| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright (C) 2012 Lucas Stach |
| */ |
| |
| #include <env.h> |
| #include <fdt_support.h> |
| #include <init.h> |
| #include <log.h> |
| #include <asm/arch/clock.h> |
| #include <asm/arch/funcmux.h> |
| #include <asm/arch/pinmux.h> |
| #include <asm/arch-tegra/ap.h> |
| #include <asm/arch-tegra/board.h> |
| #include <asm/arch-tegra/tegra.h> |
| #include <asm/global_data.h> |
| #include <asm/gpio.h> |
| #include <asm/io.h> |
| #include <i2c.h> |
| #include <nand.h> |
| #include <linux/delay.h> |
| #include "../common/tdx-common.h" |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| #define PMU_I2C_ADDRESS 0x34 |
| #define MAX_I2C_RETRY 3 |
| #define PMU_SUPPLYENE 0x14 |
| #define PMU_SUPPLYENE_SYSINEN (1<<5) |
| #define PMU_SUPPLYENE_EXITSLREQ (1<<1) |
| |
| int arch_misc_init(void) |
| { |
| /* Disable PMIC sleep mode on low supply voltage */ |
| struct udevice *dev; |
| u8 addr, data[1]; |
| int err; |
| |
| err = i2c_get_chip_for_busnum(0, PMU_I2C_ADDRESS, 1, &dev); |
| if (err) { |
| debug("%s: Cannot find PMIC I2C chip\n", __func__); |
| return err; |
| } |
| |
| addr = PMU_SUPPLYENE; |
| |
| err = dm_i2c_read(dev, addr, data, 1); |
| if (err) { |
| debug("failed to get PMU_SUPPLYENE\n"); |
| return err; |
| } |
| |
| data[0] &= ~PMU_SUPPLYENE_SYSINEN; |
| data[0] |= PMU_SUPPLYENE_EXITSLREQ; |
| |
| err = dm_i2c_write(dev, addr, data, 1); |
| if (err) { |
| debug("failed to set PMU_SUPPLYENE\n"); |
| return err; |
| } |
| |
| /* make sure SODIMM pin 87 nRESET_OUT is released properly */ |
| pinmux_set_func(PMUX_PINGRP_ATA, PMUX_FUNC_GMI); |
| |
| if (readl(NV_PA_BASE_SRAM + NVBOOTINFOTABLE_BOOTTYPE) == |
| NVBOOTTYPE_RECOVERY) |
| printf("USB recovery mode\n"); |
| |
| return 0; |
| } |
| |
| #if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) |
| int ft_board_setup(void *blob, struct bd_info *bd) |
| { |
| u8 enetaddr[6]; |
| |
| /* MAC addr */ |
| if (eth_env_get_enetaddr("ethaddr", enetaddr)) { |
| int err = fdt_find_and_setprop(blob, |
| "/usb@7d004000/ethernet@1", |
| "local-mac-address", enetaddr, 6, 0); |
| |
| /* Older device trees might have used a different node name */ |
| if (err < 0) |
| err = fdt_find_and_setprop(blob, |
| "/usb@7d004000/asix@1", |
| "local-mac-address", enetaddr, 6, 0); |
| |
| if (err >= 0) |
| puts(" MAC address updated...\n"); |
| } |
| |
| return ft_common_board_setup(blob, bd); |
| } |
| #endif |
| |
| #ifdef CONFIG_MMC_SDHCI_TEGRA |
| /* |
| * Routine: pin_mux_mmc |
| * Description: setup the pin muxes/tristate values for the SDMMC(s) |
| */ |
| void pin_mux_mmc(void) |
| { |
| funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATB_GMA_4_BIT); |
| pinmux_tristate_disable(PMUX_PINGRP_GMB); |
| } |
| #endif |
| |
| #ifdef CONFIG_TEGRA_NAND |
| void pin_mux_nand(void) |
| { |
| funcmux_select(PERIPH_ID_NDFLASH, FUNCMUX_NDFLASH_KBC_8_BIT); |
| |
| /* |
| * configure pingroup ATC to something unrelated to |
| * avoid ATC overriding KBC |
| */ |
| pinmux_set_func(PMUX_PINGRP_ATC, PMUX_FUNC_GMI); |
| } |
| #endif |
| |
| #ifdef CONFIG_USB_EHCI_TEGRA |
| void pin_mux_usb(void) |
| { |
| /* module internal USB bus to connect ethernet chipset */ |
| funcmux_select(PERIPH_ID_USB2, FUNCMUX_USB2_ULPI); |
| |
| /* ULPI reference clock output */ |
| pinmux_set_func(PMUX_PINGRP_CDEV2, PMUX_FUNC_PLLP_OUT4); |
| pinmux_tristate_disable(PMUX_PINGRP_CDEV2); |
| |
| /* PHY reset GPIO */ |
| pinmux_tristate_disable(PMUX_PINGRP_UAC); |
| |
| /* VBus GPIO */ |
| pinmux_tristate_disable(PMUX_PINGRP_DTE); |
| |
| /* Reset ASIX using LAN_RESET */ |
| gpio_request(TEGRA_GPIO(V, 4), "LAN_RESET"); |
| gpio_direction_output(TEGRA_GPIO(V, 4), 0); |
| pinmux_tristate_disable(PMUX_PINGRP_GPV); |
| udelay(5); |
| gpio_set_value(TEGRA_GPIO(V, 4), 1); |
| |
| /* USBH_PEN: USB 1 aka Tegra USB port 3 VBus */ |
| pinmux_tristate_disable(PMUX_PINGRP_SPIG); |
| } |
| #endif |
| |
| #ifdef CONFIG_VIDEO_TEGRA20 |
| /* |
| * Routine: pin_mux_display |
| * Description: setup the pin muxes/tristate values for the LCD interface) |
| */ |
| void pin_mux_display(void) |
| { |
| /* |
| * Manually untristate BL_ON (PT4 - SODIMM 71) as specified through |
| * device-tree |
| */ |
| pinmux_tristate_disable(PMUX_PINGRP_DTA); |
| |
| pinmux_set_func(PMUX_PINGRP_SDC, PMUX_FUNC_PWM); |
| pinmux_tristate_disable(PMUX_PINGRP_SDC); |
| } |
| |
| /* |
| * Backlight off before OS handover |
| */ |
| void board_preboot_os(void) |
| { |
| gpio_request(TEGRA_GPIO(T, 4), "BL_ON"); |
| gpio_direction_output(TEGRA_GPIO(T, 4), 0); |
| } |
| #endif |