rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/doc/README.m5373evb b/doc/README.m5373evb
index b2ef4a5..4781d94 100644
--- a/doc/README.m5373evb
+++ b/doc/README.m5373evb
@@ -67,12 +67,12 @@
CONFIG_M5373EVB -- define for M5373EVB board
CONFIG_MCFUART -- define to use common CF Uart driver
-CFG_UART_PORT -- define UART port number, start with 0, 1 and 2
+CONFIG_SYS_UART_PORT -- define UART port number, start with 0, 1 and 2
CONFIG_BAUDRATE -- define UART baudrate
CONFIG_MCFRTC -- define to use common CF RTC driver
-CFG_MCFRTC_BASE -- provide base address for RTC in immap.h
-CFG_RTC_OSCILLATOR -- define RTC clock frequency
+CONFIG_SYS_MCFRTC_BASE -- provide base address for RTC in immap.h
+CONFIG_SYS_RTC_OSCILLATOR -- define RTC clock frequency
RTC_DEBUG -- define to show RTC debug message
CONFIG_CMD_DATE -- enable to use date feature in u-boot
@@ -80,11 +80,11 @@
CONFIG_NET_MULTI -- define to use multi FEC in u-boot
CONFIG_MII -- enable to use MII driver
CONFIG_CF_DOMII -- enable to use MII feature in cmd_mii.c
-CFG_DISCOVER_PHY -- enable PHY discovery
-CFG_RX_ETH_BUFFER -- Set FEC Receive buffer
-CFG_FAULT_ECHO_LINK_DOWN--
-CFG_FEC0_PINMUX -- Set FEC0 Pin configuration
-CFG_FEC0_MIIBASE -- Set FEC0 MII base register
+CONFIG_SYS_DISCOVER_PHY -- enable PHY discovery
+CONFIG_SYS_RX_ETH_BUFFER -- Set FEC Receive buffer
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN--
+CONFIG_SYS_FEC0_PINMUX -- Set FEC0 Pin configuration
+CONFIG_SYS_FEC0_MIIBASE -- Set FEC0 MII base register
MCFFEC_TOUT_LOOP -- set FEC timeout loop
CONFIG_MCFTMR -- define to use DMA timer
@@ -93,22 +93,22 @@
CONFIG_FSL_I2C -- define to use FSL common I2C driver
CONFIG_HARD_I2C -- define for I2C hardware support
CONFIG_SOFT_I2C -- define for I2C bit-banged
-CFG_I2C_SPEED -- define for I2C speed
-CFG_I2C_SLAVE -- define for I2C slave address
-CFG_I2C_OFFSET -- define for I2C base address offset
-CFG_IMMR -- define for MBAR offset
+CONFIG_SYS_I2C_SPEED -- define for I2C speed
+CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
+CONFIG_SYS_I2C_OFFSET -- define for I2C base address offset
+CONFIG_SYS_IMMR -- define for MBAR offset
-CFG_MBAR -- define MBAR offset
+CONFIG_SYS_MBAR -- define MBAR offset
CONFIG_MONITOR_IS_IN_RAM -- Not support
-CFG_INIT_RAM_ADDR -- defines the base address of the MCF5373 internal SRAM
+CONFIG_SYS_INIT_RAM_ADDR -- defines the base address of the MCF5373 internal SRAM
-CFG_CSn_BASE -- defines the Chip Select Base register
-CFG_CSn_MASK -- defines the Chip Select Mask register
-CFG_CSn_CTRL -- defines the Chip Select Control register
+CONFIG_SYS_CSn_BASE -- defines the Chip Select Base register
+CONFIG_SYS_CSn_MASK -- defines the Chip Select Mask register
+CONFIG_SYS_CSn_CTRL -- defines the Chip Select Control register
-CFG_SDRAM_BASE -- defines the DRAM Base
+CONFIG_SYS_SDRAM_BASE -- defines the DRAM Base
2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL
===========================================