| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (C) 2020 Marvell International Ltd. |
| */ |
| |
| #include <i2c.h> |
| #include <ram.h> |
| |
| #include <mach/octeon_ddr.h> |
| |
| #define DEVICE_TYPE DDR4_SPD_KEY_BYTE_DEVICE_TYPE // same for DDR3 and DDR4 |
| #define MODULE_TYPE DDR4_SPD_KEY_BYTE_MODULE_TYPE // same for DDR3 and DDR4 |
| #define BUS_WIDTH(t) (((t) == DDR4_DRAM) ? \ |
| DDR4_SPD_MODULE_MEMORY_BUS_WIDTH : \ |
| DDR3_SPD_MEMORY_BUS_WIDTH) |
| |
| /* |
| * Allow legacy code to encode bus number in the upper bits of the address |
| * These are only supported in read_spd() |
| */ |
| #define OCTEON_TWSI_BUS_IN_ADDR_BIT 12 |
| #define OCTEON_TWSI_BUS_IN_ADDR_MASK (15 << OCTEON_TWSI_BUS_IN_ADDR_BIT) |
| #define OCTEON_TWSI_GET_BUS(addr) \ |
| (((addr) >> OCTEON_TWSI_BUS_IN_ADDR_BIT) & 0xf) |
| |
| const char *ddr3_dimm_types[] = { |
| /* 0000 */ "Undefined", |
| /* 0001 */ "RDIMM", |
| /* 0010 */ "UDIMM", |
| /* 0011 */ "SO-DIMM", |
| /* 0100 */ "Micro-DIMM", |
| /* 0101 */ "Mini-RDIMM", |
| /* 0110 */ "Mini-UDIMM", |
| /* 0111 */ "Mini-CDIMM", |
| /* 1000 */ "72b-SO-UDIMM", |
| /* 1001 */ "72b-SO-RDIMM", |
| /* 1010 */ "72b-SO-CDIMM" |
| /* 1011 */ "LRDIMM", |
| /* 1100 */ "16b-SO-DIMM", |
| /* 1101 */ "32b-SO-DIMM", |
| /* 1110 */ "Reserved", |
| /* 1111 */ "Reserved" |
| }; |
| |
| const char *ddr4_dimm_types[] = { |
| /* 0000 */ "Extended", |
| /* 0001 */ "RDIMM", |
| /* 0010 */ "UDIMM", |
| /* 0011 */ "SO-DIMM", |
| /* 0100 */ "LRDIMM", |
| /* 0101 */ "Mini-RDIMM", |
| /* 0110 */ "Mini-UDIMM", |
| /* 0111 */ "Reserved", |
| /* 1000 */ "72b-SO-RDIMM", |
| /* 1001 */ "72b-SO-UDIMM", |
| /* 1010 */ "Reserved", |
| /* 1011 */ "Reserved", |
| /* 1100 */ "16b-SO-DIMM", |
| /* 1101 */ "32b-SO-DIMM", |
| /* 1110 */ "Reserved", |
| /* 1111 */ "Reserved" |
| }; |
| |
| static u16 ddr3_crc16(u8 *ptr, int count) |
| { |
| /* From DDR3 SPD specification */ |
| int crc, i; |
| |
| crc = 0; |
| while (--count >= 0) { |
| crc = crc ^ (int)*ptr++ << 8; |
| for (i = 0; i < 8; ++i) { |
| if (crc & 0x8000) |
| crc = crc << 1 ^ 0x1021; |
| else |
| crc = crc << 1; |
| } |
| } |
| |
| return (crc & 0xFFFF); |
| } |
| |
| static int validate_spd_checksum_ddr4(struct dimm_config *dimm_config, |
| int dimm_index, int twsi_addr, int silent) |
| { |
| u8 *spd_data = dimm_config->spd_data[dimm_index]; |
| int crc_bytes = 126; |
| u16 crc_comp; |
| |
| /* Check byte 0 to see how many bytes checksum is over */ |
| if (spd_data[0] & 0x80) |
| crc_bytes = 117; |
| |
| crc_comp = ddr3_crc16(spd_data, crc_bytes); |
| |
| if (spd_data[126] == (crc_comp & 0xff) && |
| spd_data[127] == (crc_comp >> 8)) |
| return 1; |
| |
| if (!silent) { |
| printf("DDR4 SPD CRC error, spd addr: 0x%x, calculated crc: 0x%04x, read crc: 0x%02x%02x\n", |
| twsi_addr, crc_comp, spd_data[127], spd_data[126]); |
| } |
| |
| return 0; |
| } |
| |
| static int validate_spd_checksum(struct ddr_priv *priv, |
| struct dimm_config *dimm_config, |
| int dimm_index, int twsi_addr, |
| int silent, u8 rv) |
| { |
| if (ddr_verbose(priv)) |
| debug("Validating DIMM at address 0x%x\n", twsi_addr); |
| |
| if (rv >= 0x8 && rv <= 0xA) |
| printf("%s: Error: DDR2 support disabled\n", __func__); |
| |
| if (rv == 0xB) |
| printf("%s: Error: DDR3 support disabled\n", __func__); |
| |
| if (rv == 0xC) { |
| return validate_spd_checksum_ddr4(dimm_config, dimm_index, |
| twsi_addr, silent); |
| } |
| |
| if (!silent) { |
| printf("Unrecognized DIMM type: 0x%x at spd address: 0x%x\n", |
| rv, twsi_addr); |
| } |
| |
| return 0; |
| } |
| |
| /* |
| * Read an DIMM SPD value, either using TWSI to read it from the DIMM, or |
| * from a provided array. |
| */ |
| int read_spd(struct dimm_config *dimm_config, int dimm_index, int spd_field) |
| { |
| dimm_index = !!dimm_index; |
| |
| if (spd_field >= SPD_EEPROM_SIZE) { |
| printf("ERROR: Trying to read unsupported SPD EEPROM value %d\n", |
| spd_field); |
| } |
| |
| /* |
| * If pointer to data is provided, use it, otherwise read from SPD |
| * over twsi |
| */ |
| if (dimm_config->spd_ptrs[dimm_index]) |
| return dimm_config->spd_ptrs[dimm_index][spd_field]; |
| else if (dimm_config->spd_addrs[dimm_index]) |
| return dimm_config->spd_data[dimm_index][spd_field]; |
| |
| return -1; |
| } |
| |
| int read_spd_init(struct dimm_config *dimm_config, int dimm_index) |
| { |
| u8 busno = OCTEON_TWSI_GET_BUS(dimm_config->spd_addrs[dimm_index]); |
| u8 cmdno = dimm_config->spd_addrs[dimm_index]; |
| struct udevice *dev_i2c; |
| u8 *spd_data; |
| int ret; |
| |
| if (dimm_config->spd_cached[dimm_index]) |
| return 0; |
| |
| dimm_config->spd_cached[dimm_index] = 1; |
| spd_data = dimm_config->spd_data[dimm_index]; |
| |
| ret = i2c_get_chip_for_busnum(busno, cmdno, 2, &dev_i2c); |
| if (ret) { |
| debug("Cannot find SPL EEPROM: %d\n", ret); |
| return -ENODEV; |
| } |
| |
| ret = dm_i2c_read(dev_i2c, 0, spd_data, SPD_EEPROM_SIZE); |
| |
| return ret; |
| } |
| |
| int validate_dimm(struct ddr_priv *priv, struct dimm_config *dimm_config, |
| int dimm_index) |
| { |
| int spd_addr; |
| |
| dimm_index = !!dimm_index; /* Normalize to 0/1 */ |
| spd_addr = dimm_config->spd_addrs[dimm_index]; |
| |
| debug("Validating dimm %d, spd addr: 0x%02x spd ptr: %p\n", |
| dimm_index, |
| dimm_config->spd_addrs[dimm_index], |
| dimm_config->spd_ptrs[dimm_index]); |
| |
| /* Only validate 'real' dimms, assume compiled in values are OK */ |
| if (!dimm_config->spd_ptrs[dimm_index]) { |
| int val0, val1; |
| int dimm_type; |
| int ret; |
| |
| ret = read_spd_init(dimm_config, dimm_index); |
| if (ret) |
| return 0; |
| |
| dimm_type = read_spd(dimm_config, dimm_index, |
| DDR2_SPD_MEM_TYPE) & 0xff; |
| switch (dimm_type) { |
| case 0x0B: /* DDR3 */ |
| if (ddr_verbose(priv)) |
| printf("Validating DDR3 DIMM %d\n", dimm_index); |
| val0 = read_spd(dimm_config, dimm_index, |
| DDR3_SPD_DENSITY_BANKS); |
| val1 = read_spd(dimm_config, dimm_index, |
| DDR3_SPD_ADDRESSING_ROW_COL_BITS); |
| if (val0 < 0 && val1 < 0) { |
| if (ddr_verbose(priv)) |
| printf("Error reading SPD for DIMM %d\n", |
| dimm_index); |
| return 0; /* Failed to read dimm */ |
| } |
| if (val0 == 0xff && val1 == 0xff) { |
| if (ddr_verbose(priv)) |
| printf("Blank or unreadable SPD for DIMM %d\n", |
| dimm_index); |
| /* Blank SPD or otherwise unreadable device */ |
| return 0; |
| } |
| |
| /* Don't treat bad checksums as fatal */ |
| validate_spd_checksum(priv, dimm_config, dimm_index, |
| spd_addr, 0, dimm_type); |
| break; |
| |
| case 0x0C: /* DDR4 */ |
| if (ddr_verbose(priv)) |
| printf("Validating DDR4 DIMM %d\n", dimm_index); |
| val0 = read_spd(dimm_config, dimm_index, |
| DDR4_SPD_DENSITY_BANKS); |
| val1 = read_spd(dimm_config, dimm_index, |
| DDR4_SPD_ADDRESSING_ROW_COL_BITS); |
| if (val0 < 0 && val1 < 0) { |
| if (ddr_verbose(priv)) |
| printf("Error reading SPD for DIMM %d\n", |
| dimm_index); |
| return 0; /* Failed to read dimm */ |
| } |
| if (val0 == 0xff && val1 == 0xff) { |
| if (ddr_verbose(priv)) { |
| printf("Blank or unreadable SPD for DIMM %d\n", |
| dimm_index); |
| } |
| /* Blank SPD or otherwise unreadable device */ |
| return 0; |
| } |
| |
| /* Don't treat bad checksums as fatal */ |
| validate_spd_checksum(priv, dimm_config, dimm_index, |
| spd_addr, 0, dimm_type); |
| break; |
| |
| case 0x00: |
| /* Terminator detected. Fail silently. */ |
| return 0; |
| |
| default: |
| debug("Unknown DIMM type 0x%x for DIMM %d @ 0x%x\n", |
| dimm_type, dimm_index, |
| dimm_config->spd_addrs[dimm_index]); |
| return 0; /* Failed to read dimm */ |
| } |
| } |
| |
| return 1; |
| } |
| |
| int get_ddr_type(struct dimm_config *dimm_config, int upper_dimm) |
| { |
| int spd_ddr_type; |
| |
| spd_ddr_type = read_spd(dimm_config, upper_dimm, DEVICE_TYPE); |
| |
| debug("%s:%d spd_ddr_type=0x%02x\n", __func__, __LINE__, |
| spd_ddr_type); |
| |
| /* we return only DDR4 or DDR3 */ |
| return (spd_ddr_type == 0x0C) ? DDR4_DRAM : DDR3_DRAM; |
| } |
| |
| static int get_dimm_ecc(struct dimm_config *dimm_config, int upper_dimm, |
| int ddr_type) |
| { |
| return !!(read_spd(dimm_config, upper_dimm, BUS_WIDTH(ddr_type)) & 8); |
| } |
| |
| int get_dimm_module_type(struct dimm_config *dimm_config, int upper_dimm, |
| int ddr_type) |
| { |
| return read_spd(dimm_config, upper_dimm, MODULE_TYPE) & 0x0f; |
| } |
| |
| char *printable_rank_spec(char *buffer, int num_ranks, int dram_width, |
| int spd_package) |
| { |
| int die_count = ((spd_package >> 4) & 7) + 1; |
| |
| if (spd_package & 0x80) { // non-monolithic |
| if ((spd_package & 3) == 2) { // 3DS |
| sprintf(buffer, "%dS%dRx%d", num_ranks, die_count, |
| dram_width); |
| } else { // MLS |
| char hchar = (die_count == 2) ? 'D' : 'Q'; |
| |
| sprintf(buffer, "%d%cRx%d", num_ranks, hchar, |
| dram_width); |
| } |
| } else { |
| sprintf(buffer, "%dRx%d", num_ranks, dram_width); |
| } |
| |
| return buffer; |
| } |
| |
| static void report_common_dimm(struct dimm_config *dimm_config, int upper_dimm, |
| int dimm, const char **dimm_types, int ddr_type, |
| char *volt_str, int if_num, |
| int num_ranks, int dram_width, int spd_package) |
| { |
| unsigned int spd_module_type; |
| char rank_spec[8]; |
| int spd_ecc; |
| |
| spd_module_type = get_dimm_module_type(dimm_config, upper_dimm, |
| ddr_type); |
| spd_ecc = get_dimm_ecc(dimm_config, upper_dimm, ddr_type); |
| |
| printable_rank_spec(rank_spec, num_ranks, dram_width, spd_package); |
| printf("LMC%d.DIMM%d: DDR%d %s %s %s, %s\n", |
| if_num, dimm, ddr_type, dimm_types[spd_module_type], |
| rank_spec, spd_ecc ? "ECC" : "non-ECC", volt_str); |
| } |
| |
| static void report_ddr3_dimm(struct dimm_config *dimm_config, int upper_dimm, |
| int dimm, int if_num) |
| { |
| int spd_voltage; |
| char *volt_str; |
| int spd_org = read_spd(dimm_config, upper_dimm, |
| DDR3_SPD_MODULE_ORGANIZATION); |
| int num_ranks = 1 + ((spd_org >> 3) & 0x7); |
| int dram_width = 4 << ((spd_org >> 0) & 0x7); |
| |
| spd_voltage = read_spd(dimm_config, upper_dimm, |
| DDR3_SPD_NOMINAL_VOLTAGE); |
| if (spd_voltage == 0 || spd_voltage & 3) |
| volt_str = "1.5V"; |
| if (spd_voltage & 2) |
| volt_str = "1.35V"; |
| if (spd_voltage & 4) |
| volt_str = "1.2xV"; |
| |
| report_common_dimm(dimm_config, upper_dimm, dimm, ddr3_dimm_types, |
| DDR3_DRAM, volt_str, if_num, |
| num_ranks, dram_width, /*spd_package*/0); |
| } |
| |
| static void report_ddr4_dimm(struct dimm_config *dimm_config, int upper_dimm, |
| int dimm, int if_num) |
| { |
| int spd_voltage; |
| char *volt_str; |
| int spd_package = 0xff & read_spd(dimm_config, upper_dimm, |
| DDR4_SPD_PACKAGE_TYPE); |
| int spd_org = 0xff & read_spd(dimm_config, upper_dimm, |
| DDR4_SPD_MODULE_ORGANIZATION); |
| int num_ranks = 1 + ((spd_org >> 3) & 0x7); |
| int dram_width = 4 << ((spd_org >> 0) & 0x7); |
| |
| spd_voltage = read_spd(dimm_config, upper_dimm, |
| DDR4_SPD_MODULE_NOMINAL_VOLTAGE); |
| if (spd_voltage == 0x01 || spd_voltage & 0x02) |
| volt_str = "1.2V"; |
| if (spd_voltage == 0x04 || spd_voltage & 0x08) |
| volt_str = "TBD1 V"; |
| if (spd_voltage == 0x10 || spd_voltage & 0x20) |
| volt_str = "TBD2 V"; |
| |
| report_common_dimm(dimm_config, upper_dimm, dimm, ddr4_dimm_types, |
| DDR4_DRAM, volt_str, if_num, |
| num_ranks, dram_width, spd_package); |
| } |
| |
| void report_dimm(struct dimm_config *dimm_config, int upper_dimm, |
| int dimm, int if_num) |
| { |
| int ddr_type; |
| |
| /* ddr_type only indicates DDR4 or DDR3 */ |
| ddr_type = get_ddr_type(dimm_config, upper_dimm); |
| |
| if (ddr_type == DDR4_DRAM) |
| report_ddr4_dimm(dimm_config, 0, dimm, if_num); |
| else |
| report_ddr3_dimm(dimm_config, 0, dimm, if_num); |
| } |