| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * dts file for Xilinx ZynqMP VPK120 RevA System Controller |
| * |
| * (C) Copyright 2021 - 2022, Xilinx, Inc. |
| * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc. |
| * |
| * Michal Simek <michal.simek@amd.com> |
| */ |
| /dts-v1/; |
| |
| #include "zynqmp.dtsi" |
| #include "zynqmp-clk-ccf.dtsi" |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/pinctrl/pinctrl-zynqmp.h> |
| #include <dt-bindings/phy/phy.h> |
| |
| / { |
| model = "ZynqMP System Controller on VPK120 board RevA"; |
| compatible = "xlnx,zynqmp-vpk120-revA", |
| "xlnx,zynqmp-vpk120", "xlnx,zynqmp"; |
| |
| aliases { |
| ethernet0 = &gem0; |
| i2c0 = &i2c0; |
| i2c1 = &i2c1; |
| mmc0 = &sdhci0; |
| serial0 = &uart0; |
| serial1 = &dcc; |
| spi0 = &qspi; |
| usb0 = &usb0; |
| usb1 = &usb1; |
| nvmem0 = &eeprom; |
| }; |
| |
| chosen { |
| bootargs = "earlycon"; |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| memory@0 { |
| device_type = "memory"; |
| reg = <0x0 0x0 0x0 0x80000000>; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| autorepeat; |
| button-16 { |
| label = "sw16"; |
| gpios = <&gpio 10 GPIO_ACTIVE_HIGH>; |
| linux,code = <BTN_MISC>; |
| wakeup-source; |
| autorepeat; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| heartbeat-led { /* ds40 */ |
| label = "heartbeat"; |
| gpios = <&gpio 9 GPIO_ACTIVE_HIGH>; |
| linux,default-trigger = "heartbeat"; |
| }; |
| }; |
| |
| si5332_0: si5332-0 { /* ps_ref_clk */ |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <33333333>; |
| }; |
| |
| si5332_1: si5332-1 { /* clk0_sgmii */ |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <33333333>; /* FIXME */ |
| }; |
| |
| si5332_2: si5332-2 { /* clk1_usb */ |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <27000000>; |
| }; |
| }; |
| |
| &qspi { /* MIO 0-5 */ |
| status = "okay"; |
| flash@0 { |
| compatible = "m25p80", "jedec,spi-nor"; /* mt25qu512abb8e12 512Mib */ |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0>; |
| spi-tx-bus-width = <4>; |
| spi-rx-bus-width = <4>; |
| spi-max-frequency = <108000000>; |
| partition@0 { /* for testing purpose */ |
| label = "qspi"; |
| reg = <0 0x4000000>; |
| }; |
| }; |
| }; |
| |
| &sdhci0 { /* emmc MIO 13-23 - with some settings MTFC16GAPALBH 16GB */ |
| status = "okay"; |
| non-removable; |
| disable-wp; |
| bus-width = <8>; |
| xlnx,mio-bank = <0>; |
| }; |
| |
| &uart0 { /* uart0 MIO38-39 */ |
| status = "okay"; |
| bootph-all; |
| }; |
| |
| &gem0 { |
| status = "okay"; |
| phy-handle = <&phy0>; |
| phy-mode = "sgmii"; /* DTG generates this properly 1512 */ |
| /* phys = <&psgtr 0 PHY_TYPE_SGMII 0 0>; */ |
| mdio: mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| /* reset-gpios = <&gpio 142 GPIO_ACTIVE_LOW>; */ |
| phy0: ethernet-phy@0 { |
| reg = <0>; |
| }; |
| }; |
| }; |
| |
| &gpio { |
| status = "okay"; |
| gpio-line-names = "QSPI_CLK", "QSPI_DQ1", "QSPI_DQ2", "QSPI_DQ3", "QSPI_DQ0", /* 0 - 4 */ |
| "QSPI_CS_B", "", "", "SYSCTLR_GPIO", "SYSCTLR_LED", /* 5 - 9 */ |
| "SYSCTLR_PB", "PMC_ZU4_TRIGGER", "", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */ |
| "EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */ |
| "EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST_B", "", /* 20 - 24 */ |
| "", "", "", "", "", /* 25 - 29 */ |
| "", "", "", "", "LP_I2C0_PMC_SCL", /* 30 - 34 */ |
| "LP_I2C0_PMC_SDA", "LP_I2C1_SCL", "LP_I2C1_SDA", "UART0_RXD_IN", "UART0_TXD_OUT", /* 35 - 39 */ |
| "", "", "ETH_RESET_B", "", "", /* 40 - 44 */ |
| "", "", "", "", "", /* 45 - 49 */ |
| "", "", "USB0_CLK", "USB0_DIR", "USB0_DATA2", /* 50 - 54 */ |
| "USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3", /* 55 - 59 */ |
| "USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "", /* 60 - 64 */ |
| "", "", "", "", "", /* 65 - 69 */ |
| "", "", "", "", "", /* 70 - 74 */ |
| "", "ETH_MDC", "ETH_MDIO", /* 75 - 77, MIO end and EMIO start */ |
| "SYSCTLR_VERSAL_MODE0", "SYSCTLR_VERSAL_MODE1", /* 78 - 79 */ |
| "SYSCTLR_VERSAL_MODE2", "SYSCTLR_VERSAL_MODE3", "SYSCTLR_POR_B_LS", "", "", /* 80 - 84 */ |
| "SYSCTLR_JTAG_S0", "SYSCTLR_JTAG_S1", "SYSCTLR_IIC_MUX0_RESET_B", "SYSCTLR_IIC_MUX1_RESET_B", "", /* 85 - 89 */ |
| "SYSCTLR_GPIO0", "SYSCTLR_GPIO1", "SYSCTLR_GPIO2", "SYSCTLR_GPIO3", "SYSCTLR_GPIO4", /* 90 - 94 */ |
| "SYSCTLR_GPIO5", "", "", "", "", /* 95 - 99 */ |
| "", "", "", "", "", /* 100 - 104 */ |
| "", "", "", "", "", /* 105 - 109 */ |
| "", "", "", "", "", /* 110 - 114 */ |
| "", "", "", "", "", /* 115 - 119 */ |
| "", "", "", "", "", /* 120 - 124 */ |
| "", "", "", "", "", /* 125 - 129 */ |
| "", "", "", "", "", /* 130 - 134 */ |
| "", "", "", "", "", /* 135 - 139 */ |
| "", "", "", "", "", /* 140 - 144 */ |
| "", "", "", "", "", /* 145 - 149 */ |
| "", "", "", "", "", /* 150 - 154 */ |
| "", "", "", "", "", /* 155 - 159 */ |
| "", "", "", "", "", /* 160 - 164 */ |
| "", "", "", "", "", /* 165 - 169 */ |
| "", "", "", ""; /* 170 - 173 */ |
| }; |
| |
| &i2c0 { /* MIO 34-35 - can't stay here */ |
| status = "okay"; |
| clock-frequency = <400000>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_i2c0_default>; |
| pinctrl-1 = <&pinctrl_i2c0_gpio>; |
| scl-gpios = <&gpio 34 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| sda-gpios = <&gpio 35 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| |
| tca6416_u233: gpio@20 { /* u233 */ /* FIXME - address maybe wrong */ |
| compatible = "ti,tca6416"; |
| reg = <0x20>; |
| gpio-controller; /* interrupt not connected */ |
| #gpio-cells = <2>; |
| gpio-line-names = "MAX6643_OT_B", "MAX6643_FANFAIL_B", "QSFPDD1_MODSELL", "QSFPDD1_MODSELL", /* 0 - 3 */ |
| "PMBUS2_INA226_ALERT", "", "", "MAX6643_FULL_SPEED", /* 4 - 7 */ |
| "FMCP1_FMC_PRSNT_M2C_B", "", "FMCP1_FMCP_PRSNT_M2C_B", "", /* 10 - 13 */ |
| "VCCINT_VRHOT_B", "8A34001_EXP_RST_B", "PMBUS_ALERT", "PMBUS1_INA226_ALERT"; /* 14 - 17 */ |
| }; |
| |
| i2c-mux@74 { /* u33 */ |
| compatible = "nxp,pca9548"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x74>; |
| /* reset-gpios = <&gpio SYSCTLR_IIC_MUX0_RESET_B GPIO_ACTIVE_HIGH>; */ |
| pmbus_i2c: i2c@0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0>; |
| /* On connector J325 */ |
| ir38060_41: regulator@41 { /* IR38060 - u259 */ |
| compatible = "infineon,ir38060", "infineon,ir38064"; |
| reg = <0x41>; /* i2c addr 0x11 */ |
| }; |
| ir38164_43: regulator@43 { /* IR38164 - u13 */ |
| compatible = "infineon,ir38164"; |
| reg = <0x43>; /* i2c addr 0x13 */ |
| }; |
| ir35221_45: pmic@46 { /* IR35221 - u152 */ |
| compatible = "infineon,ir35221"; |
| reg = <0x46>; /* PMBUS - 0x16 */ |
| }; |
| irps5401_47: pmic5401@47 { /* IRPS5401 - u160 */ |
| compatible = "infineon,irps5401"; |
| reg = <0x47>; /* i2c addr 0x17 */ |
| }; |
| ir38164_49: regulator@49 { /* IR38164 - u189 */ |
| compatible = "infineon,ir38164"; |
| reg = <0x49>; /* i2c addr 0x19 */ |
| }; |
| irps5401_4c: pmic@4c { /* IRPS5401 - u167 */ |
| compatible = "infineon,irps5401"; |
| reg = <0x4c>; /* i2c addr 0x1c */ |
| }; |
| irps5401_4d: pmic@4d { /* IRPS5401 - u175 */ |
| compatible = "infineon,irps5401"; |
| reg = <0x4d>; /* i2c addr 0x1c */ |
| }; |
| ir38164_4e: regulator@4e { /* IR38164 - u184 */ |
| compatible = "infineon,ir38164"; |
| reg = <0x4e>; /* i2c addr 0x1e */ |
| }; |
| ir38164_4f: regulator@4f { /* IR38164 - u187 */ |
| compatible = "infineon,ir38164"; |
| reg = <0x4f>; /* i2c addr 0x1f */ |
| }; |
| }; |
| pmbus1_ina226_i2c: i2c@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <1>; |
| /* FIXME check alerts coming to SC */ |
| vccint: ina226@40 { /* u65 */ |
| compatible = "ti,ina226"; |
| reg = <0x40>; |
| shunt-resistor = <5000>; |
| }; |
| vcc_soc: ina226@41 { /* u161 */ |
| compatible = "ti,ina226"; |
| reg = <0x41>; |
| shunt-resistor = <5000>; |
| }; |
| vcc_pmc: ina226@42 { /* u163 */ |
| compatible = "ti,ina226"; |
| reg = <0x42>; |
| shunt-resistor = <5000>; |
| }; |
| vcc_ram: ina226@43 { /* u5 */ |
| compatible = "ti,ina226"; |
| reg = <0x43>; |
| shunt-resistor = <5000>; |
| }; |
| vcc_pslp: ina226@44 { /* u165 */ |
| compatible = "ti,ina226"; |
| reg = <0x44>; |
| shunt-resistor = <5000>; |
| }; |
| vcc_psfp: ina226@45 { /* u164 */ |
| compatible = "ti,ina226"; |
| reg = <0x45>; |
| shunt-resistor = <5000>; |
| }; |
| }; |
| i2c@2 { /* NC */ /* FIXME maybe remove */ |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <2>; |
| }; |
| pmbus2_ina226_i2c: i2c@3 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <3>; |
| /* FIXME check alerts coming to SC */ |
| vccaux: ina226@40 { /* u166 */ |
| compatible = "ti,ina226"; |
| reg = <0x40>; |
| shunt-resistor = <5000>; |
| }; |
| vccaux_pmc: ina226@41 { /* u168 */ |
| compatible = "ti,ina226"; |
| reg = <0x41>; |
| shunt-resistor = <5000>; |
| }; |
| mgtavcc: ina226@42 { /* u265 */ |
| compatible = "ti,ina226"; |
| reg = <0x42>; |
| shunt-resistor = <5000>; |
| }; |
| vcc1v5: ina226@43 { /* u264 */ |
| compatible = "ti,ina226"; |
| reg = <0x43>; |
| shunt-resistor = <5000>; |
| }; |
| vcco_mio: ina226@45 { /* u172 */ |
| compatible = "ti,ina226"; |
| reg = <0x45>; |
| shunt-resistor = <5000>; |
| }; |
| mgtavtt: ina226@46 { /* u188 */ |
| compatible = "ti,ina226"; |
| reg = <0x46>; |
| shunt-resistor = <2000>; |
| }; |
| vcco_502: ina226@47 { /* u174 */ |
| compatible = "ti,ina226"; |
| reg = <0x47>; |
| shunt-resistor = <5000>; |
| }; |
| mgtvccaux: ina226@48 { /* u176 */ |
| compatible = "ti,ina226"; |
| reg = <0x48>; |
| shunt-resistor = <5000>; |
| }; |
| vcc1v1_lp4: ina226@49 { /* u186 */ |
| compatible = "ti,ina226"; |
| reg = <0x49>; |
| shunt-resistor = <2000>; |
| }; |
| vadj_fmc: ina226@4a { /* u184 */ |
| compatible = "ti,ina226"; |
| reg = <0x4a>; |
| shunt-resistor = <2000>; |
| }; |
| lpdmgtyavcc: ina226@4b { /* u177 */ |
| compatible = "ti,ina226"; |
| reg = <0x4b>; |
| shunt-resistor = <5000>; |
| }; |
| lpdmgtyavtt: ina226@4c { /* u260 */ |
| compatible = "ti,ina226"; |
| reg = <0x4c>; |
| shunt-resistor = <2000>; |
| }; |
| lpdmgtyvccaux: ina226@4d { /* u234 */ |
| compatible = "ti,ina226"; |
| reg = <0x4d>; |
| shunt-resistor = <5000>; |
| }; |
| }; |
| i2c@4 { /* NC */ |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <4>; |
| }; |
| i2c@5 { /* NC */ |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <5>; |
| }; |
| user_si570: i2c@6 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <6>; |
| user_si570_1: clock-generator@5f { /* USER C0 SI570 - u205 */ |
| #clock-cells = <0>; |
| compatible = "silabs,si570"; |
| reg = <0x5f>; |
| temperature-stability = <50>; |
| factory-fout = <100000000>; |
| clock-frequency = <100000000>; |
| clock-output-names = "fmc_si570"; |
| }; |
| |
| }; |
| /* 7 unused */ |
| }; |
| }; |
| |
| &i2c1 { /* i2c1 MIO 36-37 */ |
| status = "okay"; |
| clock-frequency = <400000>; |
| pinctrl-names = "default", "gpio"; |
| pinctrl-0 = <&pinctrl_i2c1_default>; |
| pinctrl-1 = <&pinctrl_i2c1_gpio>; |
| scl-gpios = <&gpio 36 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| sda-gpios = <&gpio 37 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; |
| |
| i2c-mux@74 { /* u35 */ |
| compatible = "nxp,pca9548"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x74>; |
| /* reset-gpios = <&gpio SYSCTLR_IIC_MUX1_RESET_B GPIO_ACTIVE_HIGH>; */ |
| ref_clk_i2c: i2c@0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0>; |
| /* Use for storing information about SC board */ |
| eeprom: eeprom@54 { /* u34 - m24128 16kB */ |
| compatible = "st,24c128", "atmel,24c128"; |
| reg = <0x54>; /* & 0x5c */ |
| }; |
| ref_clk: clock-generator@5d { /* u32 */ |
| #clock-cells = <0>; |
| compatible = "silabs,si570"; |
| reg = <0x5d>; |
| temperature-stability = <50>; |
| factory-fout = <33333333>; |
| clock-frequency = <33333333>; |
| clock-output-names = "ref_clk"; |
| silabs,skip-recall; |
| }; |
| }; |
| fmcp1_i2c: i2c@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <1>; |
| /* FIXME connection to Samtec J51C */ |
| /* expected eeprom 0x50 SE cards */ |
| }; |
| i2c@2 { /* NC - FIXME */ |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <2>; |
| }; |
| lpddr4_si570_clk3_i2c: i2c@3 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <3>; |
| lpddr4_clk3: clock-generator@60 { /* u4 */ |
| #clock-cells = <0>; |
| compatible = "silabs,si570"; |
| reg = <0x60>; |
| temperature-stability = <50>; |
| factory-fout = <200000000>; |
| clock-frequency = <200000000>; |
| clock-output-names = "lpddr4_clk3"; |
| }; |
| }; |
| lpddr4_si570_clk2_i2c: i2c@4 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <4>; |
| lpddr4_clk2: clock-generator@60 { /* u3 */ |
| #clock-cells = <0>; |
| compatible = "silabs,si570"; |
| reg = <0x60>; |
| temperature-stability = <50>; |
| factory-fout = <200000000>; |
| clock-frequency = <200000000>; |
| clock-output-names = "lpddr4_clk2"; |
| }; |
| }; |
| lpddr4_si570_clk1_i2c: i2c@5 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <5>; |
| lpddr4_clk1: clock-generator@60 { /* u248 */ |
| #clock-cells = <0>; |
| compatible = "silabs,si570"; |
| reg = <0x60>; |
| temperature-stability = <50>; |
| factory-fout = <200000000>; |
| clock-frequency = <200000000>; |
| clock-output-names = "lpddr4_clk1"; |
| }; |
| }; |
| qsfpdd_i2c: i2c@6 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <6>; |
| /* J1/J2 connectors */ |
| }; |
| idt8a34001_i2c: i2c@7 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <7>; |
| /* Via J310 connector */ |
| idt_8a34001: phc@5b { |
| compatible = "idt,8a34001"; /* u219B */ |
| reg = <0x5b>; /* FIXME not in schematics */ |
| }; |
| }; |
| }; |
| }; |
| |
| &usb0 { /* MIO52 - MIO63 */ |
| status = "okay"; |
| phy-names = "usb3-phy"; |
| phys = <&psgtr 1 PHY_TYPE_USB3 0 1>; |
| }; |
| |
| &psgtr { |
| status = "okay"; |
| /* sgmii, usb3 */ |
| clocks = <&si5332_1>, <&si5332_2>; |
| clock-names = "ref0", "ref1"; |
| }; |
| |
| &dwc3_0 { |
| status = "okay"; |
| dr_mode = "peripheral"; |
| snps,dis_u2_susphy_quirk; |
| snps,dis_u3_susphy_quirk; |
| maximum-speed = "super-speed"; |
| }; |
| |
| &xilinx_ams { |
| status = "okay"; |
| }; |
| |
| &ams_ps { |
| status = "okay"; |
| }; |
| |
| &ams_pl { |
| status = "okay"; |
| }; |
| |
| &pinctrl0 { |
| status = "okay"; |
| pinctrl_i2c0_default: i2c0-default { |
| mux { |
| groups = "i2c0_8_grp"; |
| function = "i2c0"; |
| }; |
| |
| conf { |
| groups = "i2c0_8_grp"; |
| bias-pull-up; |
| slew-rate = <SLEW_RATE_SLOW>; |
| power-source = <IO_STANDARD_LVCMOS18>; |
| }; |
| }; |
| |
| pinctrl_i2c0_gpio: i2c0-gpio-grp { |
| mux { |
| groups = "gpio0_34_grp", "gpio0_35_grp"; |
| function = "gpio0"; |
| }; |
| |
| conf { |
| groups = "gpio0_34_grp", "gpio0_35_grp"; |
| slew-rate = <SLEW_RATE_SLOW>; |
| power-source = <IO_STANDARD_LVCMOS18>; |
| }; |
| }; |
| |
| pinctrl_i2c1_default: i2c1-default { |
| mux { |
| groups = "i2c1_9_grp"; |
| function = "i2c1"; |
| }; |
| |
| conf { |
| groups = "i2c1_9_grp"; |
| bias-pull-up; |
| slew-rate = <SLEW_RATE_SLOW>; |
| power-source = <IO_STANDARD_LVCMOS18>; |
| }; |
| }; |
| |
| pinctrl_i2c1_gpio: i2c1-gpio-grp { |
| mux { |
| groups = "gpio0_36_grp", "gpio0_37_grp"; |
| function = "gpio0"; |
| }; |
| |
| conf { |
| groups = "gpio0_36_grp", "gpio0_37_grp"; |
| slew-rate = <SLEW_RATE_SLOW>; |
| power-source = <IO_STANDARD_LVCMOS18>; |
| }; |
| }; |
| }; |