doc/board/ti/am62x_beagleplay.rst - filogic/uboot - Gitiles

 .. SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
 .. sectionauthor:: Nishanth Menon <nm@ti.com>

 AM62x Beagleboard.org Beagleplay
 ================================

 Introduction:
 -------------

 BeagleBoard.org BeaglePlay is an easy to use, affordable open source
 hardware single board computer based on the Texas Instruments AM625
 SoC that allows you to create connected devices that work even at long
 distances using IEEE 802.15.4g LR-WPAN and IEEE 802.3cg 10Base-T1L.
 Expansion is provided over open standards based mikroBUS, Grove and
 QWIIC headers among other interfaces.

 Further information can be found at:

 * Product Page: https://beagleplay.org/
 * Hardware documentation: https://git.beagleboard.org/beagleplay/beagleplay

 Boot Flow:
 ----------
 Below is the pictorial representation of boot flow:

 .. image:: img/boot_diagram_k3_current.svg
   :alt: Boot flow diagram

 - On this platform, 'TI Foundational Security' (TIFS) functions as the
   security enclave master while 'Device Manager' (DM), also known as the
   'TISCI server' in "TI terminology", offers all the essential services.
   The A53 or M4F (Aux core) sends requests to TIFS/DM to accomplish these
   services, as illustrated in the diagram above.

 Sources:
 --------
 .. include::  k3.rst
     :start-after: .. k3_rst_include_start_boot_sources
     :end-before: .. k3_rst_include_end_boot_sources

 Build procedure:
 ----------------
 0. Setup the environment variables:

 .. include::  k3.rst
     :start-after: .. k3_rst_include_start_common_env_vars_desc
     :end-before: .. k3_rst_include_end_common_env_vars_desc

 .. include::  k3.rst
     :start-after: .. k3_rst_include_start_board_env_vars_desc
     :end-before: .. k3_rst_include_end_board_env_vars_desc

 Set the variables corresponding to this platform:

 .. include::  k3.rst
     :start-after: .. k3_rst_include_start_common_env_vars_defn
     :end-before: .. k3_rst_include_end_common_env_vars_defn
 .. prompt:: bash $

   export UBOOT_CFG_CORTEXR="am62x_evm_r5_defconfig beagleplay_r5.config"
   export UBOOT_CFG_CORTEXA="am62x_evm_a53_defconfig beagleplay_a53.config"
   export TFA_BOARD=lite
   # we dont use any extra TFA parameters
   unset TFA_EXTRA_ARGS
   export OPTEE_PLATFORM=k3-am62x
   export OPTEE_EXTRA_ARGS="CFG_WITH_SOFTWARE_PRNG=y"

 .. include::  am62x_sk.rst
     :start-after: .. am62x_evm_rst_include_start_build_steps
     :end-before: .. am62x_evm_rst_include_end_build_steps

 Target Images
 -------------
 Copy the below images to an SD card and boot:

 * tiboot3-am62x-gp-evm.bin from R5 build as tiboot3.bin
 * tispl.bin_unsigned from Cortex-A build as tispl.bin
 * u-boot.img_unsigned from Cortex-A build as u-boot.img

 Image formats
 -------------

 - tiboot3.bin

 .. image:: img/multi_cert_tiboot3.bin.svg
   :alt: tiboot3.bin image format

 - tispl.bin

 .. image:: img/dm_tispl.bin.svg
   :alt: tispl.bin image format

 Additional hardware for U-Boot development
 ------------------------------------------

 * Serial Console is critical for U-Boot development on BeaglePlay. See
   `BeaglePlay serial console documentation
   <https://docs.beagleboard.org/latest/boards/beagleplay/demos-and-tutorials/using-serial-console.html>`_.
 * uSD is preferred option over eMMC, and a SD/MMC reader will be needed.
 * (optionally) JTAG is useful when working with very early stages of boot.

 Default storage options
 -----------------------

 There are multiple storage media options on BeaglePlay, but primarily:

 * Onboard eMMC (default) - reliable, fast and meant for deployment use.
 * SD/MMC card interface (hold 'USR' switch and power on) - Entirely
   depends on the SD card quality.

 Flash to uSD card or how to deal with "bricked" Board
 -----------------------------------------------------

 When deploying or working on Linux, it's common to use the onboard
 eMMC. However, avoiding the eMMC and using the uSD card is safer when
 working with U-Boot.

 If you choose to  hand format your own bootable uSD card, be
 aware that it can be difficult. The following information
 may be helpful, but remember that it is only sometimes
 reliable, and partition options can cause issues. These
 can potentially help:

 * https://git.ti.com/cgit/arago-project/tisdk-setup-scripts/tree/create-sdcard.sh
 * https://elinux.org/Beagleboard:Expanding_File_System_Partition_On_A_microSD

 The simplest option is to start with a standard distribution
 image like those in `BeagleBoard.org Distros Page
 <https://www.beagleboard.org/distros>`_ and download a disk image for
 BeaglePlay. Pick a 16GB+ uSD card to be on the safer side.

 With an SD/MMC Card reader and `Balena Etcher
 <https://etcher.balena.io/>`_, having a functional setup in minutes is
 a trivial matter, and it works on almost all Host Operating Systems.
 Yes Windows users, Windows Subsystem for Linux(WSL) based development
 with U-Boot and update uSD card is practical.

 Updating U-Boot is a matter of copying the tiboot3.bin, tispl.bin and
 u-boot.img to the "BOOT" partition of the uSD card. Remember to sync
 and unmount (or Eject - depending on the Operating System) the uSD
 card prior to physically removing from SD card reader.

 Also see following section on switch setting used for booting using
 uSD card.

 .. note::
   Great news! If the board has not been damaged physically, there's no
   need to worry about it being "bricked" on this platform. You only have
   to flash an uSD card, plug it in, and reinstall the image on eMMC. This
   means that even if you make a mistake, you can quickly fix it and rest
   easy.

   If you are frequently working with uSD cards, you might find the
   following useful:

   * `USB-SD-Mux <https://www.linux-automation.com/en/products/usb-sd-mux.html>`_
   * `SD-Wire <https://wiki.tizen.org/SDWire>`_

 Flash to eMMC
 -------------

 The eMMC layout selected is user-friendly for developers. The
 boot hardware partition of the eMMC only contains the fixed-size
 tiboot3.bin image. This is because the contents of the boot partitions
 need to run from the SoC's internal SRAM, which remains a fixed size
 constant. The other components of the boot sequence, such as tispl.bin
 and u-boot.img, are located in the /BOOT partition in the User Defined
 Area (UDA) hardware partition of the eMMC. These components can vary
 significantly in size. The choice of keeping tiboot3.bin in boot0 or
 boot1 partition depends on A/B update requirements.

 .. image:: img/beagleplay_emmc.svg
   :alt: eMMC partitions and boot file organization for BeaglePlay

 The following are the steps from Linux shell to program eMMC:

 .. prompt:: bash #

   # Enable Boot0 boot
   mmc bootpart enable 1 2 /dev/mmcblk0
   mmc bootbus set single_backward x1 x8 /dev/mmcblk0
   mmc hwreset enable /dev/mmcblk0

   # Clear eMMC boot0
   echo '0' >> /sys/class/block/mmcblk0boot0/force_ro
   dd if=/dev/zero of=/dev/mmcblk0boot0 count=32 bs=128k
   # Write tiboot3.bin
   dd if=tiboot3.bin of=/dev/mmcblk0boot0 bs=128k

   # Copy the rest of the boot binaries
   mount /dev/mmcblk0p1 /boot/firmware
   cp tispl.bin /boot/firmware
   cp u-boot.img /boot/firmware
   sync

 .. warning ::

   U-Boot is configured to prioritize booting from an SD card if it
   detects a valid boot partition and boot files on it, even if the
   system initially booted from eMMC. The boot order is set as follows:

   * SD/MMC
   * eMMC
   * USB
   * PXE

 LED patterns during boot
 ------------------------

 .. list-table:: USR LED status indication
    :widths: 16 16
    :header-rows: 1

    * - USR LEDs (012345)
      - Indicates

    * - 00000
      - Boot failure or R5 image not started up

    * - 11111
      - A53 SPL/U-boot has started up

    * - 10101
      - OS boot process has been initiated

    * - 01010
      - OS boot process failed and drops to U-Boot shell

 .. note ::

   In the table above, 0 indicates LED switched off and 1 indicates LED
   switched ON.

 .. warning ::

   If the "red" power LED is not glowing, the system power supply is not
   functional. Please refer to `BeaglePlay documentation
   <https://beagleplay.org/>`_ for further information.

 A53 SPL DDR Memory Layout
 -------------------------

 .. include::  am62x_sk.rst
     :start-after: .. am62x_evm_rst_include_start_ddr_mem_layout
     :end-before: .. am62x_evm_rst_include_end_ddr_mem_layout

 Switch Setting for Boot Mode
 ----------------------------

 The boot time option is configured via "USR" button on the board.
 See `Beagleplay Schematics <https://git.beagleboard.org/beagleplay/beagleplay/-/blob/main/BeaglePlay_sch.pdf>`_
 for details.

 .. list-table:: Boot Modes
    :widths: 16 16 16
    :header-rows: 1

    * - USR Switch Position
      - Primary Boot
      - Secondary Boot

    * - Not Pressed
      - eMMC
      - UART

    * - Pressed
      - SD/MMC File System (FS) mode
      - USB Device Firmware Upgrade (DFU) mode

 To switch to SD card boot mode, hold the USR button while powering on
 with Type-C power supply, then release when power LED lights up.

 Debugging U-Boot
 ----------------

 See :ref:`Common Debugging environment - OpenOCD<k3_rst_refer_openocd>`: for
 detailed setup and debugging information.

 .. warning::

   **OpenOCD support since**: v0.12.0

   If the default package version of OpenOCD in your development
   environment's distribution needs to be updated, it might be necessary to
   build OpenOCD from the source.

 .. include::  k3.rst
     :start-after: .. k3_rst_include_start_openocd_connect_tag_connect
     :end-before: .. k3_rst_include_end_openocd_connect_tag_connect

 .. include::  k3.rst
     :start-after: .. k3_rst_include_start_openocd_cfg_external_intro
     :end-before: .. k3_rst_include_end_openocd_cfg_external_intro

 For example, with BeaglePlay (AM62X platform), the openocd_connect.cfg:

 .. code-block:: tcl

   # TUMPA example:
   # http://www.tiaowiki.com/w/TIAO_USB_Multi_Protocol_Adapter_User's_Manual
   source [find interface/ftdi/tumpa.cfg]

   transport select jtag

   # default JTAG configuration has only SRST and no TRST
   reset_config srst_only srst_push_pull

   # delay after SRST goes inactive
   adapter srst delay 20

   if { ![info exists SOC] } {
     # Set the SoC of interest
     set SOC am625
   }

   source [find target/ti_k3.cfg]

   ftdi tdo_sample_edge falling

   # Speeds for FT2232H are in multiples of 2, and 32MHz is tops
   # max speed we seem to achieve is ~20MHz.. so we pick 16MHz
   adapter speed 16000
	.. SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
	.. sectionauthor:: Nishanth Menon <nm@ti.com>

	AM62x Beagleboard.org Beagleplay
	================================

	Introduction:
	-------------

	BeagleBoard.org BeaglePlay is an easy to use, affordable open source
	hardware single board computer based on the Texas Instruments AM625
	SoC that allows you to create connected devices that work even at long
	distances using IEEE 802.15.4g LR-WPAN and IEEE 802.3cg 10Base-T1L.
	Expansion is provided over open standards based mikroBUS, Grove and
	QWIIC headers among other interfaces.

	Further information can be found at:

	* Product Page: https://beagleplay.org/
	* Hardware documentation: https://git.beagleboard.org/beagleplay/beagleplay

	Boot Flow:
	----------
	Below is the pictorial representation of boot flow:

	.. image:: img/boot_diagram_k3_current.svg
	:alt: Boot flow diagram

	- On this platform, 'TI Foundational Security' (TIFS) functions as the
	security enclave master while 'Device Manager' (DM), also known as the
	'TISCI server' in "TI terminology", offers all the essential services.
	The A53 or M4F (Aux core) sends requests to TIFS/DM to accomplish these
	services, as illustrated in the diagram above.

	Sources:
	--------
	.. include:: k3.rst
	:start-after: .. k3_rst_include_start_boot_sources
	:end-before: .. k3_rst_include_end_boot_sources

	Build procedure:
	----------------
	0. Setup the environment variables:

	.. include:: k3.rst
	:start-after: .. k3_rst_include_start_common_env_vars_desc
	:end-before: .. k3_rst_include_end_common_env_vars_desc

	.. include:: k3.rst
	:start-after: .. k3_rst_include_start_board_env_vars_desc
	:end-before: .. k3_rst_include_end_board_env_vars_desc

	Set the variables corresponding to this platform:

	.. include:: k3.rst
	:start-after: .. k3_rst_include_start_common_env_vars_defn
	:end-before: .. k3_rst_include_end_common_env_vars_defn
	.. prompt:: bash $

	export UBOOT_CFG_CORTEXR="am62x_evm_r5_defconfig beagleplay_r5.config"
	export UBOOT_CFG_CORTEXA="am62x_evm_a53_defconfig beagleplay_a53.config"
	export TFA_BOARD=lite
	# we dont use any extra TFA parameters
	unset TFA_EXTRA_ARGS
	export OPTEE_PLATFORM=k3-am62x
	export OPTEE_EXTRA_ARGS="CFG_WITH_SOFTWARE_PRNG=y"

	.. include:: am62x_sk.rst
	:start-after: .. am62x_evm_rst_include_start_build_steps
	:end-before: .. am62x_evm_rst_include_end_build_steps

	Target Images
	-------------
	Copy the below images to an SD card and boot:

	* tiboot3-am62x-gp-evm.bin from R5 build as tiboot3.bin
	* tispl.bin_unsigned from Cortex-A build as tispl.bin
	* u-boot.img_unsigned from Cortex-A build as u-boot.img

	Image formats
	-------------

	- tiboot3.bin

	.. image:: img/multi_cert_tiboot3.bin.svg
	:alt: tiboot3.bin image format

	- tispl.bin

	.. image:: img/dm_tispl.bin.svg
	:alt: tispl.bin image format

	Additional hardware for U-Boot development
	------------------------------------------

	* Serial Console is critical for U-Boot development on BeaglePlay. See
	`BeaglePlay serial console documentation
	<https://docs.beagleboard.org/latest/boards/beagleplay/demos-and-tutorials/using-serial-console.html>`_.
	* uSD is preferred option over eMMC, and a SD/MMC reader will be needed.
	* (optionally) JTAG is useful when working with very early stages of boot.

	Default storage options
	-----------------------

	There are multiple storage media options on BeaglePlay, but primarily:

	* Onboard eMMC (default) - reliable, fast and meant for deployment use.
	* SD/MMC card interface (hold 'USR' switch and power on) - Entirely
	depends on the SD card quality.

	Flash to uSD card or how to deal with "bricked" Board
	-----------------------------------------------------

	When deploying or working on Linux, it's common to use the onboard
	eMMC. However, avoiding the eMMC and using the uSD card is safer when
	working with U-Boot.

	If you choose to hand format your own bootable uSD card, be
	aware that it can be difficult. The following information
	may be helpful, but remember that it is only sometimes
	reliable, and partition options can cause issues. These
	can potentially help:

	* https://git.ti.com/cgit/arago-project/tisdk-setup-scripts/tree/create-sdcard.sh
	* https://elinux.org/Beagleboard:Expanding_File_System_Partition_On_A_microSD

	The simplest option is to start with a standard distribution
	image like those in `BeagleBoard.org Distros Page
	<https://www.beagleboard.org/distros>`_ and download a disk image for
	BeaglePlay. Pick a 16GB+ uSD card to be on the safer side.

	With an SD/MMC Card reader and `Balena Etcher
	<https://etcher.balena.io/>`_, having a functional setup in minutes is
	a trivial matter, and it works on almost all Host Operating Systems.
	Yes Windows users, Windows Subsystem for Linux(WSL) based development
	with U-Boot and update uSD card is practical.

	Updating U-Boot is a matter of copying the tiboot3.bin, tispl.bin and
	u-boot.img to the "BOOT" partition of the uSD card. Remember to sync
	and unmount (or Eject - depending on the Operating System) the uSD
	card prior to physically removing from SD card reader.

	Also see following section on switch setting used for booting using
	uSD card.

	.. note::
	Great news! If the board has not been damaged physically, there's no
	need to worry about it being "bricked" on this platform. You only have
	to flash an uSD card, plug it in, and reinstall the image on eMMC. This
	means that even if you make a mistake, you can quickly fix it and rest
	easy.

	If you are frequently working with uSD cards, you might find the
	following useful:

	* `USB-SD-Mux <https://www.linux-automation.com/en/products/usb-sd-mux.html>`_
	* `SD-Wire <https://wiki.tizen.org/SDWire>`_

	Flash to eMMC
	-------------

	The eMMC layout selected is user-friendly for developers. The
	boot hardware partition of the eMMC only contains the fixed-size
	tiboot3.bin image. This is because the contents of the boot partitions
	need to run from the SoC's internal SRAM, which remains a fixed size
	constant. The other components of the boot sequence, such as tispl.bin
	and u-boot.img, are located in the /BOOT partition in the User Defined
	Area (UDA) hardware partition of the eMMC. These components can vary
	significantly in size. The choice of keeping tiboot3.bin in boot0 or
	boot1 partition depends on A/B update requirements.

	.. image:: img/beagleplay_emmc.svg
	:alt: eMMC partitions and boot file organization for BeaglePlay

	The following are the steps from Linux shell to program eMMC:

	.. prompt:: bash #

	# Enable Boot0 boot
	mmc bootpart enable 1 2 /dev/mmcblk0
	mmc bootbus set single_backward x1 x8 /dev/mmcblk0
	mmc hwreset enable /dev/mmcblk0

	# Clear eMMC boot0
	echo '0' >> /sys/class/block/mmcblk0boot0/force_ro
	dd if=/dev/zero of=/dev/mmcblk0boot0 count=32 bs=128k
	# Write tiboot3.bin
	dd if=tiboot3.bin of=/dev/mmcblk0boot0 bs=128k

	# Copy the rest of the boot binaries
	mount /dev/mmcblk0p1 /boot/firmware
	cp tispl.bin /boot/firmware
	cp u-boot.img /boot/firmware
	sync

	.. warning ::

	U-Boot is configured to prioritize booting from an SD card if it
	detects a valid boot partition and boot files on it, even if the
	system initially booted from eMMC. The boot order is set as follows:

	* SD/MMC
	* eMMC
	* USB
	* PXE

	LED patterns during boot
	------------------------

	.. list-table:: USR LED status indication
	:widths: 16 16
	:header-rows: 1

	* - USR LEDs (012345)
	- Indicates

	* - 00000
	- Boot failure or R5 image not started up

	* - 11111
	- A53 SPL/U-boot has started up

	* - 10101
	- OS boot process has been initiated

	* - 01010
	- OS boot process failed and drops to U-Boot shell

	.. note ::

	In the table above, 0 indicates LED switched off and 1 indicates LED
	switched ON.

	.. warning ::

	If the "red" power LED is not glowing, the system power supply is not
	functional. Please refer to `BeaglePlay documentation
	<https://beagleplay.org/>`_ for further information.

	A53 SPL DDR Memory Layout
	-------------------------

	.. include:: am62x_sk.rst
	:start-after: .. am62x_evm_rst_include_start_ddr_mem_layout
	:end-before: .. am62x_evm_rst_include_end_ddr_mem_layout

	Switch Setting for Boot Mode
	----------------------------

	The boot time option is configured via "USR" button on the board.
	See `Beagleplay Schematics <https://git.beagleboard.org/beagleplay/beagleplay/-/blob/main/BeaglePlay_sch.pdf>`_
	for details.

	.. list-table:: Boot Modes
	:widths: 16 16 16
	:header-rows: 1

	* - USR Switch Position
	- Primary Boot
	- Secondary Boot

	* - Not Pressed
	- eMMC
	- UART

	* - Pressed
	- SD/MMC File System (FS) mode
	- USB Device Firmware Upgrade (DFU) mode

	To switch to SD card boot mode, hold the USR button while powering on
	with Type-C power supply, then release when power LED lights up.

	Debugging U-Boot
	----------------

	See :ref:`Common Debugging environment - OpenOCD<k3_rst_refer_openocd>`: for
	detailed setup and debugging information.

	.. warning::

	OpenOCD support since: v0.12.0

	If the default package version of OpenOCD in your development
	environment's distribution needs to be updated, it might be necessary to
	build OpenOCD from the source.

	.. include:: k3.rst
	:start-after: .. k3_rst_include_start_openocd_connect_tag_connect
	:end-before: .. k3_rst_include_end_openocd_connect_tag_connect

	.. include:: k3.rst
	:start-after: .. k3_rst_include_start_openocd_cfg_external_intro
	:end-before: .. k3_rst_include_end_openocd_cfg_external_intro

	For example, with BeaglePlay (AM62X platform), the openocd_connect.cfg:

	.. code-block:: tcl

	# TUMPA example:
	# http://www.tiaowiki.com/w/TIAO_USB_Multi_Protocol_Adapter_User's_Manual
	source [find interface/ftdi/tumpa.cfg]

	transport select jtag

	# default JTAG configuration has only SRST and no TRST
	reset_config srst_only srst_push_pull

	# delay after SRST goes inactive
	adapter srst delay 20

	if { ![info exists SOC] } {
	# Set the SoC of interest
	set SOC am625
	}

	source [find target/ti_k3.cfg]

	ftdi tdo_sample_edge falling

	# Speeds for FT2232H are in multiples of 2, and 32MHz is tops
	# max speed we seem to achieve is ~20MHz.. so we pick 16MHz
	adapter speed 16000