diff --git a/doc/README.m5373evb b/doc/README.m5373evb
index b2ef4a5..4781d94 100644
--- a/doc/README.m5373evb
+++ b/doc/README.m5373evb
@@ -67,12 +67,12 @@
 CONFIG_M5373EVB		-- define for M5373EVB board
 
 CONFIG_MCFUART		-- define to use common CF Uart driver
-CFG_UART_PORT		-- define UART port number, start with 0, 1 and 2
+CONFIG_SYS_UART_PORT		-- define UART port number, start with 0, 1 and 2
 CONFIG_BAUDRATE		-- define UART baudrate
 
 CONFIG_MCFRTC		-- define to use common CF RTC driver
-CFG_MCFRTC_BASE		-- provide base address for RTC in immap.h
-CFG_RTC_OSCILLATOR	-- define RTC clock frequency
+CONFIG_SYS_MCFRTC_BASE		-- provide base address for RTC in immap.h
+CONFIG_SYS_RTC_OSCILLATOR	-- define RTC clock frequency
 RTC_DEBUG		-- define to show RTC debug message
 CONFIG_CMD_DATE		-- enable to use date feature in u-boot
 
@@ -80,11 +80,11 @@
 CONFIG_NET_MULTI	-- define to use multi FEC in u-boot
 CONFIG_MII		-- enable to use MII driver
 CONFIG_CF_DOMII		-- enable to use MII feature in cmd_mii.c
-CFG_DISCOVER_PHY	-- enable PHY discovery
-CFG_RX_ETH_BUFFER	-- Set FEC Receive buffer
-CFG_FAULT_ECHO_LINK_DOWN--
-CFG_FEC0_PINMUX		-- Set FEC0 Pin configuration
-CFG_FEC0_MIIBASE	-- Set FEC0 MII base register
+CONFIG_SYS_DISCOVER_PHY	-- enable PHY discovery
+CONFIG_SYS_RX_ETH_BUFFER	-- Set FEC Receive buffer
+CONFIG_SYS_FAULT_ECHO_LINK_DOWN--
+CONFIG_SYS_FEC0_PINMUX		-- Set FEC0 Pin configuration
+CONFIG_SYS_FEC0_MIIBASE	-- Set FEC0 MII base register
 MCFFEC_TOUT_LOOP	-- set FEC timeout loop
 
 CONFIG_MCFTMR		-- define to use DMA timer
@@ -93,22 +93,22 @@
 CONFIG_FSL_I2C		-- define to use FSL common I2C driver
 CONFIG_HARD_I2C		-- define for I2C hardware support
 CONFIG_SOFT_I2C		-- define for I2C bit-banged
-CFG_I2C_SPEED		-- define for I2C speed
-CFG_I2C_SLAVE		-- define for I2C slave address
-CFG_I2C_OFFSET		-- define for I2C base address offset
-CFG_IMMR		-- define for MBAR offset
+CONFIG_SYS_I2C_SPEED		-- define for I2C speed
+CONFIG_SYS_I2C_SLAVE		-- define for I2C slave address
+CONFIG_SYS_I2C_OFFSET		-- define for I2C base address offset
+CONFIG_SYS_IMMR		-- define for MBAR offset
 
-CFG_MBAR		-- define MBAR offset
+CONFIG_SYS_MBAR		-- define MBAR offset
 
 CONFIG_MONITOR_IS_IN_RAM -- Not support
 
-CFG_INIT_RAM_ADDR	-- defines the base address of the MCF5373 internal SRAM
+CONFIG_SYS_INIT_RAM_ADDR	-- defines the base address of the MCF5373 internal SRAM
 
-CFG_CSn_BASE	-- defines the Chip Select Base register
-CFG_CSn_MASK	-- defines the Chip Select Mask register
-CFG_CSn_CTRL	-- defines the Chip Select Control register
+CONFIG_SYS_CSn_BASE	-- defines the Chip Select Base register
+CONFIG_SYS_CSn_MASK	-- defines the Chip Select Mask register
+CONFIG_SYS_CSn_CTRL	-- defines the Chip Select Control register
 
-CFG_SDRAM_BASE	-- defines the DRAM Base
+CONFIG_SYS_SDRAM_BASE	-- defines the DRAM Base
 
 2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL
 ===========================================