include/configs/ti_omap5_common.h - filogic/uboot - Gitiles

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * (C) Copyright 2013
  * Texas Instruments Incorporated.
  * Sricharan R	  <r.sricharan@ti.com>
  *
  * Derived from OMAP4 done by:
  *	Aneesh V <aneesh@ti.com>
  *
  * TI OMAP5 AND DRA7XX common configuration settings
  *
  * For more details, please see the technical documents listed at
  * http://www.ti.com/product/omap5432
  */

 #ifndef __CONFIG_TI_OMAP5_COMMON_H
 #define __CONFIG_TI_OMAP5_COMMON_H

 /* Use General purpose timer 1 */
 #define CONFIG_SYS_TIMERBASE		GPT2_BASE

 #include <linux/stringify.h>

 #include <asm/arch/cpu.h>
 #include <asm/arch/omap.h>

 #include <configs/ti_armv7_omap.h>

 /*
  * Hardware drivers
  */
 #define CFG_SYS_NS16550_CLK		48000000

 /*
  * Environment setup
  */

 #ifndef DFUARGS
 #define DFUARGS
 #endif

 #include <environment/ti/mmc.h>
 #include <environment/ti/nand.h>

 #ifndef CONSOLEDEV
 #define CONSOLEDEV "ttyS2"
 #endif

 #ifndef PARTS_DEFAULT
 /*
  * Default GPT tables for eMMC (Linux and Android). Notes:
  *   1. Keep partitions aligned to erase group size (512 KiB) when possible
  *   2. Keep partitions in sync with DFU_ALT_INFO_EMMC (see dfu.h)
  *   3. Keep 'bootloader' partition (U-Boot proper) start address in sync with
  *      CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR (see common/spl/Kconfig)
  */
 #define PARTS_DEFAULT \
 	/* Linux partitions */ \
 	"uuid_disk=${uuid_gpt_disk};" \
 	"name=bootloader,start=384K,size=1792K,uuid=${uuid_gpt_bootloader};" \
 	"name=rootfs,start=2688K,size=-,uuid=${uuid_gpt_rootfs}\0" \
 	/* Android partitions */ \
 	"partitions_android=" \
 	"uuid_disk=${uuid_gpt_disk};" \
 	"name=xloader,start=128K,size=256K,uuid=${uuid_gpt_xloader};" \
 	"name=bootloader,size=2048K,uuid=${uuid_gpt_bootloader};" \
 	"name=uboot-env,start=2432K,size=256K,uuid=${uuid_gpt_reserved};" \
 	"name=misc,size=128K,uuid=${uuid_gpt_misc};" \
 	"name=boot_a,size=20M,uuid=${uuid_gpt_boot_a};" \
 	"name=boot_b,size=20M,uuid=${uuid_gpt_boot_b};" \
 	"name=dtbo_a,size=8M,uuid=${uuid_gpt_dtbo_a};" \
 	"name=dtbo_b,size=8M,uuid=${uuid_gpt_dtbo_b};" \
 	"name=vbmeta_a,size=64K,uuid=${uuid_gpt_vbmeta_a};" \
 	"name=vbmeta_b,size=64K,uuid=${uuid_gpt_vbmeta_b};" \
 	"name=recovery,size=64M,uuid=${uuid_gpt_recovery};" \
 	"name=super,size=2560M,uuid=${uuid_gpt_super};" \
 	"name=metadata,size=16M,uuid=${uuid_gpt_metadata};" \
 	"name=userdata,size=-,uuid=${uuid_gpt_userdata}"
 #endif /* PARTS_DEFAULT */

 #if defined(CONFIG_CMD_AVB)
 #define AVB_VERIFY_CHECK "if run avb_verify; then " \
 				"echo AVB verification OK.;" \
 				"set bootargs $bootargs $avb_bootargs;" \
 			"else " \
 				"echo AVB verification failed.;" \
 			"exit; fi;"
 #define AVB_VERIFY_CMD "avb_verify=avb init 1; avb verify $slot_suffix;\0"
 #else
 #define AVB_VERIFY_CHECK ""
 #define AVB_VERIFY_CMD ""
 #endif

 #define CONTROL_PARTITION "misc"

 #if defined(CONFIG_CMD_AB_SELECT)
 #define AB_SELECT_SLOT \
 	"if part number mmc 1 " CONTROL_PARTITION " control_part_number; " \
 	"then " \
 		"echo " CONTROL_PARTITION \
 			" partition number:${control_part_number};" \
 		"ab_select slot_name mmc ${mmcdev}:${control_part_number};" \
 	"else " \
 		"echo " CONTROL_PARTITION " partition not found;" \
 		"exit;" \
 	"fi;" \
 	"setenv slot_suffix _${slot_name};"
 #define AB_SELECT_ARGS \
 	"setenv bootargs_ab androidboot.slot_suffix=${slot_suffix}; " \
 	"echo A/B cmdline addition: ${bootargs_ab};" \
 	"setenv bootargs ${bootargs} ${bootargs_ab};"
 #else
 #define AB_SELECT_SLOT ""
 #define AB_SELECT_ARGS ""
 #endif

 /*
  * Prepares complete device tree blob for current board (for Android boot).
  *
  * Boot image or recovery image should be loaded into $loadaddr prior to running
  * these commands. The logic of these commnads is next:
  *
  *   1. Read correct DTB for current SoC/board from boot image in $loadaddr
  *      to $fdtaddr
  *   2. Merge all needed DTBO for current board from 'dtbo' partition into read
  *      DTB
  *   3. User should provide $fdtaddr as 3rd argument to 'bootm'
  */
 #define PREPARE_FDT \
 	"echo Preparing FDT...; " \
 	"if test $board_name = am57xx_evm_reva3; then " \
 		"echo \"  Reading DTBO partition...\"; " \
 		"part start mmc ${mmcdev} dtbo${slot_suffix} p_dtbo_start; " \
 		"part size mmc ${mmcdev} dtbo${slot_suffix} p_dtbo_size; " \
 		"mmc read ${dtboaddr} ${p_dtbo_start} ${p_dtbo_size}; " \
 		"echo \"  Reading DTB for AM57x EVM RevA3...\"; " \
 		"abootimg get dtb --index=0 dtb_start dtb_size; " \
 		"cp.b $dtb_start $fdtaddr $dtb_size; " \
 		"fdt addr $fdtaddr 0x80000; " \
 		"echo \"  Applying DTBOs for AM57x EVM RevA3...\"; " \
 		"adtimg addr $dtboaddr; " \
 		"adtimg get dt --index=0 dtbo0_addr dtbo0_size; " \
 		"fdt apply $dtbo0_addr; " \
 		"adtimg get dt --index=1 dtbo1_addr dtbo1_size; " \
 		"fdt apply $dtbo1_addr; " \
 	"elif test $board_name = beagle_x15_revc; then " \
 		"echo \"  Reading DTB for Beagle X15 RevC...\"; " \
 		"abootimg get dtb --index=0 dtb_start dtb_size; " \
 		"cp.b $dtb_start $fdtaddr $dtb_size; " \
 		"fdt addr $fdtaddr 0x80000; " \
 	"else " \
 		"echo Error: Android boot is not supported for $board_name; " \
 		"exit; " \
 	"fi; " \

 #define DEFAULT_COMMON_BOOT_TI_ARGS \
 	"console=" CONSOLEDEV ",115200n8\0" \
 	"fdtfile=undefined\0" \
 	"finduuid=part uuid mmc 0:2 uuid\0" \
 	"usbtty=cdc_acm\0" \
 	"vram=16M\0" \
 	AVB_VERIFY_CMD \
 	"partitions=" PARTS_DEFAULT "\0" \
 	"optargs=\0" \
 	"dofastboot=0\0" \
 	"emmc_android_boot=" \
 		"setenv mmcdev 1; " \
 		"mmc dev $mmcdev; " \
 		"mmc rescan; " \
 		AB_SELECT_SLOT \
 		"if bcb load " __stringify(CONFIG_FASTBOOT_FLASH_MMC_DEV) " " \
 		CONTROL_PARTITION "; then " \
 			"setenv ardaddr -; " \
 			"if bcb test command = bootonce-bootloader; then " \
 				"echo Android: Bootloader boot...; " \
 				"bcb clear command; bcb store; " \
 				"fastboot 1; " \
 				"exit; " \
 			"elif bcb test command = boot-recovery; then " \
 				"echo Android: Recovery boot...; " \
 				"setenv ardaddr $loadaddr;" \
 				"setenv apart recovery; " \
 			"else " \
 				"echo Android: Normal boot...; " \
 				"setenv ardaddr $loadaddr; " \
 				"setenv apart boot${slot_suffix}; " \
 			"fi; " \
 		"else " \
 			"echo Warning: BCB is corrupted or does not exist; " \
 			"echo Android: Normal boot...; " \
 		"fi; " \
 		"setenv eval_bootargs setenv bootargs $bootargs; " \
 		"run eval_bootargs; " \
 		"setenv machid fe6; " \
 		AVB_VERIFY_CHECK \
 		AB_SELECT_ARGS \
 		"if part start mmc $mmcdev $apart boot_start; then " \
 			"part size mmc $mmcdev $apart boot_size; " \
 			"mmc read $loadaddr $boot_start $boot_size; " \
 			PREPARE_FDT \
 			"bootm $loadaddr $ardaddr $fdtaddr; " \
 		"else " \
 			"echo $apart partition not found; " \
 			"exit; " \
 		"fi;\0"

 #define DEFAULT_FDT_TI_ARGS \
 	"findfdt="\
 		"if test $board_name = omap5_uevm; then " \
 			"setenv fdtfile omap5-uevm.dtb; fi; " \
 		"if test $board_name = dra7xx; then " \
 			"setenv fdtfile dra7-evm.dtb; fi;" \
 		"if test $board_name = dra72x-revc; then " \
 			"setenv fdtfile dra72-evm-revc.dtb; fi;" \
 		"if test $board_name = dra72x; then " \
 			"setenv fdtfile dra72-evm.dtb; fi;" \
 		"if test $board_name = dra71x; then " \
 			"setenv fdtfile dra71-evm.dtb; fi;" \
 		"if test $board_name = dra76x_acd; then " \
 			"setenv fdtfile dra76-evm.dtb; fi;" \
 		"if test $board_name = beagle_x15; then " \
 			"setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
 		"if test $board_name = beagle_x15_revb1; then " \
 			"setenv fdtfile am57xx-beagle-x15-revb1.dtb; fi;" \
 		"if test $board_name = beagle_x15_revc; then " \
 			"setenv fdtfile am57xx-beagle-x15-revc.dtb; fi;" \
 		"if test $board_name = am5729_beagleboneai; then " \
 			"setenv fdtfile am5729-beagleboneai.dtb; fi;" \
 		"if test $board_name = am572x_idk; then " \
 			"setenv fdtfile am572x-idk.dtb; fi;" \
 		"if test $board_name = am574x_idk; then " \
 			"setenv fdtfile am574x-idk.dtb; fi;" \
 		"if test $board_name = am57xx_evm; then " \
 			"setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
 		"if test $board_name = am57xx_evm_reva3; then " \
 			"setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
 		"if test $board_name = am571x_idk; then " \
 			"setenv fdtfile am571x-idk.dtb; fi;" \
 		"if test $fdtfile = undefined; then " \
 			"echo WARNING: Could not determine device tree to use; fi; \0"

 #define BOOT_TARGET_DEVICES(func) \
 	func(MMC, mmc, 0) \
 	func(MMC, mmc, 1) \
 	func(PXE, pxe, na) \
 	func(DHCP, dhcp, na)

 #include <config_distro_bootcmd.h>

 #define CONFIG_EXTRA_ENV_SETTINGS \
 	DEFAULT_LINUX_BOOT_ENV \
 	DEFAULT_MMC_TI_ARGS \
 	DEFAULT_FIT_TI_ARGS \
 	DEFAULT_COMMON_BOOT_TI_ARGS \
 	DEFAULT_FDT_TI_ARGS \
 	DFUARGS \
 	NETARGS \
 	NANDARGS \
 	BOOTENV

 /*
  * SPL related defines.  The Public RAM memory map the ROM defines the
  * area between 0x40300000 and 0x4031E000 as a download area for OMAP5.
  * On DRA7xx/AM57XX the download area is between 0x40300000 and 0x4037E000.
  * We set CONFIG_SPL_DISPLAY_PRINT to have omap_rev_string() called and
  * print some information.
  */
 #ifdef CONFIG_TI_SECURE_DEVICE
 /*
  * For memory booting on HS parts, the first 4KB of the internal RAM is
  * reserved for secure world use and the flash loader image is
  * preceded by a secure certificate. The SPL will therefore run in internal
  * RAM from address 0x40301350 (0x40300000+0x1000(reserved)+0x350(cert)).
  */
 #define TI_OMAP5_SECURE_BOOT_RESV_SRAM_SZ	0x1000
 /* If no specific start address is specified then the secure EMIF
  * region will be placed at the end of the DDR space. In order to prevent
  * the main u-boot relocation from clobbering that memory and causing a
  * firewall violation, we tell u-boot that memory is protected RAM (PRAM)
  */
 #if (CONFIG_TI_SECURE_EMIF_REGION_START == 0)
 #define CONFIG_PRAM (CONFIG_TI_SECURE_EMIF_TOTAL_REGION_SIZE) >> 10
 #endif
 #else
 /*
  * For all booting on GP parts, the flash loader image is
  * downloaded into internal RAM at address 0x40300000.
  */
 #endif

 #endif /* __CONFIG_TI_OMAP5_COMMON_H */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* (C) Copyright 2013
	* Texas Instruments Incorporated.
	* Sricharan R <r.sricharan@ti.com>
	*
	* Derived from OMAP4 done by:
	* Aneesh V <aneesh@ti.com>
	*
	* TI OMAP5 AND DRA7XX common configuration settings
	*
	* For more details, please see the technical documents listed at
	* http://www.ti.com/product/omap5432
	*/

	#ifndef __CONFIG_TI_OMAP5_COMMON_H
	#define __CONFIG_TI_OMAP5_COMMON_H

	/* Use General purpose timer 1 */
	#define CONFIG_SYS_TIMERBASE GPT2_BASE

	#include <linux/stringify.h>

	#include <asm/arch/cpu.h>
	#include <asm/arch/omap.h>

	#include <configs/ti_armv7_omap.h>

	/*
	* Hardware drivers
	*/
	#define CFG_SYS_NS16550_CLK 48000000

	/*
	* Environment setup
	*/

	#ifndef DFUARGS
	#define DFUARGS
	#endif

	#include <environment/ti/mmc.h>
	#include <environment/ti/nand.h>

	#ifndef CONSOLEDEV
	#define CONSOLEDEV "ttyS2"
	#endif

	#ifndef PARTS_DEFAULT
	/*
	* Default GPT tables for eMMC (Linux and Android). Notes:
	* 1. Keep partitions aligned to erase group size (512 KiB) when possible
	* 2. Keep partitions in sync with DFU_ALT_INFO_EMMC (see dfu.h)
	* 3. Keep 'bootloader' partition (U-Boot proper) start address in sync with
	* CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR (see common/spl/Kconfig)
	*/
	#define PARTS_DEFAULT \
	/* Linux partitions */ \
	"uuid_disk=${uuid_gpt_disk};" \
	"name=bootloader,start=384K,size=1792K,uuid=${uuid_gpt_bootloader};" \
	"name=rootfs,start=2688K,size=-,uuid=${uuid_gpt_rootfs}\0" \
	/* Android partitions */ \
	"partitions_android=" \
	"uuid_disk=${uuid_gpt_disk};" \
	"name=xloader,start=128K,size=256K,uuid=${uuid_gpt_xloader};" \
	"name=bootloader,size=2048K,uuid=${uuid_gpt_bootloader};" \
	"name=uboot-env,start=2432K,size=256K,uuid=${uuid_gpt_reserved};" \
	"name=misc,size=128K,uuid=${uuid_gpt_misc};" \
	"name=boot_a,size=20M,uuid=${uuid_gpt_boot_a};" \
	"name=boot_b,size=20M,uuid=${uuid_gpt_boot_b};" \
	"name=dtbo_a,size=8M,uuid=${uuid_gpt_dtbo_a};" \
	"name=dtbo_b,size=8M,uuid=${uuid_gpt_dtbo_b};" \
	"name=vbmeta_a,size=64K,uuid=${uuid_gpt_vbmeta_a};" \
	"name=vbmeta_b,size=64K,uuid=${uuid_gpt_vbmeta_b};" \
	"name=recovery,size=64M,uuid=${uuid_gpt_recovery};" \
	"name=super,size=2560M,uuid=${uuid_gpt_super};" \
	"name=metadata,size=16M,uuid=${uuid_gpt_metadata};" \
	"name=userdata,size=-,uuid=${uuid_gpt_userdata}"
	#endif /* PARTS_DEFAULT */

	#if defined(CONFIG_CMD_AVB)
	#define AVB_VERIFY_CHECK "if run avb_verify; then " \
	"echo AVB verification OK.;" \
	"set bootargs $bootargs $avb_bootargs;" \
	"else " \
	"echo AVB verification failed.;" \
	"exit; fi;"
	#define AVB_VERIFY_CMD "avb_verify=avb init 1; avb verify $slot_suffix;\0"
	#else
	#define AVB_VERIFY_CHECK ""
	#define AVB_VERIFY_CMD ""
	#endif

	#define CONTROL_PARTITION "misc"

	#if defined(CONFIG_CMD_AB_SELECT)
	#define AB_SELECT_SLOT \
	"if part number mmc 1 " CONTROL_PARTITION " control_part_number; " \
	"then " \
	"echo " CONTROL_PARTITION \
	" partition number:${control_part_number};" \
	"ab_select slot_name mmc ${mmcdev}:${control_part_number};" \
	"else " \
	"echo " CONTROL_PARTITION " partition not found;" \
	"exit;" \
	"fi;" \
	"setenv slot_suffix _${slot_name};"
	#define AB_SELECT_ARGS \
	"setenv bootargs_ab androidboot.slot_suffix=${slot_suffix}; " \
	"echo A/B cmdline addition: ${bootargs_ab};" \
	"setenv bootargs ${bootargs} ${bootargs_ab};"
	#else
	#define AB_SELECT_SLOT ""
	#define AB_SELECT_ARGS ""
	#endif

	/*
	* Prepares complete device tree blob for current board (for Android boot).
	*
	* Boot image or recovery image should be loaded into $loadaddr prior to running
	* these commands. The logic of these commnads is next:
	*
	* 1. Read correct DTB for current SoC/board from boot image in $loadaddr
	* to $fdtaddr
	* 2. Merge all needed DTBO for current board from 'dtbo' partition into read
	* DTB
	* 3. User should provide $fdtaddr as 3rd argument to 'bootm'
	*/
	#define PREPARE_FDT \
	"echo Preparing FDT...; " \
	"if test $board_name = am57xx_evm_reva3; then " \
	"echo \" Reading DTBO partition...\"; " \
	"part start mmc ${mmcdev} dtbo${slot_suffix} p_dtbo_start; " \
	"part size mmc ${mmcdev} dtbo${slot_suffix} p_dtbo_size; " \
	"mmc read ${dtboaddr} ${p_dtbo_start} ${p_dtbo_size}; " \
	"echo \" Reading DTB for AM57x EVM RevA3...\"; " \
	"abootimg get dtb --index=0 dtb_start dtb_size; " \
	"cp.b $dtb_start $fdtaddr $dtb_size; " \
	"fdt addr $fdtaddr 0x80000; " \
	"echo \" Applying DTBOs for AM57x EVM RevA3...\"; " \
	"adtimg addr $dtboaddr; " \
	"adtimg get dt --index=0 dtbo0_addr dtbo0_size; " \
	"fdt apply $dtbo0_addr; " \
	"adtimg get dt --index=1 dtbo1_addr dtbo1_size; " \
	"fdt apply $dtbo1_addr; " \
	"elif test $board_name = beagle_x15_revc; then " \
	"echo \" Reading DTB for Beagle X15 RevC...\"; " \
	"abootimg get dtb --index=0 dtb_start dtb_size; " \
	"cp.b $dtb_start $fdtaddr $dtb_size; " \
	"fdt addr $fdtaddr 0x80000; " \
	"else " \
	"echo Error: Android boot is not supported for $board_name; " \
	"exit; " \
	"fi; " \

	#define DEFAULT_COMMON_BOOT_TI_ARGS \
	"console=" CONSOLEDEV ",115200n8\0" \
	"fdtfile=undefined\0" \
	"finduuid=part uuid mmc 0:2 uuid\0" \
	"usbtty=cdc_acm\0" \
	"vram=16M\0" \
	AVB_VERIFY_CMD \
	"partitions=" PARTS_DEFAULT "\0" \
	"optargs=\0" \
	"dofastboot=0\0" \
	"emmc_android_boot=" \
	"setenv mmcdev 1; " \
	"mmc dev $mmcdev; " \
	"mmc rescan; " \
	AB_SELECT_SLOT \
	"if bcb load " __stringify(CONFIG_FASTBOOT_FLASH_MMC_DEV) " " \
	CONTROL_PARTITION "; then " \
	"setenv ardaddr -; " \
	"if bcb test command = bootonce-bootloader; then " \
	"echo Android: Bootloader boot...; " \
	"bcb clear command; bcb store; " \
	"fastboot 1; " \
	"exit; " \
	"elif bcb test command = boot-recovery; then " \
	"echo Android: Recovery boot...; " \
	"setenv ardaddr $loadaddr;" \
	"setenv apart recovery; " \
	"else " \
	"echo Android: Normal boot...; " \
	"setenv ardaddr $loadaddr; " \
	"setenv apart boot${slot_suffix}; " \
	"fi; " \
	"else " \
	"echo Warning: BCB is corrupted or does not exist; " \
	"echo Android: Normal boot...; " \
	"fi; " \
	"setenv eval_bootargs setenv bootargs $bootargs; " \
	"run eval_bootargs; " \
	"setenv machid fe6; " \
	AVB_VERIFY_CHECK \
	AB_SELECT_ARGS \
	"if part start mmc $mmcdev $apart boot_start; then " \
	"part size mmc $mmcdev $apart boot_size; " \
	"mmc read $loadaddr $boot_start $boot_size; " \
	PREPARE_FDT \
	"bootm $loadaddr $ardaddr $fdtaddr; " \
	"else " \
	"echo $apart partition not found; " \
	"exit; " \
	"fi;\0"

	#define DEFAULT_FDT_TI_ARGS \
	"findfdt="\
	"if test $board_name = omap5_uevm; then " \
	"setenv fdtfile omap5-uevm.dtb; fi; " \
	"if test $board_name = dra7xx; then " \
	"setenv fdtfile dra7-evm.dtb; fi;" \
	"if test $board_name = dra72x-revc; then " \
	"setenv fdtfile dra72-evm-revc.dtb; fi;" \
	"if test $board_name = dra72x; then " \
	"setenv fdtfile dra72-evm.dtb; fi;" \
	"if test $board_name = dra71x; then " \
	"setenv fdtfile dra71-evm.dtb; fi;" \
	"if test $board_name = dra76x_acd; then " \
	"setenv fdtfile dra76-evm.dtb; fi;" \
	"if test $board_name = beagle_x15; then " \
	"setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
	"if test $board_name = beagle_x15_revb1; then " \
	"setenv fdtfile am57xx-beagle-x15-revb1.dtb; fi;" \
	"if test $board_name = beagle_x15_revc; then " \
	"setenv fdtfile am57xx-beagle-x15-revc.dtb; fi;" \
	"if test $board_name = am5729_beagleboneai; then " \
	"setenv fdtfile am5729-beagleboneai.dtb; fi;" \
	"if test $board_name = am572x_idk; then " \
	"setenv fdtfile am572x-idk.dtb; fi;" \
	"if test $board_name = am574x_idk; then " \
	"setenv fdtfile am574x-idk.dtb; fi;" \
	"if test $board_name = am57xx_evm; then " \
	"setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
	"if test $board_name = am57xx_evm_reva3; then " \
	"setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
	"if test $board_name = am571x_idk; then " \
	"setenv fdtfile am571x-idk.dtb; fi;" \
	"if test $fdtfile = undefined; then " \
	"echo WARNING: Could not determine device tree to use; fi; \0"

	#define BOOT_TARGET_DEVICES(func) \
	func(MMC, mmc, 0) \
	func(MMC, mmc, 1) \
	func(PXE, pxe, na) \
	func(DHCP, dhcp, na)

	#include <config_distro_bootcmd.h>

	#define CONFIG_EXTRA_ENV_SETTINGS \
	DEFAULT_LINUX_BOOT_ENV \
	DEFAULT_MMC_TI_ARGS \
	DEFAULT_FIT_TI_ARGS \
	DEFAULT_COMMON_BOOT_TI_ARGS \
	DEFAULT_FDT_TI_ARGS \
	DFUARGS \
	NETARGS \
	NANDARGS \
	BOOTENV

	/*
	* SPL related defines. The Public RAM memory map the ROM defines the
	* area between 0x40300000 and 0x4031E000 as a download area for OMAP5.
	* On DRA7xx/AM57XX the download area is between 0x40300000 and 0x4037E000.
	* We set CONFIG_SPL_DISPLAY_PRINT to have omap_rev_string() called and
	* print some information.
	*/
	#ifdef CONFIG_TI_SECURE_DEVICE
	/*
	* For memory booting on HS parts, the first 4KB of the internal RAM is
	* reserved for secure world use and the flash loader image is
	* preceded by a secure certificate. The SPL will therefore run in internal
	* RAM from address 0x40301350 (0x40300000+0x1000(reserved)+0x350(cert)).
	*/
	#define TI_OMAP5_SECURE_BOOT_RESV_SRAM_SZ 0x1000
	/* If no specific start address is specified then the secure EMIF
	* region will be placed at the end of the DDR space. In order to prevent
	* the main u-boot relocation from clobbering that memory and causing a
	* firewall violation, we tell u-boot that memory is protected RAM (PRAM)
	*/
	#if (CONFIG_TI_SECURE_EMIF_REGION_START == 0)
	#define CONFIG_PRAM (CONFIG_TI_SECURE_EMIF_TOTAL_REGION_SIZE) >> 10
	#endif
	#else
	/*
	* For all booting on GP parts, the flash loader image is
	* downloaded into internal RAM at address 0x40300000.
	*/
	#endif

	#endif /* __CONFIG_TI_OMAP5_COMMON_H */