blob: 56a16502dcc736cb4ab797edae175093b33ba8d2 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2010-2011 Freescale Semiconductor, Inc.
* Copyright 2020 NXP
*/
/*
* QorIQ RDB boards configuration file
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <linux/stringify.h>
#if defined(CONFIG_TARGET_P1020RDB_PC)
#define CONFIG_VSC7385_ENET
#define CONFIG_SLIC
#define __SW_BOOT_MASK 0x03
#define __SW_BOOT_NOR 0x5c
#define __SW_BOOT_SPI 0x1c
#define __SW_BOOT_SD 0x9c
#define __SW_BOOT_NAND 0xec
#define __SW_BOOT_PCIE 0x6c
#define __SW_NOR_BANK_MASK 0xfd
#define __SW_NOR_BANK_UP 0x00
#define __SW_NOR_BANK_LO 0x02
#define CONFIG_SYS_L2_SIZE (256 << 10)
#endif
/*
* P1020RDB-PD board has user selectable switches for evaluating different
* frequency and boot options for the P1020 device. The table that
* follow describe the available options. The front six binary number was in
* accordance with SW3[1:6].
* 111101 533 533 267 667 NOR Core0 boot; Core1 hold-off
* 101101 667 667 333 667 NOR Core0 boot; Core1 hold-off
* 011001 800 800 400 667 NOR Core0 boot; Core1 hold-off
* 001001 800 800 400 667 SD/MMC Core0 boot; Core1 hold-off
* 001101 800 800 400 667 SPI Core0 boot; Core1 hold-off
* 010001 800 800 400 667 NAND Core0 boot; Core1 hold-off
* 011101 800 800 400 667 PCIe-2 Core0 boot; Core1 hold-off
*/
#if defined(CONFIG_TARGET_P1020RDB_PD)
#define CONFIG_VSC7385_ENET
#define CONFIG_SLIC
#define __SW_BOOT_MASK 0x03
#define __SW_BOOT_NOR 0x64
#define __SW_BOOT_SPI 0x34
#define __SW_BOOT_SD 0x24
#define __SW_BOOT_NAND 0x44
#define __SW_BOOT_PCIE 0x74
#define __SW_NOR_BANK_MASK 0xfd
#define __SW_NOR_BANK_UP 0x00
#define __SW_NOR_BANK_LO 0x02
#define CONFIG_SYS_L2_SIZE (256 << 10)
/*
* Dynamic MTD Partition support with mtdparts
*/
#endif
#if defined(CONFIG_TARGET_P2020RDB)
#define CONFIG_VSC7385_ENET
#define __SW_BOOT_MASK 0x03
#define __SW_BOOT_NOR 0xc8
#define __SW_BOOT_SPI 0x28
#define __SW_BOOT_SD 0x68
#define __SW_BOOT_SD2 0x18
#define __SW_BOOT_NAND 0xe8
#define __SW_BOOT_PCIE 0xa8
#define __SW_NOR_BANK_MASK 0xfd
#define __SW_NOR_BANK_UP 0x00
#define __SW_NOR_BANK_LO 0x02
#define CONFIG_SYS_L2_SIZE (512 << 10)
/*
* Dynamic MTD Partition support with mtdparts
*/
#endif
#ifdef CONFIG_SDCARD
#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10)
#define CONFIG_SYS_MMC_U_BOOT_DST (0x11000000)
#define CONFIG_SYS_MMC_U_BOOT_START (0x11000000)
#define CONFIG_SYS_MMC_U_BOOT_OFFS (128 << 10)
#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#elif defined(CONFIG_SPIFLASH)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x11000000)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x11000000)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (128 << 10)
#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#elif defined(CONFIG_MTD_RAW_NAND)
#ifdef CONFIG_TPL_BUILD
#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#define CONFIG_SYS_NAND_U_BOOT_SIZE (832 << 10)
#define CONFIG_SYS_NAND_U_BOOT_DST (0x11000000)
#define CONFIG_SYS_NAND_U_BOOT_START (0x11000000)
#elif defined(CONFIG_SPL_BUILD)
#define CONFIG_SYS_NAND_U_BOOT_SIZE (128 << 10)
#define CONFIG_SYS_NAND_U_BOOT_DST 0xf8f80000
#define CONFIG_SYS_NAND_U_BOOT_START 0xf8f80000
#else
#ifndef CONFIG_MPC85XX_HAVE_RESET_VECTOR
#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#endif
#endif /* not CONFIG_TPL_BUILD */
#endif
#ifndef CONFIG_RESET_VECTOR_ADDRESS
#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
#endif
#define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */
#define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */
#define CONFIG_LBA48
#define CONFIG_HWCONFIG
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CONFIG_L2_CACHE
#define CONFIG_ENABLE_36BIT_PHYS
#define CONFIG_SYS_CCSRBAR 0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
#define CONFIG_SYS_DDR_RAW_TIMING
#define CONFIG_SYS_SPD_BUS_NUM 1
#define SPD_EEPROM_ADDRESS 0x52
#if defined(CONFIG_TARGET_P1020RDB_PD)
#define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_2G
#else
#define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_1G
#endif
#define CONFIG_SYS_SDRAM_SIZE (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19))
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
/* Default settings for DDR3 */
#ifndef CONFIG_TARGET_P2020RDB
#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f
#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302
#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000
#define CONFIG_SYS_DDR_CS1_BNDS 0x0040007f
#define CONFIG_SYS_DDR_CS1_CONFIG 0x80014302
#define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000
#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000
#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000
#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000
#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600
#define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8655A608
#define CONFIG_SYS_DDR_SR_CNTR 0x00000000
#define CONFIG_SYS_DDR_RCW_1 0x00000000
#define CONFIG_SYS_DDR_RCW_2 0x00000000
#define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */
#define CONFIG_SYS_DDR_CONTROL_2 0x04401050
#define CONFIG_SYS_DDR_TIMING_4 0x00220001
#define CONFIG_SYS_DDR_TIMING_5 0x03402400
#define CONFIG_SYS_DDR_TIMING_3 0x00020000
#define CONFIG_SYS_DDR_TIMING_0 0x00330004
#define CONFIG_SYS_DDR_TIMING_1 0x6f6B4846
#define CONFIG_SYS_DDR_TIMING_2 0x0FA8C8CF
#define CONFIG_SYS_DDR_CLK_CTRL 0x03000000
#define CONFIG_SYS_DDR_MODE_1 0x40461520
#define CONFIG_SYS_DDR_MODE_2 0x8000c000
#define CONFIG_SYS_DDR_INTERVAL 0x0C300000
#endif
/*
* Memory map
*
* 0x0000_0000 0x7fff_ffff DDR Up to 2GB cacheable
* 0x8000_0000 0xdfff_ffff PCI Express Mem 1.5G non-cacheable(PCIe * 3)
* 0xec00_0000 0xefff_ffff NOR flash Up to 64M non-cacheable CS0/1
* 0xf8f8_0000 0xf8ff_ffff L2 SRAM Up to 512K cacheable
* (early boot only)
* 0xff80_0000 0xff80_7fff NAND flash 32K non-cacheable CS1/0
* 0xff98_0000 0xff98_ffff PMC 64K non-cacheable CS2
* 0xffa0_0000 0xffaf_ffff CPLD 1M non-cacheable CS3
* 0xffb0_0000 0xffbf_ffff VSC7385 switch 1M non-cacheable CS2
* 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable
* 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable
* 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
*/
/*
* Local Bus Definitions
*/
#if defined(CONFIG_TARGET_P1020RDB_PD)
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */
#define CONFIG_SYS_FLASH_BASE 0xec000000
#else
#define CONFIG_SYS_MAX_FLASH_SECT 128 /* 16M */
#define CONFIG_SYS_FLASH_BASE 0xef000000
#endif
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
#else
#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
#endif
#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
| BR_PS_16 | BR_V)
#define CONFIG_FLASH_OR_PRELIM 0xfc000ff7
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CONFIG_SYS_FLASH_EMPTY_INFO
/* Nand Flash */
#ifdef CONFIG_NAND_FSL_ELBC
#define CONFIG_SYS_NAND_BASE 0xff800000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_NAND_BASE_PHYS 0xfff800000ull
#else
#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
#endif
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
| BR_PS_8 /* Port Size = 8 bit */ \
| BR_MS_FCM /* MSEL = FCM */ \
| BR_V) /* valid */
#if defined(CONFIG_TARGET_P1020RDB_PD)
#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_32KB \
| OR_FCM_PGS /* Large Page*/ \
| OR_FCM_CSCT \
| OR_FCM_CST \
| OR_FCM_CHT \
| OR_FCM_SCY_1 \
| OR_FCM_TRLX \
| OR_FCM_EHTR)
#else
#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_32KB /* small page */ \
| OR_FCM_CSCT \
| OR_FCM_CST \
| OR_FCM_CHT \
| OR_FCM_SCY_1 \
| OR_FCM_TRLX \
| OR_FCM_EHTR)
#endif
#endif /* CONFIG_NAND_FSL_ELBC */
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
/* The assembler doesn't like typecast */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
#else
/* Initial L1 address */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
#endif
/* Size of used area in RAM */
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
#define CONFIG_SYS_CPLD_BASE 0xffa00000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_CPLD_BASE_PHYS 0xfffa00000ull
#else
#define CONFIG_SYS_CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE
#endif
/* CPLD config size: 1Mb */
#define CONFIG_SYS_PMC_BASE 0xff980000
#define CONFIG_SYS_PMC_BASE_PHYS CONFIG_SYS_PMC_BASE
#define CONFIG_PMC_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \
BR_PS_8 | BR_V)
#define CONFIG_PMC_OR_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \
OR_GPCM_EAD)
/* Vsc7385 switch */
#ifdef CONFIG_VSC7385_ENET
#define __VSCFW_ADDR "vscfw_addr=ef000000\0"
#define CONFIG_SYS_VSC7385_BASE 0xffb00000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_VSC7385_BASE_PHYS 0xfffb00000ull
#else
#define CONFIG_SYS_VSC7385_BASE_PHYS CONFIG_SYS_VSC7385_BASE
#endif
#define CONFIG_SYS_VSC7385_BR_PRELIM \
(BR_PHYS_ADDR(CONFIG_SYS_VSC7385_BASE_PHYS) | BR_PS_8 | BR_V)
#define CONFIG_SYS_VSC7385_OR_PRELIM (OR_AM_128KB | OR_GPCM_CSNT | \
OR_GPCM_XACS | OR_GPCM_SCY_15 | OR_GPCM_SETA | \
OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
/* The size of the VSC7385 firmware image */
#define CONFIG_VSC7385_IMAGE_SIZE 8192
#endif
#ifndef __VSCFW_ADDR
#define __VSCFW_ADDR ""
#endif
/*
* Config the L2 Cache as L2 SRAM
*/
#if defined(CONFIG_SPL_BUILD)
#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH)
#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
#elif defined(CONFIG_MTD_RAW_NAND)
#ifdef CONFIG_TPL_BUILD
#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
#else
#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
#endif /* CONFIG_TPL_BUILD */
#endif
#endif
/* Serial Port - controlled on board with jumper J8
* open - index 2
* shorted - index 1
*/
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#if defined(CONFIG_SPL_BUILD) && CONFIG_IS_ENABLED(INIT_MINIMAL)
#define CONFIG_NS16550_MIN_FUNCTIONS
#endif
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
/* I2C */
#if !CONFIG_IS_ENABLED(DM_I2C)
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
#endif
#define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */
/*
* I2C2 EEPROM
*/
#define CONFIG_RTC_PT7C4338
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
#define CONFIG_SYS_I2C_PCA9557_ADDR 0x18
/* enable read and write access to EEPROM */
#if defined(CONFIG_PCI)
/*
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
/* controller 2, direct to uli, tgtid 2, Base address 9000 */
#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
#else
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
#endif
#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull
#else
#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
#endif
/* controller 1, Slot 2, tgtid 1, Base address a000 */
#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
#else
#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
#endif
#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc00000ull
#else
#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000
#endif
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#endif /* CONFIG_PCI */
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_TSEC1
#define CONFIG_TSEC1_NAME "eTSEC1"
#define CONFIG_TSEC2
#define CONFIG_TSEC2_NAME "eTSEC2"
#define CONFIG_TSEC3
#define CONFIG_TSEC3_NAME "eTSEC3"
#define TSEC1_PHY_ADDR 2
#define TSEC2_PHY_ADDR 0
#define TSEC3_PHY_ADDR 1
#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define TSEC3_PHYIDX 0
#endif /* CONFIG_TSEC_ENET */
/*
* Environment
*/
#if defined(CONFIG_SDCARD)
#define CONFIG_FSL_FIXED_MMC_LOCATION
#elif defined(CONFIG_MTD_RAW_NAND)
#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE)
#ifdef CONFIG_TPL_BUILD
#define SPL_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (160 << 10))
#endif
#elif defined(CONFIG_SYS_RAMBOOT)
#define SPL_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
#endif
#define CONFIG_LOADS_ECHO /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
/*
* USB
*/
#define CONFIG_HAS_FSL_DR_USB
#if defined(CONFIG_HAS_FSL_DR_USB)
#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
#endif
#if defined(CONFIG_TARGET_P1020RDB_PD)
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#endif
#ifdef CONFIG_MMC
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
#endif
/*
* Miscellaneous configurable options
*/
/*
* For booting Linux, the board info and command line data
* have to be in the first 64 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
/*
* Environment Configuration
*/
#define CONFIG_HOSTNAME "unknown"
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
#include "p1_p2_bootsrc.h"
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
"loadaddr=1000000\0" \
"bootfile=uImage\0" \
"tftpflash=tftpboot $loadaddr $uboot; " \
"protect off " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
"erase " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize; " \
"protect on " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize\0" \
"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0" \
"consoledev=ttyS0\0" \
"ramdiskaddr=2000000\0" \
"ramdiskfile=rootfs.ext2.gz.uboot\0" \
"fdtaddr=1e00000\0" \
"bdev=sda1\0" \
"jffs2nor=mtdblock3\0" \
"norbootaddr=ef080000\0" \
"norfdtaddr=ef040000\0" \
"jffs2nand=mtdblock9\0" \
"nandbootaddr=100000\0" \
"nandfdtaddr=80000\0" \
"ramdisk_size=120000\0" \
__VSCFW_ADDR \
MAP_NOR_LO_CMD(map_lowernorbank) \
MAP_NOR_UP_CMD(map_uppernorbank) \
RST_NOR_CMD(norboot) \
RST_SPI_CMD(spiboot) \
RST_SD_CMD(sdboot) \
RST_NAND_CMD(nandboot) \
RST_PCIE_CMD(pciboot) \
""
#define CONFIG_USB_FAT_BOOT \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs " \
"ramdisk_size=$ramdisk_size;" \
"usb start;" \
"fatload usb 0:2 $loadaddr $bootfile;" \
"fatload usb 0:2 $fdtaddr $fdtfile;" \
"fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr"
#define CONFIG_USB_EXT2_BOOT \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs " \
"ramdisk_size=$ramdisk_size;" \
"usb start;" \
"ext2load usb 0:4 $loadaddr $bootfile;" \
"ext2load usb 0:4 $fdtaddr $fdtfile;" \
"ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr"
#define CONFIG_NORBOOT \
"setenv bootargs root=/dev/$jffs2nor rw " \
"console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \
"bootm $norbootaddr - $norfdtaddr"
#endif /* __CONFIG_H */