| CONFIG_ARM=y |
| CONFIG_SKIP_LOWLEVEL_INIT=y |
| CONFIG_ARCH_AT91=y |
| CONFIG_SYS_TEXT_BASE=0x73f00000 |
| CONFIG_SYS_MALLOC_LEN=0x80000 |
| CONFIG_SYS_MALLOC_F_LEN=0x2000 |
| CONFIG_TARGET_PM9G45=y |
| CONFIG_ATMEL_LEGACY=y |
| CONFIG_NR_DRAM_BANKS=1 |
| CONFIG_DM_GPIO=y |
| CONFIG_DEFAULT_DEVICE_TREE="at91sam9m10g45ek" |
| CONFIG_DEBUG_UART_BASE=0xffffee00 |
| CONFIG_DEBUG_UART_CLOCK=132000000 |
| CONFIG_ENV_OFFSET_REDUND=0x100000 |
| CONFIG_DEBUG_UART=y |
| CONFIG_SYS_LOAD_ADDR=0x22000000 |
| CONFIG_NAND_BOOT=y |
| CONFIG_BOOTDELAY=3 |
| CONFIG_USE_BOOTARGS=y |
| CONFIG_BOOTARGS="fbcon=rotate:3 console=tty0 console=ttyS0,115200 root=/dev/mtdblock4 mtdparts=atmel_nand:128k(bootstrap)ro,256k(uboot)ro,1664k(env),2M(linux)ro,-(root) rw rootfstype=jffs2" |
| CONFIG_USE_BOOTCOMMAND=y |
| CONFIG_BOOTCOMMAND="nand read 0x70000000 0x200000 0x300000;bootm 0x70000000" |
| CONFIG_SYS_CONSOLE_IS_IN_ENV=y |
| # CONFIG_DISPLAY_BOARDINFO is not set |
| CONFIG_HUSH_PARSER=y |
| CONFIG_SYS_PROMPT="U-Boot> " |
| # CONFIG_CMD_BDI is not set |
| CONFIG_CMD_BOOTZ=y |
| # CONFIG_CMD_IMI is not set |
| # CONFIG_CMD_FLASH is not set |
| # CONFIG_CMD_LOADS is not set |
| CONFIG_CMD_MMC=y |
| CONFIG_CMD_NAND=y |
| CONFIG_CMD_USB=y |
| # CONFIG_CMD_SETEXPR is not set |
| CONFIG_CMD_DHCP=y |
| CONFIG_BOOTP_BOOTFILESIZE=y |
| CONFIG_CMD_MII=y |
| CONFIG_CMD_PING=y |
| CONFIG_CMD_FAT=y |
| CONFIG_OF_CONTROL=y |
| CONFIG_ENV_IS_IN_NAND=y |
| CONFIG_SYS_REDUNDAND_ENVIRONMENT=y |
| CONFIG_SYS_RELOC_GD_ENV_ADDR=y |
| CONFIG_NET_RANDOM_ETHADDR=y |
| CONFIG_DM=y |
| CONFIG_CLK=y |
| CONFIG_CLK_AT91=y |
| CONFIG_AT91_GPIO=y |
| CONFIG_GENERIC_ATMEL_MCI=y |
| CONFIG_MTD=y |
| CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT=y |
| # CONFIG_SYS_NAND_USE_FLASH_BBT is not set |
| CONFIG_NAND_ATMEL=y |
| CONFIG_DM_ETH=y |
| CONFIG_MACB=y |
| CONFIG_PINCTRL=y |
| CONFIG_PINCTRL_AT91=y |
| CONFIG_DM_SERIAL=y |
| CONFIG_DEBUG_UART_ANNOUNCE=y |
| CONFIG_ATMEL_USART=y |
| CONFIG_TIMER=y |
| CONFIG_ATMEL_PIT_TIMER=y |
| CONFIG_USB=y |
| CONFIG_USB_EHCI_HCD=y |
| CONFIG_USB_STORAGE=y |