arch/arm/mach-meson/board-gx.c - filogic/uboot - Gitiles

 // SPDX-License-Identifier: GPL-2.0+
 /*
  * (C) Copyright 2016 Beniamino Galvani <b.galvani@gmail.com>
  * (C) Copyright 2018 Neil Armstrong <narmstrong@baylibre.com>
  */

 #include <common.h>
 #include <init.h>
 #include <net.h>
 #include <asm/arch/boot.h>
 #include <asm/arch/eth.h>
 #include <asm/arch/gx.h>
 #include <asm/arch/mem.h>
 #include <asm/arch/meson-vpu.h>
 #include <asm/global_data.h>
 #include <asm/io.h>
 #include <asm/armv8/mmu.h>
 #include <linux/sizes.h>
 #include <usb.h>
 #include <linux/usb/otg.h>
 #include <asm/arch/usb-gx.h>
 #include <usb/dwc2_udc.h>
 #include <clk.h>
 #include <phy.h>

 DECLARE_GLOBAL_DATA_PTR;

 int meson_get_boot_device(void)
 {
 	return readl(GX_AO_SEC_GP_CFG0) & GX_AO_BOOT_DEVICE;
 }

 /* Configure the reserved memory zones exported by the secure registers
  * into EFI and DTB reserved memory entries.
  */
 void meson_init_reserved_memory(void *fdt)
 {
 	u64 bl31_size, bl31_start;
 	u64 bl32_size, bl32_start;
 	u32 reg;

 	/*
 	 * Get ARM Trusted Firmware reserved memory zones in :
 	 * - AO_SEC_GP_CFG3: bl32 & bl31 size in KiB, can be 0
 	 * - AO_SEC_GP_CFG5: bl31 physical start address, can be NULL
 	 * - AO_SEC_GP_CFG4: bl32 physical start address, can be NULL
 	 */
 	reg = readl(GX_AO_SEC_GP_CFG3);

 	bl31_size = ((reg & GX_AO_BL31_RSVMEM_SIZE_MASK)
 			>> GX_AO_BL31_RSVMEM_SIZE_SHIFT) * SZ_1K;
 	bl32_size = (reg & GX_AO_BL32_RSVMEM_SIZE_MASK) * SZ_1K;

 	bl31_start = readl(GX_AO_SEC_GP_CFG5);
 	bl32_start = readl(GX_AO_SEC_GP_CFG4);

 	/*
 	 * Early Meson GX Firmware revisions did not provide the reserved
 	 * memory zones in the registers, keep fixed memory zone handling.
 	 */
 	if (IS_ENABLED(CONFIG_MESON_GX) &&
 	    !reg && !bl31_start && !bl32_start) {
 		bl31_start = 0x10000000;
 		bl31_size = 0x200000;
 	}

 	/* Add first 16MiB reserved zone */
 	meson_board_add_reserved_memory(fdt, 0, GX_FIRMWARE_MEM_SIZE);

 	/* Add BL31 reserved zone */
 	if (bl31_start && bl31_size)
 		meson_board_add_reserved_memory(fdt, bl31_start, bl31_size);

 	/* Add BL32 reserved zone */
 	if (bl32_start && bl32_size)
 		meson_board_add_reserved_memory(fdt, bl32_start, bl32_size);

 #if defined(CONFIG_VIDEO_MESON)
 	meson_vpu_rsv_fb(fdt);
 #endif
 }

 phys_size_t get_effective_memsize(void)
 {
 	/* Size is reported in MiB, convert it in bytes */
 	return ((readl(GX_AO_SEC_GP_CFG0) & GX_AO_MEM_SIZE_MASK)
 			>> GX_AO_MEM_SIZE_SHIFT) * SZ_1M;
 }

 static struct mm_region gx_mem_map[] = {
 	{
 		.virt = 0x0UL,
 		.phys = 0x0UL,
 		.size = 0xc0000000UL,
 		.attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) |
 			 PTE_BLOCK_INNER_SHARE
 	}, {
 		.virt = 0xc0000000UL,
 		.phys = 0xc0000000UL,
 		.size = 0x30000000UL,
 		.attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
 			 PTE_BLOCK_NON_SHARE |
 			 PTE_BLOCK_PXN | PTE_BLOCK_UXN
 	}, {
 		/* List terminator */
 		0,
 	}
 };

 struct mm_region *mem_map = gx_mem_map;

 /* Configure the Ethernet MAC with the requested interface mode
  * with some optional flags.
  */
 void meson_eth_init(phy_interface_t mode, unsigned int flags)
 {
 	switch (mode) {
 	case PHY_INTERFACE_MODE_RGMII:
 	case PHY_INTERFACE_MODE_RGMII_ID:
 	case PHY_INTERFACE_MODE_RGMII_RXID:
 	case PHY_INTERFACE_MODE_RGMII_TXID:
 		/* Set RGMII mode */
 		setbits_le32(GX_ETH_REG_0, GX_ETH_REG_0_PHY_INTF |
 			     GX_ETH_REG_0_TX_PHASE(1) |
 			     GX_ETH_REG_0_TX_RATIO(4) |
 			     GX_ETH_REG_0_PHY_CLK_EN |
 			     GX_ETH_REG_0_CLK_EN);

 		break;

 	case PHY_INTERFACE_MODE_RMII:
 		/* Set RMII mode */
 		out_le32(GX_ETH_REG_0, GX_ETH_REG_0_INVERT_RMII_CLK |
 					 GX_ETH_REG_0_CLK_EN);

 		if (!IS_ENABLED(CONFIG_MESON_GXBB))
 			writel(0x10110181, GX_ETH_REG_2);

 		break;

 	default:
 		printf("Invalid Ethernet interface mode\n");
 		return;
 	}
 }

 #if CONFIG_IS_ENABLED(USB_DWC3_MESON_GXL) && \
 	CONFIG_IS_ENABLED(USB_GADGET_DWC2_OTG)
 static struct dwc2_plat_otg_data meson_gx_dwc2_data;

 int board_usb_init(int index, enum usb_init_type init)
 {
 	struct fdtdec_phandle_args args;
 	const void *blob = gd->fdt_blob;
 	int node, dwc2_node;
 	struct udevice *dev, *clk_dev;
 	struct clk clk;
 	int ret;

 	/* find the usb glue node */
 	node = fdt_node_offset_by_compatible(blob, -1,
 					     "amlogic,meson-gxl-usb-ctrl");
 	if (node < 0) {
 		node = fdt_node_offset_by_compatible(blob, -1,
 					"amlogic,meson-gxm-usb-ctrl");
 		if (node < 0) {
 			debug("Not found usb-control node\n");
 			return -ENODEV;
 		}
 	}

 	if (!fdtdec_get_is_enabled(blob, node)) {
 		debug("usb is disabled in the device tree\n");
 		return -ENODEV;
 	}

 	ret = uclass_get_device_by_of_offset(UCLASS_SIMPLE_BUS, node, &dev);
 	if (ret) {
 		debug("Not found usb-control device\n");
 		return ret;
 	}

 	/* find the dwc2 node */
 	dwc2_node = fdt_node_offset_by_compatible(blob, node,
 						  "amlogic,meson-g12a-usb");
 	if (dwc2_node < 0) {
 		debug("Not found dwc2 node\n");
 		return -ENODEV;
 	}

 	if (!fdtdec_get_is_enabled(blob, dwc2_node)) {
 		debug("dwc2 is disabled in the device tree\n");
 		return -ENODEV;
 	}

 	meson_gx_dwc2_data.regs_otg = fdtdec_get_addr(blob, dwc2_node, "reg");
 	if (meson_gx_dwc2_data.regs_otg == FDT_ADDR_T_NONE) {
 		debug("usbotg: can't get base address\n");
 		return -ENODATA;
 	}

 	/* Enable clock */
 	ret = fdtdec_parse_phandle_with_args(blob, dwc2_node, "clocks",
 					     "#clock-cells", 0, 0, &args);
 	if (ret) {
 		debug("usbotg has no clocks defined in the device tree\n");
 		return ret;
 	}

 	ret = uclass_get_device_by_of_offset(UCLASS_CLK, args.node, &clk_dev);
 	if (ret)
 		return ret;

 	if (args.args_count != 1) {
 		debug("Can't find clock ID in the device tree\n");
 		return -ENODATA;
 	}

 	clk.dev = clk_dev;
 	clk.id = args.args[0];

 	ret = clk_enable(&clk);
 	if (ret) {
 		debug("Failed to enable usbotg clock\n");
 		return ret;
 	}

 	meson_gx_dwc2_data.rx_fifo_sz = fdtdec_get_int(blob, dwc2_node,
 						     "g-rx-fifo-size", 0);
 	meson_gx_dwc2_data.np_tx_fifo_sz = fdtdec_get_int(blob, dwc2_node,
 							"g-np-tx-fifo-size", 0);
 	meson_gx_dwc2_data.tx_fifo_sz = fdtdec_get_int(blob, dwc2_node,
 						     "g-tx-fifo-size", 0);

 	/* Switch to peripheral mode */
 	ret = dwc3_meson_gxl_force_mode(dev, USB_DR_MODE_PERIPHERAL);
 	if (ret)
 		return ret;

 	return dwc2_udc_probe(&meson_gx_dwc2_data);
 }

 int board_usb_cleanup(int index, enum usb_init_type init)
 {
 	const void *blob = gd->fdt_blob;
 	struct udevice *dev;
 	int node;
 	int ret;

 	/* find the usb glue node */
 	node = fdt_node_offset_by_compatible(blob, -1,
 					     "amlogic,meson-gxl-usb-ctrl");
 	if (node < 0) {
 		node = fdt_node_offset_by_compatible(blob, -1,
 					"amlogic,meson-gxm-usb-ctrl");
 		if (node < 0) {
 			debug("Not found usb-control node\n");
 			return -ENODEV;
 		}
 	}

 	if (!fdtdec_get_is_enabled(blob, node))
 		return -ENODEV;

 	ret = uclass_get_device_by_of_offset(UCLASS_SIMPLE_BUS, node, &dev);
 	if (ret)
 		return ret;

 	/* Switch to OTG mode */
 	ret = dwc3_meson_gxl_force_mode(dev, USB_DR_MODE_HOST);
 	if (ret)
 		return ret;

 	return 0;
 }
 #endif
	// SPDX-License-Identifier: GPL-2.0+
	/*
	* (C) Copyright 2016 Beniamino Galvani <b.galvani@gmail.com>
	* (C) Copyright 2018 Neil Armstrong <narmstrong@baylibre.com>
	*/

	#include <common.h>
	#include <init.h>
	#include <net.h>
	#include <asm/arch/boot.h>
	#include <asm/arch/eth.h>
	#include <asm/arch/gx.h>
	#include <asm/arch/mem.h>
	#include <asm/arch/meson-vpu.h>
	#include <asm/global_data.h>
	#include <asm/io.h>
	#include <asm/armv8/mmu.h>
	#include <linux/sizes.h>
	#include <usb.h>
	#include <linux/usb/otg.h>
	#include <asm/arch/usb-gx.h>
	#include <usb/dwc2_udc.h>
	#include <clk.h>
	#include <phy.h>

	DECLARE_GLOBAL_DATA_PTR;

	int meson_get_boot_device(void)
	{
	return readl(GX_AO_SEC_GP_CFG0) & GX_AO_BOOT_DEVICE;
	}

	/* Configure the reserved memory zones exported by the secure registers
	* into EFI and DTB reserved memory entries.
	*/
	void meson_init_reserved_memory(void *fdt)
	{
	u64 bl31_size, bl31_start;
	u64 bl32_size, bl32_start;
	u32 reg;

	/*
	* Get ARM Trusted Firmware reserved memory zones in :
	* - AO_SEC_GP_CFG3: bl32 & bl31 size in KiB, can be 0
	* - AO_SEC_GP_CFG5: bl31 physical start address, can be NULL
	* - AO_SEC_GP_CFG4: bl32 physical start address, can be NULL
	*/
	reg = readl(GX_AO_SEC_GP_CFG3);

	bl31_size = ((reg & GX_AO_BL31_RSVMEM_SIZE_MASK)
	>> GX_AO_BL31_RSVMEM_SIZE_SHIFT) * SZ_1K;
	bl32_size = (reg & GX_AO_BL32_RSVMEM_SIZE_MASK) * SZ_1K;

	bl31_start = readl(GX_AO_SEC_GP_CFG5);
	bl32_start = readl(GX_AO_SEC_GP_CFG4);

	/*
	* Early Meson GX Firmware revisions did not provide the reserved
	* memory zones in the registers, keep fixed memory zone handling.
	*/
	if (IS_ENABLED(CONFIG_MESON_GX) &&
	!reg && !bl31_start && !bl32_start) {
	bl31_start = 0x10000000;
	bl31_size = 0x200000;
	}

	/* Add first 16MiB reserved zone */
	meson_board_add_reserved_memory(fdt, 0, GX_FIRMWARE_MEM_SIZE);

	/* Add BL31 reserved zone */
	if (bl31_start && bl31_size)
	meson_board_add_reserved_memory(fdt, bl31_start, bl31_size);

	/* Add BL32 reserved zone */
	if (bl32_start && bl32_size)
	meson_board_add_reserved_memory(fdt, bl32_start, bl32_size);

	#if defined(CONFIG_VIDEO_MESON)
	meson_vpu_rsv_fb(fdt);
	#endif
	}

	phys_size_t get_effective_memsize(void)
	{
	/* Size is reported in MiB, convert it in bytes */
	return ((readl(GX_AO_SEC_GP_CFG0) & GX_AO_MEM_SIZE_MASK)
	>> GX_AO_MEM_SIZE_SHIFT) * SZ_1M;
	}

	static struct mm_region gx_mem_map[] = {
	{
	.virt = 0x0UL,
	.phys = 0x0UL,
	.size = 0xc0000000UL,
	.attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) \|
	PTE_BLOCK_INNER_SHARE
	}, {
	.virt = 0xc0000000UL,
	.phys = 0xc0000000UL,
	.size = 0x30000000UL,
	.attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) \|
	PTE_BLOCK_NON_SHARE \|
	PTE_BLOCK_PXN \| PTE_BLOCK_UXN
	}, {
	/* List terminator */
	0,
	}
	};

	struct mm_region *mem_map = gx_mem_map;

	/* Configure the Ethernet MAC with the requested interface mode
	* with some optional flags.
	*/
	void meson_eth_init(phy_interface_t mode, unsigned int flags)
	{
	switch (mode) {
	case PHY_INTERFACE_MODE_RGMII:
	case PHY_INTERFACE_MODE_RGMII_ID:
	case PHY_INTERFACE_MODE_RGMII_RXID:
	case PHY_INTERFACE_MODE_RGMII_TXID:
	/* Set RGMII mode */
	setbits_le32(GX_ETH_REG_0, GX_ETH_REG_0_PHY_INTF \|
	GX_ETH_REG_0_TX_PHASE(1) \|
	GX_ETH_REG_0_TX_RATIO(4) \|
	GX_ETH_REG_0_PHY_CLK_EN \|
	GX_ETH_REG_0_CLK_EN);

	break;

	case PHY_INTERFACE_MODE_RMII:
	/* Set RMII mode */
	out_le32(GX_ETH_REG_0, GX_ETH_REG_0_INVERT_RMII_CLK \|
	GX_ETH_REG_0_CLK_EN);

	if (!IS_ENABLED(CONFIG_MESON_GXBB))
	writel(0x10110181, GX_ETH_REG_2);

	break;

	default:
	printf("Invalid Ethernet interface mode\n");
	return;
	}
	}

	#if CONFIG_IS_ENABLED(USB_DWC3_MESON_GXL) && \
	CONFIG_IS_ENABLED(USB_GADGET_DWC2_OTG)
	static struct dwc2_plat_otg_data meson_gx_dwc2_data;

	int board_usb_init(int index, enum usb_init_type init)
	{
	struct fdtdec_phandle_args args;
	const void *blob = gd->fdt_blob;
	int node, dwc2_node;
	struct udevice dev, clk_dev;
	struct clk clk;
	int ret;

	/* find the usb glue node */
	node = fdt_node_offset_by_compatible(blob, -1,
	"amlogic,meson-gxl-usb-ctrl");
	if (node < 0) {
	node = fdt_node_offset_by_compatible(blob, -1,
	"amlogic,meson-gxm-usb-ctrl");
	if (node < 0) {
	debug("Not found usb-control node\n");
	return -ENODEV;
	}
	}

	if (!fdtdec_get_is_enabled(blob, node)) {
	debug("usb is disabled in the device tree\n");
	return -ENODEV;
	}

	ret = uclass_get_device_by_of_offset(UCLASS_SIMPLE_BUS, node, &dev);
	if (ret) {
	debug("Not found usb-control device\n");
	return ret;
	}

	/* find the dwc2 node */
	dwc2_node = fdt_node_offset_by_compatible(blob, node,
	"amlogic,meson-g12a-usb");
	if (dwc2_node < 0) {
	debug("Not found dwc2 node\n");
	return -ENODEV;
	}

	if (!fdtdec_get_is_enabled(blob, dwc2_node)) {
	debug("dwc2 is disabled in the device tree\n");
	return -ENODEV;
	}

	meson_gx_dwc2_data.regs_otg = fdtdec_get_addr(blob, dwc2_node, "reg");
	if (meson_gx_dwc2_data.regs_otg == FDT_ADDR_T_NONE) {
	debug("usbotg: can't get base address\n");
	return -ENODATA;
	}

	/* Enable clock */
	ret = fdtdec_parse_phandle_with_args(blob, dwc2_node, "clocks",
	"#clock-cells", 0, 0, &args);
	if (ret) {
	debug("usbotg has no clocks defined in the device tree\n");
	return ret;
	}

	ret = uclass_get_device_by_of_offset(UCLASS_CLK, args.node, &clk_dev);
	if (ret)
	return ret;

	if (args.args_count != 1) {
	debug("Can't find clock ID in the device tree\n");
	return -ENODATA;
	}

	clk.dev = clk_dev;
	clk.id = args.args[0];

	ret = clk_enable(&clk);
	if (ret) {
	debug("Failed to enable usbotg clock\n");
	return ret;
	}

	meson_gx_dwc2_data.rx_fifo_sz = fdtdec_get_int(blob, dwc2_node,
	"g-rx-fifo-size", 0);
	meson_gx_dwc2_data.np_tx_fifo_sz = fdtdec_get_int(blob, dwc2_node,
	"g-np-tx-fifo-size", 0);
	meson_gx_dwc2_data.tx_fifo_sz = fdtdec_get_int(blob, dwc2_node,
	"g-tx-fifo-size", 0);

	/* Switch to peripheral mode */
	ret = dwc3_meson_gxl_force_mode(dev, USB_DR_MODE_PERIPHERAL);
	if (ret)
	return ret;

	return dwc2_udc_probe(&meson_gx_dwc2_data);
	}

	int board_usb_cleanup(int index, enum usb_init_type init)
	{
	const void *blob = gd->fdt_blob;
	struct udevice *dev;
	int node;
	int ret;

	/* find the usb glue node */
	node = fdt_node_offset_by_compatible(blob, -1,
	"amlogic,meson-gxl-usb-ctrl");
	if (node < 0) {
	node = fdt_node_offset_by_compatible(blob, -1,
	"amlogic,meson-gxm-usb-ctrl");
	if (node < 0) {
	debug("Not found usb-control node\n");
	return -ENODEV;
	}
	}

	if (!fdtdec_get_is_enabled(blob, node))
	return -ENODEV;

	ret = uclass_get_device_by_of_offset(UCLASS_SIMPLE_BUS, node, &dev);
	if (ret)
	return ret;

	/* Switch to OTG mode */
	ret = dwc3_meson_gxl_force_mode(dev, USB_DR_MODE_HOST);
	if (ret)
	return ret;

	return 0;
	}
	#endif