| /* |
| * Copyright (C) 2007-2010 Freescale Semiconductor, Inc. |
| * |
| * Dave Liu <daveliu@freescale.com> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #define CONFIG_DISPLAY_BOARDINFO |
| |
| #define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) |
| #define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000 |
| #define CONFIG_SYS_NAND_U_BOOT_START 0x00100100 |
| #define CONFIG_SYS_NAND_U_BOOT_OFFS 16384 |
| #define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000 |
| |
| #ifndef CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_TEXT_BASE 0xFE000000 |
| #endif |
| |
| #ifndef CONFIG_SYS_MONITOR_BASE |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ |
| #endif |
| |
| /* |
| * High Level Configuration Options |
| */ |
| #define CONFIG_E300 1 /* E300 family */ |
| #define CONFIG_MPC831x 1 /* MPC831x CPU family */ |
| #define CONFIG_MPC8315 1 /* MPC8315 CPU specific */ |
| #define CONFIG_MPC8315ERDB 1 /* MPC8315ERDB board specific */ |
| |
| /* |
| * System Clock Setup |
| */ |
| #define CONFIG_83XX_CLKIN 66666667 /* in Hz */ |
| #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN |
| |
| /* |
| * Hardware Reset Configuration Word |
| * if CLKIN is 66.66MHz, then |
| * CSB = 133MHz, CORE = 400MHz, DDRC = 266MHz, LBC = 133MHz |
| */ |
| #define CONFIG_SYS_HRCW_LOW (\ |
| HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ |
| HRCWL_DDR_TO_SCB_CLK_2X1 |\ |
| HRCWL_SVCOD_DIV_2 |\ |
| HRCWL_CSB_TO_CLKIN_2X1 |\ |
| HRCWL_CORE_TO_CSB_3X1) |
| #define CONFIG_SYS_HRCW_HIGH_BASE (\ |
| HRCWH_PCI_HOST |\ |
| HRCWH_PCI1_ARBITER_ENABLE |\ |
| HRCWH_CORE_ENABLE |\ |
| HRCWH_BOOTSEQ_DISABLE |\ |
| HRCWH_SW_WATCHDOG_DISABLE |\ |
| HRCWH_TSEC1M_IN_RGMII |\ |
| HRCWH_TSEC2M_IN_RGMII |\ |
| HRCWH_BIG_ENDIAN |\ |
| HRCWH_LALE_NORMAL) |
| |
| #ifdef CONFIG_NAND_SPL |
| #define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\ |
| HRCWH_FROM_0XFFF00100 |\ |
| HRCWH_ROM_LOC_NAND_SP_8BIT |\ |
| HRCWH_RL_EXT_NAND) |
| #else |
| #define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\ |
| HRCWH_FROM_0X00000100 |\ |
| HRCWH_ROM_LOC_LOCAL_16BIT |\ |
| HRCWH_RL_EXT_LEGACY) |
| #endif |
| |
| /* |
| * System IO Config |
| */ |
| #define CONFIG_SYS_SICRH 0x00000000 |
| #define CONFIG_SYS_SICRL 0x00000000 /* 3.3V, no delay */ |
| |
| #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ |
| #define CONFIG_HWCONFIG |
| |
| /* |
| * IMMR new address |
| */ |
| #define CONFIG_SYS_IMMR 0xE0000000 |
| |
| /* |
| * Arbiter Setup |
| */ |
| #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ |
| #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ |
| #define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ |
| |
| /* |
| * DDR Setup |
| */ |
| #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE |
| #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE |
| #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 |
| #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ |
| | DDRCDR_PZ_LOZ \ |
| | DDRCDR_NZ_LOZ \ |
| | DDRCDR_ODT \ |
| | DDRCDR_Q_DRN) |
| /* 0x7b880001 */ |
| /* |
| * Manually set up DDR parameters |
| * consist of two chips HY5PS12621BFP-C4 from HYNIX |
| */ |
| #define CONFIG_SYS_DDR_SIZE 128 /* MB */ |
| #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 |
| #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ |
| | CSCONFIG_ODT_RD_NEVER \ |
| | CSCONFIG_ODT_WR_ONLY_CURRENT \ |
| | CSCONFIG_ROW_BIT_13 \ |
| | CSCONFIG_COL_BIT_10) |
| /* 0x80010102 */ |
| #define CONFIG_SYS_DDR_TIMING_3 0x00000000 |
| #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ |
| | (0 << TIMING_CFG0_WRT_SHIFT) \ |
| | (0 << TIMING_CFG0_RRT_SHIFT) \ |
| | (0 << TIMING_CFG0_WWT_SHIFT) \ |
| | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ |
| | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ |
| | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ |
| | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) |
| /* 0x00220802 */ |
| #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ |
| | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \ |
| | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ |
| | (5 << TIMING_CFG1_CASLAT_SHIFT) \ |
| | (6 << TIMING_CFG1_REFREC_SHIFT) \ |
| | (2 << TIMING_CFG1_WRREC_SHIFT) \ |
| | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ |
| | (2 << TIMING_CFG1_WRTORD_SHIFT)) |
| /* 0x27256222 */ |
| #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \ |
| | (4 << TIMING_CFG2_CPO_SHIFT) \ |
| | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ |
| | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ |
| | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ |
| | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ |
| | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) |
| /* 0x121048c5 */ |
| #define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \ |
| | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) |
| /* 0x03600100 */ |
| #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ |
| | SDRAM_CFG_SDRAM_TYPE_DDR2 \ |
| | SDRAM_CFG_DBW_32) |
| /* 0x43080000 */ |
| #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ |
| #define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \ |
| | (0x0232 << SDRAM_MODE_SD_SHIFT)) |
| /* ODT 150ohm CL=3, AL=1 on SDRAM */ |
| #define CONFIG_SYS_DDR_MODE2 0x00000000 |
| |
| /* |
| * Memory test |
| */ |
| #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ |
| #define CONFIG_SYS_MEMTEST_START 0x00040000 /* memtest region */ |
| #define CONFIG_SYS_MEMTEST_END 0x00140000 |
| |
| /* |
| * The reserved memory |
| */ |
| #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ |
| #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ |
| |
| /* |
| * Initial RAM Base Address Setup |
| */ |
| #define CONFIG_SYS_INIT_RAM_LOCK 1 |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ |
| #define CONFIG_SYS_GBL_DATA_OFFSET \ |
| (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| |
| /* |
| * Local Bus Configuration & Clock Setup |
| */ |
| #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP |
| #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 |
| #define CONFIG_SYS_LBC_LBCR 0x00040000 |
| #define CONFIG_FSL_ELBC 1 |
| |
| /* |
| * FLASH on the Local Bus |
| */ |
| #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ |
| #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ |
| #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT |
| |
| #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ |
| #define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is 8M */ |
| #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ |
| |
| /* Window base at flash base */ |
| #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE |
| #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB) |
| |
| #define CONFIG_SYS_NOR_BR_PRELIM (CONFIG_SYS_FLASH_BASE \ |
| | BR_PS_16 /* 16 bit port */ \ |
| | BR_MS_GPCM /* MSEL = GPCM */ \ |
| | BR_V) /* valid */ |
| #define CONFIG_SYS_NOR_OR_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ |
| | OR_UPM_XAM \ |
| | OR_GPCM_CSNT \ |
| | OR_GPCM_ACS_DIV2 \ |
| | OR_GPCM_XACS \ |
| | OR_GPCM_SCY_15 \ |
| | OR_GPCM_TRLX_SET \ |
| | OR_GPCM_EHTR_SET \ |
| | OR_GPCM_EAD) |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ |
| /* 127 64KB sectors and 8 8KB top sectors per device */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 135 |
| |
| #undef CONFIG_SYS_FLASH_CHECKSUM |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| |
| /* |
| * NAND Flash on the Local Bus |
| */ |
| |
| #ifdef CONFIG_NAND_SPL |
| #define CONFIG_SYS_NAND_BASE 0xFFF00000 |
| #else |
| #define CONFIG_SYS_NAND_BASE 0xE0600000 |
| #endif |
| |
| #define CONFIG_MTD_DEVICE |
| #define CONFIG_MTD_PARTITION |
| #define CONFIG_CMD_MTDPARTS |
| #define MTDIDS_DEFAULT "nand0=e0600000.flash" |
| #define MTDPARTS_DEFAULT \ |
| "mtdparts=e0600000.flash:512k(uboot),128k(env),3m@1m(kernel),-(fs)" |
| |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_CMD_NAND 1 |
| #define CONFIG_NAND_FSL_ELBC 1 |
| #define CONFIG_SYS_NAND_BLOCK_SIZE 16384 |
| #define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024) /* 0x00008000 */ |
| |
| #define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) |
| #define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000 |
| #define CONFIG_SYS_NAND_U_BOOT_START 0x00100100 |
| #define CONFIG_SYS_NAND_U_BOOT_OFFS 16384 |
| #define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000 |
| |
| #define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE \ |
| | BR_DECC_CHK_GEN /* Use HW ECC */ \ |
| | BR_PS_8 /* 8 bit port */ \ |
| | BR_MS_FCM /* MSEL = FCM */ \ |
| | BR_V) /* valid */ |
| #define CONFIG_SYS_NAND_OR_PRELIM \ |
| (P2SZ_TO_AM(CONFIG_SYS_NAND_WINDOW_SIZE) \ |
| | OR_FCM_CSCT \ |
| | OR_FCM_CST \ |
| | OR_FCM_CHT \ |
| | OR_FCM_SCY_1 \ |
| | OR_FCM_TRLX \ |
| | OR_FCM_EHTR) |
| /* 0xFFFF8396 */ |
| |
| #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM |
| #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM |
| #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM |
| #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM |
| |
| #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE |
| #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) |
| |
| #define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM |
| #define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM |
| |
| #if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE && \ |
| !defined(CONFIG_NAND_SPL) |
| #define CONFIG_SYS_RAMBOOT |
| #else |
| #undef CONFIG_SYS_RAMBOOT |
| #endif |
| |
| /* |
| * Serial Port |
| */ |
| #define CONFIG_CONS_INDEX 1 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 2) |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) |
| |
| /* I2C */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_FSL |
| #define CONFIG_SYS_FSL_I2C_SPEED 400000 |
| #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 |
| #define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } |
| |
| /* |
| * Board info - revision and where boot from |
| */ |
| #define CONFIG_SYS_I2C_PCF8574A_ADDR 0x39 |
| |
| /* |
| * Config on-board RTC |
| */ |
| #define CONFIG_RTC_DS1337 /* ds1339 on board, use ds1337 rtc via i2c */ |
| #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ |
| |
| /* |
| * General PCI |
| * Addresses are mapped 1-1. |
| */ |
| #define CONFIG_SYS_PCI_MEM_BASE 0x80000000 |
| #define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE |
| #define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */ |
| #define CONFIG_SYS_PCI_MMIO_BASE 0x90000000 |
| #define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE |
| #define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */ |
| #define CONFIG_SYS_PCI_IO_BASE 0x00000000 |
| #define CONFIG_SYS_PCI_IO_PHYS 0xE0300000 |
| #define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */ |
| |
| #define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE |
| #define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 |
| #define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000 |
| |
| #define CONFIG_SYS_PCIE1_BASE 0xA0000000 |
| #define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 |
| #define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 |
| #define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 |
| #define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 |
| #define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 |
| #define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 |
| #define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 |
| #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 |
| |
| #define CONFIG_SYS_PCIE2_BASE 0xC0000000 |
| #define CONFIG_SYS_PCIE2_MEM_BASE 0xC0000000 |
| #define CONFIG_SYS_PCIE2_MEM_PHYS 0xC0000000 |
| #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 |
| #define CONFIG_SYS_PCIE2_CFG_BASE 0xD0000000 |
| #define CONFIG_SYS_PCIE2_CFG_SIZE 0x01000000 |
| #define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 |
| #define CONFIG_SYS_PCIE2_IO_PHYS 0xD1000000 |
| #define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 |
| |
| #define CONFIG_PCI |
| #define CONFIG_PCI_INDIRECT_BRIDGE |
| #define CONFIG_PCIE |
| |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| |
| #define CONFIG_EEPRO100 |
| #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ |
| |
| #define CONFIG_HAS_FSL_DR_USB |
| #define CONFIG_SYS_SCCR_USBDRCM 3 |
| |
| #define CONFIG_USB_STORAGE |
| #define CONFIG_USB_EHCI |
| #define CONFIG_USB_EHCI_FSL |
| #define CONFIG_USB_PHY_TYPE "utmi" |
| #define CONFIG_EHCI_HCD_INIT_AFTER_RESET |
| |
| /* |
| * TSEC |
| */ |
| #define CONFIG_TSEC_ENET /* TSEC ethernet support */ |
| #define CONFIG_SYS_TSEC1_OFFSET 0x24000 |
| #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) |
| #define CONFIG_SYS_TSEC2_OFFSET 0x25000 |
| #define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) |
| |
| /* |
| * TSEC ethernet configuration |
| */ |
| #define CONFIG_MII 1 /* MII PHY management */ |
| #define CONFIG_TSEC1 1 |
| #define CONFIG_TSEC1_NAME "eTSEC0" |
| #define CONFIG_TSEC2 1 |
| #define CONFIG_TSEC2_NAME "eTSEC1" |
| #define TSEC1_PHY_ADDR 0 |
| #define TSEC2_PHY_ADDR 1 |
| #define TSEC1_PHYIDX 0 |
| #define TSEC2_PHYIDX 0 |
| #define TSEC1_FLAGS TSEC_GIGABIT |
| #define TSEC2_FLAGS TSEC_GIGABIT |
| |
| /* Options are: eTSEC[0-1] */ |
| #define CONFIG_ETHPRIME "eTSEC1" |
| |
| /* |
| * SATA |
| */ |
| #define CONFIG_LIBATA |
| #define CONFIG_FSL_SATA |
| |
| #define CONFIG_SYS_SATA_MAX_DEVICE 2 |
| #define CONFIG_SATA1 |
| #define CONFIG_SYS_SATA1_OFFSET 0x18000 |
| #define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET) |
| #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA |
| #define CONFIG_SATA2 |
| #define CONFIG_SYS_SATA2_OFFSET 0x19000 |
| #define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET) |
| #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA |
| |
| #ifdef CONFIG_FSL_SATA |
| #define CONFIG_LBA48 |
| #define CONFIG_CMD_SATA |
| #define CONFIG_DOS_PARTITION |
| #define CONFIG_CMD_EXT2 |
| #endif |
| |
| /* |
| * Environment |
| */ |
| #if !defined(CONFIG_SYS_RAMBOOT) |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_ADDR \ |
| (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) |
| #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ |
| #define CONFIG_ENV_SIZE 0x2000 |
| #else |
| #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ |
| #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) |
| #define CONFIG_ENV_SIZE 0x2000 |
| #endif |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| /* |
| * Command line configuration. |
| */ |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_PCI |
| |
| #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ |
| #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| |
| /* Print Buffer Size */ |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| /* Boot Argument Buffer Size */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 256 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ |
| |
| /* |
| * Core HID Setup |
| */ |
| #define CONFIG_SYS_HID0_INIT 0x000000000 |
| #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ |
| HID0_ENABLE_INSTRUCTION_CACHE | \ |
| HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) |
| #define CONFIG_SYS_HID2 HID2_HBE |
| |
| /* |
| * MMU Setup |
| */ |
| #define CONFIG_HIGH_BATS 1 /* High BATs supported */ |
| |
| /* DDR: cache cacheable */ |
| #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \ |
| | BATL_PP_RW \ |
| | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ |
| | BATU_BL_128M \ |
| | BATU_VS \ |
| | BATU_VP) |
| #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L |
| #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U |
| |
| /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ |
| #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \ |
| | BATL_PP_RW \ |
| | BATL_CACHEINHIBIT \ |
| | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \ |
| | BATU_BL_8M \ |
| | BATU_VS \ |
| | BATU_VP) |
| #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L |
| #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U |
| |
| /* FLASH: icache cacheable, but dcache-inhibit and guarded */ |
| #define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE \ |
| | BATL_PP_RW \ |
| | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE \ |
| | BATU_BL_32M \ |
| | BATU_VS \ |
| | BATU_VP) |
| #define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE \ |
| | BATL_PP_RW \ |
| | BATL_CACHEINHIBIT \ |
| | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U |
| |
| /* Stack in dcache: cacheable, no memory coherence */ |
| #define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) |
| #define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR \ |
| | BATU_BL_128K \ |
| | BATU_VS \ |
| | BATU_VP) |
| #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L |
| #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U |
| |
| /* PCI MEM space: cacheable */ |
| #define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI_MEM_PHYS \ |
| | BATL_PP_RW \ |
| | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI_MEM_PHYS \ |
| | BATU_BL_256M \ |
| | BATU_VS \ |
| | BATU_VP) |
| #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L |
| #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U |
| |
| /* PCI MMIO space: cache-inhibit and guarded */ |
| #define CONFIG_SYS_IBAT5L (CONFIG_SYS_PCI_MMIO_PHYS \ |
| | BATL_PP_RW \ |
| | BATL_CACHEINHIBIT \ |
| | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_IBAT5U (CONFIG_SYS_PCI_MMIO_PHYS \ |
| | BATU_BL_256M \ |
| | BATU_VS \ |
| | BATU_VP) |
| #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L |
| #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U |
| |
| #define CONFIG_SYS_IBAT6L 0 |
| #define CONFIG_SYS_IBAT6U 0 |
| #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L |
| #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U |
| |
| #define CONFIG_SYS_IBAT7L 0 |
| #define CONFIG_SYS_IBAT7U 0 |
| #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L |
| #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ |
| #endif |
| |
| /* |
| * Environment Configuration |
| */ |
| |
| #define CONFIG_ENV_OVERWRITE |
| |
| #if defined(CONFIG_TSEC_ENET) |
| #define CONFIG_HAS_ETH0 |
| #define CONFIG_HAS_ETH1 |
| #endif |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ |
| |
| #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ |
| #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=eth0\0" \ |
| "consoledev=ttyS0\0" \ |
| "ramdiskaddr=1000000\0" \ |
| "ramdiskfile=ramfs.83xx\0" \ |
| "fdtaddr=780000\0" \ |
| "fdtfile=mpc8315erdb.dtb\0" \ |
| "usb_phy_type=utmi\0" \ |
| "" |
| |
| #define CONFIG_NFSBOOTCOMMAND \ |
| "setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=$serverip:$rootpath " \ |
| "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ |
| "$netdev:off " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr - $fdtaddr" |
| |
| #define CONFIG_RAMBOOTCOMMAND \ |
| "setenv bootargs root=/dev/ram rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $ramdiskaddr $ramdiskfile;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr $ramdiskaddr $fdtaddr" |
| |
| |
| #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND |
| |
| #endif /* __CONFIG_H */ |