| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * (C) Copyright 2007-2008 |
| * Stelian Pop <stelian@popies.net> |
| * Lead Tech Design <www.leadtechdesign.com> |
| */ |
| |
| #include <common.h> |
| #include <debug_uart.h> |
| #include <init.h> |
| #include <net.h> |
| #include <asm/global_data.h> |
| #include <asm/io.h> |
| #include <asm/arch/at91sam9260_matrix.h> |
| #include <asm/arch/at91sam9_smc.h> |
| #include <asm/arch/at91_common.h> |
| #include <asm/arch/clk.h> |
| #include <asm/arch/gpio.h> |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| /* ------------------------------------------------------------------------- */ |
| /* |
| * Miscelaneous platform dependent initialisations |
| */ |
| |
| #ifdef CONFIG_CMD_NAND |
| static void at91sam9260ek_nand_hw_init(void) |
| { |
| struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; |
| struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX; |
| unsigned long csa; |
| |
| /* Assign CS3 to NAND/SmartMedia Interface */ |
| csa = readl(&matrix->ebicsa); |
| csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA; |
| writel(csa, &matrix->ebicsa); |
| |
| /* Configure SMC CS3 for NAND/SmartMedia */ |
| writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) | |
| AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0), |
| &smc->cs[3].setup); |
| writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) | |
| AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3), |
| &smc->cs[3].pulse); |
| writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5), |
| &smc->cs[3].cycle); |
| writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | |
| AT91_SMC_MODE_EXNW_DISABLE | |
| #ifdef CONFIG_SYS_NAND_DBW_16 |
| AT91_SMC_MODE_DBW_16 | |
| #else /* CONFIG_SYS_NAND_DBW_8 */ |
| AT91_SMC_MODE_DBW_8 | |
| #endif |
| AT91_SMC_MODE_TDF_CYCLE(2), |
| &smc->cs[3].mode); |
| |
| /* Configure RDY/BSY */ |
| at91_set_gpio_input(CFG_SYS_NAND_READY_PIN, 1); |
| |
| /* Enable NandFlash */ |
| at91_set_gpio_output(CFG_SYS_NAND_ENABLE_PIN, 1); |
| |
| } |
| #endif |
| |
| #ifdef CONFIG_DEBUG_UART_BOARD_INIT |
| void board_debug_uart_init(void) |
| { |
| at91_seriald_hw_init(); |
| } |
| #endif |
| |
| #ifdef CONFIG_BOARD_EARLY_INIT_F |
| int board_early_init_f(void) |
| { |
| return 0; |
| } |
| #endif |
| |
| int board_init(void) |
| { |
| /* adress of boot parameters */ |
| gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; |
| |
| #ifdef CONFIG_CMD_NAND |
| at91sam9260ek_nand_hw_init(); |
| #endif |
| return 0; |
| } |
| |
| int dram_init(void) |
| { |
| gd->ram_size = get_ram_size( |
| (void *)CONFIG_SYS_SDRAM_BASE, |
| CONFIG_SYS_SDRAM_SIZE); |
| return 0; |
| } |
| |
| #ifdef CONFIG_RESET_PHY_R |
| void reset_phy(void) |
| { |
| } |
| #endif |