blob: 90492f4fdb6c1b903f4b11d39abe1270de690e43 [file] [log] [blame]
/*
* (C) Copyright 2014
* Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de
*
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
*/
#define CONFIG_E300 1 /* E300 family */
#define CONFIG_MPC83xx 1 /* MPC83xx family */
#define CONFIG_MPC830x 1 /* MPC830x family */
#define CONFIG_MPC8308 1 /* MPC8308 CPU specific */
#define CONFIG_STRIDER 1 /* STRIDER board specific */
#define CONFIG_SYS_TEXT_BASE 0xFE000000
#ifdef CONFIG_STRIDER_CPU_DP
#define CONFIG_IDENT_STRING " strider cpu dp 0.01"
#elif defined(CONFIG_STRIDER_CPU)
#define CONFIG_IDENT_STRING " strider cpu 0.01"
#elif defined(CONFIG_STRIDER_CON_DP)
#define CONFIG_IDENT_STRING " strider con dp 0.01"
#else
#define CONFIG_IDENT_STRING " strider con 0.01"
#endif
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_EARLY_INIT_R
#define CONFIG_LAST_STAGE_INIT
#define CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
#define CONFIG_GENERIC_MMC
#define CONFIG_DOS_PARTITION
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_CMD_FPGAD
#define CONFIG_CMD_IOLOOP
/*
* System Clock Setup
*/
#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
/*
* Hardware Reset Configuration Word
* if CLKIN is 66.66MHz, then
* CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
* We choose the A type silicon as default, so the core is 400Mhz.
*/
#define CONFIG_SYS_HRCW_LOW (\
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
HRCWL_DDR_TO_SCB_CLK_2X1 |\
HRCWL_SVCOD_DIV_2 |\
HRCWL_CSB_TO_CLKIN_4X1 |\
HRCWL_CORE_TO_CSB_3X1)
/*
* There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
* in 8308's HRCWH according to the manual, but original Freescale's
* code has them and I've expirienced some problems using the board
* with BDI3000 attached when I've tried to set these bits to zero
* (UART doesn't work after the 'reset run' command).
*/
#define CONFIG_SYS_HRCW_HIGH (\
HRCWH_PCI_HOST |\
HRCWH_PCI1_ARBITER_ENABLE |\
HRCWH_CORE_ENABLE |\
HRCWH_FROM_0XFFF00100 |\
HRCWH_BOOTSEQ_DISABLE |\
HRCWH_SW_WATCHDOG_DISABLE |\
HRCWH_ROM_LOC_LOCAL_16BIT |\
HRCWH_RL_EXT_LEGACY |\
HRCWH_TSEC1M_IN_MII |\
HRCWH_TSEC2M_IN_RGMII |\
HRCWH_BIG_ENDIAN)
/*
* System IO Config
*/
#define CONFIG_SYS_SICRH (\
SICRH_ESDHC_A_SD |\
SICRH_ESDHC_B_SD |\
SICRH_ESDHC_C_SD |\
SICRH_GPIO_A_GPIO |\
SICRH_GPIO_B_GPIO |\
SICRH_IEEE1588_A_GPIO |\
SICRH_USB |\
SICRH_GTM_GPIO |\
SICRH_IEEE1588_B_GPIO |\
SICRH_ETSEC2_GPIO |\
SICRH_GPIOSEL_1 |\
SICRH_TMROBI_V3P3 |\
SICRH_TSOBI1_V2P5 |\
SICRH_TSOBI2_V2P5) /* 0x0037f103 */
#define CONFIG_SYS_SICRL (\
SICRL_SPI_PF0 |\
SICRL_UART_PF0 |\
SICRL_IRQ_PF0 |\
SICRL_I2C2_PF0 |\
SICRL_ETSEC1_TX_CLK) /* 0x00000000 */
/*
* IMMR new address
*/
#define CONFIG_SYS_IMMR 0xE0000000
/*
* SERDES
*/
#define CONFIG_FSL_SERDES
#define CONFIG_FSL_SERDES1 0xe3000
/*
* Arbiter Setup
*/
#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */
#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */
/*
* DDR Setup
*/
#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
| DDRCDR_PZ_LOZ \
| DDRCDR_NZ_LOZ \
| DDRCDR_ODT \
| DDRCDR_Q_DRN)
/* 0x7b880001 */
/*
* Manually set up DDR parameters
* consist of one chip NT5TU64M16HG from NANYA
*/
#define CONFIG_SYS_DDR_SIZE 128 /* MB */
#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
| CSCONFIG_ODT_RD_NEVER \
| CSCONFIG_ODT_WR_ONLY_CURRENT \
| CSCONFIG_BANK_BIT_3 \
| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
/* 0x80010102 */
#define CONFIG_SYS_DDR_TIMING_3 0
#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
| (0 << TIMING_CFG0_WRT_SHIFT) \
| (0 << TIMING_CFG0_RRT_SHIFT) \
| (0 << TIMING_CFG0_WWT_SHIFT) \
| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
| (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
/* 0x00260802 */
#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
| (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \
| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
| (7 << TIMING_CFG1_CASLAT_SHIFT) \
| (9 << TIMING_CFG1_REFREC_SHIFT) \
| (2 << TIMING_CFG1_WRREC_SHIFT) \
| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
| (2 << TIMING_CFG1_WRTORD_SHIFT))
/* 0x26279222 */
#define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \
| (4 << TIMING_CFG2_CPO_SHIFT) \
| (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
| (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
/* 0x021848c5 */
#define CONFIG_SYS_DDR_INTERVAL ((0x0824 << SDRAM_INTERVAL_REFINT_SHIFT) \
| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
/* 0x08240100 */
#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
| SDRAM_CFG_SDRAM_TYPE_DDR2 \
| SDRAM_CFG_DBW_16)
/* 0x43100000 */
#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
#define CONFIG_SYS_DDR_MODE ((0x0440 << SDRAM_MODE_ESD_SHIFT) \
| (0x0242 << SDRAM_MODE_SD_SHIFT))
/* ODT 150ohm CL=4, AL=0 on SDRAM */
#define CONFIG_SYS_DDR_MODE2 0x00000000
/*
* Memory test
*/
#define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */
#define CONFIG_SYS_MEMTEST_END 0x07f00000
/*
* The reserved memory
*/
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
/*
* Initial RAM Base Address Setup
*/
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/*
* Local Bus Configuration & Clock Setup
*/
#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR 0x00040000
/*
* FLASH on the Local Bus
*/
#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
#define CONFIG_FLASH_CFI_LEGACY
#define CONFIG_SYS_FLASH_LEGACY_512Kx16
#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is up to 8M */
#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
/* Window base at flash base */
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB)
#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
| BR_PS_16 /* 16 bit port */ \
| BR_MS_GPCM /* MSEL = GPCM */ \
| BR_V) /* valid */
#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
| OR_UPM_XAM \
| OR_GPCM_CSNT \
| OR_GPCM_ACS_DIV2 \
| OR_GPCM_XACS \
| OR_GPCM_SCY_15 \
| OR_GPCM_TRLX_SET \
| OR_GPCM_EHTR_SET)
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 135
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
/*
* FPGA
*/
#define CONFIG_SYS_FPGA0_BASE 0xE0600000
#define CONFIG_SYS_FPGA0_SIZE 1 /* FPGA size is 1M */
/* Window base at FPGA base */
#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_FPGA0_BASE
#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_1MB)
#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FPGA0_BASE \
| BR_PS_16 /* 16 bit port */ \
| BR_MS_GPCM /* MSEL = GPCM */ \
| BR_V) /* valid */
#define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \
| OR_UPM_XAM \
| OR_GPCM_CSNT \
| OR_GPCM_SCY_5 \
| OR_GPCM_TRLX_CLEAR \
| OR_GPCM_EHTR_CLEAR)
#define CONFIG_SYS_FPGA_BASE(k) CONFIG_SYS_FPGA0_BASE
#define CONFIG_SYS_FPGA_DONE(k) 0x0010
#define CONFIG_SYS_FPGA_COUNT 1
#define CONFIG_SYS_MCLINK_MAX 3
#define CONFIG_SYS_FPGA_PTR \
{ (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL }
#define CONFIG_SYS_FPGA_NO_RFL_HI
/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 2
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
/* Pass open firmware flat tree */
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED 400000
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
#define CONFIG_PCA953X /* NXP PCA9554 */
#define CONFIG_CMD_PCA953X
#define CONFIG_CMD_PCA953X_INFO
#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x24, 16}, {0x25, 16}, {0x26, 16}, \
{0x3c, 8}, {0x3d, 8}, {0x3e, 8} }
#define CONFIG_PCA9698 /* NXP PCA9698 */
#define CONFIG_SYS_I2C_IHS
#define CONFIG_SYS_I2C_IHS_CH0
#define CONFIG_SYS_I2C_IHS_SPEED_0 50000
#define CONFIG_SYS_I2C_IHS_SLAVE_0 0x7F
#define CONFIG_SYS_I2C_IHS_CH1
#define CONFIG_SYS_I2C_IHS_SPEED_1 50000
#define CONFIG_SYS_I2C_IHS_SLAVE_1 0x7F
#define CONFIG_SYS_I2C_IHS_CH2
#define CONFIG_SYS_I2C_IHS_SPEED_2 50000
#define CONFIG_SYS_I2C_IHS_SLAVE_2 0x7F
#define CONFIG_SYS_I2C_IHS_CH3
#define CONFIG_SYS_I2C_IHS_SPEED_3 50000
#define CONFIG_SYS_I2C_IHS_SLAVE_3 0x7F
#ifdef CONFIG_STRIDER_CON_DP
#define CONFIG_SYS_I2C_IHS_DUAL
#define CONFIG_SYS_I2C_IHS_CH0_1
#define CONFIG_SYS_I2C_IHS_SPEED_0_1 50000
#define CONFIG_SYS_I2C_IHS_SLAVE_0_1 0x7F
#define CONFIG_SYS_I2C_IHS_CH1_1
#define CONFIG_SYS_I2C_IHS_SPEED_1_1 50000
#define CONFIG_SYS_I2C_IHS_SLAVE_1_1 0x7F
#define CONFIG_SYS_I2C_IHS_CH2_1
#define CONFIG_SYS_I2C_IHS_SPEED_2_1 50000
#define CONFIG_SYS_I2C_IHS_SLAVE_2_1 0x7F
#define CONFIG_SYS_I2C_IHS_CH3_1
#define CONFIG_SYS_I2C_IHS_SPEED_3_1 50000
#define CONFIG_SYS_I2C_IHS_SLAVE_3_1 0x7F
#endif
/*
* Software (bit-bang) I2C driver configuration
*/
#define CONFIG_SYS_I2C_SOFT
#define CONFIG_SOFT_I2C_READ_REPEATED_START
#define CONFIG_SYS_I2C_SOFT_SPEED 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F
#define I2C_SOFT_DECLARATIONS2
#define CONFIG_SYS_I2C_SOFT_SPEED_2 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x7F
#define I2C_SOFT_DECLARATIONS3
#define CONFIG_SYS_I2C_SOFT_SPEED_3 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_3 0x7F
#define I2C_SOFT_DECLARATIONS4
#define CONFIG_SYS_I2C_SOFT_SPEED_4 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_4 0x7F
#if defined(CONFIG_STRIDER_CON) || defined(CONFIG_STRIDER_CON_DP)
#define I2C_SOFT_DECLARATIONS5
#define CONFIG_SYS_I2C_SOFT_SPEED_5 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_5 0x7F
#define I2C_SOFT_DECLARATIONS6
#define CONFIG_SYS_I2C_SOFT_SPEED_6 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_6 0x7F
#define I2C_SOFT_DECLARATIONS7
#define CONFIG_SYS_I2C_SOFT_SPEED_7 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_7 0x7F
#define I2C_SOFT_DECLARATIONS8
#define CONFIG_SYS_I2C_SOFT_SPEED_8 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_8 0x7F
#endif
#ifdef CONFIG_STRIDER_CON_DP
#define I2C_SOFT_DECLARATIONS9
#define CONFIG_SYS_I2C_SOFT_SPEED_9 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_9 0x7F
#define I2C_SOFT_DECLARATIONS10
#define CONFIG_SYS_I2C_SOFT_SPEED_10 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_10 0x7F
#define I2C_SOFT_DECLARATIONS11
#define CONFIG_SYS_I2C_SOFT_SPEED_11 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_11 0x7F
#define I2C_SOFT_DECLARATIONS12
#define CONFIG_SYS_I2C_SOFT_SPEED_12 50000
#define CONFIG_SYS_I2C_SOFT_SLAVE_12 0x7F
#endif
#ifdef CONFIG_STRIDER_CON
#define CONFIG_SYS_ICS8N3QV01_I2C {5, 6, 7, 8}
#define CONFIG_SYS_CH7301_I2C {5, 6, 7, 8}
#define CONFIG_SYS_ADV7611_I2C {5, 6, 7, 8}
#define CONFIG_SYS_DP501_I2C {1, 2, 3, 4}
#define CONFIG_STRIDER_FANS { {10, 0x4c}, {11, 0x4c}, \
{12, 0x4c} }
#elif defined(CONFIG_STRIDER_CON_DP)
#define CONFIG_SYS_ICS8N3QV01_I2C {13, 14, 15, 16, 17, 18, 19, 20}
#define CONFIG_SYS_CH7301_I2C {1, 3, 5, 7}
#define CONFIG_SYS_ADV7611_I2C {1, 3, 5, 7}
#define CONFIG_SYS_DP501_I2C {1, 3, 5, 7, 2, 4, 6, 8}
#define CONFIG_STRIDER_FANS { {10, 0x4c}, {11, 0x4c}, \
{12, 0x4c} }
#elif defined(CONFIG_STRIDER_CPU_DP)
#define CONFIG_SYS_CH7301_I2C {1, 2, 3, 4}
#define CONFIG_SYS_ADV7611_I2C {1, 2, 3, 4}
#define CONFIG_SYS_DP501_I2C {1, 2, 3, 4}
#define CONFIG_STRIDER_FANS { {6, 0x4c}, {7, 0x4c}, \
{8, 0x4c} }
#else
#define CONFIG_SYS_CH7301_I2C {1, 2, 3, 4}
#define CONFIG_SYS_ADV7611_I2C {1, 2, 3, 4}
#define CONFIG_SYS_DP501_I2C {1, 2, 3, 4}
#define CONFIG_STRIDER_FANS { {2, 0x18}, {3, 0x18}, \
{4, 0x18} }
#endif
#ifndef __ASSEMBLY__
void fpga_gpio_set(unsigned int bus, int pin);
void fpga_gpio_clear(unsigned int bus, int pin);
int fpga_gpio_get(unsigned int bus, int pin);
void fpga_control_set(unsigned int bus, int pin);
void fpga_control_clear(unsigned int bus, int pin);
#endif
#ifdef CONFIG_STRIDER_CON
#define I2C_SDA_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0200 : 0x0040)
#define I2C_SCL_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0100 : 0x0020)
#define I2C_FPGA_IDX ((I2C_ADAP_HWNR > 3) ? \
(I2C_ADAP_HWNR - 4) : I2C_ADAP_HWNR)
#elif defined(CONFIG_STRIDER_CON_DP)
#define I2C_SDA_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0040 : 0x0200)
#define I2C_SCL_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0020 : 0x0100)
#define I2C_FPGA_IDX (I2C_ADAP_HWNR % 4)
#else
#define I2C_SDA_GPIO 0x0040
#define I2C_SCL_GPIO 0x0020
#define I2C_FPGA_IDX I2C_ADAP_HWNR
#endif
#ifdef CONFIG_STRIDER_CON_DP
#define I2C_ACTIVE \
do { \
if (I2C_ADAP_HWNR > 7) \
fpga_control_set(I2C_FPGA_IDX, 0x0004); \
else \
fpga_control_clear(I2C_FPGA_IDX, 0x0004); \
} while (0)
#else
#define I2C_ACTIVE { }
#endif
#define I2C_TRISTATE { }
#define I2C_READ \
(fpga_gpio_get(I2C_FPGA_IDX, I2C_SDA_GPIO) ? 1 : 0)
#define I2C_SDA(bit) \
do { \
if (bit) \
fpga_gpio_set(I2C_FPGA_IDX, I2C_SDA_GPIO); \
else \
fpga_gpio_clear(I2C_FPGA_IDX, I2C_SDA_GPIO); \
} while (0)
#define I2C_SCL(bit) \
do { \
if (bit) \
fpga_gpio_set(I2C_FPGA_IDX, I2C_SCL_GPIO); \
else \
fpga_gpio_clear(I2C_FPGA_IDX, I2C_SCL_GPIO); \
} while (0)
#define I2C_DELAY udelay(25) /* 1/4 I2C clock duration */
/*
* Software (bit-bang) MII driver configuration
*/
#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
#define CONFIG_BITBANGMII_MULTI
/*
* OSD Setup
*/
#define CONFIG_SYS_OSD_SCREENS 1
#define CONFIG_SYS_DP501_DIFFERENTIAL
#define CONFIG_SYS_DP501_VCAPCTRL0 0x01 /* DDR mode 0, DE for H/VSYNC */
#ifdef CONFIG_STRIDER_CON_DP
#define CONFIG_SYS_OSD_DH
#endif
/*
* General PCI
* Addresses are mapped 1-1.
*/
#define CONFIG_SYS_PCIE1_BASE 0xA0000000
#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000
#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000
#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
/* enable PCIE clock */
#define CONFIG_SYS_SCCR_PCIEXP1CM 1
#define CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCIE
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
/*
* TSEC
*/
#define CONFIG_TSEC_ENET /* TSEC ethernet support */
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
/*
* TSEC ethernet configuration
*/
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_TSEC1
#define CONFIG_TSEC1_NAME "eTSEC0"
#define TSEC1_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC1_FLAGS 0
/* Options are: eTSEC[0-1] */
#define CONFIG_ETHPRIME "eTSEC0"
/*
* Environment
*/
#if 1
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
#else
#define CONFIG_ENV_IS_NOWHERE
#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* Command line configuration.
*/
#define CONFIG_CMD_PCI
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
#undef CONFIG_ZERO_BOOTDELAY_CHECK /* ignore keypress on bootdelay==0 */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_CONSOLE_INFO_QUIET
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/*
* For booting Linux, the board info and command line data
* have to be in the first 256 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
/*
* Core HID Setup
*/
#define CONFIG_SYS_HID0_INIT 0x000000000
#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
HID0_ENABLE_INSTRUCTION_CACHE | \
HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
#define CONFIG_SYS_HID2 HID2_HBE
/*
* MMU Setup
*/
/* DDR: cache cacheable */
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
/* IMMRBAR, PCI IO and FPGA: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_RW | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
BATU_VP)
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
/* FLASH: icache cacheable, but dcache-inhibit and guarded */
#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
BATL_CACHEINHIBIT | \
BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
/* Stack in dcache: cacheable, no memory coherence */
#define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
#define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
/*
* Environment Configuration
*/
#define CONFIG_ENV_OVERWRITE
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_HAS_ETH0
#endif
#define CONFIG_BAUDRATE 115200
#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */
#define CONFIG_HOSTNAME hrcon
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_PREBOOT /* enable preboot variable */
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS1\0" \
"u-boot=u-boot.bin\0" \
"kernel_addr=1000000\0" \
"fdt_addr=C00000\0" \
"fdtfile=hrcon.dtb\0" \
"load=tftp ${loadaddr} ${u-boot}\0" \
"update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \
" +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
" +${filesize};cp.b ${fileaddr} " \
__stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
"upd=run load update\0" \
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp ${kernel_addr} $bootfile;" \
"tftp ${fdt_addr} $fdtfile;" \
"bootm ${kernel_addr} - ${fdt_addr}"
#define CONFIG_MMCBOOTCOMMAND \
"setenv bootargs root=/dev/mmcblk0p3 rw rootwait " \
"console=$consoledev,$baudrate $othbootargs;" \
"ext2load mmc 0:2 ${kernel_addr} $bootfile;" \
"ext2load mmc 0:2 ${fdt_addr} $fdtfile;" \
"bootm ${kernel_addr} - ${fdt_addr}"
#define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND
#endif /* __CONFIG_H */