s ${mbox0_addr}; then "\
 	"else "\
 		"echo ELOG is not supported by this version of the MCU patch.;"\
 		"exit;"\
 	"fi;"\
 	"if logsetup -c ${mbox0_addr}; then "\
 		"echo ELOG is ready;"\
 	"else "\
 		"echo ELOG is supported, but is not set up.;"\
 		"echo Getting setup file from the server ${serverip}...;"\
 		"if tftp ${tftp_dir}elog_src.txt; then "\
 			"echo Setting up ELOG. Please wait...;"\
 			"if logsetup ${loadaddr} ${mbox0_addr} ${filesize}; "\
 				"then "\
 			"else "\
 				"echo [logsetup] ERROR.;"\
 			"fi;"\
 			"if logsetup -c ${mbox0_addr}; then "\
 				"echo ELOG is READY.;"\
 			"else "\
 				"echo ELOG is NOT SET UP.;"\
 			"fi;"\
 		"else "\
 			"echo ELOG setup file is not available on the server.;"\
 		"fi;"\
 	"fi \0"

 /* eMMC partition for FIT images */
 #define FIT_MMC_PARTITION \
 	"fit_partitions=" \
 	"uuid_disk=${uuid_gpt_disk};" \
 	"name=env,size=512K,uuid=${uuid_gpt_env};" \
 	"name=Image_rsa.img,size=24MiB,uuid=${uuid_gpt_linux};" \
 	"name=Image1_rsa.img,size=24MiB,uuid=${uuid_gpt_linux1};" \
 	"name=Image2_rsa.img,size=24MiB,uuid=${uuid_gpt_linux2};" \
 	"name=nitro,size=8MiB,uuid=${uuid_gpt_nitro};" \
 	"name=recovery,size=940MiB,uuid=${uuid_gpt_recovery};" \
 	"name=rootfs,size=-,uuid=${uuid_gpt_prootfs}\0"

 #define QSPI_FLASH_NITRO_PARAMS \
 	"spi_nitro_img_bin_start=0x400000\0" \
 	"spi_nitro_img_bin_mirror_start=0x580000\0" \
 	"spi_nitro_bspd_cfg_start=0x700000\0" \
 	"spi_nitro_bspd_mirror_cfg_start=0x710000\0" \

 #define QSPI_ACCESS_ENABLE \
 	"qspi_access_en=" \
 	"mw 0x68a403e8 1;" \
 	"mw 0x68a403ec 1;" \
 	"mw 0x68a403f0 1;" \
 	"mw 0x68a403f4 1;" \
 	"mw 0x68a403f8 1;" \
 	"mw 0x68a403fc 1 \0"

 #define FUNC_QSPI_PROBE \
 	"func_qspi_probe="\
 	"if run qspi_access_en; then "\
 	"else "\
 		"echo ${errstr} run qspi_access_en ** FAILED **;"\
 		"exit;"\
 	"fi;"\
 	"if sf probe 0; then "\
 	"else "\
 		"echo echo ${errstr} sf probe command ** FAILED **;"\
 		"exit;"\
 	"fi \0"

 #define NITRO_FW_IMAGES \
 	"nitro_bin=nitro.img\0" \
 	"nitro_bspd_cfg=nitro_fb_bspd_config.bin\0"

 #define FASTBOOT_NITRO_SETUP \
 	"nitro_fastboot_type=1\0" \
 	"nitro_fastboot_secure=1\0" \
 	"nitro_fastboot_img_buffer=0\0" \
 	"nitro_fit_img_loc=0x90000000\0"

 #define FASTBOOT_SETUP \
 	"fastboot_nitro_setup=" \
 	"setenv errstr fastboot_setup;" \
 	"run func_qspi_probe;" \
 	/* first load header only */ \
 	"if sf read ${nitro_fit_img_loc} "\
 		   "${spi_nitro_img_bin_start} 0x18; then "\
 	"else "\
 		"echo [fastboot_nitro_setup] sf read "\
 		      "${spi_nitro_img_bin_start} ** FAILED **;"\
 		"exit;"\
 	"fi;"\
 	"if spi_nitro_images_addr ${nitro_fit_img_loc} "\
 				 "${spi_nitro_img_bin_start}; then "\
 	"else "\
 		 "echo [fastboot_nitro_setup] spi_nitro_images_addr "\
 		       "** FAILED **;"\
 		"exit;"\
 	"fi \0"

 #define CHECK_CHIMP_HS\
 	"check_chimp_hs=chimp_hs"\
 	"\0"

 #define FASTBOOT_NITRO "fastboot_nitro=chimp_ld_secure\0"

 #define FIT_IMAGE "fit_image=Image_rsa.img\0"
 #define BOOTCMD_MMC_FIT \
 	"bootcmd_mmc_fit="\
 	"mmc dev ${sd_device_number};"\
 	"if test $exec_state = normal; then " \
 		"setenv use_rootfs rootfs;"\
 	"else " \
 		"setenv use_rootfs recovery;"\
 	"fi;" \
 	"echo used filesystem :${use_rootfs};"\
 	"gpt setenv mmc ${sd_device_number} ${use_rootfs};"\
 	"setenv bootargs_fs ${setbootargs} ${ext4rd_args}; run bootargs_fs;"\
 	"gpt setenv mmc ${sd_device_number} ${fit_image};"\
 	"mmc read ${fit_image_loadaddr} ${gpt_partition_addr} "\
 	"${gpt_partition_size};"\
 	"bootm ${fit_image_loadaddr}\0"

 #define BOOTCMD_MMC_FITS \
 	"bootcmd_mmc_fits="\
 	"setenv mmc_fit0 " \
 	"'setenv fit_image Image_rsa.img; run bootcmd_mmc_fit';"\
 	"setenv mmc_fit1 " \
 	"'setenv fit_image Image1_rsa.img; run bootcmd_mmc_fit';"\
 	"setenv mmc_fit2 " \
 	"'setenv fit_image Image2_rsa.img; run bootcmd_mmc_fit';"\
 	"run mmc_fit0 || run mmc_fit1 || run mmc_fit2\0"

 #define USBDEV "usbdev=0\0"
 #define BOOTCMD_USB\
 	"bootcmd_usb="\
 	"setenv usb_image_loadaddr 90000000;"\
 	"setenv fit_image Image_rsa.img;"\
 	"setenv bootargs_fs ${setbootargs} ${initrd_args}; run bootargs_fs;"\
 	"if usb dev ${usbdev}; && usb start; then "\
 		"echo Booting from USB...;"\
 		"fatload usb ${usbdev} ${usb_image_loadaddr} ${fit_image};"\
 		"fatload usb ${usbdev} ${initrd_loadaddr} ${initrd_image};"\
 		"bootm ${usb_image_loadaddr} ${initrd_loadaddr}:${filesize};"\
 	"fi;"\
 	"\0"

 #define START_PCI\
 	"start_pci=pci e "\
 	"\0"

 #define BNXT_LOAD\
 	"bnxt_load=bnxt 0 probe "\
 	"\0"

 #define BOOTCMD_PXE\
 	"bootcmd_pxe="\
 	"run check_chimp_hs && "\
 	"run start_pci && "\
 	"run bnxt_load;"\
 	"setenv ethact bnxt_eth0;"\
 	"setenv autoload no;"\
 	"setenv bootargs_fs ${setbootargs} ${initrd_args}; run bootargs_fs;"\
 	"if dhcp; then "\
 		"setenv pxefile_addr_r ${loadaddr};"\
 		"if pxe get; then "\
 			"setenv ramdisk_addr_r ${initrd_loadaddr};"\
 			"setenv kernel_addr_r ${fit_image_loadaddr};"\
 			"pxe boot; "\
 		"fi;"\
 	"fi;"\
 	"\0"

 #define FLASH_PENDING_RFS_IMGS \
 	"flash_pending_rfs_imgs=" \
 	"if test $bcm_bl_flash_pending_rfs_imgs = 1; then " \
 		"if test $bl_flash_pending_rfs_imgs = rootfs; then " \
 			"dhcp;" \
 			"run mmc_flash_rootfs;" \
 		"fi;" \
 		"if test $bl_flash_pending_rfs_imgs = recovery; then " \
 			"dhcp;" \
 			"run mmc_flash_recovery;" \
 		"fi;" \
 		"setenv bl_flash_pending_rfs_imgs;" \
 	"fi; \0"

 #define CONFIG_BOOTCOMMAND "run flash_pending_rfs_imgs;" \
 			   "run fastboot_nitro && "\
 			   "run bootcmd_mmc_fits || "\
 			   "run bootcmd_usb || "\
 			   "run bootcmd_pxe"

 #define ARCH_ENV_SETTINGS \
 	CONSOLE_ARGS \
 	MAX_CPUS \
 	OS_LOG_LEVEL \
 	EXTRA_ARGS \
 	PCIE_ARGS \
 	ETH_ADDR \
 	RESERVED_MEM \
 	SETBOOTARGS \
 	UPDATEME_FLASH_PARAMS \
 	KERNEL_LOADADDR_CFG\
 	INITRD_ARGS \
 	INITRD_LOADADDR \
 	INITRD_IMAGE \
 	MMC_DEV \
 	EXEC_STATE \
 	EXT4RD_ARGS \
 	WDT_CNTRL \
 	ELOG_SETUP \
 	FIT_MMC_PARTITION \
 	QSPI_FLASH_NITRO_PARAMS \
 	QSPI_ACCESS_ENABLE \
 	FUNC_QSPI_PROBE \
 	NITRO_FW_IMAGES \
 	FASTBOOT_NITRO_SETUP \
 	FASTBOOT_SETUP \
 	CHECK_CHIMP_HS \
 	FASTBOOT_NITRO \
 	FIT_IMAGE \
 	BOOTCMD_MMC_FIT \
 	BOOTCMD_MMC_FITS \
 	USBDEV \
 	BOOTCMD_USB \
 	START_PCI \
 	BNXT_LOAD \
 	BOOTCMD_PXE \
 	FLASH_PENDING_RFS_IMGS

 #define CONFIG_EXTRA_ENV_SETTINGS \
 	ARCH_ENV_SETTINGS

 #endif /* __BCM_NS3_H */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* Copyright 2020 Broadcom.
	*
	*/

	#ifndef __BCM_NS3_H
	#define __BCM_NS3_H

	#include <linux/sizes.h>

	#define CONFIG_HOSTNAME "NS3"

	/* Physical Memory Map */
	#define V2M_BASE 0x80000000
	#define PHYS_SDRAM_1 V2M_BASE

	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
	#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x80000)

	/*
	* Initial SP before reloaction is placed at end of first DRAM bank,
	* which is 0x1_0000_0000.
	* Just before re-loaction, new SP is updated and re-location happens.
	* So pointing the initial SP to end of 2GB DDR is not a problem
	*/
	#define CONFIG_SYS_INIT_SP_ADDR (PHYS_SDRAM_1 + 0x80000000)
	/* 12MB Malloc size */
	#define CONFIG_SYS_MALLOC_LEN (SZ_8M + SZ_4M)

	/* console configuration */
	#define CONFIG_SYS_NS16550_CLK 25000000

	#define CONFIG_SYS_CBSIZE SZ_1K
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
	sizeof(CONFIG_SYS_PROMPT) + 16)
	#define CONFIG_SYS_MAXARGS 64
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE

	/*
	* Increase max uncompressed/gunzip size, keeping size same as EMMC linux
	* partition.
	*/
	#define CONFIG_SYS_BOOTM_LEN 0x01800000

	/* Env configuration */
	#define CONFIG_SYS_MMC_ENV_DEV 0
	#define CONFIG_SYS_MMC_ENV_PART 0

	/* Access eMMC Boot_1 and Boot_2 partitions */
	#define CONFIG_SUPPORT_EMMC_BOOT

	/* enable 64-bit PCI resources */
	#define CONFIG_SYS_PCI_64BIT 1

	#define CONSOLE_ARGS "console_args=console=ttyS0,115200n8\0"
	#define MAX_CPUS "max_cpus=maxcpus=8\0"
	#define OS_LOG_LEVEL "log_level=loglevel=7\0"
	#define EXTRA_ARGS "extra_args=earlycon=uart8250,mmio32,0x68A10000 " \
	"earlyelog=" __stringify(ELOG_AP_UART_LOG_BASE) ",0x10000 " \
	"crashkernel=512M reboot=w\0"

	#define PCIE_ARGS "pcie_args=pci=pcie_bus_safe pcie_ports=native vfio_pci.disable_idle_d3=1\0"

	#ifdef CONFIG_BCM_SF2_ETH
	#define ETH_ADDR "ethaddr=00:0A:F7:95:65:A4\0"
	#define NET_ARGS "bgmac_platform.ethaddr=${ethaddr} " \
	"ip=${ipaddr}::${gatewayip}:${netmask}::${ethif}:off"
	#else
	#define ETH_ADDR
	#define NET_ARGS
	#endif

	#define RESERVED_MEM "reserved_mem=memmap=0xff000000$0x1000000\0"

	#define BASE_ARGS "${console_args} ${extra_args} ${pcie_args}" \
	" ${max_cpus} ${log_level} ${reserved_mem}"
	#define SETBOOTARGS "setbootargs=setenv bootargs " BASE_ARGS " " NET_ARGS "\0"

	#define UPDATEME_FLASH_PARAMS "bcm_compat_level=4\0" \
	"bcm_need_recovery_rootfs=0\0" \
	"bcm_bl_flash_pending_rfs_imgs=0\0"

	#define KERNEL_LOADADDR_CFG \
	"fit_image_loadaddr=0x90000000\0" \
	"dtb_loadaddr=0x82000000\0"

	#define INITRD_ARGS "initrd_args=root=/dev/ram rw\0"
	#define INITRD_LOADADDR "initrd_loadaddr=0x92000000\0"
	#define INITRD_IMAGE "initrd_image=rootfs-lake-bcm958742t.cpio.gz\0"
	#define MMC_DEV "sd_device_number=0\0"
	#define EXEC_STATE "exec_state=normal\0"

	#define EXT4RD_ARGS "ext4rd_args="\
	"root=/dev/mmcblk${sd_device_number}p${gpt_partition_entry} rw rootwait\0"

	#define WDT_CNTRL "wdt_enable=1\0" \
	"wdt_timeout_sec=0\0"

	#define ELOG_SETUP \
	"mbox0_addr=0x66424024\0"\
	"elog_setup="\
	"if logsetup -s ${mbox0_addr}; then "\
	"else "\
	"echo ELOG is not supported by this version of the MCU patch.;"\
	"exit;"\
	"fi;"\
	"if logsetup -c ${mbox0_addr}; then "\
	"echo ELOG is ready;"\
	"else "\
	"echo ELOG is supported, but is not set up.;"\
	"echo Getting setup file from the server ${serverip}...;"\
	"if tftp ${tftp_dir}elog_src.txt; then "\
	"echo Setting up ELOG. Please wait...;"\
	"if logsetup ${loadaddr} ${mbox0_addr} ${filesize}; "\
	"then "\
	"else "\
	"echo [logsetup] ERROR.;"\
	"fi;"\
	"if logsetup -c ${mbox0_addr}; then "\
	"echo ELOG is READY.;"\
	"else "\
	"echo ELOG is NOT SET UP.;"\
	"fi;"\
	"else "\
	"echo ELOG setup file is not available on the server.;"\
	"fi;"\
	"fi \0"

	/* eMMC partition for FIT images */
	#define FIT_MMC_PARTITION \
	"fit_partitions=" \
	"uuid_disk=${uuid_gpt_disk};" \
	"name=env,size=512K,uuid=${uuid_gpt_env};" \
	"name=Image_rsa.img,size=24MiB,uuid=${uuid_gpt_linux};" \
	"name=Image1_rsa.img,size=24MiB,uuid=${uuid_gpt_linux1};" \
	"name=Image2_rsa.img,size=24MiB,uuid=${uuid_gpt_linux2};" \
	"name=nitro,size=8MiB,uuid=${uuid_gpt_nitro};" \
	"name=recovery,size=940MiB,uuid=${uuid_gpt_recovery};" \
	"name=rootfs,size=-,uuid=${uuid_gpt_prootfs}\0"

	#define QSPI_FLASH_NITRO_PARAMS \
	"spi_nitro_img_bin_start=0x400000\0" \
	"spi_nitro_img_bin_mirror_start=0x580000\0" \
	"spi_nitro_bspd_cfg_start=0x700000\0" \
	"spi_nitro_bspd_mirror_cfg_start=0x710000\0" \

	#define QSPI_ACCESS_ENABLE \
	"qspi_access_en=" \
	"mw 0x68a403e8 1;" \
	"mw 0x68a403ec 1;" \
	"mw 0x68a403f0 1;" \
	"mw 0x68a403f4 1;" \
	"mw 0x68a403f8 1;" \
	"mw 0x68a403fc 1 \0"

	#define FUNC_QSPI_PROBE \
	"func_qspi_probe="\
	"if run qspi_access_en; then "\
	"else "\
	"echo ${errstr} run qspi_access_en FAILED ;"\
	"exit;"\
	"fi;"\
	"if sf probe 0; then "\
	"else "\
	"echo echo ${errstr} sf probe command FAILED ;"\
	"exit;"\
	"fi \0"

	#define NITRO_FW_IMAGES \
	"nitro_bin=nitro.img\0" \
	"nitro_bspd_cfg=nitro_fb_bspd_config.bin\0"

	#define FASTBOOT_NITRO_SETUP \
	"nitro_fastboot_type=1\0" \
	"nitro_fastboot_secure=1\0" \
	"nitro_fastboot_img_buffer=0\0" \
	"nitro_fit_img_loc=0x90000000\0"

	#define FASTBOOT_SETUP \
	"fastboot_nitro_setup=" \
	"setenv errstr fastboot_setup;" \
	"run func_qspi_probe;" \
	/* first load header only */ \
	"if sf read ${nitro_fit_img_loc} "\
	"${spi_nitro_img_bin_start} 0x18; then "\
	"else "\
	"echo [fastboot_nitro_setup] sf read "\
	"${spi_nitro_img_bin_start} FAILED ;"\
	"exit;"\
	"fi;"\
	"if spi_nitro_images_addr ${nitro_fit_img_loc} "\
	"${spi_nitro_img_bin_start}; then "\
	"else "\
	"echo [fastboot_nitro_setup] spi_nitro_images_addr "\
	" FAILED ;"\
	"exit;"\
	"fi \0"

	#define CHECK_CHIMP_HS\
	"check_chimp_hs=chimp_hs"\
	"\0"

	#define FASTBOOT_NITRO "fastboot_nitro=chimp_ld_secure\0"

	#define FIT_IMAGE "fit_image=Image_rsa.img\0"
	#define BOOTCMD_MMC_FIT \
	"bootcmd_mmc_fit="\
	"mmc dev ${sd_device_number};"\
	"if test $exec_state = normal; then " \
	"setenv use_rootfs rootfs;"\
	"else " \
	"setenv use_rootfs recovery;"\
	"fi;" \
	"echo used filesystem :${use_rootfs};"\
	"gpt setenv mmc ${sd_device_number} ${use_rootfs};"\
	"setenv bootargs_fs ${setbootargs} ${ext4rd_args}; run bootargs_fs;"\
	"gpt setenv mmc ${sd_device_number} ${fit_image};"\
	"mmc read ${fit_image_loadaddr} ${gpt_partition_addr} "\
	"${gpt_partition_size};"\
	"bootm ${fit_image_loadaddr}\0"

	#define BOOTCMD_MMC_FITS \
	"bootcmd_mmc_fits="\
	"setenv mmc_fit0 " \
	"'setenv fit_image Image_rsa.img; run bootcmd_mmc_fit';"\
	"setenv mmc_fit1 " \
	"'setenv fit_image Image1_rsa.img; run bootcmd_mmc_fit';"\
	"setenv mmc_fit2 " \
	"'setenv fit_image Image2_rsa.img; run bootcmd_mmc_fit';"\
	"run mmc_fit0 \|\| run mmc_fit1 \|\| run mmc_fit2\0"

	#define USBDEV "usbdev=0\0"
	#define BOOTCMD_USB\
	"bootcmd_usb="\
	"setenv usb_image_loadaddr 90000000;"\
	"setenv fit_image Image_rsa.img;"\
	"setenv bootargs_fs ${setbootargs} ${initrd_args}; run bootargs_fs;"\
	"if usb dev ${usbdev}; && usb start; then "\
	"echo Booting from USB...;"\
	"fatload usb ${usbdev} ${usb_image_loadaddr} ${fit_image};"\
	"fatload usb ${usbdev} ${initrd_loadaddr} ${initrd_image};"\
	"bootm ${usb_image_loadaddr} ${initrd_loadaddr}:${filesize};"\
	"fi;"\
	"\0"

	#define START_PCI\
	"start_pci=pci e "\
	"\0"

	#define BNXT_LOAD\
	"bnxt_load=bnxt 0 probe "\
	"\0"

	#define BOOTCMD_PXE\
	"bootcmd_pxe="\
	"run check_chimp_hs && "\
	"run start_pci && "\
	"run bnxt_load;"\
	"setenv ethact bnxt_eth0;"\
	"setenv autoload no;"\
	"setenv bootargs_fs ${setbootargs} ${initrd_args}; run bootargs_fs;"\
	"if dhcp; then "\
	"setenv pxefile_addr_r ${loadaddr};"\
	"if pxe get; then "\
	"setenv ramdisk_addr_r ${initrd_loadaddr};"\
	"setenv kernel_addr_r ${fit_image_loadaddr};"\
	"pxe boot; "\
	"fi;"\
	"fi;"\
	"\0"

	#define FLASH_PENDING_RFS_IMGS \
	"flash_pending_rfs_imgs=" \
	"if test $bcm_bl_flash_pending_rfs_imgs = 1; then " \
	"if test $bl_flash_pending_rfs_imgs = rootfs; then " \
	"dhcp;" \
	"run mmc_flash_rootfs;" \
	"fi;" \
	"if test $bl_flash_pending_rfs_imgs = recovery; then " \
	"dhcp;" \
	"run mmc_flash_recovery;" \
	"fi;" \
	"setenv bl_flash_pending_rfs_imgs;" \
	"fi; \0"

	#define CONFIG_BOOTCOMMAND "run flash_pending_rfs_imgs;" \
	"run fastboot_nitro && "\
	"run bootcmd_mmc_fits \|\| "\
	"run bootcmd_usb \|\| "\
	"run bootcmd_pxe"

	#define ARCH_ENV_SETTINGS \
	CONSOLE_ARGS \
	MAX_CPUS \
	OS_LOG_LEVEL \
	EXTRA_ARGS \
	PCIE_ARGS \
	ETH_ADDR \
	RESERVED_MEM \
	SETBOOTARGS \
	UPDATEME_FLASH_PARAMS \
	KERNEL_LOADADDR_CFG\
	INITRD_ARGS \
	INITRD_LOADADDR \
	INITRD_IMAGE \
	MMC_DEV \
	EXEC_STATE \
	EXT4RD_ARGS \
	WDT_CNTRL \
	ELOG_SETUP \
	FIT_MMC_PARTITION \
	QSPI_FLASH_NITRO_PARAMS \
	QSPI_ACCESS_ENABLE \
	FUNC_QSPI_PROBE \
	NITRO_FW_IMAGES \
	FASTBOOT_NITRO_SETUP \
	FASTBOOT_SETUP \
	CHECK_CHIMP_HS \
	FASTBOOT_NITRO \
	FIT_IMAGE \
	BOOTCMD_MMC_FIT \
	BOOTCMD_MMC_FITS \
	USBDEV \
	BOOTCMD_USB \
	START_PCI \
	BNXT_LOAD \
	BOOTCMD_PXE \
	FLASH_PENDING_RFS_IMGS

	#define CONFIG_EXTRA_ENV_SETTINGS \
	ARCH_ENV_SETTINGS

	#endif /* __BCM_NS3_H */