| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright 2021 Gateworks Corporation |
| */ |
| |
| #include <common.h> |
| #include <command.h> |
| #include <hang.h> |
| #include <hexdump.h> |
| #include <i2c.h> |
| #include <linux/delay.h> |
| #include <dm/uclass.h> |
| |
| #include "gsc.h" |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| struct venice_board_info som_info; |
| struct venice_board_info base_info; |
| char venice_model[32]; |
| uint32_t venice_serial; |
| |
| /* return a mac address from EEPROM info */ |
| int gsc_getmac(int index, uint8_t *address) |
| { |
| int i, j; |
| u32 maclow, machigh; |
| u64 mac; |
| |
| j = 0; |
| if (som_info.macno) { |
| maclow = som_info.mac[5]; |
| maclow |= som_info.mac[4] << 8; |
| maclow |= som_info.mac[3] << 16; |
| maclow |= som_info.mac[2] << 24; |
| machigh = som_info.mac[1]; |
| machigh |= som_info.mac[0] << 8; |
| mac = machigh; |
| mac <<= 32; |
| mac |= maclow; |
| for (i = 0; i < som_info.macno; i++, j++) { |
| if (index == j) |
| goto out; |
| } |
| } |
| |
| maclow = base_info.mac[5]; |
| maclow |= base_info.mac[4] << 8; |
| maclow |= base_info.mac[3] << 16; |
| maclow |= base_info.mac[2] << 24; |
| machigh = base_info.mac[1]; |
| machigh |= base_info.mac[0] << 8; |
| mac = machigh; |
| mac <<= 32; |
| mac |= maclow; |
| for (i = 0; i < base_info.macno; i++, j++) { |
| if (index == j) |
| goto out; |
| } |
| |
| return -EINVAL; |
| |
| out: |
| mac += i; |
| address[0] = (mac >> 40) & 0xff; |
| address[1] = (mac >> 32) & 0xff; |
| address[2] = (mac >> 24) & 0xff; |
| address[3] = (mac >> 16) & 0xff; |
| address[4] = (mac >> 8) & 0xff; |
| address[5] = (mac >> 0) & 0xff; |
| |
| return 0; |
| } |
| |
| /* System Controller registers */ |
| enum { |
| GSC_SC_CTRL0 = 0, |
| GSC_SC_CTRL1 = 1, |
| GSC_SC_STATUS = 10, |
| GSC_SC_FWCRC = 12, |
| GSC_SC_FWVER = 14, |
| GSC_SC_WP = 15, |
| GSC_SC_RST_CAUSE = 16, |
| GSC_SC_THERM_PROTECT = 19, |
| }; |
| |
| /* System Controller Control1 bits */ |
| enum { |
| GSC_SC_CTRL1_WDTIME = 4, /* 1 = 60s timeout, 0 = 30s timeout */ |
| GSC_SC_CTRL1_WDEN = 5, /* 1 = enable, 0 = disable */ |
| GSC_SC_CTRL1_BOOT_CHK = 6, /* 1 = enable alt boot check */ |
| GSC_SC_CTRL1_WDDIS = 7, /* 1 = disable boot watchdog */ |
| }; |
| |
| /* System Controller Interrupt bits */ |
| enum { |
| GSC_SC_IRQ_PB = 0, /* Pushbutton switch */ |
| GSC_SC_IRQ_SECURE = 1, /* Secure Key erase operation complete */ |
| GSC_SC_IRQ_EEPROM_WP = 2, /* EEPROM write violation */ |
| GSC_SC_IRQ_GPIO = 4, /* GPIO change */ |
| GSC_SC_IRQ_TAMPER = 5, /* Tamper detect */ |
| GSC_SC_IRQ_WATCHDOG = 6, /* Watchdog trip */ |
| GSC_SC_IRQ_PBLONG = 7, /* Pushbutton long hold */ |
| }; |
| |
| /* System Controller WP bits */ |
| enum { |
| GSC_SC_WP_ALL = 0, /* Write Protect All EEPROM regions */ |
| GSC_SC_WP_BOARDINFO = 1, /* Write Protect Board Info region */ |
| }; |
| |
| /* System Controller Reset Cause */ |
| enum { |
| GSC_SC_RST_CAUSE_VIN = 0, |
| GSC_SC_RST_CAUSE_PB = 1, |
| GSC_SC_RST_CAUSE_WDT = 2, |
| GSC_SC_RST_CAUSE_CPU = 3, |
| GSC_SC_RST_CAUSE_TEMP_LOCAL = 4, |
| GSC_SC_RST_CAUSE_TEMP_REMOTE = 5, |
| GSC_SC_RST_CAUSE_SLEEP = 6, |
| GSC_SC_RST_CAUSE_BOOT_WDT = 7, |
| GSC_SC_RST_CAUSE_BOOT_WDT_MAN = 8, |
| GSC_SC_RST_CAUSE_SOFT_PWR = 9, |
| GSC_SC_RST_CAUSE_MAX = 10, |
| }; |
| |
| #include <dm/device.h> |
| static struct udevice *gsc_get_dev(int busno, int slave) |
| { |
| struct udevice *dev, *bus; |
| int ret; |
| |
| ret = uclass_get_device_by_seq(UCLASS_I2C, busno, &bus); |
| if (ret) { |
| printf("GSC : failed I2C%d probe: %d\n", busno, ret); |
| return NULL; |
| } |
| ret = dm_i2c_probe(bus, slave, 0, &dev); |
| if (ret) |
| return NULL; |
| |
| return dev; |
| } |
| |
| static int gsc_read_eeprom(int bus, int slave, int alen, struct venice_board_info *info) |
| { |
| int i; |
| int chksum; |
| unsigned char *buf = (unsigned char *)info; |
| struct udevice *dev; |
| int ret; |
| |
| /* probe device */ |
| dev = gsc_get_dev(bus, slave); |
| if (!dev) { |
| if (slave == GSC_EEPROM_ADDR) |
| puts("ERROR: Failed to probe EEPROM\n"); |
| return -ENODEV; |
| } |
| |
| /* read eeprom config section */ |
| memset(info, 0, sizeof(*info)); |
| ret = i2c_set_chip_offset_len(dev, alen); |
| if (ret) { |
| puts("EEPROM: Failed to set alen\n"); |
| return ret; |
| } |
| ret = dm_i2c_read(dev, 0x00, buf, sizeof(*info)); |
| if (ret) { |
| if (slave == GSC_EEPROM_ADDR) |
| printf("EEPROM: Failed to read EEPROM\n"); |
| return ret; |
| } |
| |
| /* validate checksum */ |
| for (chksum = 0, i = 0; i < (int)sizeof(*info) - 2; i++) |
| chksum += buf[i]; |
| if ((info->chksum[0] != chksum >> 8) || |
| (info->chksum[1] != (chksum & 0xff))) { |
| printf("EEPROM: I2C%d@0x%02x: Invalid Checksum\n", bus, slave); |
| print_hex_dump_bytes("", DUMP_PREFIX_NONE, buf, sizeof(*info)); |
| memset(info, 0, sizeof(*info)); |
| return -EINVAL; |
| } |
| |
| /* sanity check valid model */ |
| if (info->model[0] != 'G' || info->model[1] != 'W') { |
| printf("EEPROM: I2C%d@0x%02x: Invalid Model in EEPROM\n", bus, slave); |
| print_hex_dump_bytes("", DUMP_PREFIX_NONE, buf, sizeof(*info)); |
| memset(info, 0, sizeof(*info)); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static const char *gsc_get_rst_cause(struct udevice *dev) |
| { |
| static char str[64]; |
| static const char * const names[] = { |
| "VIN", |
| "PB", |
| "WDT", |
| "CPU", |
| "TEMP_L", |
| "TEMP_R", |
| "SLEEP", |
| "BOOT_WDT1", |
| "BOOT_WDT2", |
| "SOFT_PWR", |
| }; |
| unsigned char reg; |
| |
| /* reset cause */ |
| str[0] = 0; |
| if (!dm_i2c_read(dev, GSC_SC_RST_CAUSE, ®, 1)) { |
| if (reg < ARRAY_SIZE(names)) |
| sprintf(str, "%s", names[reg]); |
| else |
| sprintf(str, "0x%02x", reg); |
| } |
| |
| /* thermal protection */ |
| if (!dm_i2c_read(dev, GSC_SC_THERM_PROTECT, ®, 1)) { |
| strcat(str, " Thermal Protection "); |
| if (reg & BIT(0)) |
| strcat(str, "Enabled"); |
| else |
| strcat(str, "Disabled"); |
| } |
| |
| return str; |
| } |
| |
| /* display hardware monitor ADC channels */ |
| int gsc_hwmon(void) |
| { |
| const void *fdt = gd->fdt_blob; |
| struct udevice *dev; |
| int node, reg, mode, len, val, offset; |
| const char *label; |
| u8 buf[2]; |
| int ret; |
| |
| node = fdt_node_offset_by_compatible(fdt, -1, "gw,gsc-adc"); |
| if (node <= 0) |
| return node; |
| |
| /* probe device */ |
| dev = gsc_get_dev(GSC_BUSNO, GSC_HWMON_ADDR); |
| if (!dev) { |
| puts("ERROR: Failed to probe GSC HWMON\n"); |
| return -ENODEV; |
| } |
| |
| /* iterate over hwmon nodes */ |
| node = fdt_first_subnode(fdt, node); |
| while (node > 0) { |
| reg = fdtdec_get_int(fdt, node, "reg", -1); |
| mode = fdtdec_get_int(fdt, node, "gw,mode", -1); |
| offset = fdtdec_get_int(fdt, node, "gw,voltage-offset-microvolt", 0); |
| label = fdt_stringlist_get(fdt, node, "label", 0, NULL); |
| |
| if ((reg == -1) || (mode == -1) || !label) |
| printf("invalid dt:%s\n", fdt_get_name(fdt, node, NULL)); |
| |
| memset(buf, 0, sizeof(buf)); |
| ret = dm_i2c_read(dev, reg, buf, sizeof(buf)); |
| if (ret) { |
| printf("i2c error: %d\n", ret); |
| continue; |
| } |
| val = buf[0] | buf[1] << 8; |
| if (val >= 0) { |
| const u32 *div; |
| int r[2]; |
| |
| switch (mode) { |
| case 0: /* temperature (C*10) */ |
| if (val > 0x8000) |
| val -= 0xffff; |
| printf("%-8s: %d.%ldC\n", label, val / 10, abs(val % 10)); |
| break; |
| case 1: /* prescaled voltage */ |
| if (val != 0xffff) |
| printf("%-8s: %d.%03dV\n", label, val / 1000, val % 1000); |
| break; |
| case 2: /* scaled based on ref volt and resolution */ |
| val *= 2500; |
| val /= 1 << 12; |
| |
| /* apply pre-scaler voltage divider */ |
| div = fdt_getprop(fdt, node, "gw,voltage-divider-ohms", &len); |
| if (div && (len == sizeof(uint32_t) * 2)) { |
| r[0] = fdt32_to_cpu(div[0]); |
| r[1] = fdt32_to_cpu(div[1]); |
| if (r[0] && r[1]) { |
| val *= (r[0] + r[1]); |
| val /= r[1]; |
| } |
| } |
| |
| /* adjust by offset */ |
| val += (offset / 1000); |
| |
| printf("%-8s: %d.%03dV\n", label, val / 1000, val % 1000); |
| break; |
| } |
| } |
| node = fdt_next_subnode(fdt, node); |
| } |
| |
| return 0; |
| } |
| |
| /* determine BOM revision from model */ |
| int get_bom_rev(const char *str) |
| { |
| int rev_bom = 0; |
| int i; |
| |
| for (i = strlen(str) - 1; i > 0; i--) { |
| if (str[i] == '-') |
| break; |
| if (str[i] >= '1' && str[i] <= '9') { |
| rev_bom = str[i] - '0'; |
| break; |
| } |
| } |
| return rev_bom; |
| } |
| |
| /* determine PCB revision from model */ |
| char get_pcb_rev(const char *str) |
| { |
| char rev_pcb = 'A'; |
| int i; |
| |
| for (i = strlen(str) - 1; i > 0; i--) { |
| if (str[i] == '-') |
| break; |
| if (str[i] >= 'A') { |
| rev_pcb = str[i]; |
| break; |
| } |
| } |
| return rev_pcb; |
| } |
| |
| /* |
| * get dt name based on model and detail level: |
| * |
| * For boards that are a combination of a SoM plus a Baseboard: |
| * Venice SoM part numbers are GW70xx where xx is: |
| * 7000-7019: same PCB with som dt of '0x' |
| * 7020-7039: same PCB with som dt of '2x' |
| * 7040-7059: same PCB with som dt of '4x' |
| * 7060-7079: same PCB with som dt of '6x' |
| * 7080-7099: same PCB with som dt of '8x' |
| * Venice Baseboard part numbers are GW7xxx where xxx is: |
| * 7100-7199: same PCB with base dt of '71xx' |
| * 7200-7299: same PCB with base dt of '72xx' |
| * 7300-7399: same PCB with base dt of '73xx' |
| * 7400-7499: same PCB with base dt of '74xx' |
| * 7500-7599: same PCB with base dt of '75xx' |
| * 7600-7699: same PCB with base dt of '76xx' |
| * 7700-7799: same PCB with base dt of '77xx' |
| * 7800-7899: same PCB with base dt of '78xx' |
| * DT name is comprised of: |
| * gw<base dt>-<som dt>-[base-pcb-rev][base-bom-rev][som-pcb-rev][som-bom-rev] |
| * |
| * For board models from 7900-7999 each PCB is unique with its own dt: |
| * DT name is comprised: |
| * gw<model>-[pcb-rev][bom-rev] |
| * |
| */ |
| #define snprintfcat(dest, sz, fmt, ...) \ |
| snprintf((dest) + strlen(dest), (sz) - strlen(dest), fmt, ##__VA_ARGS__) |
| const char *gsc_get_dtb_name(int level, char *buf, int sz) |
| { |
| const char *pre = "imx8mm-venice-gw"; |
| int model, rev_pcb, rev_bom; |
| |
| model = ((som_info.model[2] - '0') * 1000) |
| + ((som_info.model[3] - '0') * 100) |
| + ((som_info.model[4] - '0') * 10) |
| + (som_info.model[5] - '0'); |
| rev_pcb = tolower(get_pcb_rev(som_info.model)); |
| rev_bom = get_bom_rev(som_info.model); |
| |
| /* som + baseboard*/ |
| if (base_info.model[0]) { |
| /* baseboard id: 7100-7199->71; 7200-7299->72; etc */ |
| int base = ((base_info.model[2] - '0') * 10) + (base_info.model[3] - '0'); |
| /* som id: 7000-7019->1; 7020-7039->2; etc */ |
| int som = ((model % 100) / 20) * 2; |
| int rev_base_pcb = tolower(get_pcb_rev(base_info.model)); |
| int rev_base_bom = get_bom_rev(base_info.model); |
| |
| snprintf(buf, sz, "%s%2dxx-%dx", pre, base, som); |
| switch (level) { |
| case 0: /* full model (ie gw73xx-0x-a1a1) */ |
| if (rev_base_bom) |
| snprintfcat(buf, sz, "-%c%d", rev_base_pcb, rev_base_bom); |
| else |
| snprintfcat(buf, sz, "-%c", rev_base_pcb); |
| if (rev_bom) |
| snprintfcat(buf, sz, "%c%d", rev_pcb, rev_bom); |
| else |
| snprintfcat(buf, sz, "%c", rev_pcb); |
| break; |
| case 1: /* don't care about SoM revision */ |
| if (rev_base_bom) |
| snprintfcat(buf, sz, "-%c%d", rev_base_pcb, rev_base_bom); |
| else |
| snprintfcat(buf, sz, "-%c", rev_base_pcb); |
| snprintfcat(buf, sz, "xx"); |
| break; |
| case 2: /* don't care about baseboard revision */ |
| snprintfcat(buf, sz, "-xx"); |
| if (rev_bom) |
| snprintfcat(buf, sz, "%c%d", rev_pcb, rev_bom); |
| else |
| snprintfcat(buf, sz, "%c", rev_pcb); |
| break; |
| case 3: /* don't care about SoM/baseboard revision */ |
| break; |
| default: |
| return NULL; |
| } |
| } else { |
| snprintf(buf, sz, "%s%04d", pre, model); |
| switch (level) { |
| case 0: /* full model wth PCB and BOM revision first (ie gw7901-a1) */ |
| if (rev_bom) |
| snprintfcat(buf, sz, "-%c%d", rev_pcb, rev_bom); |
| else |
| snprintfcat(buf, sz, "-%c", rev_pcb); |
| break; |
| case 1: /* don't care about BOM revision */ |
| snprintfcat(buf, sz, "-%c", rev_pcb); |
| break; |
| case 2: /* don't care about PCB or BOM revision */ |
| break; |
| default: |
| return NULL; |
| } |
| } |
| |
| return buf; |
| } |
| |
| static int gsc_read(void) |
| { |
| char rev_pcb; |
| int rev_bom; |
| int ret; |
| |
| ret = gsc_read_eeprom(GSC_BUSNO, GSC_EEPROM_ADDR, 1, &som_info); |
| if (ret) { |
| memset(&som_info, 0, sizeof(som_info)); |
| return ret; |
| } |
| |
| /* read optional baseboard EEPROM */ |
| gsc_read_eeprom(BASEBOARD_EEPROM_BUSNO, BASEBOARD_EEPROM_ADDR, |
| 2, &base_info); |
| |
| /* create model strings */ |
| if (base_info.model[0]) { |
| sprintf(venice_model, "GW%c%c%c%c-%c%c-", |
| som_info.model[2], /* family */ |
| base_info.model[3], /* baseboard */ |
| base_info.model[4], base_info.model[5], /* subload of baseboard */ |
| som_info.model[4], som_info.model[5]); /* last 2digits of SOM */ |
| |
| /* baseboard revision */ |
| rev_pcb = get_pcb_rev(base_info.model); |
| rev_bom = get_bom_rev(base_info.model); |
| if (rev_bom) |
| sprintf(venice_model + strlen(venice_model), "%c%d", rev_pcb, rev_bom); |
| else |
| sprintf(venice_model + strlen(venice_model), "%c", rev_pcb); |
| /* som revision */ |
| rev_pcb = get_pcb_rev(som_info.model); |
| rev_bom = get_bom_rev(som_info.model); |
| if (rev_bom) |
| sprintf(venice_model + strlen(venice_model), "%c%d", rev_pcb, rev_bom); |
| else |
| sprintf(venice_model + strlen(venice_model), "%c", rev_pcb); |
| } else { |
| strcpy(venice_model, som_info.model); |
| } |
| venice_serial = som_info.serial; |
| |
| return 0; |
| } |
| |
| static int gsc_info(int verbose) |
| { |
| struct udevice *dev; |
| unsigned char buf[16]; |
| |
| printf("Model : %s\n", venice_model); |
| printf("Serial : %d\n", som_info.serial); |
| printf("MFGDate : %02x-%02x-%02x%02x\n", |
| som_info.mfgdate[0], som_info.mfgdate[1], |
| som_info.mfgdate[2], som_info.mfgdate[3]); |
| if (base_info.model[0] && verbose > 1) { |
| printf("SOM : %s %d %02x-%02x-%02x%02x\n", |
| som_info.model, som_info.serial, |
| som_info.mfgdate[0], som_info.mfgdate[1], |
| som_info.mfgdate[2], som_info.mfgdate[3]); |
| printf("BASE : %s %d %02x-%02x-%02x%02x\n", |
| base_info.model, base_info.serial, |
| base_info.mfgdate[0], base_info.mfgdate[1], |
| base_info.mfgdate[2], base_info.mfgdate[3]); |
| } |
| |
| /* Display RTC */ |
| puts("RTC : "); |
| dev = gsc_get_dev(GSC_BUSNO, GSC_RTC_ADDR); |
| if (!dev) { |
| puts("Failed to probe GSC RTC\n"); |
| } else { |
| dm_i2c_read(dev, 0, buf, 6); |
| printf("%d\n", buf[0] | buf[1] << 8 | buf[2] << 16 | buf[3] << 24); |
| } |
| |
| /* Display hwmon */ |
| gsc_hwmon(); |
| |
| return 0; |
| } |
| |
| int gsc_init(int quiet) |
| { |
| unsigned char buf[16]; |
| struct udevice *dev; |
| int ret; |
| |
| /* |
| * On a board with a missing/depleted backup battery for GSC, the |
| * board may be ready to probe the GSC before its firmware is |
| * running. We will wait here indefinately for the GSC/EEPROM. |
| */ |
| while (1) { |
| /* probe device */ |
| dev = gsc_get_dev(GSC_BUSNO, GSC_SC_ADDR); |
| if (dev) |
| break; |
| mdelay(1); |
| } |
| |
| ret = dm_i2c_read(dev, 0, buf, sizeof(buf)); |
| if (ret) { |
| puts("ERROR: Failed reading GSC\n"); |
| return ret; |
| } |
| gsc_read(); |
| |
| /* banner */ |
| if (!quiet) { |
| printf("GSC : v%d 0x%04x", buf[GSC_SC_FWVER], |
| buf[GSC_SC_FWCRC] | buf[GSC_SC_FWCRC + 1] << 8); |
| printf(" RST:%s", gsc_get_rst_cause(dev)); |
| printf("\n"); |
| gsc_info(1); |
| } |
| |
| if (ret) |
| hang(); |
| |
| return ((16 << som_info.sdram_size) / 1024); |
| } |
| |
| const char *gsc_get_model(void) |
| { |
| return venice_model; |
| } |
| |
| uint32_t gsc_get_serial(void) |
| { |
| return venice_serial; |
| } |
| |
| #if !(IS_ENABLED(CONFIG_SPL_BUILD)) |
| static int gsc_sleep(unsigned long secs) |
| { |
| unsigned char reg; |
| struct udevice *dev; |
| int ret; |
| |
| /* probe device */ |
| dev = gsc_get_dev(GSC_BUSNO, GSC_SC_ADDR); |
| if (!dev) |
| return -ENODEV; |
| |
| printf("GSC Sleeping for %ld seconds\n", secs); |
| reg = (secs >> 24) & 0xff; |
| ret = dm_i2c_write(dev, 9, ®, 1); |
| if (ret) |
| goto err; |
| reg = (secs >> 16) & 0xff; |
| ret = dm_i2c_write(dev, 8, ®, 1); |
| if (ret) |
| goto err; |
| reg = (secs >> 8) & 0xff; |
| ret = dm_i2c_write(dev, 7, ®, 1); |
| if (ret) |
| goto err; |
| reg = secs & 0xff; |
| ret = dm_i2c_write(dev, 6, ®, 1); |
| if (ret) |
| goto err; |
| ret = dm_i2c_read(dev, GSC_SC_CTRL1, ®, 1); |
| if (ret) |
| goto err; |
| reg |= (1 << 2); |
| ret = dm_i2c_write(dev, GSC_SC_CTRL1, ®, 1); |
| if (ret) |
| goto err; |
| reg &= ~(1 << 2); |
| reg |= 0x3; |
| ret = dm_i2c_write(dev, GSC_SC_CTRL1, ®, 1); |
| if (ret) |
| goto err; |
| |
| return 0; |
| |
| err: |
| printf("i2c error\n"); |
| return ret; |
| } |
| |
| static int gsc_boot_wd_disable(void) |
| { |
| u8 reg; |
| struct udevice *dev; |
| int ret; |
| |
| /* probe device */ |
| dev = gsc_get_dev(GSC_BUSNO, GSC_SC_ADDR); |
| if (!dev) |
| return -ENODEV; |
| |
| ret = dm_i2c_read(dev, GSC_SC_CTRL1, ®, 1); |
| if (ret) |
| goto err; |
| reg |= (1 << GSC_SC_CTRL1_WDDIS); |
| reg &= ~(1 << GSC_SC_CTRL1_BOOT_CHK); |
| ret = dm_i2c_write(dev, GSC_SC_CTRL1, ®, 1); |
| if (ret) |
| goto err; |
| puts("GSC : boot watchdog disabled\n"); |
| |
| return 0; |
| |
| err: |
| printf("i2c error"); |
| return ret; |
| } |
| |
| static int do_gsc(struct cmd_tbl *cmdtp, int flag, int argc, char * const argv[]) |
| { |
| if (argc < 2) |
| return gsc_info(2); |
| |
| if (strcasecmp(argv[1], "sleep") == 0) { |
| if (argc < 3) |
| return CMD_RET_USAGE; |
| if (!gsc_sleep(dectoul(argv[2], NULL))) |
| return CMD_RET_SUCCESS; |
| } else if (strcasecmp(argv[1], "hwmon") == 0) { |
| if (!gsc_hwmon()) |
| return CMD_RET_SUCCESS; |
| } else if (strcasecmp(argv[1], "wd-disable") == 0) { |
| if (!gsc_boot_wd_disable()) |
| return CMD_RET_SUCCESS; |
| } |
| |
| return CMD_RET_USAGE; |
| } |
| |
| U_BOOT_CMD(gsc, 4, 1, do_gsc, "Gateworks System Controller", |
| "[sleep <secs>]|[hwmon]|[wd-disable]\n"); |
| #endif |